STMicroelectronics
ST33G1M2A and ST33G1M2M D01
Security Target for composition
Common Criteria for IT security evaluation
SMD_ST33G1M2AM_ST_19_002 Rev D01.1
May 2020
www.st.com
BLANK
May 2020 SMD_ST33G1M2AM_ST_19_002 Rev D01.1 3/66
ST33G1M2AM D01 platform
Security Target for composition
Common Criteria for IT security evaluation
1 Introduction (ASE_INT)
1.1 Security Target reference
1 Document identification: ST33G1M2A and ST33G1M2M D01 - SECURITY TARGET FOR
COMPOSITION.
2 Version number: Rev D01.1, issued in May 2020.
3 Registration: registered at ST Microelectronics under number
SMD_ST33G1M2AM_ST_19_002.
1.2 TOE reference
4 This document presents the Security Target (ST) of the ST33G1M2AM D01 (ST33G1M2A
and ST33G1M2M) Security Integrated Circuit (IC), designed on the ST33G platform of
STMicroelectronics, with firmware version 1.3.2.
5 The precise reference of the Target of Evaluation (TOE) is given in Section 1.4: TOE
identification and the security IC features are given in Section 1.6: TOE description.
6 A glossary of terms and abbreviations used in this document is given in Appendix A:
Glossary.
www.st.com
Contents ST33G1M2AM D01 platform Security Target for composition
4/66 SMD_ST33G1M2AM_ST_19_002
Contents
1 Introduction (ASE_INT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Security Target reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 TOE reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Context . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.4 TOE identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.5 TOE overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.6 TOE description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
1.6.1 TOE hardware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.6.2 TOE software description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.7 TOE life cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.8 TOE environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.8.1 TOE Development Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.8.2 TOE production environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.8.3 TOE operational environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2 Conformance claims (ASE_CCL, ASE_ECD) . . . . . . . . . . . . . . . . . . . . 16
2.1 Common Criteria conformance claims . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2 PP Claims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2.1 PP Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2.2 PP Additions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2.3 PP Claims rationale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3 Security problem definition (ASE_SPD) . . . . . . . . . . . . . . . . . . . . . . . . 18
3.1 Description of assets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2 Threats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.3 Organisational security policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.4 Assumptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4 Security objectives (ASE_OBJ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.1 Security objectives for the TOE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.2 Security objectives for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.3 Security objectives rationale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.3.1 TOE threat "Memory Access Violation" . . . . . . . . . . . . . . . . . . . . . . . . . 26
ST33G1M2AM D01 platform Security Target for composition Contents
SMD_ST33G1M2AM_ST_19_002 5/66
4.3.2 TOE threat "Application code confidentiality" . . . . . . . . . . . . . . . . . . . . . 26
4.3.3 TOE threat "Application data confidentiality" . . . . . . . . . . . . . . . . . . . . . 27
4.3.4 TOE threat "Application code integrity" . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.3.5 TOE threat "Application data integrity" . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.3.6 Organisational security policy "Additional Specific Security Functionality"
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.3.7 Organisational security policy "Controlled loading of the Security IC
Embedded Software" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5 Security requirements (ASE_REQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.1 Security functional requirements for the TOE . . . . . . . . . . . . . . . . . . . . . 29
5.1.1 Security Functional Requirements from the Protection Profile . . . . . . . 31
5.1.2 Additional Security Functional Requirements for the cryptographic
services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
5.1.3 Additional Security Functional Requirements for the memories protection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
5.1.4 Additional Security Functional Requirements related to the possible
availability of loading capabilities in phases 4 to 6 of the TOE life-cycle 36
5.1.5 Additional Security Functional Requirements related to the Application
Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.2 TOE security assurance requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
5.3 Refinement of the security assurance requirements . . . . . . . . . . . . . . . . 39
5.3.1 Refinement regarding functional specification (ADV_FSP) . . . . . . . . . . 40
5.3.2 Refinement regarding test coverage (ATE_COV) . . . . . . . . . . . . . . . . . 41
5.4 Security Requirements rationale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
5.4.1 Rationale for the Security Functional Requirements . . . . . . . . . . . . . . . 41
5.4.2 Additional security objectives are suitably addressed . . . . . . . . . . . . . . 44
5.4.3 Additional security requirements are consistent . . . . . . . . . . . . . . . . . . 45
5.4.4 Dependencies of Security Functional Requirements . . . . . . . . . . . . . . . 46
5.4.5 Rationale for the Assurance Requirements . . . . . . . . . . . . . . . . . . . . . . 48
6 TOE summary specification (ASE_TSS) . . . . . . . . . . . . . . . . . . . . . . . . 50
6.1 Limited fault tolerance (FRU_FLT.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
6.2 Failure with preservation of secure state (FPT_FLS.1) . . . . . . . . . . . . . . 50
6.3 Limited capabilities (FMT_LIM.1) / Test . . . . . . . . . . . . . . . . . . . . . . . . . . 50
6.4 Limited capabilities (FMT_LIM.1) / Loader . . . . . . . . . . . . . . . . . . . . . . . . 50
6.5 Limited availability (FMT_LIM.2) / Test & (FMT_LIM.2) / Loader . . . . . . . 50
6.6 Stored data confidentiality (FDP_SDC.1) . . . . . . . . . . . . . . . . . . . . . . . . . 51
Contents ST33G1M2AM D01 platform Security Target for composition
6/66 SMD_ST33G1M2AM_ST_19_002
6.7 Stored data integrity monitoring and action (FDP_SDI.2) . . . . . . . . . . . . 51
6.8 Audit storage (FAU_SAS.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6.9 Resistance to physical attack (FPT_PHP.3) . . . . . . . . . . . . . . . . . . . . . . . 51
6.10 Basic internal transfer protection (FDP_ITT.1), Basic internal TSF data
transfer protection (FPT_ITT.1) & Subset information flow control
(FDP_IFC.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
6.11 Random number generation (FCS_RNG.1) . . . . . . . . . . . . . . . . . . . . . . . 52
6.12 Cryptographic operation: EDES operation (FCS_COP.1) / EDES . . . . . . 52
6.13 Cryptographic operation: AES operation (FCS_COP.1) / AES . . . . . . . . . 52
6.14 Static attribute initialisation (FMT_MSA.3) / Memories . . . . . . . . . . . . . . . 52
6.15 Management of security attributes (FMT_MSA.1) / Memories & Specification
of management functions (FMT_SMF.1) / Memories . . . . . . . . . . . . . . . . 53
6.16 Complete access control (FDP_ACC.2) / Memories & Security attribute
based access control (FDP_ACF.1) / Memories . . . . . . . . . . . . . . . . . . . 53
6.17 Static attribute initialisation (FMT_MSA.3) / Loader . . . . . . . . . . . . . . . . . 53
6.18 Management of security attributes (FMT_MSA.1) / Loader & Specification of
management functions (FMT_SMF.1) / Loader . . . . . . . . . . . . . . . . . . . . 53
6.19 Subset access control (FDP_ACC.1) / Loader, Security attribute based
access control (FDP_ACF.1) / Loader, Security roles (FMT_SMR.1) / Loader
& Timing of identification (FIA_UID.1) / Loader . . . . . . . . . . . . . . . . . . . . 53
6.20 Import of user data without security attributes (FDP_ITC.1) / Loader . . . 53
6.21 Subset access control (FDP_ACC.1) / APPLI_FWL & Security attribute
based access control (FDP_ACF.1) / APPLI_FWL . . . . . . . . . . . . . . . . . 54
6.22 Static attribute initialisation (FMT_MSA.3) / APPLI_FWL . . . . . . . . . . . . . . 54
7 Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
8 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Appendix A Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
A.1 Terms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
A.2 Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
ST33G1M2AM D01 platform Security Target for composition List of tables
SMD_ST33G1M2AM_ST_19_002 7/66
List of tables
Table 1. TOE components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 2. Derivative devices configuration possibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Table 3. Composite product life cycle phases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 4. Summary of security aspects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 5. Summary of security objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 6. Security Objectives versus Assumptions, Threats or Policies . . . . . . . . . . . . . . . . . . . . . . 25
Table 7. Summary of functional security requirements for the TOE . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 8. FCS_COP.1 iterations (cryptographic operations) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 9. TOE security assurance requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Table 10. Impact of EAL5 selection on BSI-CC-PP-0084-2014 refinements . . . . . . . . . . . . . . . . . . . 40
Table 11. Security Requirements versus Security Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 12. Dependencies of security functional requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 13. TOE components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Table 14. Guidance documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Table 15. Sites list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 16. Common Criteria. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Table 17. Protection Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Table 18. Other standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Table 19. List of abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
List of figures ST33G1M2AM D01 platform Security Target for composition
8/66 SMD_ST33G1M2AM_ST_19_002
List of figures
Figure 1. ST33G1M2AM D01 platform block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ST33G1M2AM D01 platform Security Target for composition
SMD_ST33G1M2AM_ST_19_002 9/66
1.3 Context
7 The Target of Evaluation (TOE) referred to in Section 1.4: TOE identification, is evaluated
under the French IT Security Evaluation and Certification Scheme and is developed by the
Secure Microcontrollers Division of STMicroelectronics (ST).
8 The assurance level of the performed Common Criteria (CC) IT Security Evaluation is EAL5
augmented by ALC_DVS.2 and AVA_VAN.5.
9 The intent of this Security Target is to specify the Security Functional Requirements (SFRs)
and Security Assurance Requirements (SARs) applicable to the TOE security ICs, and to
summarise their chosen TSF services and assurance measures.
10 This ST claims to be an instantiation of the "Eurosmart - Security IC Platform Protection
Profile with Augmentation Packages" (PP) registered and certified under the reference BSI-
CC-PP-0084-2014 in the German IT Security Evaluation and Certification Scheme, with the
following augmentations:
• Addition #1: “Support of Cipher Schemes” from AUG
• Addition #4: “Area based Memory Access Control” from AUG
• Additions specific to this Security Target.
The original text of this PP is typeset as indicated here, its augmentations from AUG as
indicated here, when they are reproduced in this document.
This ST also instantiates the following package from the above mentioned PP:
• Loader dedicated for usage in secured environment only.
11 Extensions introduced in this ST to the SFRs of the Protection Profile (PP) are exclusively
drawn from the Common Criteria part 2 standard SFRs.
12 This ST makes various refinements to the above mentioned PP and AUG. They are all
properly identified in the text typeset as indicated here. The original text of the PP is
repeated as scarcely as possible in this document for reading convenience. All PP
identifiers have been however prefixed by their respective origin label: BSI for BSI-CC-PP-
0084-2014, AUG1 for Addition #1 of AUG and AUG4 for Addition #4 of AUG.
