Copyright Juniper, 2017 Version 1.10 Page 1 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
Juniper Networks SRX5400, SRX5600, and SRX5800 Services
Gateways
Non-Proprietary FIPS 140-2 Cryptographic Module Security
Policy
Version: 1.10
Date: June 09, 2017
Juniper Networks, Inc.
1133 Innovation Way
Sunnyvale, California 94089
USA
408.745.2000
1.888 JUNIPER
www.juniper.net
Copyright Juniper, 2017 Version 1.10 Page 2 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
Table of Contents
1 Introduction ................................................................................................................... 4
1.1 Hardware and Physical Cryptographic Boundary ....................................................................... 6
1.2 Mode of Operation................................................................................................................... 11
1.3 Zeroization................................................................................................................................ 12
2 Cryptographic Functionality.......................................................................................... 13
2.1 Approved Algorithms................................................................................................................ 13
2.2 Allowed Algorithms .................................................................................................................. 14
2.3 Allowed Protocols..................................................................................................................... 15
2.4 Disallowed Algorithms.............................................................................................................. 16
2.5 Critical Security Parameters ..................................................................................................... 16
3 Roles, Authentication and Services............................................................................... 18
3.1 Roles and Authentication of Operators to Roles ...................................................................... 18
3.2 Authentication Methods........................................................................................................... 18
3.3 Services..................................................................................................................................... 18
3.4 Non-Approved Services ............................................................................................................ 20
4 Self-tests ...................................................................................................................... 21
5 Physical Security Policy................................................................................................. 23
5.1 General Tamper Seal Placement and Application Instructions ................................................ 23
5.2 SRX5400 (13 seals).................................................................................................................... 23
5.3 SRX5600 (18 seals).................................................................................................................... 24
5.4 SRX5800 (24 seals).................................................................................................................... 26
6 Security Rules and Guidance......................................................................................... 28
7 References and Definitions........................................................................................... 29
List of Tables
Table 1 – Cryptographic Module Hardware Configurations.........................................................................4
Table 2 - Security Level of Security Requirements .......................................................................................5
Table 3 - Ports and Interfaces....................................................................................................................11
Table 4 - Data Plane Approved Cryptographic Functions...........................................................................13
Table 5 - Control Plane Authentec Approved Cryptographic Functions.....................................................13
Table 6 - OpenSSL Approved Cryptographic Functions..............................................................................14
Table 7 – Allowed Cryptographic Functions...............................................................................................14
Table 8 – Protocols Allowed in FIPS Mode.................................................................................................15
Table 9 – Critical Security Parameters (CSPs).............................................................................................16
Table 10 – Public Keys ................................................................................................................................17
Table 11 – Authenticated Services .............................................................................................................18
Table 12 – Unauthenticated traffic ............................................................................................................19
Copyright Juniper, 2017 Version 1.10 Page 3 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
Table 13 – CSP Access Rights within Services.............................................................................................19
Table 14 – Authenticated Services .............................................................................................................20
Table 15 – Unauthenticated traffic ............................................................................................................20
Table 16 – Physical Security Inspection Guidelines....................................................................................23
Table 17 – References ................................................................................................................................29
Table 18 – Acronyms and Definitions.........................................................................................................30
Table 19 – Datasheets................................................................................................................................30
List of Figures
Figure 1 – SRX5400 Front View ....................................................................................................................6
Figure 2 – SRX5400 Bottom View.................................................................................................................7
Figure 3 – SRX5600 Profile View ..................................................................................................................7
Figure 4 – SRX5600 Rear View......................................................................................................................8
Figure 5 – SRX5600 Left View.......................................................................................................................8
Figure 6 – SRX5800 Top View.......................................................................................................................9
Figure 7 – SRX5800 Rear View....................................................................................................................10
Figure 8 – SRX5800 Left View.....................................................................................................................10
Figure 9 - SRX5400- Tamper-Evident Seal Locations on Front- Six Seals....................................................24
Figure 10 - SRX5400- Tamper-Evident Seal Locations on Rear- Seven Seals..............................................24
Figure 11 - SRX5600- Tamper-Evident Seal Locations on Front- 11 Seals ..................................................25
Figure 12 - SRX5600- Tamper-Evident Seal Locations on Rear- Seven Seals..............................................25
Figure 13 - SRX5800- Tamper-Evident Seal Locations on Front- 19 Seals ..................................................26
Figure 14 - SRX5800- Tamper-Evident Seal Locations on Rear- Five Seals.................................................27
Copyright Juniper, 2017 Version 1.10 Page 4 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
1 Introduction
The Juniper Networks SRX Series Services Gateways are a series of secure routers that provide essential
capabilities to connect, secure, and manage work force locations sized from handfuls to hundreds of users.
By consolidating fast, highly available switching, routing, security, and applications capabilities in a single
device, enterprises can economically deliver new services, safe connectivity, and a satisfying end user
experience. All models run Juniper’s JUNOS firmware – in this case, a specific FIPS-compliant version called
JUNOS-FIPS, version 12.3X48-D30. The firmware image is junos-srx5000-12.3X48-D30.12-fips.tgz and the
firmware Status service identifies itself as in the “Junos 12.3X48-D30.12 (FIPS edition)”.