ST33G1M2AM D01 platform Security Target for composition
10/66 SMD_ST33G1M2AM_ST_19_002
1.4 TOE identification
13 The Target of Evaluation (TOE) is the ST33G1M2AM D01 platform.
14 “ST33G1M2AM D01” completely identifies the TOE including its components listed in
Table 1: TOE components, its guidance documentation detailed in Table 14: Guidance
documentation, and its development and production sites indicated in Table 15: Sites list.
15 D01 is the version of the evaluated platform. Any change in the TOE components, the
guidance documentation and the list of sites leads to a new version of the evaluated
platform, thus a new TOE.
16 The IC maskset name is the product hardware identification.
The IC version is updated for any change in hardware (i.e. part of the layers of the maskset)
or in the OST software.
17 All along the product life, the marking on the die, a set of accessible registers and a set of
specific instructions allow the customer to check the product information, providing the
identification elements, as listed in Table 1: TOE components, and the configuration
elements as detailed in the Data Sheet, referenced in Table 14: Guidance documentation.
1.5 TOE overview
18 The TOE is a serial access Smartcard IC designed for secure mobile applications, based on
the most recent generation of ARM® processors for embedded secure systems. Its
SecurCore® SC300™ 32-bit RISC core is built on the Cortex™ M3 core with additional
security features to help to protect against advanced forms of attacks.
19 The TOE offers a high-speed User Flash memory, an internally generated clock, an MPU,
an internal true random number generator (TRNG) and hardware accelerators for advanced
cryptographic functions.
20 Different derivative devices may be configured depending on the customer needs:
• either by ST during the manufacturing or packaging process,
• or by the customer during the packaging, or composite product integration, or
personnalisation process.
21 They all share the same hardware design and the same maskset (denoted by the Master
identification number).
22 The configuration of the derivative devices can impact the available NVM memory size, and
the operational temperature range, as detailed here below:
Table 1. TOE components
IC Maskset name IC version
Master identification
number (1) Firmware version OST version
K8H0A(2)
G
00F2h (ST33G1M2A0)
1.3.2 2.2
00F3h (ST33G1M2M0)
1. Part of the product information.
2. This maskset K8H0A rev G corresponds to product line K8M0.
ST33G1M2AM D01 platform Security Target for composition
SMD_ST33G1M2AM_ST_19_002 11/66
23 All combinations of different features values are possible and covered by this certification.
All possible configurations can vary under a unique IC, and without impact on security.
24 The Master identification number is unique for all product configurations.
Each derivative device has a specific Child product identification number, also part of the
product information, and specified in the Data Sheet and in the Firmware User Manual,
referenced in Table 14.
25 The rest of this document applies to all possible configurations of the TOE, except when a
restriction is mentioned. For easier reading, the restrictions are typeset as indicated here.
26 In a few words, the ST33G1M2AM D01, offers a unique combination of high performances
and very powerful features for high level security:
• Die integrity,
• Monitoring of environmental parameters,
• Protection mechanisms against faults,
• AIS20/AIS31 class PTG.2 compliant True Random Number Generator,
• Memory Protection Unit,
• ISO/IEC 13239 CRC calculation block,
• Hardware Security Enhanced DES accelerator,
• AES accelerator (HW-AES),
• Library Protection Unit,
• Next Step Cryptography accelerator (NESCRYPT).
1.6 TOE description
1.6.1 TOE hardware description
27 The TOE features hardware accelerators for advanced cryptographic functions, with built-in
countermeasures against side channel attacks.
The AES (Advanced Encryption Standard) accelerator provides a high-performance
implementation of AES-128, AES-192 and AES-256 algorithms. It can operate in Electronic
CodeBook (ECB) or Cipher Block Chaining (CBC) modes.
28 The 3-key triple DES(a)
accelerator (EDES+) supports efficiently the Triple Data Encryption
Standard (TDES [2]), enabling Electronic Code Book (ECB) and Cipher Block Chaining
(CBC) modes, and DES computation.
Note that a triple DES can be performed by a triple DES computation or by 3 single DES
computations.
Table 2. Derivative devices configuration possibilities
Features Possible values
NVM size Selectable by 128 Kbytes granularity from 1280 Kbytes to 384 Kbytes
Operational temperature range See Data Sheet, referenced in Table 14: Guidance documentation
a. Note that DES and triple DES with two keys are no longer recommended as encryption functions. Hence, Security IC
Embedded Software may need to use triple DES with three keys to achieve a suitable strength.
ST33G1M2AM D01 platform Security Target for composition
12/66 SMD_ST33G1M2AM_ST_19_002
29 The NESCRYPT crypto-processor allows fast and secure implementation of the most
popular public key cryptosystems with a high level of performance ([4], [6], [8],[9], [10], [11]).
30 As randomness is a key stone in many applications, the ST33G1M2AM D01 features a
highly reliable True Random Number Generator (TRNG), compliant with PTG.2 Class of
AIS20/AIS31 [1] and directly accessible thru dedicated registers.
31 This device includes the ARM® SecurCore® SC300™ memory protection unit (MPU),
which enables the user to define its own region organization with specific protection and
access permissions. The MPU can be used to enforce various protection models, ranging
from a basic code dump prevention model up to a full application confinement model.
32 The TOE offers 3 communication channels to the external world: a serial communication
interface fully compatible with the ISO/IEC 7816-3 standard, a single-wire protocol (SWP)
interface for communication with a near-field communication (NFC) router in SIM/NFC
applications, and an alternative and exclusive SPI Slave interface for communication in non-
SIM applications.
33 The detailed features of this TOE are described in the Data Sheet and in the Cortex SC300
Technical Reference Manual, referenced in Table 14.
34 Figure 1 provides an overview of the ST33G1M2AM D01 platform.
Figure 1. ST33G1M2AM D01 platform block diagram
1.6.2 TOE software description
35 The OST ROM contains a Dedicated Software which provides full test capabilities
(operating system for test, called "OST"), not accessible by the Security IC Embedded
Software (ES), after TOE delivery.
36 The System ROM and ST NVM of the TOE contain a Dedicated Software which provides a
very reduced set of commands for final test (operating system for final test, called "FTOS"),
ST33G1M2AM D01 platform Security Target for composition
SMD_ST33G1M2AM_ST_19_002 13/66
not intended for the Security IC Embedded Software (ES) usage, and not available in User
configuration.
37 The System ROM and ST NVM of the TOE contain a Dedicated Support Software called
Secure Flash Loader, enabling to securely and efficiently download the Security IC
Embedded Software (ES) into the NVM. It also allows the evaluator to load software into the
TOE for test purpose. The Secure Flash Loader is not available in User configuration.
38 The System ROM and ST NVM of the TOE contain a Dedicated Support Software, which
provides low-level functions (called Flash Drivers), enabling the Security IC Embedded
Software (ES) to modify and manage the NVM contents. The Flash Drivers are available all
through the product life-cycle.
39 The Security IC Embedded Software (ES) is in User NVM.
The ES is not part of the TOE and is out of scope of the evaluation.
40 The user guidance documentation, part of the TOE, consists of:
• the product Data Sheet and die description,
• the product family Security Guidance,
• the AIS31 user manuals,
• the Cortex M3 SC300 Technical Reference Manuals,
• the Firmware user manual,
• the Flash loader installation guide.
41 The complete list of guidance documents is detailed in Table 14.
1.7 TOE life cycle
42 This Security Target is fully conform to the claimed PP. In the following, just a summary and
some useful explanations are given. For complete details on the TOE life cycle, please refer
to the Eurosmart - Security IC Platform Protection Profile with Augmentation Packages
(BSI-CC-PP-0084-2014), section 1.2.3.
43 The composite product life cycle is decomposed into 7 phases. Each of these phases has
the very same boundaries as those defined in the claimed protection profile.
44 The life cycle phases are summarized in Table 3.
45 The sites potentially involved in the TOE life cycle are listed in Table 15.
46 The limit of the evaluation corresponds to phases 2, 3 and optionally 4, including the
delivery and verification procedures of phase 1, and the TOE delivery either to the IC
packaging manufacturer or to the composite product integrator; procedures corresponding
to phases 1, 5, 6 and 7 are outside the scope of this evaluation.
47 In the following, the term "Composite product manufacturing" is uniquely used to indicate
phases 1, optionally 4, 5 and 6 all together.
This ST also uses the term "Composite product manufacturer" which includes all roles
responsible of the TOE during phases 1, optionally 4, 5 and 6.
48 The TOE is delivered after Phase 3 in form of wafers or after Phase 4 in packaged form,
depending on the customer’s order.
ST33G1M2AM D01 platform Security Target for composition
14/66 SMD_ST33G1M2AM_ST_19_002
49 In the following, the term "TOE delivery" is uniquely used to indicate:
• after Phase 3 (or before Phase 4) if the TOE is delivered in form of wafers or sawn
wafers (dice) or
• after Phase 4 (or before Phase 5) if the TOE is delivered in form of packaged products.
50 The TOE is delivered in Admin (aka Issuer) or User configuration.
1.8 TOE environment
51 Considering the TOE, three types of environments are defined:
• Development environment corresponding to phase 2,
• Production environment corresponding to phase 3 and optionally 4,
• Operational environment, including phase 1 and from phase 4 or 5 to phase 7.
1.8.1 TOE Development Environment
52 To ensure security, the environment in which the development takes place is secured with
controllable accesses having traceability. Furthermore, all authorised personnel involved
fully understand the importance and the strict implementation of defined security
procedures.
53 The development begins with the TOE's specification. All parties in contact with sensitive
information are required to abide by Non-Disclosure Agreements.
54 Design and development of the IC then follows, together with the dedicated and engineering
software and tools development. The engineers use secure computer systems (preventing
unauthorised access) to make their developments, simulations, verifications and generation
of the TOE's databases. Sensitive documents, files and tools, databases on tapes, and
Table 3. Composite product life cycle phases
Phase Name Description
1
Security IC embedded
software development
security IC embedded software development
specification of IC pre-personalization requirements
2
IC development IC design
IC dedicated software development
3
IC manufacturing and
testing
integration and photomask fabrication
IC manufacturing
IC testing
IC pre-personalisation
4
IC packaging security IC packaging (and testing)
pre-personalisation if necessary
5
Security IC product
finishing process
composite product finishing process
composite product testing
6
Security IC
personalisation
composite product personalisation
composite product testing
7 Security IC end usage composite product usage by its issuers and consumers
ST33G1M2AM D01 platform Security Target for composition
SMD_ST33G1M2AM_ST_19_002 15/66
printed circuit layout information are stored in appropriate locked cupboards/safe. Of
paramount importance also is the disposal of unwanted data (complete electronic erasures)
and documents (e.g. shredding).
55 The development centres possibly involved in the development of the TOE are denoted by
the activity “DEV” in Table 15.
1.8.2 TOE production environment
56 Reticules and photomasks are generated from the verified IC databases; the former are
used in the silicon Wafer-fab processing. As reticules and photomasks are generated off-
site, they are transported and worked on in a secure environment. During the transfer of
sensitive data electronically, procedures are established to ensure that the data arrive only
at the destination and are not accessible at intermediate stages (e.g. stored on a buffer
server where system administrators make backup copies).
57 The authorized sub-contractors potentially involved in the TOE mask manufacturing are
denoted by the activity “MASK” in Table 15.
58 As high volumes of product commonly go through such environments, adequate control
procedures are necessary to account for all product at all stages of production.
59 Production starts within the Wafer-fab; here the silicon wafers undergo the diffusion
processing. Computer tracking at wafer level throughout the process is commonplace. The
wafers are then taken into the test area. Testing and pre-personalization of each TOE
occurs to assure conformance with the device specification.
60 The authorized front-end plant possibly involved in the manufacturing of the TOE are
denoted by the activity “FE” in Table 15.
61 The authorized EWS plant potentially involved in the testing of the TOE are denoted by the
activity “EWS” in Table 15.
62 Wafers are then scribed and broken such as to separate the functional from the non-
functional ICs. The latter is discarded in a controlled accountable manner. The good ICs are
then packaged in phase 4, in a back-end plant. When testing, programming or deliveries are
done offsite, ICs are transported and worked on in a secure environment with accountability
and traceability of all (good and bad) products.
63 When the product is delivered after phase 4, the authorized back-end plants possibly
involved in the packaging of the TOE are denoted by the activity “BE” in Table 15.
64 All sites denoted by the activity “WHS” in Table 15 can be involved for the logistics.
1.8.3 TOE operational environment
65 A TOE operational environment is the environment of phases 1, optionally 4, then 5 to 7.
66 At phases 1, 4, 5 and 6, the TOE operational environment is a controlled environment.
67 End-user environments (phase 7): composite products are used in a wide range of
applications to assure authorised conditional access. Examples of such are pay-TV, banking
cards, brand protection, portable communication SIM cards, health cards, transportation
cards, access management, identity and passport cards. The end-user environment
therefore covers a wide range of very different functions, thus making it difficult to avoid and
monitor any abuse of the TOE.
Conformance claims (ASE_CCL, ASE_ECD) ST33G1M2AM D01 platform Security Target for com-
16/66 SMD_ST33G1M2AM_ST_19_002
2 Conformance claims (ASE_CCL, ASE_ECD)
2.1 Common Criteria conformance claims
68 The ST33G1M2AM D01 platform Security Target claims to be conformant to the Common
Criteria version 3.1 revision 5.
69 Furthermore it claims to be CC Part 2 (CCMB-2017-04-002 R5) extended and CC Part 3
(CCMB-2017-04-003 R5) conformant.
70 The extended Security Functional Requirements are those defined in the Eurosmart -
Security IC Platform Protection Profile with Augmentation Packages (BSI-CC-PP-0084-
2014):
• FCS_RNG Generation of random numbers,
• FMT_LIM Limited capabilities and availability,
• FAU_SAS Audit data storage,
• FDP_SDC Stored data confidentiality.
The reader can find their certified definitions in the text of the "BSI-CC-PP-0084-2014"
Protection Profile.
71 The assurance level for the ST33G1M2AM D01 platform Security Target is EAL5
augmented by ALC_DVS.2 and AVA_VAN.5.
2.2 PP Claims
2.2.1 PP Reference
72 The ST33G1M2AM D01 platform Security Target claims strict conformance to the
Eurosmart - Security IC Platform Protection Profile with Augmentation Packages (BSI-CC-
PP-0084-2014), for the part of the TOE covered by this PP (Security IC), as required by this
Protection Profile.
2.2.2 PP Additions
73 The main additions operated on the BSI-CC-PP-0084-2014 are:
• Addition #4: “Area based Memory Access Control” from AUG,
• Addition #1: “Support of Cipher Schemes” from AUG,
• Specific additions for the Secure Flash Loader,
• Specific additions for the LPU,
• Refinement of assurance requirements.
74 All refinements are indicated with type setting text as indicated here, original text from the
BSI-CC-PP-0084-2014 being typeset as indicated here. Text originating in AUG is typeset
as indicated here.
75 The security environment additions relative to the PP are summarized in Table 4.
76 The additional security objectives relative to the PP are summarized in Table 5.
77 A simplified presentation of the TOE Security Policy (TSP) is added.
ST33G1M2AM D01 platform Security Target for composition Conformance claims (ASE_CCL,
SMD_ST33G1M2AM_ST_19_002 17/66
78 The additional SFRs for the TOE relative to the PP are summarized in Table 7.
79 The additional SARs relative to the PP are summarized in Table 9.
2.2.3 PP Claims rationale
80 The differences between this Security Target security objectives and requirements and
those of BSI-CC-PP-0084-2014, to which conformance is claimed, have been identified and
justified in Section 4 and in Section 5. They have been recalled in the previous section.
81 In the following, the statements of the security problem definition, the security objectives,
and the security requirements are consistent with those of the BSI-CC-PP-0084-2014.
82 The security problem definition presented in Section 3, clearly shows the additions to the
security problem statement of the PP.
83 The security objectives rationale presented in Section 4.3 clearly identifies modifications
and additions made to the rationale presented in the BSI-CC-PP-0084-2014.
84 Similarly, the security requirements rationale presented in Section 5.4 has been updated
with respect to the protection profile.
85 All PP requirements have been shown to be satisfied in the extended set of requirements
whose completeness, consistency and soundness have been argued in the rationale
sections of the present document.
Security problem definition (ASE_SPD) ST33G1M2AM D01 platform Security Target for composi-
18/66 SMD_ST33G1M2AM_ST_19_002
3 Security problem definition (ASE_SPD)
86 This section describes the security aspects of the environment in which the TOE is intended
to be used and addresses the description of the assets to be protected, the threats, the
organisational security policies and the assumptions.
87 Note that the origin of each security aspect is clearly identified in the prefix of its label. Most
of these security aspects can therefore be easily found in the Eurosmart - Security IC
Platform Protection Profile with Augmentation Packages (BSI-CC-PP-0084-2014), section
3. Only those originating in AUG, and the ones introduced in this Security Target, are
detailed in the following sections.
88 A summary of all these security aspects and their respective conditions is provided in
Table 4.
Table 4. Summary of security aspects
Label Title
TOE
threats
BSI.T.Leak-Inherent Inherent Information Leakage
BSI.T.Phys-Probing Physical Probing
BSI.T.Malfunction Malfunction due to Environmental Stress
BSI.T.Phys-Manipulation Physical Manipulation
BSI.T.Leak-Forced Forced Information Leakage
BSI.T.Abuse-Func Abuse of Functionality
BSI.T.RND Deficiency of Random Numbers
AUG4.T.Mem-Access Memory Access Violation
T.Confid-Applic-Code Application code confidentiality
T.Confid-Applic-Data Application data confidentiality
T.Integ-Applic-Code Application code integrity
T.Integ-Applic-Data Application data integrity
OSPs
BSI.P.Process-TOE Protection during TOE Development and Production
BSI.P.Lim-Block-Loader Limiting and blocking the loader functionality
AUG1.P.Add-Functions Additional Specific Security Functionality (Cipher Scheme
Support)
P.Controlled-ES-Loading Controlled loading of the Security IC Embedded Software
Assumptions
BSI.A.Process-Sec-IC Protection during Packaging, Finishing and Personalisation
BSI.A.Resp-Appl Treatment of User Data
ST33G1M2AM D01 platform Security Target for composition Security problem definition
SMD_ST33G1M2AM_ST_19_002 19/66
3.1 Description of assets
89 The assets (related to standard functionality) to be protected are
• the User Data,
• the Security IC Embedded Software, stored and in operation
• the security services provided by the TOE for the Security IC Embedded Software.
90 The user (consumer) of the TOE places value upon the assets related to high-level security
concerns:
SC1 integrity of User Data and of the Security IC Embedded Software (while being
executed/processed and while being stored in the TOE's memories),
SC2 confidentiality of User Data and of the Security IC Embedded Software (while being
processed and while being stored in the TOE's memories)
SC3 correct operation of the security services provided by the TOE for the Security IC
Embedded Software.
91 According to the Protection Profile there is the following high-level security concern related
to security service:
SC4 deficiency of random numbers.
92 To be able to protect these assets the TOE shall protect its security functionality. Therefore
critical information about the TOE shall be protected. Critical information includes:
• logical design data, physical design data, IC Dedicated Software, and configuration
data,
• Initialisation Data and Pre-personalisation Data, specific development aids, test and
characterisation related data, material for software development support, and
photomasks.
Such information and the ability to perform manipulations assist in threatening the above
assets.
93 The information and material produced and/or processed by the TOE manufacturer in the
TOE development and production environment (Phases 2 up to TOE delivery) can be
grouped as follows:
• logical design data,
• physical design data,
• IC Dedicated Software, Security IC Embedded Software, Initialisation Data and pre-
personalisation Data,
• specific development aids,
• test and characterisation related data,
• material for software development support, and
• photomasks and products in any form
as long as they are generated, stored, or processed by the TOE manufacturer.
94 Application note:
The TOE providing a functionality for Security IC Embedded Software secure loading into
NVM, the ES is considered as User Data being stored in the TOE’s memories at this step,
and the Protection Profile security concerns are extended accordingly.
Security problem definition (ASE_SPD) ST33G1M2AM D01 platform Security Target for composi-
20/66 SMD_ST33G1M2AM_ST_19_002
3.2 Threats
95 The threats are described in the BSI-CC-PP-0084-2014, section 3.2.
Only those originating in AUG and those introduced in this Security Target are detailed in
the following section.
96
BSI.T.Leak-Inherent Inherent Information Leakage
BSI.T.Phys-Probing Physical Probing
BSI.T.Malfunction Malfunction due to Environmental Stress
BSI.T.Phys-
Manipulation
Physical Manipulation
BSI.T.Leak-Forced Forced Information Leakage
BSI.T.Abuse-Func Abuse of Functionality
BSI.T.RND Deficiency of Random Numbers
AUG4.T.Mem-Access Memory Access Violation:
Parts of the Security IC Embedded Software may cause security
violations by accidentally or deliberately accessing restricted data
(which may include code). Any restrictions are defined by the
security policy of the specific application context and must be
implemented by the Security IC Embedded Software.