This Security Policy covers the SRX5400, SRX5600, and SRX5800 models. They are meant for service
providers, large enterprise networks, and public-sector networks.
The cryptographic modules are defined as multiple-chip standalone modules that execute JUNOS-FIPS
firmware on any of the Juniper Networks SRX-Series gateways listed in the table below.
Table 1 – Cryptographic Module Hardware Configurations
Chassis PN RE PN SCB PN SPC PN IOC PN Power PN Tamper
Seals
SRX5400
SRX5K-RE-
13-20
SRX5K-SCB
SRX5K-SPC-4-
15-320
SRX5K-40GE-
SFP
with AC
HC or DC
JNPR-FIPS-
TAMPER-
LBLS
SRX5K-RE-
1800X4
SRX5K-SCBE
SRX5K-SPC-4-
15-320
SRX-MIC-
10XG-SFPP
SRX5600
SRX5K-RE-
13-20
SRX5K-SCB
SRX5K-SPC-2-
10-40
SRX5K-40GE-
SFP
SRX5K-RE-
1800X4
SRX5K-SCBE
SRX5K-SPC-4-
15-320
SRX-MIC-
10XG-SFPP
SRX5800
SRX5K-RE-
13-20
SRX5K-SCB
SRX5K-SPC-2-
10-40
SRX-MIC-
10XG-SFPP
SRX5K-RE-
1800X4
SRX5K-SCBE
SRX5K-SPC-4-
15-320
SRX-MIC-
10XG-SFPP
The modules are designed to meet FIPS 140-2 Level 2 overall:
Copyright Juniper, 2017 Version 1.10 Page 5 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
Table 2 - Security Level of Security Requirements
Area Description Level
1 Module Specification 2
2 Ports and Interfaces 2
3 Roles and Services 3
4 Finite State Model 2
5 Physical Security 2
6 Operational Environment N/A
7 Key Management 2
8 EMI/EMC 2
9 Self-test 2
10 Design Assurance 3
11 Mitigation of Other Attacks N/A
Overall 2
The modules have a limited operational environment as per the FIPS 140-2 definitions. They include a
firmware load service to support necessary updates. New firmware versions within the scope of this
validation must be validated through the FIPS 140-2 CMVP. Any other firmware loaded into these modules
are out of the scope of this validation and require a separate FIPS 140-2 validation.
The modules do not implement any mitigation of other attacks as defined by FIPS 140-2.
Copyright Juniper, 2017 Version 1.10 Page 6 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
1.1 Hardware and Physical Cryptographic Boundary
The physical forms of the module’s various models are depicted in Figures 1-11 below. For all models, the
cryptographic boundary is defined as the outer edge of the chassis. The modules exclude the power supply
and fan components from the requirements of FIPS 140-2. The power supplies and fans do not contain
any security relevant components and cannot affect the security of the module. The excluded components
are identified with red borders in the following figures. The module does not rely on external devices for
input and output.
Figure 1 – SRX5400 Front View
Copyright Juniper, 2017 Version 1.10 Page 7 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
Figure 2 – SRX5400 Bottom View
Figure 3 – SRX5600 Profile View
Copyright Juniper, 2017 Version 1.10 Page 8 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
Figure 4 – SRX5600 Rear View
Figure 5 – SRX5600 Left View
Copyright Juniper, 2017 Version 1.10 Page 9 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
Figure 6 – SRX5800 Top View
Copyright Juniper, 2017 Version 1.10 Page 10 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
Figure 7 – SRX5800 Rear View
Figure 8 – SRX5800 Left View
Copyright Juniper, 2017 Version 1.10 Page 11 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
Table 3 - Ports and Interfaces
Port Description Logical Interface Type
Ethernet LAN Communications Control in, Data in, Data out, Status out
Serial Console serial port Control in, Status out
Power Power connector Power in
Reset Reset Control in
LED Status indicator lighting Status out
USB Firmware load port Control in, Data in
WAN SHDSL, VDSL, T1, E1 Control in, Data in, Data out, Status out
1.2 Mode of Operation
Follow the instructions in Section 5 to apply the tamper seals to the module. Once the tamper seals have
been applied as shown in this document, the JUNOS-FIPS firmware image is installed on the device, and
integrity and self-tests have run successfully on initial power-on, the module is operating in the Approved
mode. The Crypto-Officer must ensure that the backup image of the firmware is also a JUNOS-FIPS image
by issuing the request system snapshot command.
If the module was previously in a non-Approved mode of operation, the Cryptographic Officer must
zeroize the CSPs by following the instructions in Section 1.3.