Clarification: This threat does not address the proper definition and
management of the security rules implemented by the Security IC
Embedded Software, this being a software design and correctness
issue. This threat addresses the reliability of the abstract machine
targeted by the software implementation. To avert the threat, the set
of access rules provided by this TOE should be undefeated if
operated according to the provided guidance. The threat is not
realized if the Security IC Embedded Software is designed or
implemented to grant access to restricted information. It is realized
if an implemented access denial is granted under unexpected
conditions or if the execution machinery does not effectively control
a controlled access.
Here the attacker is expected to (i) take advantage of flaws in the
design and/or the implementation of the TOE memory access rules
(refer to BSI.T.Abuse-Func but for functions available after TOE
delivery), (ii) introduce flaws by forcing operational conditions (refer
to BSI.T.Malfunction) and/or by physical manipulation (refer to
BSI.T.Phys-Manipulation). This attacker is expected to have a high
level potential of attack.
T.Confid-Applic-Code Application code confidentiality:
A sensitive application code may need to be protected against
unauthorized disclosure. This relates to attacks at runtime to gain
read or compare access to memory area where the sensitive
application executable code is stored.
The attacker executes an application to disclose code belonging to
the sensitive application.
ST33G1M2AM D01 platform Security Target for composition Security problem definition
SMD_ST33G1M2AM_ST_19_002 21/66
3.3 Organisational security policies
97 The TOE provides specific security functionality that can be used by the Security IC
Embedded Software. In the following specific security functionality is listed which is not
derived from threats identified for the TOE’s environment because it can only be decided in
the context of the Security IC application, against which threats the Security IC Embedded
Software will use the specific security functionality.
98 ST applies the Protection policy during TOE Development and Production (BSI.P.Process-
TOE) as specified below.
99 BSI.P.Lim-Block-Loader is dedicated to the Secure Flash Loader, and described in the BSI-
CC-PP-0084-2014 package “Loader dedicated for usage in secured environment only”.
100 ST applies the Additional Specific Security Functionality policy (AUG1.P.Add-Functions) as
specified below.
101 New Organisational Security Policies (OSPs) are defined here below:
102 P.Controlled-ES-Loading is related to the capability provided by the TOE to load Security IC
Embedded Software into the NVM after TOE delivery, in a controlled manner, during
composite product manufacturing. The use of this capability is optional, and depends on the
customer’s production organization.
T.Confid-Applic-Data Application data confidentiality:
A sensitive application data may need to be protected against
unauthorized disclosure. This relates to attacks at runtime to gain
read or compare access to the sensitive application data by another
application.
For example, the attacker executes an application that tries to read
data belonging to the sensitive application.
T.Integ-Applic-Code Application code integrity:
A sensitive application code may need to be protected against
unauthorized modification. This relates to attacks at runtime to gain
write access to memory area where the sensitive application
executable code is stored.
The attacker executes an application that tries to alter (part of) the
sensitive application code.
T.Integ-Applic-Data Application data integrity:
A sensitive application data may need to be protected against
unauthorized modification. This relates to attacks at runtime to gain
write access to the sensitive application data by another
application.
The attacker executes an application that tries to alter (part of) the
sensitive application data.
BSI.P.Process-TOE Identification during TOE Development and Production:
An accurate identification is established for the TOE. This
requires that each instantiation of the TOE carries this unique
identification.
Security problem definition (ASE_SPD) ST33G1M2AM D01 platform Security Target for composi-
22/66 SMD_ST33G1M2AM_ST_19_002
3.4 Assumptions
103 The following assumptions are described in the BSI-CC-PP-0084-2014, section 3.4.
BSI.P.Lim-Block-Loader Limiting and blocking the loader functionality:
The composite manufacturer uses the Loader for loading of
Security IC Embedded Software, user data of the Composite
Product or IC Dedicated Support Software in charge of the IC
Manufacturer. He limits the capability and blocks the availability
of the Loader in order to protect stored data from disclosure and
manipulation.
AUG1.P.Add-Functions Additional Specific Security Functionality:
The TOE shall provide the following specific security functionality
to the Security IC Embedded Software:
– Triple Data Encryption Standard (TDES),
– Advanced Encryption Standard (AES),
Note that DES and triple DES with two keys are no longer
recommended as encryption functions. Hence, Security IC Embedded
Software may need to use triple DES with three keys to achieve a
suitable strength.
P.Controlled-ES-Loading Controlled loading of the Security IC Embedded Software:
The TOE shall provide the capability to import the Security IC
Embedded Software into the NVM, in a controlled manner, either
before TOE delivery, under ST authority, either after TOE
delivery, under the composite product manufacturer authority.
This capability is not available in User configuration.
BSI.A.Process-Sec-IC Protection during Packaging, Finishing and Personalisation
BSI.A.Resp-Appl Treatment of User Data of the Composite TOE
ST33G1M2AM D01 platform Security Target for composition Security objectives (ASE_OBJ)
SMD_ST33G1M2AM_ST_19_002 23/66
4 Security objectives (ASE_OBJ)
104 The security objectives of the TOE cover principally the following aspects:
• integrity and confidentiality of assets,
• protection of the TOE and associated documentation during development and
production phases,
• provide random numbers,
• provide cryptographic support and access control functionality.
105 A summary of all security objectives is provided in Table 5.
106 Note that the origin of each objective is clearly identified in the prefix of its label.
Most of these security aspects can therefore be easily found in the BSI-CC-PP-0084-2014,
sections 4.1 and 7.3. Only those originating in AUG, and the ones introduced in this Security
Target, are detailed in the following sections.
4.1 Security objectives for the TOE
Table 5. Summary of security objectives
Label Title
TOE
BSI.O.Leak-Inherent Protection against Inherent Information Leakage
BSI.O.Phys-Probing Protection against Physical Probing
BSI.O.Malfunction Protection against Malfunctions
BSI.O.Phys-Manipulation Protection against Physical Manipulation
BSI.O.Leak-Forced Protection against Forced Information Leakage
BSI.O.Abuse-Func Protection against Abuse of Functionality
BSI.O.Identification TOE Identification
BSI.O.RND Random Numbers
BSI.O.Cap-Avail-Loader Capability and Availability of the Loader
AUG1.O.Add-Functions Additional Specific Security Functionality
AUG4.O.Mem-Access Dynamic Area based Memory Access Control
O.Controlled-ES-Loading Controlled loading of the Security IC Embedded
Software
O.Firewall Application firewall
Environments
BSI.OE.Resp-Appl Treatment of User Data of the Composite TOE
BSI.OE.Process-Sec-IC Protection during composite product manufacturing
BSI.OE.Lim-Block-Loader Limitation of capability and blocking the Loader
BSI.O.Leak-Inherent Protection against Inherent Information Leakage
Security objectives (ASE_OBJ) ST33G1M2AM D01 platform Security Target for composition
24/66 SMD_ST33G1M2AM_ST_19_002
4.2 Security objectives for the environment
107 Security Objectives for the Security IC Embedded Software development environment
(phase 1):
BSI.O.Phys-Probing Protection against Physical Probing
BSI.O.Malfunction Protection against Malfunctions
BSI.O.Phys-Manipulation Protection against Physical Manipulation
BSI.O.Leak-Forced Protection against Forced Information Leakage
BSI.O.Abuse-Func Protection against Abuse of Functionality
BSI.O.Identification TOE Identification
BSI.O.RND Random Numbers
BSI.O.Cap-Avail-Loader Capability and Availability of the Loader
AUG1.O.Add-Functions Additional Specific Security Functionality:
The TOE must provide the following specific security
functionality to the Security IC Embedded Software:
– Triple Data Encryption Standard (TDES),
– Advanced Encryption Standard (AES).
AUG4.O.Mem-Access Dynamic Area based Memory Access Control:
The TOE must provide the Security IC Embedded Software
with the capability to define dynamic memory segmentation
and protection. The TOE must then enforce the defined
access rules so that access of software to memory areas is
controlled as required, for example, in a multi-application
environment.
O.Controlled-ES-Loading Controlled loading of the Security IC Embedded Software:
The TOE must provide the capability to load the Security IC
Embedded Software into the NVM, either before TOE delivery,
under ST authority, either after TOE delivery, under the
composite product manufacturer authority. The TOE must
restrict the access to these features. The TOE must provide
control means to check the integrity of the loaded user data.
This capability is not available in User configuration.
O.Firewall Application firewall:
The TOE provides a service to ensure isolation of data and
code between a Protected Application and the other
applications. Another application shall not read, write,
compare any piece of data or code belonging to the Protected
Application.
BSI.OE.Resp-Appl Treatment of User Data of the Composite TOE
ST33G1M2AM D01 platform Security Target for composition Security objectives (ASE_OBJ)
SMD_ST33G1M2AM_ST_19_002 25/66
108 Security Objectives for the operational Environment (phase 4 up to 6):
4.3 Security objectives rationale
109 The main line of this rationale is that the inclusion of all the security objectives of the BSI-
CC-PP-0084-2014 protection profile, together with those in AUG, and those introduced in
this ST, guarantees that all the security environment aspects identified in Section 3 are
addressed by the security objectives stated in this chapter.
110 Thus, it is necessary to show that:
• security environment aspects from AUG and from this ST, are addressed by security
objectives stated in this chapter,
• security objectives from AUG and from this ST, are suitable (i.e. they address security
environment aspects),
• security objectives from AUG and from this ST, are consistent with the other security
objectives stated in this chapter (i.e. no contradictions).
111 The selected augmentations from AUG introduce the following security environment
aspects:
• TOE threat "Memory Access Violation, (AUG4.T.Mem-Access)",
• organisational security policy "Additional Specific Security Functionality, (AUG1.P.Add-
Functions)".
112 The augmentation made in this ST introduces the following security environment aspects:
• TOE threats "Application code confidentiality, (T.Confid-Applic-Code)", "Application
data confidentiality, (T.Confid-Applic-Data)", "Application code integrity, (T.Integ-Applic-
Code)", and "Application data integrity, (T.Integ-Applic-Data)".
• organisational security policy "Controlled loading of the Security IC Embedded
Software, (P.Controlled-ES-Loading)".
113 The justification of the additional policies, and additional threats provided in the next
subsections shows that they do not contradict to the rationale already given in the protection
profile BSI-CC-PP-0084-2014 for the assumptions, policy and threats defined there.
BSI.OE.Process-Sec-IC Protection during composite product manufacturing
BSI.OE.Lim-Block-Loader Limitation of capability and blocking the Loader
Table 6. Security Objectives versus Assumptions, Threats or Policies
Assumption, Threat or
Organisational Security Policy
Security Objective Notes
BSI.A.Resp-Appl BSI.OE.Resp-Appl Phase 1
BSI.P.Process-TOE BSI.O.Identification Phase 2-3
optional
Phase 4
BSI.P.Lim-Block-Loader BSI.O.Cap-Avail-Loader
BSI.OE.Lim-Block-Loader
Phase 5-6
optional
Phase 4
Security objectives (ASE_OBJ) ST33G1M2AM D01 platform Security Target for composition
26/66 SMD_ST33G1M2AM_ST_19_002
4.3.1 TOE threat "Memory Access Violation"
114 The justification related to the threat “Memory Access Violation, (AUG4.T.Mem-Access)” is
as follows:
115 According to AUG4.O.Mem-Access the TOE must enforce the dynamic memory
segmentation and protection so that access of software to memory areas is controlled.
Any restrictions are to be defined by the Security IC Embedded Software. Thereby security
violations caused by accidental or deliberate access to restricted data (which may include
code) can be prevented (refer to AUG4.T.Mem-Access). The threat AUG4.T.Mem-Access is
therefore removed if the objective is met.
116 The added objective for the TOE AUG4.O.Mem-Access does not introduce any
contradiction in the security objectives for the TOE.
4.3.2 TOE threat "Application code confidentiality"
117 The justification related to the threat “Application code confidentiality, (T.Confid-Applic-
Code)” is as follows:
118 Since O.Firewall requires that the TOE ensures isolation of code between the Protected
Application and the other applications, the code of the Protected Application is protected
against unauthorised disclosure, therefore T.Confid-Applic-Code is covered by O.Firewall.
BSI.A.Process-Sec-IC BSI.OE.Process-Sec-IC Phase 5-6
optional
Phase 4
P.Controlled-ES-Loading O.Controlled-ES-Loading Phase 4-6
AUG1.P.Add-Functions AUG1.O.Add-Functions
BSI.T.Leak-Inherent BSI.O.Leak-Inherent
BSI.T.Phys-Probing BSI.O.Phys-Probing
BSI.T.Malfunction BSI.O.Malfunction
BSI.T.Phys-Manipulation BSI.O.Phys-Manipulation
BSI.T.Leak-Forced BSI.O.Leak-Forced
BSI.T.Abuse-Func BSI.O.Abuse-Func
BSI.T.RND BSI.O.RND
AUG4.T.Mem-Access AUG4.O.Mem-Access
T.Confid-Applic-Code O.Firewall
T.Confid-Applic-Data O.Firewall
T.Integ-Applic-Code O.Firewall
T.Integ-Applic-Data O.Firewall
Table 6. Security Objectives versus Assumptions, Threats or Policies (continued)
Assumption, Threat or
Organisational Security Policy
Security Objective Notes
ST33G1M2AM D01 platform Security Target for composition Security objectives (ASE_OBJ)
SMD_ST33G1M2AM_ST_19_002 27/66
119 The added objective for the TOE O.Firewall does not introduce any contradiction in the
security objectives for the TOE.
4.3.3 TOE threat "Application data confidentiality"
120 The justification related to the threat “Application data confidentiality, (T.Confid-Applic-Data)”
is as follows:
121 Since O.Firewall requires that the TOE ensures isolation of data between the Protected
Application and the other applications, the data of the Protected Application is protected
against unauthorised disclosure, therefore T.Confid-Applic-Data is covered by O.Firewall.
4.3.4 TOE threat "Application code integrity"
122 The justification related to the threat “Application code integrity, (T.Integ-Applic-Code)” is as
follows:
123 The threat is related to the alteration of the code of the Protected Application by an attacker.
O.Firewall requires that the TOE ensures isolation of code between the Protected
Application and the other applications, thus protecting the code of the Protected Application
against unauthorised modification. Therefore the threat is covered by O.Firewall.
4.3.5 TOE threat "Application data integrity"
124 The justification related to the threat “Application data integrity, (T.Integ-Applic-Data)” is as
follows:
125 The threat is related to the alteration of the data the Protected Application by an attacker.
Since O.Firewall requires that the TOE ensures complete isolation of data between the
Protected Application and the other applications, the data of the Protected Application is
protected against unauthorised modification, therefore T.Integ-Applic-Data is covered by
O.Firewall.
4.3.6 Organisational security policy "Additional Specific Security
Functionality"
126 The justification related to the organisational security policy "Additional Specific Security
Functionality, (AUG1.P.Add-Functions)” is as follows:
127 Since AUG1.O.Add-Functions requires the TOE to implement exactly the same specific
security functionality as required by AUG1.P.Add-Functions, and in the very same
conditions, the organisational security policy is covered by the objective.
128 Nevertheless the security objectives BSI.O.Leak-Inherent, BSI.O.Phys-Probing, ,
BSI.O.Malfunction, BSI.O.Phys-Manipulation and BSI.O.Leak-Forced define how to
implement the specific security functionality required by AUG1.P.Add-Functions. (Note that
these objectives support that the specific security functionality is provided in a secure way
as expected from AUG1.P.Add-Functions.) Especially BSI.O.Leak-Inherent and
BSI.O.Leak-Forced refer to the protection of confidential data (User Data or TSF data) in
general. User Data are also processed by the specific security functionality required by
AUG1.P.Add-Functions.
129 The added objective for the TOE AUG1.O.Add-Functions does not introduce any
contradiction in the security objectives for the TOE.
Security objectives (ASE_OBJ) ST33G1M2AM D01 platform Security Target for composition
28/66 SMD_ST33G1M2AM_ST_19_002
4.3.7 Organisational security policy "Controlled loading of the Security IC
Embedded Software"
130 The justification related to the organisational security policy "Controlled loading of the
Security IC Embedded Software, (P.Controlled-ES-Loading)” is as follows:
131 Since O.Controlled-ES-Loading requires the TOE to implement exactly the same specific
security functionality as required by P.Controlled-ES-Loading, and in the very same
conditions, the organisational security policy is covered by the objective.
132 The added objective for the TOE O.Controlled-ES-Loading does not introduce any
contradiction in the security objectives.
ST33G1M2AM D01 platform Security Target for composition Security requirements (ASE_REQ)
SMD_ST33G1M2AM_ST_19_002 29/66
5 Security requirements (ASE_REQ)
133 This chapter on security requirements contains a section on security functional
requirements (SFRs) for the TOE (Section 5.1), a section on security assurance
requirements (SARs) for the TOE (Section 5.2), a section on the refinements of these SARs
(Section 5.3) as required by the "BSI-CC-PP-0084-2014" Protection Profile. This chapter
includes a section with the security requirements rationale (Section 5.4).
5.1 Security functional requirements for the TOE
134 Security Functional Requirements (SFRs) from the "BSI-CC-PP-0084-2014" Protection
Profile (PP) are drawn from CCMB-2017-04-002 R5, except the following SFRs, that are
extensions to CCMB-2017-04-002 R5:
• FCS_RNG Generation of random numbers,
• FMT_LIM Limited capabilities and availability,
• FAU_SAS Audit data storage,
• FDP_SDC Stored data confidentiality.
The reader can find their certified definitions in the text of the "BSI-CC-PP-0084-2014"
Protection Profile.
135 All extensions to the SFRs of the "BSI-CC-PP-0084-2014" Protection Profiles (PPs) are
exclusively drawn from CCMB-2017-04-002 R5.
136 All iterations, assignments, selections, or refinements on SFRs have been performed
according to section C.4 of CCMB-2017-04-001 R5. They are easily identified in the
following text as they appear as indicated here. Note that in order to improve readability,
iterations are sometimes expressed within tables.
137 In order to ease the definition and the understanding of these security functional
requirements, a simplified presentation of the TOE Security Policy (TSP) is given in the
following section.
138 The selected security functional requirements for the TOE, their respective origin and type
are summarized in Table 7.
Table 7. Summary of functional security requirements for the TOE
Label Title Addressing Origin Type
FRU_FLT.2 Limited fault tolerance
Malfunction
BSI-CC-PP-
0084-2014
CCMB-2017-04-002
R5
FPT_FLS.1 Failure with preservation
of secure state
Security requirements (ASE_REQ) ST33G1M2AM D01 platform Security Target for composition
30/66 SMD_ST33G1M2AM_ST_19_002
FMT_LIM.1 / Test Limited capabilities Abuse of Test
functionality
BSI-CC-PP-
0084-2014
Extended
FMT_LIM.2 / Test Limited availability
FMT_LIM.1 /
Loader
Limited capabilities
Abuse of Loader
functionality
BSI-CC-PP-
0084-2014
Operated
FMT_LIM.2 /
Loader
Limited availability
FAU_SAS.1 Audit storage Lack of TOE
identification
FDP_SDC.1 Stored data confidentiality
Physical manipulation &
probing
FDP_SDI.2 Stored data integrity
monitoring and action
CCMB-2017-04-002
R5
FPT_PHP.3 Resistance to physical
attack
BSI-CC-PP-
0084-2014
FDP_ITT.1 Basic internal transfer
protection
Leakage
FPT_ITT.1 Basic internal TSF data
transfer protection
FDP_IFC.1 Subset information flow
control
FCS_RNG.1 Random number
generation
Weak cryptographic
quality of random
numbers
BSI-CC-PP-
0084-2014
Operated
Extended
FCS_COP.1 Cryptographic operation
Cipher scheme support
AUG #1
Operated
CCMB-2017-04-002
R5
FDP_ACC.2 /
Memories
Complete access control
Memory access violation
Security Target
Operated
FDP_ACF.1 /
Memories
Security attribute based
access control
AUG #4
Operated
FMT_MSA.3 /
Memories
Static attribute
initialisation
Correct operation
FMT_MSA.1 /
Memories
Management of security
attribute
FMT_SMF.1 /
Memories
Specification of
management functions
Security Target
Operated
Table 7. Summary of functional security requirements for the TOE (continued)
Label Title Addressing Origin Type
ST33G1M2AM D01 platform Security Target for composition Security requirements (ASE_REQ)
SMD_ST33G1M2AM_ST_19_002 31/66
5.1.1 Security Functional Requirements from the Protection Profile
Limited fault tolerance (FRU_FLT.2)
139 The TSF shall ensure the operation of all the TOE’s capabilities when the following failures
occur: exposure to operating conditions which are not detected according to the
requirement Failure with preservation of secure state (FPT_FLS.1).