Then, the CO must run the following commands to configure SSH to use FIPS Approved and FIPS allowed
algorithms:
co@fips-srx# set system services ssh hostkey-algorithm ssh-ecdsa
co@fips-srx# set system services ssh hostkey-algorithm no-ssh-rsa
co@fips-srx# set system services ssh hostkey-algorithm no-ssh-dss
co@fips-srx# set system services ssh hostkey-algorithm no-ssh-ed25519
co@fips-srx# commit
The CO can change the preference of SSH key exchange methods using the following command:
co@fips-srx# set system services ssh key-exchange <algorithm>
<algorithm> - dh-group14-sha1, ecdh-sha2-nistp256, ecdh-sha2-nistp384,
group-exchange-sha1, or group-exchange-sha2
The CO can change the preference of SSH cipher algorithms using the following command:
co@fips-srx# set system services ssh ciphers <algorithm>
<algorithm> - 3des-cbc, aes128-cbc, aes128-ctr, aes192-cbc, aes192-ctr,
aes256-cbc, aes256-ctr
The CO can change the preference of SSH MAC algorithms or enable additional Approved algorithms using
the following command:
Copyright Juniper, 2017 Version 1.10 Page 12 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
co@fips-srx# set system services ssh macs <algorithm>
<algorithm> - hmac-sha1, hmac-sha1-96, hmac-sha2-256, hmac-sha2-512,
hmac-sha1-96-etm@openssh.com, hmac-sha1-etm@openssh.com, hmac-sha2-256-
etm@openssh.com, hmac-sha2-512-etm@openssh.com
When AES GCM is configured as the encryption-algorithm for IKE or IPsec , the CO must run the following
command to configure the algorithms:
co@fips-srx# set security ike gateway <name> version v2-only
<name> - the user configured name for the IKE gateway
co@fips-srx# commit
The “show version” command will indicate if the module is operating in FIPS mode (e.g. JUNOS Software
Release [12.3X48-D30] (FIPS edition)), run “show system services ssh”, and run “show security
ipsec” to verify that only the FIPS Approved and FIPS allowed algorithms are configured for SSH and
IPsec as specified above.
1.3 Zeroization
The cryptographic module provides a non-Approved mode of operation in which non-Approved
cryptographic algorithms are supported. When transitioning between the non-Approved mode of
operation and the Approved mode of operation, the Cryptographic Officer must run the following
commands to zeroize the Approved mode CSPs:
co@fips-srx> start shell
co@fips-srx% rm –P <keyfile>
<keyfile> - each persistent private or secret key other than the SSH
host keys and the X.509 keys for IKE.
co@fips-srx% rm –P /var/db/certs/common/certificate-request/*
co@fips-srx% exit
co@fips-srx> request system zeroize
Note: The Cryptographic Officer must retain control of the module while zeroization is in process.
Copyright Juniper, 2017 Version 1.10 Page 13 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
2 Cryptographic Functionality
2.1 Approved Algorithms
The module implements the FIPS Approved and Non-Approved but Allowed cryptographic functions listed
in the Tables 4 to 6 below. Table 8 summarizes the high level protocol algorithm support. The module
does not implement algorithms that require vendor affirmation.
Table 4 - Data Plane Approved Cryptographic Functions
CAVP
Cert. Algorithm Mode Description Functions
4070,
4329
AES [197] CBC [38A] Key Sizes: 128, 192, 256 Encrypt, Decrypt
4070 AES [197] GCM [38D]1
Key Sizes: 128, 192, 256 Encrypt, Decrypt, AEAD
2657,
2867
HMAC [198]
SHA-1 λ = 96
Message Authentication
SHA-256 λ = 128
3353,
3571
SHS [180]
SHA-1
SHA-256
Message Digest Generation
2221,
2222
Triple-DES [67] TCBC [38A] Key Size: 192 Encrypt, Decrypt
Table 5 - Control Plane Authentec Approved Cryptographic Functions
Cert Algorithm Mode Description Functions
4054,
4055
AES [197] CBC [38A] Key Sizes: 128, 192, 256 Encrypt, Decrypt
4055 AES [197] GCM [38D]1
Key Sizes: 128, 256 Encrypt, Decrypt, AEAD
926 CVL
IKEv1 [135] SHA 1, 256, 384
Key Derivation
IKEv2 [135] SHA 1, 256, 384
1103,
1104
DSA [186]
(L = 2048, N = 224)
(L = 2048, N = 256)
KeyGen
916,
917
ECDSA[186]
P-256 (SHA 256)
P-384 (SHA {256}, 384)
KeyGen, SigGen, SigVer
2646,
2647
HMAC [198]
SHA-1 λ = 96, 160
Message Authentication, KDF
Primitive
SHA-256 λ = 128, 256
SHA-384 λ = 192, 384
N/A KTS [38F]
(AES Cert. #4054 and HMAC Cert.
#2646), (AES Cert. #4055 and HMAC
Cert. #2647), (Triple-DES Cert. #2224
and HMAC Cert. #2646)
Key Wrapping/Unwrapping
2201,
2202
RSA [186] PKCS1_V1_5
n=2048 (SHA 256)
{n=3072 (SHA 256)}
SigGen, SigVer
1
The SRX5K-SPC-2-10-40 does not support AES GCM.
Copyright Juniper, 2017 Version 1.10 Page 14 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
3341,
3342
SHS [180]
SHA-1
SHA-256
SHA-384
Message Digest Generation
2224 Triple-DES [67] TCBC [38A] Key Size: 192 Encrypt, Decrypt
Table 6 - OpenSSL Approved Cryptographic Functions
CAVP
Cert. Algorithm Mode Description Functions
4056 AES [197]
CBC [38A]
CTR [38A]
Key Sizes: 128, 192, 256 Encrypt, Decrypt
880 CVL SSH [135] SHA 1, 256, 384 Key Derivation
1216,
1399,
1401
DRBG [90A] HMAC SHA-256 Random Bit Generation
1096 DSA [186]
{(2048, 224)}
(2048, 256)
KeyGen
909 ECDSA [186]
{P-224 (SHA 256)}
P-256 (SHA 256)
{P-384 (SHA 256)}
SigGen
{P-224 (SHA 256)}
P-256 (SHA 256)
P-384 (SHA {256}, 384)
KeyGen, SigVer
2648 HMAC [198]
SHA-1 λ = 96, 160
Message Authentication
DRBG Primitive
SHA-256 λ = 256
SHA-512 λ = 512
N/A KTS [38F]
(AES Cert. #4056 and HMAC Cert.