Failure with preservation of secure state (FPT_FLS.1)
140 The TSF shall preserve a secure state when the following types of failures occur: exposure
to operating conditions which may not be tolerated according to the requirement
Limited fault tolerance (FRU_FLT.2) and where therefore a malfunction could occur.
141 Refinements:
The term “failure” above also covers “circumstances”. The TOE prevents failures for
the “circumstances” defined above.
Regarding application note 14 of BSI-CC-PP-0084-2014, the secure state is reached
by an immediate interrupt or by a reset, depending on the current context.
Regarding application note 15 of BSI-CC-PP-0084-2014, the TOE provides information
on the operating conditions monitored during Security IC Embedded Software
FDP_ITC.1 /
Loader
Import of user data
without security attributes
User data loading access
violation
Security Target
Operated
CCMB-2017-04-002
R5
FDP_ACC.1 /
Loader
Subset access control
FDP_ACF.1 /
Loader
Security attribute based
access control
FMT_MSA.3 /
Loader
Static attribute
initialisation
Correct operation
FMT_MSA.1 /
Loader
Management of security
attribute
FMT_SMR.1 /
Loader
Security roles Abuse of Admin
functionality
FIA_UID.1 /
Loader
Timing of identification
FMT_SMF.1 /
Loader
Specification of
management functions
FDP_ACC.1 /
APPLI_FWL
Subset access control
Protected Application
intrinsic confidentiality
and integrity
FDP_ACF.1 /
APPLI_FWL
Security attribute based
access control
FMT_MSA.3 /
APPLI_FWL
Static attribute
initialisation
Table 7. Summary of functional security requirements for the TOE (continued)
Label Title Addressing Origin Type
Security requirements (ASE_REQ) ST33G1M2AM D01 platform Security Target for composition
32/66 SMD_ST33G1M2AM_ST_19_002
execution and after a warm reset. No audit requirement is however selected in this
Security Target.
Limited capabilities (FMT_LIM.1) / Test
142 The TSF shall be designed and implemented in a manner that limits their capabilities so that
in conjunction with “Limited availability (FMT_LIM.2)” the following policy is enforced:
Limited capability and availability Policy / Test.
Limited availability (FMT_LIM.2) / Test
143 The TSF shall be designed and implemented in a manner that limits their availability so that
in conjunction with “Limited capabilities (FMT_LIM.1) / Test” the following policy is enforced:
Limited capability and availability Policy / Test.
144 SFP_1: Limited capability and availability Policy / Test
Deploying Test Features after TOE Delivery does not allow User Data of the Composite
TOE to be disclosed or manipulated, TSF data to be disclosed or manipulated, software to
be reconstructed and no substantial information about construction of TSF to be gathered
which may enable other attacks.
Audit storage (FAU_SAS.1)
145 The TSF shall provide the test process before TOE Delivery with the capability to store
the Initialisation Data and/or Pre-personalisation Data and/or supplements of the
Security IC Embedded Software in the NVM.
Stored data confidentiality (FDP_SDC.1)
146 The TSF shall ensure the confidentiality of the information of the user data while it is
stored in all the memory areas where it can be stored.
Stored data integrity monitoring and action (FDP_SDI.2)
147 The TSF shall monitor user data stored in containers controlled by the TSF for
integrity errors on all objects, based on the following attributes: user data stored in
all possible memory areas, depending on the integrity control attributes.
148 Upon detection of a data integrity error, the TSF shall signal the error and react.
Resistance to physical attack (FPT_PHP.3)
149 The TSF shall resist physical manipulation and physical probing, to the TSF by
responding automatically such that the SFRs are always enforced.
150 Refinement:
The TSF will implement appropriate mechanisms to continuously counter physical
manipulation and physical probing. Due to the nature of these attacks (especially
manipulation) the TSF can by no means detect attacks on all of its elements.
Therefore, permanent protection against these attacks is required ensuring that
security functional requirements are enforced. Hence, “automatic response” means
here (i)assuming that there might be an attack at any time and (ii)countermeasures
are provided at any time.
ST33G1M2AM D01 platform Security Target for composition Security requirements (ASE_REQ)
SMD_ST33G1M2AM_ST_19_002 33/66
Basic internal transfer protection (FDP_ITT.1)
151 The TSF shall enforce the Data Processing Policy to prevent the disclosure of user data
when it is transmitted between physically-separated parts of the TOE.
Basic internal TSF data transfer protection (FPT_ITT.1)
152 The TSF shall protect TSF data from disclosure when it is transmitted between separate
parts of the TOE.
153 Refinement:
The different memories, the CPU and other functional units of the TOE (e.g. a
cryptographic co-processor) are seen as separated parts of the TOE.
This requirement is equivalent to FDP_ITT.1 above but refers to TSF data instead of
User Data. Therefore, it should be understood as to refer to the same Data
Processing Policy defined under FDP_IFC.1 below.
Subset information flow control (FDP_IFC.1)
154 The TSF shall enforce the Data Processing Policy on all confidential data when they are
processed or transferred by the TOE or by the Security IC Embedded Software.
155 SFP_2: Data Processing Policy
User Data of the Composite TOE and TSF data shall not be accessible from the TOE except
when the Security IC Embedded Software decides to communicate the User Data via an
external interface. The protection shall be applied to confidential data only but without the
distinction of attributes controlled by the Security IC Embedded Software.
Random number generation (FCS_RNG.1)
156 The TSF shall provide a physical random number generator that implements:
• (PTG.2.1) A total failure test detects a total failure of entropy source immediately
when the RNG has started. When a total failure is detected, no random numbers
will be output.
• (PTG.2.2) If a total failure of the entropy source occurs while the RNG is being
operated, the RNG prevents the output of any internal random number that
depends on some raw random numbers that have been generated after the total
failure of the entropy source.
• (PTG.2.3) The online test shall detect non-tolerable statistical defects of the raw
random number sequence (i) immediately when the RNG has started, and (ii)
while the RNG is being operated. The TSF must not output any random numbers
before the power-up online test has finished successfully or when a defect has
been detected.
• (PTG.2.4) The online test procedure shall be effective to detect non-tolerable
weaknesses of the random numbers soon.
• (PTG.2.5) The online test procedure checks the quality of the raw random number
sequence. It is triggered externally. The online test is suitable for detecting non-
tolerable statistical defects of the statistical properties of the raw random
numbers within an acceptable period of time.
Security requirements (ASE_REQ) ST33G1M2AM D01 platform Security Target for composition
34/66 SMD_ST33G1M2AM_ST_19_002
157 The TSF shall provide octets of bits that meet
• (PTG.2.6) Test procedure A does not distinguish the internal random numbers
from output sequences of an ideal RNG.
• (PTG.2.7) The average Shannon entropy per internal random bit exceeds 0.997.
5.1.2 Additional Security Functional Requirements for the cryptographic
services
Cryptographic operation (FCS_COP.1)
158 The TSF shall perform the operations in Table 8 in accordance with a specified
cryptographic algorithm in Table 8 and cryptographic key sizes of Table 8 that meet the
standards in Table 8.
PKCS-1
5.1.3 Additional Security Functional Requirements for the memories
protection
159 The following SFRs are extensions to "BSI-CC-PP-0084-2014" Protection Profile (PP),
related to the memories protection.
Static attribute initialisation (FMT_MSA.3) / Memories
160 The TSF shall enforce the Dynamic Memory Access Control Policy to provide minimally
protective(b)
default values for security attributes that are used to enforce the SFP.
161 The TSF shall allow none to specify alternative initial values to override the default values
when an object or information is created.
Table 8. FCS_COP.1 iterations (cryptographic operations)
Iteration
label
[assignment: list of
cryptographic operations]
[assignment:
cryptographic
algorithm]
[assignment:
cryptographic
key sizes]
[assignment: list
of standards]
TDES(1) * encryption
* decryption
- in Cipher Block Chaining
(CBC) mode
- in Electronic Code Book
(ECB) mode
Triple Data Encryption
Standard (TDES)
168 bits NIST SP 800-67
NIST SP 800-38A
AES * encryption (cipher)
* decryption (inverse cipher)
- in Cipher Block Chaining
(CBC) mode
- in Electronic Code Book
(ECB) mode
Advanced Encryption
Standard
128, 192 and
256 bits
FIPS PUB 197
1. Note that DES and triple DES with two keys are no longer recommended as encryption functions. Hence, Security IC
Embedded Software may need to use triple DES with three keys to achieve a suitable strength.
b. See the Datasheet referenced in Section 7 for actual values.
ST33G1M2AM D01 platform Security Target for composition Security requirements (ASE_REQ)
SMD_ST33G1M2AM_ST_19_002 35/66
Application note:
The security attributes are the set of access rights currently defined. They are dynamically
attached to the subjects and objects locations, i.e. each logical address.
Management of security attributes (FMT_MSA.1) / Memories
162 The TSF shall enforce the Dynamic Memory Access Control Policy to restrict the ability
to modify the security attributes current set of access rights to software running in
privileged mode.
Complete access control (FDP_ACC.2) / Memories
163 The TSF shall enforce the Dynamic Memory Access Control Policy on all subjects
(software), all objects (data including code stored in memories) and all operations
among subjects and objects covered by the SFP.
164 The TSF shall ensure that all operations between any subject controlled by the TSF and any
object controlled by the TSF are covered by an access control SFP.
Security attribute based access control (FDP_ACF.1) / Memories
165 The TSF shall enforce the Dynamic Memory Access Control Policy to objects based on
the following: software mode, the object location, the operation to be performed, and
the current set of access rights.
166 The TSF shall enforce the following rules to determine if an operation among controlled
subjects and controlled objects is allowed: the operation is allowed if and only if the
software mode, the object location and the operation matches an entry in the current
set of access rights.
167 The TSF shall explicitly authorise access of subjects to objects based on the following
additional rules: none.
168 The TSF shall explicitly deny access of subjects to objects based on the following additional
rules: in Admin or User configuration, any access (read, write, execute) to the OST
ROM is denied, and in User configuration, any write access to the ST NVM is denied.
169 Note: It should be noted that this level of policy detail is not needed at the application level.
The composite Security Target writer should describe the ES access control and information
flow control policies instead. Within the ES High Level Design description, the chosen
setting of IC security attributes would be shown to implement the described policies relying
on the IC SFP presented here.
170 The following SFP Dynamic Memory Access Control Policy is defined for the
requirement "Security attribute based access control (FDP_ACF.1) / Memories":
171 SFP_3: Dynamic Memory Access Control Policy
The TSF must control read, write, execute accesses of software to data, based on the
software mode and on the current set of access rights.
Specification of management functions (FMT_SMF.1) / Memories
172 The TSF will be able to perform the following management functions: modification of the
current set of access rights security attributes by software running in privileged
mode, supporting the Dynamic Memory Access Control Policy.
Security requirements (ASE_REQ) ST33G1M2AM D01 platform Security Target for composition
36/66 SMD_ST33G1M2AM_ST_19_002
5.1.4 Additional Security Functional Requirements related to the possible
availability of loading capabilities in phases 4 to 6 of the TOE life-cycle
Limited capabilities (FMT_LIM.1) / Loader
173 The TSF shall be designed and implemented in a manner that limits its capabilities so that in
conjunction with “Limited availability (FMT_LIM.2)” the following policy is enforced: Loader
Limited capability Policy.
174 SFP_4: Loader Limited capability Policy
175 Deploying Loader functionality after blocking of the loader does not allow stored user data to
be disclosed or manipulated by unauthorized user.
Limited availability (FMT_LIM.2) / Loader
176 The TSF shall be designed and implemented in a manner that limits its availability so that in
conjunction with “Limited capabilities (FMT_LIM.1)” the following policy is enforced: Loader
Limited availability Policy.
177 SFP_5: Loader Limited availability Policy
178 The TSF prevents deploying the Loader functionality after blocking of the loader.
Import of user data without security attributes (FDP_ITC.1) / Loader
179 The TSF shall enforce the Loading Access Control Policy when importing user data,
controlled under the SFP, from ouside of the TOE.
180 The TSF shall ignore any security attributes associated with the User data when imported
from outside of the TOE.
181 The TSF shall enforce the following rules when importing user data controlled under the
SFP from outside of the TOE:
• the integrity of the loaded user data is checked at the end of each loading
session,
• the loaded user data is received encrypted, internally decrypted, then stored into
the NVM.
Static attribute initialisation (FMT_MSA.3) / Loader
182 The TSF shall enforce the Loading Access Control Policy to provide restrictive default
values for security attributes that are used to enforce the SFP.
183 The TSF shall allow none to specify alternative initial values to override the default values
when an object or information is created.
Management of security attributes (FMT_MSA.1) / Loader
184 The TSF shall enforce the Loading Access Control Policy to restrict the ability to modify
the security attributes remaining loading sessions to the Loader Administrator.
Subset access control (FDP_ACC.1) / Loader
185 The TSF shall enforce the Loading Access Control Policy on all subjects, object NVM
and all commands.
ST33G1M2AM D01 platform Security Target for composition Security requirements (ASE_REQ)
SMD_ST33G1M2AM_ST_19_002 37/66
Security attribute based access control (FDP_ACF.1) / Loader
186 The TSF shall enforce the Loading Access Control Policy to objects based on the
following: the TOE mode, the user authenticated role, the remaining loading sessions
and the requested command, according to the fixed loader access rights.
187 The TSF shall enforce the following rules to determine if an operation among controlled
subjects and controlled objects is allowed: the command is allowed if and only if the TOE
mode, the user authenticated role, the remaining loading sessions and the requested
command match an entry in the fixed loader access rights.
188 The TSF shall explicitly authorise access of subjects to objects based on the following
additional rules: none.
189 The TSF shall explicitly deny access of subjects to objects based on the following additional
rules: in User mode, no loader command is deployed.
190 The following SFP Loading Access Control Policy is defined for the requirement "Security
attribute based access control (FDP_ACF.1) / Loader":
191 SFP_6: Loading Access Control Policy
192 The TSF must enforce that only authorised users are allowed to download User code and
data into the User NVM or to set the product profile.
The TSF must enforce that only authorised users are allowed to be administrator of the
provided loader functionality.
The TSF controls access to the loader functionality based on the TOE mode, the user
authenticated role, the remaining loading sessions and the requested command according
to the fixed loader access rights.
Specification of management functions (FMT_SMF.1) / Loader
193 The TSF will be able to perform the following management functions: change the TOE
mode, change the user role, change the remaining sessions.
Security roles (FMT_SMR.1) / Loader
194 The TSF shall maintain the roles: Loader and Loader Administrator.
195 The TSF shall be able to associate users with roles.
Timing of identification (FIA_UID.1) / Loader
196 The TSF shall allow boot and authentication command on behalf of the user to be
performed before the user is identified.
197 The TSF shall require each user to be successfully identified before allowing any other TSF
mediated actions on behalf of that user.
5.1.5 Additional Security Functional Requirements related to the Application
Firewall
198 The following SFRs are extensions to "BSI-CC-PP-0084-2014" Protection Profile (PP),
related to the protections by the Application Firewall.
Security requirements (ASE_REQ) ST33G1M2AM D01 platform Security Target for composition
38/66 SMD_ST33G1M2AM_ST_19_002
Subset access control (FDP_ACC.1) / APPLI_FWL
199 The TSF shall enforce the Protected Application Firewall Access Control Policy on the
Protected Application code and data.
Security attribute based access control (FDP_ACF.1) / APPLI_FWL
200 The TSF shall enforce the Protected Application Firewall Access Control Policy to
objects based on the following: Protected Application code and data.
201 The TSF shall enforce the following rules to determine if an operation among controlled
subjects and controlled objects is allowed: Another application cannot read, write,
compare any piece of data or code belonging to the Protected Application.
202 The TSF shall explicitly authorise access of subjects to objects based on the following
additional rules: None.
203 The TSF shall explicitly deny access of subjects to objects based on the following additional
rules:
• Another application cannot read, write, compare any piece of data or code
belonging to the Protected Application.
204 The following SFP Protected Application Firewall Access Control Policy is defined for
the requirement "Security attribute based access control (FDP_ACF.1) / APPLI_FWL":
205 SFP_7: Protected Application Firewall Access Control Policy
206 Another application cannot read, write, compare any piece of data or code belonging to the
Protected Application.
Static attribute initialisation (FMT_MSA.3) / APPLI_FWL
207 The TSF shall enforce the Protected Application Firewall Access Control Policy to
provide restrictive default values for security attributes that are used to enforce the SFP.
208 The TSF shall allow no subject to specify alternative initial values to override the default
values when an object or information is created.
5.2 TOE security assurance requirements
209 Security Assurance Requirements for the TOE for the evaluation of the TOE are those taken
from the Evaluation Assurance Level 5 (EAL5) and augmented by taking the following
components:
• ALC_DVS.2 and AVA_VAN.5.
210 Regarding application note 21 of BSI-CC-PP-0084-2014, the continuously increasing
maturity level of evaluations of Security ICs justifies the selection of a higher-level
assurance package.
211 The set of security assurance requirements (SARs) is presented in Table 9, indicating the
origin of the requirement.
ST33G1M2AM D01 platform Security Target for composition Security requirements (ASE_REQ)
SMD_ST33G1M2AM_ST_19_002 39/66
5.3 Refinement of the security assurance requirements
212 As BSI-CC-PP-0084-2014 defines refinements for selected SARs, these refinements are
also claimed in this Security Target.
213 The main customizing is that the IC Dedicated Software is an operational part of the TOE
after delivery, although it is mainly not available to the user.
Table 9. TOE security assurance requirements
Label Title Origin
ADV_ARC.1 Security architecture description EAL5/BSI-CC-PP-0084-2014
ADV_FSP.5 Complete semi-formal functional specification with
additional error information
EAL5
ADV_IMP.1 Implementation representation of the TSF EAL5/BSI-CC-PP-0084-2014
ADV_INT.2 Well-stuctured internals EAL5
ADV_TDS.4 Semiformal modular design EAL5
AGD_OPE.1 Operational user guidance EAL5/BSI-CC-PP-0084-2014
AGD_PRE.1 Preparative procedures EAL5/BSI-CC-PP-0084-2014
ALC_CMC.4 Production support, acceptance procedures and
automation
EAL5/BSI-CC-PP-0084-2014
ALC_CMS.5 Development tools CM coverage EAL5
ALC_DEL.1 Delivery procedures EAL5/BSI-CC-PP-0084-2014
ALC_DVS.2 Sufficiency of security measures BSI-CC-PP-0084-2014
ALC_LCD.1 Developer defined life-cycle model EAL5/BSI-CC-PP-0084-2014
ALC_TAT.2 Compliance with implementation standards EAL5
ASE_CCL.1 Conformance claims EAL5/BSI-CC-PP-0084-2014
ASE_ECD.1 Extended components definition EAL5/BSI-CC-PP-0084-2014
ASE_INT.1 ST introduction EAL5/BSI-CC-PP-0084-2014
ASE_OBJ.2 Security objectives EAL5/BSI-CC-PP-0084-2014
ASE_REQ.2 Derived security requirements EAL5/BSI-CC-PP-0084-2014
ASE_SPD.1 Security problem definition EAL5/BSI-CC-PP-0084-2014
ASE_TSS.1 TOE summary specification EAL5/BSI-CC-PP-0084-2014
ATE_COV.2 Analysis of coverage EAL5/BSI-CC-PP-0084-2014
ATE_DPT.3 Testing: modular design EAL5
ATE_FUN.1 Functional testing EAL5/BSI-CC-PP-0084-2014
ATE_IND.2 Independent testing - sample EAL5/BSI-CC-PP-0084-2014
AVA_VAN.5 Advanced methodical vulnerability analysis BSI-CC-PP-0084-2014
Security requirements (ASE_REQ) ST33G1M2AM D01 platform Security Target for composition
40/66 SMD_ST33G1M2AM_ST_19_002
214 Regarding application note 22 of BSI-CC-PP-0084-2014, the refinements for all the
assurance families have been reviewed for the hierarchically higher-level assurance
components selected in this Security Target.
215 The text of the impacted refinements of BSI-CC-PP-0084-2014 is reproduced in the next
sections.
216 For reader’s ease, an impact summary is provided in Table 10.
5.3.1 Refinement regarding functional specification (ADV_FSP)
217 Although the IC Dedicated Test Software is a part of the TOE, the test functions of the IC
Dedicated Test Software are not described in the Functional Specification because the IC
Dedicated Test Software is considered as a test tool delivered with the TOE but not
providing security functions for the operational phase of the TOE. The IC Dedicated
Software provides security functionalities as soon as the TOE becomes operational
(boot software). These are properly identified in the delivered documentation.
218 The Functional Specification refers to datasheet to trace security features that do not
provide any external interface but that contribute to fulfil the SFRs e.g. like physical
protection. Thereby they are part of the complete instantiation of the SFRs.