#2648), (Triple-DES Cert. #2223 and
HMAC Cert. #2648)
Key Wrapping/Unwrapping
2087 RSA [186]
n=2048 (SHA 256)
{n=3072 (SHA 256)}
KeyGen, SigGen, SigVer
RSA [186-2] {n=4096 (SHA 256)} {SigGen}
3343 SHS [180]
SHA-1
SHA-256
SHA-384
Message Digest Generation,
KDF Primitive
SHA-512 Message Digest Generation
2223 Triple-DES [67] TCBC [38A] Key Size: 192 Encrypt, Decrypt
2.2 Allowed Algorithms
Table 7 – Allowed Cryptographic Functions
Algorithm Caveat Use
Copyright Juniper, 2017 Version 1.10 Page 15 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
Diffie-Hellman [IG] D.8
Provides between 112 and 192 bits of
encryption strength.
key agreement; key establishment
Elliptic Curve Diffie-
Hellman [IG] D.8
Provides 128 or 192 bits of encryption
strength.
key agreement; key establishment
NDRNG Seeding the DBRG
2.3 Allowed Protocols
Table 8 – Protocols Allowed in FIPS Mode
Protocol Key Exchange Auth Cipher Integrity
IKEv1
Diffie-Hellman (L = 2048, N = 224, 256)
EC Diffie-Hellman P-256, P-384
RSA 2048
Pre-Shared
Secret
ECDSA P-256
ECDSA P-384
Triple-DES CBC
AES CBC
128/192/256
HMAC-SHA-
1-96
HMAC-SHA-
256-128
HMAC-SHA-
384-192
IKEv22 Diffie-Hellman (L = 2048, N = 224, 256)
EC Diffie-Hellman P-256, P-384
RSA 2048
Pre-Shared
Secret
ECDSA P-256
ECDSA P-384
Triple-DES CBC
AES CBC
128/192/256
AES GCM3
128/256
HMAC-SHA-
1-96
HMAC-SHA-
256-128
HMAC-SHA-
384-192
IPsec ESP
IKEv1 with optional:
• Diffie-Hellman (L = 2048, N = 224,
256)
• EC Diffie-Hellman P-256, P-384
IKEv1
3 Key Triple-DES CBC
AES CBC
128/192/256 HMAC-SHA-
1-96
HMAC-SHA-
256-128
IKEv2 with optional:
• Diffie-Hellman (L = 2048, N = 224),
(2048, 256)
• EC Diffie-Hellman P-256, P-384
IKEv2
3 Key Triple-DES CBC
AES CBC
128/192/256
AES GCM4
128/192/256
SSHv2
Diffie-Hellman (L = 2048, 3072, 4096,
6144, 7680, 8192; N = 256, 320, 384,
512, 1024)
EC Diffie-Hellman P-256, P-384
ECDSA P-256
Triple-DES CBC
AES CBC
128/192/256
AES CTR
128/192/256
HMAC-SHA-
1-96
HMAC-SHA-
1
HMAC-SHA-
256
HMAC-SHA-
512
2
IKEv2 generates the SKEYSEED according to RFC7296.
3
The GCM IV is generated according to RFC5282.
4
The GCM IV is generated according to RFC4106.
Copyright Juniper, 2017 Version 1.10 Page 16 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
These protocols have not been reviewed or tested by the CAVP or CMVP.
The IKE and SSH algorithms allow independent selection of key exchange, authentication, cipher and
integrity. In Table 8 above, each column of options for a given protocol is independent, and may be used
in any viable combination. These security functions are also available in the SSH connect (non-compliant)
service.
2.4 Disallowed Algorithms
These algorithms are non-Approved algorithms that are disabled when the module is operated in an
Approved mode of operation.
• ARCFOUR
• Blowfish
• CAST
• HMAC-MD5
• HMAC-RIPEMD160
• UMAC
2.5 Critical Security Parameters
All CSPs and public keys used by the module are described in this section.
Table 9 – Critical Security Parameters (CSPs)
Name Description and usage
DRBG_Seed Seed material used to seed or reseed the DRBG
DRBG_State V and Key values for the HMAC_DRBG
SSH PHK
SSH Private host key. 1st
time SSH is configured, the keys are generated. ECDSA P-256.
Used to identify the host.
SSH DH
SSH Diffie-Hellman private component. Ephemeral Diffie-Hellman private key used in SSH.
Diffie-Hellman (N = 256 bit, 320 bit, 384 bit, 512 bit, or 1024 bit5
), EC Diffie-Hellman P-256,
or EC Diffie-Hellman P-384
SSH-SEK SSH Session Key; Session keys used with SSH. Triple-DES (3key), AES, HMAC.
ESP-SEK IPSec ESP Session Keys. Triple-DES (3 key), AES, HMAC.
IKE-PSK Pre-Shared Key used to authenticate IKE connections.
IKE-Priv IKE Private Key. RSA 2048, ECDSA P-256, or ECDSA P-384
IKE-SKEYID IKE SKEYID. IKE secret used to derive IKE and IPsec ESP session keys.
IKE-SEK IKE Session Keys. Triple-DES (3 key), AES, HMAC.
IKE-DH-PRI
IKE Diffie-Hellman private component. Ephemeral Diffie-Hellman private key used in IKE.
Diffie-Hellman N = 224 bit, EC Diffie-Hellman P-256, or EC Diffie-Hellman P-384
5
SSH generates a Diffie-Hellman private key that is 2x the bit length of the longest symmetric or MAC key
negotiated.
Copyright Juniper, 2017 Version 1.10 Page 17 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
CO-PW ASCII Text used to authenticate the CO.
User-PW ASCII Text used to authenticate the User.
Table 10 – Public Keys
Name Description and usage
SSH-PUB SSH Public Host Key used to identify the host. ECDSA P-256.
SSH-DH-PUB
Diffie-Hellman public component. Ephemeral Diffie-Hellman public key used in SSH key
establishment. Diffie-Hellman (L = 2048 bit, 3072 bit, 4096 bit, 6144 bit, 7680 bit, or 8192
bit), EC Diffie-Hellman P-256, or EC Diffie-Hellman P-384
IKE-PUB IKE Public Key RSA 2048, ECDSA P-256, or ECDSA P-384
IKE-DH-PUB
Diffie-Hellman public component. Ephemeral Diffie-Hellman public key used in IKE key
establishment. Diffie-Hellman L = 2048 bit, EC Diffie-Hellman P-256, or EC Diffie-Hellman P-
384
Auth-UPub
SSH User Authentication Public Keys. Used to authenticate users to the module. ECDSA P-256
or P-384
Auth-COPub
SSH CO Authentication Public Keys. Used to authenticate CO to the module. ECDSA P-256 or
P-384
Root CA
Juniper Root CA. ECDSA P-256 or P-384 X.509 Certificate; Used to verify the validity of the
Juniper Package CA at software load.
Package CA
Package CA. ECDSA P-256 X.509 Certificate; Used to verify the validity of Juniper Images at
software load and also at runtime integrity.
Copyright Juniper, 2017 Version 1.10 Page 18 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
3 Roles, Authentication and Services
3.1 Roles and Authentication of Operators to Roles
The module supports two roles: Cryptographic Officer (CO) and User. The module supports concurrent
operators, but does not support a maintenance role and/or bypass capability. The module enforces the
separation of roles using either identity-based operator authentication.
The Cryptographic Officer role configures and monitors the module via a console or SSH connection. As
root or super-user, the Cryptographic Officer has permission to view and edit secrets within the module
The User role monitors the router via the console or SSH. The user role may not change the configuration.
3.2 Authentication Methods
The module implements two forms of Identity-Based authentication, username and password over the
Console and SSH as well as username and public key over SSH.
Password authentication: The module enforces 10-character passwords (at minimum) chosen from the
96 human readable ASCII characters. The maximum password length is 20 characters.
The module enforces a timed access mechanism as follows: For the first two failed attempts (assuming 0
time to process), no timed access is enforced. Upon the third attempt, the module enforces a 5-second
delay. Each failed attempt thereafter results in an additional 5-second delay above the previous (e.g. 4th
failed attempt = 10-second delay, 5th
failed attempt = 15-second delay, 6th
failed attempt = 20-second
delay, 7th
failed attempt = 25-second delay).
This leads to a maximum of seven (7) possible attempts in a one-minute period for each getty. The best
approach for the attacker would be to disconnect after 4 failed attempts, and wait for a new getty to be
spawned. This would allow the attacker to perform roughly 9.6 attempts per minute (576 attempts per
hour/60 mins); this would be rounded down to 9 per minute, because there is no such thing as 0.6
attempts. Thus the probability of a successful random attempt is 1/9610
, which is less than 1/1 million.
The probability of a success with multiple consecutive attempts in a one-minute period is 9/(9610
), which
is less than 1/100,000.
ECDSA signature verification: SSH public-key authentication. Processing constraints allow for a maximum
of 5.6e7 ECDSA attempts per minute. The module supports ECDSA (P-256 and P-384). The probability of a
success with multiple consecutive attempts in a one-minute period is 5.6e7/(2128
).
3.3 Services
All services implemented by the module are listed in the tables below. Table 13 – lists the access to CSPs
by each service.
Table 11 – Authenticated Services
Service Description CO User
Configure
security
Security relevant configuration x
Configure Non-security relevant configuration x
Secure Traffic IPsec protected connection (ESP) x
Status Show status x x
Zeroize Destroy all CSPs x
Copyright Juniper, 2017 Version 1.10 Page 19 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
SSH connect
Initiate SSH connection for SSH monitoring and
control (CLI)
x x
IPsec connect Initiate IPsec connection (IKE) x
Console access Console monitoring and control (CLI) x x
Remote reset Software initiated reset x
Table 12 – Unauthenticated traffic
Service Description
Local reset Hardware reset or power cycle
Traffic Traffic requiring no cryptographic services
Table 13 – CSP Access Rights within Services
Service
CSPs
DRBG_Seed
DRBG_State
SSH
PHK
SSH
DH
SSH-SEK
ESP-SEK
IKE-PSK
IKE-Priv
IKE-SKEYI
IKE-SEK
IKE-DH-PRI
CO-PW
User-PW
Configure
security
-- E GW -- -- -- RW RGW -- -- --
RW RW
Configure -- -- -- -- -- -- -- -- -- -- -- -- --
Secure
traffic
-- -- -- -- -- E -- -- -- E --
-- --
Status -- -- -- -- -- -- -- -- -- -- -- -- --
Zeroize -- Z Z -- -- -- Z Z -- -- -- Z Z
SSH connect -- E E GE GE -- -- -- -- -- -- E E
IPsec
connect
-- E -- -- -- G E E G G G
-- --
Console
access
-- -- -- -- -- -- -- -- -- -- --
E E
Remote
reset
GEZ G -- Z Z Z -- -- Z Z Z
Z Z
Local reset GEZ G -- Z Z Z -- -- Z Z Z Z Z
Traffic -- -- -- -- -- -- -- -- -- -- -- -- --
G = Generate: The module generates the CSP
R = Read: The CSP is read from the module (e.g. the CSP is output)
E = Execute: The module executes using the CSP
W = Write: The CSP is updated or written to the module
Z = Zeroize: The module zeroizes the CSP.
Copyright Juniper, 2017 Version 1.10 Page 20 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
3.4 Non-Approved Services
The following services are available in the non-Approved mode of operation. The security functions
provided by the non-Approved services are identical to the Approved counterparts with the exception of
SSH Connect (non-compliant). SSH Connect (non-compliant) supports the security functions identified in
Section 2.4 and the SSHv2 row of Table 8.
Table 14 – Authenticated Services
Service Description CO User
Configure security (non-
compliant)
Security relevant configuration x
Configure (non-
compliant)
Non-security relevant configuration x
Secure Traffic (non-
compliant)
IPsec protected connection (ESP) x
Status (non-compliant) Show status x x
Zeroize (non-compliant) Destroy all CSPs x
SSH connect (non-
compliant)
Initiate SSH connection for SSH monitoring
and control (CLI)
x x
IPsec connect (non-
compliant)
Initiate IPsec connection (IKE) x
Console access (non-
compliant)
Console monitoring and control (CLI) x x
Remote reset (non-
compliant)
Software initiated reset x
Table 15 – Unauthenticated traffic
Service Description
Local reset (non-
compliant)
Hardware reset or power cycle
Traffic (non-
compliant)
Traffic requiring no cryptographic services
Copyright Juniper, 2017 Version 1.10 Page 21 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
4 Self-tests
Each time the module is powered up it tests that the cryptographic algorithms still operate correctly and
that sensitive data have not been damaged. Power-up self–tests are available on demand by power cycling
the module.
On power up or reset, the module performs the self-tests described below. All KATs must be completed
successfully prior to any other use of cryptography by the module. If one of the KATs fails, the module
enters the Critical Failure error state.
The module performs the following power-up self-tests:
• Firmware Integrity check using ECDSA P-256 with SHA-256
• Data Plane KATs
o AES-CBC (128/192/256) Encrypt KAT
o AES-CBC (128/192/256) Decrypt KAT
o Triple-DES-CBC Encrypt KAT
o Triple-DES-CBC Decrypt KAT
o HMAC-SHA-1 KAT
o HMAC-SHA-256 KAT
o AES-GCM (128/192/256) Encrypt KAT (Note: Except on SRX5K-SPC-2-10-40, which does
not support AES GCM)
o ASE-GCM (128/192/256) Decrypt KAT (Note: Except on SRX5K-SPC-2-10-40, which does
not support AES GCM)
• Control Plane Authentec KATs
o RSA 2048 w/ SHA-256 Sign KAT
o RSA 2048 w/ SHA-256 Verify KAT
o ECDSA P-256 w/ SHA-256 Sign/Verify PCT
o Triple-DES-CBC Encrypt KAT
o Triple-DES-CBC Decrypt KAT
o HMAC-SHA-1 KAT
o HMAC-SHA-256 KAT
o HMAC-SHA-384 KAT
o AES-CBC (128/192/256) Encrypt KAT
o AES-CBC (128/192/256) Decrypt KAT
o AES-GCM (128/256) Encrypt KAT
o AES-GCM (128/256) Decrypt KAT
o KDF-IKE-V1 KAT
o KDF-IKE-V2 KAT
• OpenSSL KATs
o SP 800-90A HMAC DRBG KAT
§ Health-tests initialize, re-seed, and generate.
o ECDSA P-256 Sign/Verify PCT
o EC Diffie-Hellman P-256 KAT
§ Derivation of the expected shared secret.
o RSA 2048 w/ SHA-256 Sign KAT
o RSA 2048 w/ SHA-256 Verify KAT
o Triple-DES-CBC Encrypt KAT
o Triple-DES-CBC Decrypt KAT
Copyright Juniper, 2017 Version 1.10 Page 22 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
o HMAC-SHA-1 KAT
o HMAC-SHA-256 KAT
o HMAC-SHA-512 KAT
o SHA (256/384/512) KAT
o AES-CBC (128/192/256) Encrypt KAT
o AES-CBC (128/192/256) Decrypt KAT
o KDF-SSH KAT
• Critical Function Test
o The cryptographic module performs a verification of a limited operational environment
and verification of optional non-critical packages.
The module also performs the following conditional self-tests:
• Continuous RNG Test on the SP 800-90A HMAC-DRBG
• Continuous RNG test on the NDRNG
• Pairwise consistency test when generating ECDSA and RSA key pairs.
• Firmware Load Test (ECDSA signature verification)
Copyright Juniper, 2017 Version 1.10 Page 23 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
5 Physical Security Policy
The module’s physical embodiment is that of a multi-chip standalone device that meets Level 2 Physical
Security requirements. The module is completely enclosed in a rectangular nickel or clear zinc coated,
cold rolled steel, plated steel and brushed aluminum enclosure. There are no ventilation holes, gaps, slits,
cracks, slots, or crevices that would allow for any sort of observation of any component contained within
the cryptographic boundary. Tamper-evident seals allow the operator to tell if the enclosure has been
breached. These seals are not factory-installed and must be applied by the Cryptographic Officer. (Seals
are available for order from Juniper using part number JNPR-FIPS-TAMPER-LBLS.) The tamper-evident
seals shall be installed for the module to operate in a FIPS mode of operation.
The Cryptographic Officer is responsible for securing and having control at all times of any unused seals
and the direct control and observation of any changes to the module, such as reconfigurations where the
tamper-evident seals or security appliances are removed or installed to ensure the security of the module
is maintained during such changes and the module is returned to a FIPS Approved state.
Table 16 – Physical Security Inspection Guidelines
Physical Security
Mechanism
Recommended Frequency of
Inspection/Test
Inspection/Test Guidance Details
Tamper seals, opaque
metal enclosure.
Once per month by the
Cryptographic Officer.
Seals should be free of any tamper
evidence.
If the Cryptographic Officer observes tamper evidence, it shall be assumed that the device has been
compromised. The Cryptographic Officer shall retain control of the module and perform Zeroization of
the module's CSPs by following the steps in Section 1.3 of the Security Policy.
5.1 General Tamper Seal Placement and Application Instructions
For all seal applications, the Cryptographic Officer should observe the following instructions:
• Handle the seals with care. Do not touch the adhesive side.
• Before applying a seal, ensure the location of application is clean, dry, and clear of any residue.
• Place the seal on the module, applying firm pressure across it to ensure adhesion. Allow at least
1 hour for the adhesive to cure.
5.2 SRX5400 (13 seals)
Tamper-evident seals shall be applied to the following locations:
• Front Pane:
o Two seals, vertical, connected to the topmost (non-honeycomb) sub-pane. They extend
to the thin pane below and the honeycomb panel above.
o One seal, vertical, across the thin pane. Extends to the blank pane below and the sub-
pane above.
o Three seals, vertical, one on each “long” horizontal sub-pane. Each attaches to the sub-
pane above and the one below (or the chassis, if it’s the bottommost sub-pane). Ensure
one of the seals extends to the left sub-pane below the thin sub-pane.
• Back Pane:
o Four seals, vertical: one on each of the top four sub-panes, extending to the large chassis
plate below.
o One seal, vertical: on the horizontal screwed-in plate resting on the large central chassis.
Should extend to the chassis in both directions.
Copyright Juniper, 2017 Version 1.10 Page 24 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
o Two seals, horizontal: placed on the low side sub-panes, extending to the large central
chassis area and wrapping around to the neighboring side panes.
Figure 9 - SRX5400- Tamper-Evident Seal Locations on Front- Six Seals
Figure 10 - SRX5400- Tamper-Evident Seal Locations on Rear- Seven Seals
5.3 SRX5600 (18 seals)
Tamper-evident seals must be applied to the following locations:
• Front Pane:
o Eleven seals, vertical: one for each horizontal sub-pane (excluding the honeycomb plate
on the top and the thin sub-pane a little below), a second for the top (non-honeycomb)
sub-pane, and an extra for the bottom. The seals should attach to vertically adjacent sub-
panes. The extra on the bottom attaches to the lowermost sub-pane and wraps around,
Copyright Juniper, 2017 Version 1.10 Page 25 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
attaching to the bottom pane. It should be ensured that one of the seals spans across the
thin plate with ample extra distance on each side.
• Back Pane:
o Five seals, vertical: one on each of the upper four sub-panes, attaching to the large plate
below.
o Two seals, horizontal: one on each of the vertical side sub-panes, extending to both the
large central plate and the side panes.
Figure 11 - SRX5600- Tamper-Evident Seal Locations on Front- 11 Seals
Figure 12 - SRX5600- Tamper-Evident Seal Locations on Rear- Seven Seals
Copyright Juniper, 2017 Version 1.10 Page 26 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
5.4 SRX5800 (24 seals)
Tamper-evident seals shall be applied to the following locations:
• Front Pane:
o Fourteen seals, horizontal: one on each of the long vertical sub-panes, extending to the
neighboring two. If on an end sub-pane, seal should wrap around to the side.
o Three seals, vertical: one over each of the thin panes – two near the bottom, one near
the top of the lower half.
o Two seals, vertical: both on the console area at the top of the module, one extending to
the top and the other extending to the chassis area below.
• Back Pane:
o Five seals, horizontal: three spanning the gaps between the vertical sub-panels, and then
two more, one each on the far edges of the left and right panels. (These last two should
wrap around to the sides.)
Figure 13 - SRX5800- Tamper-Evident Seal Locations on Front- 19 Seals
Copyright Juniper, 2017 Version 1.10 Page 27 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
Figure 14 - SRX5800- Tamper-Evident Seal Locations on Rear- Five Seals
Copyright Juniper, 2017 Version 1.10 Page 28 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
6 Security Rules and Guidance
The module design corresponds to the security rules below. The term must in this context specifically
refers to a requirement for correct usage of the module in the Approved mode; all other statements
indicate a security rule implemented by the module.
1. The module clears previous authentications on power cycle.
2. When the module has not been placed in a valid role, the operator does not have access to any
cryptographic services.
3. Power up self-tests do not require any operator action.
4. Data output is inhibited during key generation, self-tests, zeroization, and error states.
5. Status information does not contain CSPs or sensitive data that if misused could lead to a compromise
of the module.
6. There are no restrictions on which keys or CSPs are zeroized by the zeroization service.
7. The module does not support a maintenance interface or role.
8. The module does not support manual key entry.
9. The module does not output intermediate key values.
10. The module requires to independent internal actions to be performed prior to outputing plaintext
CSPs.
11. The cryptographic officer must determine whether firmware being loaded is a legacy use of the
firmware load service.
12. The cryptographic officer must retain control of the module while zeroization is in process.
Copyright Juniper, 2017 Version 1.10 Page 29 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
7 References and Definitions
The following standards are referred to in this Security Policy.
Table 17 – References
Abbreviation Full Specification Name
[FIPS140-2] Security Requirements for Cryptographic Modules, May 25, 2001
[SP800-131A] Transitions: Recommendation for Transitioning the Use of Cryptographic Algorithms and
Key Lengths, January 2011
[IG] Implementation Guidance for FIPS PUB 140-2 and the Cryptographic Module Validation
Program
[135] National Institute of Standards and Technology, Recommendation for Existing
Application-Specific Key Derivation Functions, Special Publication 800-135rev1,
December 2011.
[186] National Institute of Standards and Technology, Digital Signature Standard (DSS),
Federal Information Processing Standards Publication 186-4, July 2013.
[186-2] National Institute of Standards and Technology, Digital Signature Standard (DSS),
Federal Information Processing Standards Publication 186-2, January 2000.
[197] National Institute of Standards and Technology, Advanced Encryption Standard (AES),
Federal Information Processing Standards Publication 197, November 26, 2001
[38A] National Institute of Standards and Technology, Recommendation for Block Cipher
Modes of Operation, Methods and Techniques, Special Publication 800-38A, December
2001
[38D] National Institute of Standards and Technology, Recommendation for Block Cipher
Modes of Operation: Galois/Counter Mode (GCM) and GMAC, Special Publication 800-
38D, November 2007
[38F] National Institute of Standards and Technology, Recommendation for Block Cipher
Modes of Operation: Methods for Key Wrapping, Special Publication 800-38F, December
2012
[198] National Institute of Standards and Technology, The Keyed-Hash Message
Authentication Code (HMAC), Federal Information Processing Standards Publication 198-
1, July, 2008
[180] National Institute of Standards and Technology, Secure Hash Standard, Federal
Information Processing Standards Publication 180-4, August, 2015
[67] National Institute of Standards and Technology, Recommendation for the Triple Data
Encryption Algorithm (TDEA) Block Cipher, Special Publication 800-67, May 2004
[90A] National Institute of Standards and Technology, Recommendation for Random Number
Generation Using Deterministic Random Bit Generators, Special Publication 800-90A,
June 2015.
Copyright Juniper, 2017 Version 1.10 Page 30 of 30
Juniper Networks Public Material – May be reproduced only in its original entirety (without revision).
Table 18 – Acronyms and Definitions
Acronym Definition
AES Advanced Encryption Standard
DH Diffie-Hellman
DSA Digital Signature Algorithm
ECDH Elliptic Curve Diffie-Hellman
ECDSA Elliptic Curve Digital Signature Algorithm
EMC Electromagnetic Compatibility
ESP Encapsulating Security Payload
FIPS Federal Information Processing Standard
HMAC Keyed-Hash Message Authentication Code
ICV Integrity Check Value (i.e. Tag)
IKE Internet Key Exchange Protocol
IOC Input/Output Card
IPsec Internet Protocol Security
MD5 Message Digest 5
NPC Network Processing Card
RE Routing Engine
RSA Public-key encryption technology developed by RSA Data Security, Inc.
SHA Secure Hash Algorithms
SPC Services Processing Card
SSH Secure Shell
Triple-DES Triple - Data Encryption Standard
Table 19 – Datasheets
Model Title URL
SRX5400
SRX5600
SRX5800
SRX Series Service
Gateways for service
provider, large
enterprise, and
public
sector networks.
http://www.juniper.net/assets/us/en/local/pdf/datasheets/1000254-
en.pdf