219 The Functional Specification refers to design specifications to detail the mechanisms
against physical attacks described in a more general way only, but detailed enough to be
able to support Test Coverage Analysis also for those mechanisms where inspection of the
layout is of relevance or tests beside the TSFI may be needed.
220 The Functional Specification refers to data sheet to specify operating conditions of the
TOE. These conditions include but are not limited to the frequency of the clock, the power
supply, and the temperature.
Table 10. Impact of EAL5 selection on BSI-CC-PP-0084-2014 refinements
Assurance
Family
BSI-CC-PP-
0084-2014
Level
ST
Level
Impact on refinement
ADO_DEL 1 1 None
ALC_DVS 2 2 None
ALC_CMS 4 5 None, refinement is still valid
ALC_CMC 4 4 None
ADV_ARC 1 1 None
ADV_FSP
4 5
Presentation style changes, IC Dedicated
Software is included
ADV_IMP 1 1 None
ATE_COV 2 2 IC Dedicated Software is included
AGD_OPE 1 1 None
AGD_PRE 1 1 None
AVA_VAN 5 5 None
ST33G1M2AM D01 platform Security Target for composition Security requirements (ASE_REQ)
SMD_ST33G1M2AM_ST_19_002 41/66
221 All functions and mechanisms which control access to the functions provided by the IC
Dedicated Test Software (refer to the security functional requirement (FMT_LIM.2)) are part
of the Functional Specification. Details will be given in the document for ADV_ARC, refer to
Section 6.2.1.5. In addition, all these functions and mechanisms are subsequently be
refined according to all relevant requirements of the Common Criteria assurance class ADV
because these functions and mechanisms are active after TOE Delivery and need to be part
of the assurance aspects Tests (class ATE) and Vulnerability Assessment (class AVA).
Therefore, all necessary information is provided to allow tests and vulnerability assessment.
222 Since the selected higher-level assurance component requires a security functional
specification presented in a “semi-formal style" (ADV_FSP.5.2C) the changes affect the
style of description, the BSI-CC-PP-0084-2014 refinements can be applied with changes
covering the IC Dedicated Test Software and are valid for ADV_FSP.5.
5.3.2 Refinement regarding test coverage (ATE_COV)
223 The TOE is tested under different operating conditions within the specified ranges. These
conditions include but are not limited to the frequency of the clock, the power supply, and
the temperature. This means that “Fault tolerance (FRU_FLT.2)” is proven for the complete
TSF. The tests must also cover functions which may be affected by “ageing” (such as
EEPROM NVM writing).
224 The existence and effectiveness of measures against physical attacks (as specified by the
functional requirement FPT_PHP.3) cannot be tested in a straightforward way. Instead
STMicroelectronics provides evidence that the TOE actually has the particular physical
characteristics (especially layout design principles). This is done by checking the layout
(implementation or actual) in an appropriate way. The required evidence pertains to the
existence of mechanisms against physical attacks (unless being obvious).
225 The IC Dedicated Test Software is seen as a “test tool” being delivered as part of the TOE.
However, the Test Features do not provide security functionality. Therefore, Test Features
need not to be covered by the Test Coverage Analysis but all functions and mechanisms
which limit the capability of the functions (cf. FMT_LIM.1) and control access to the
functions (cf. FMT_LIM.2) provided by the IC Dedicated Test Software must be part of the
Test Coverage Analysis. The IC Dedicated Software provides security functionalities as
soon as the TOE becomes operational (boot software). These are part of the Test
Coverage Analysis.
5.4 Security Requirements rationale
5.4.1 Rationale for the Security Functional Requirements
226 Just as for the security objectives rationale of Section 4.3, the main line of this rationale is
that the inclusion of all the security requirements of the BSI-CC-PP-0084-2014 protection
profile, together with those in AUG, and with those introduced in this Security Target,
guarantees that all the security objectives identified in Section 4 are suitably addressed by
the security requirements stated in this chapter, and that the latter together form an
internally consistent whole.
Security requirements (ASE_REQ) ST33G1M2AM D01 platform Security Target for composition
42/66 SMD_ST33G1M2AM_ST_19_002
Table 11. Security Requirements versus Security Objectives
Security Objective TOE Security Functional and Assurance Requirements
BSI.O.Leak-Inherent Basic internal transfer protection FDP_ITT.1
Basic internal TSF data transfer protection FPT_ITT.1
Subset information flow control FDP_IFC.1
BSI.O.Phys-Probing Stored data confidentiality FDP_SDC.1
Resistance to physical attack FPT_PHP.3
BSI.O.Malfunction Limited fault tolerance FRU_FLT.2
Failure with preservation of secure state FPT_FLS.1
BSI.O.Phys-Manipulation Stored data integrity monitoring and action FDP_SDI.2
Resistance to physical attack FPT_PHP.3
BSI.O.Leak-Forced All requirements listed for BSI.O.Leak-Inherent
FDP_ITT.1, FPT_ITT.1, FDP_IFC.1
plus those listed for BSI.O.Malfunction and BSI.O.Phys-
Manipulation
FRU_FLT.2, FPT_FLS.1, FDP_SDI.2, FPT_PHP.3
BSI.O.Abuse-Func Limited capabilities FMT_LIM.1 / Test
Limited availability FMT_LIM.2 / Test
plus those for BSI.O.Leak-Inherent, BSI.O.Phys-Probing,
BSI.O.Malfunction, BSI.O.Phys-Manipulation, BSI.O.Leak-Forced
FDP_ITT.1, FPT_ITT.1, FDP_IFC.1, FDP_SDC.1, FDP_SDI.2,
FPT_PHP.3, FRU_FLT.2, FPT_FLS.1
BSI.O.Identification Audit storage FAU_SAS.1
BSI.O.RND Random number generation FCS_RNG.1
plus those for BSI.O.Leak-Inherent, BSI.O.Phys-Probing,
BSI.O.Malfunction, BSI.O.Phys-Manipulation, BSI.O.Leak-Forced
FDP_ITT.1, FPT_ITT.1, FDP_IFC.1, FDP_IFC.1, FDP_SDC.1,
FPT_PHP.3, FRU_FLT.2, FPT_FLS.1
BSI.OE.Resp-Appl Not applicable
BSI.OE.Process-Sec-IC Not applicable
AUG1.O.Add-Functions Cryptographic operation FCS_COP.1
AUG4.O.Mem-Access Complete access control FDP_ACC.2 / Memories
Security attribute based access control FDP_ACF.1 / Memories
Static attribute initialisation FMT_MSA.3 / Memories
Management of security attribute FMT_MSA.1 / Memories
Specification of management functions FMT_SMF.1 / Memories
BSI.O.Cap-Avail-Loader Limited capabilities FMT_LIM.1 / Loader
Limited availability FMT_LIM.2 / Loader
ST33G1M2AM D01 platform Security Target for composition Security requirements (ASE_REQ)
SMD_ST33G1M2AM_ST_19_002 43/66
227 As origins of security objectives have been carefully kept in their labelling, and origins of
security requirements have been carefully identified in Table 7 and Table 11, it can be
verified that the justifications provided by the BSI-CC-PP-0084-2014 protection profile and
AUG can just be carried forward to their union.
228 From Table 5, it is straightforward to identify additional security objectives for the TOE
(AUG1.O.Add-Functions and AUG4.O.Mem-Access) tracing back to AUG, and additional
objectives (O.Controlled-ES-Loading and O.Firewall) introduced in this Security Target. This
rationale must show that security requirements suitably address them all.
229 Furthermore, a careful observation of the requirements listed in Table 7 and Table 11 shows
that:
• there are security requirements introduced from AUG (FCS_COP.1, FDP_ACC.2 /
Memories, FDP_ACF.1 / Memories, FMT_MSA.3 / Memories and FMT_MSA.1 /
Memories),
• there are additional security requirements introduced by this Security Target
(FDP_ITC.1 / Loader, FDP_ACC.1 / Loader, FDP_ACF.1 / Loader, FMT_MSA.3 /
Loader, FMT_MSA.1 / Loader, FMT_SMF.1 / Loader, FMT_SMR.1 / Loader, FIA_UID.1
/ Loader, FMT_SMF.1 / Memories, FDP_ACC.1 / APPLI_FWL, FDP_ACF.1 /
APPLI_FWL, and FMT_MSA.3 / APPLI_FWL, and various assurance requirements of
EAL5+).
230 Though it remains to show that:
• security objectives from this Security Target and from AUG are addressed by security
requirements stated in this chapter,
• additional security requirements from this Security Target and from AUG are mutually
supportive with the security requirements from the BSI-CC-PP-0084-2014 protection
profile, and they do not introduce internal contradictions,
• all dependencies are still satisfied.
231 The justification that the additional security objectives are suitably addressed, that the
additional security requirements are mutually supportive and that, together with those
already in BSI-CC-PP-0084-2014, they form an internally consistent whole, is provided in
the next subsections.
O.Controlled-ES-Loading Import of user data without security attributes FDP_ITC.1 / Loader
Subset access control FDP_ACC.1 / Loader
Security attribute based access control FDP_ACF.1 / Loader
Static attribute initialisation FMT_MSA.3 / Loader
Management of security attribute FMT_MSA.1 / Loader
Specification of management functions FMT_SMF.1 / Loader
Security roles FMT_SMR.1 / Loader
Timing of identification FIA_UID.1 / Loader
O.Firewall Subset access control FDP_ACC.1 / APPLI_FWL
Security attribute based access control FDP_ACF.1 / APPLI_FWL
Static attribute initialisation FMT_MSA.3 / APPLI_FWL
Table 11. Security Requirements versus Security Objectives
Security Objective TOE Security Functional and Assurance Requirements
Security requirements (ASE_REQ) ST33G1M2AM D01 platform Security Target for composition
44/66 SMD_ST33G1M2AM_ST_19_002
5.4.2 Additional security objectives are suitably addressed
Security objective “Dynamic Area based Memory Access Control
(AUG4.O.Mem-Access)”
232 The justification related to the security objective “Dynamic Area based Memory Access
Control (AUG4.O.Mem-Access)” is as follows:
233 The security functional requirements "Complete access control (FDP_ACC.2) / Memories"
and "Security attribute based access control (FDP_ACF.1) / Memories", with the related
Security Function Policy (SFP) “Dynamic Memory Access Control Policy” exactly require
to implement a Dynamic area based memory access control as demanded by
AUG4.O.Mem-Access. Therefore, FDP_ACC.2 / Memories and FDP_ACF.1 / Memories
with their SFP are suitable to meet the security objective.
234 The security functional requirement "Static attribute initialisation (FMT_MSA.3) / Memories"
requires that the TOE provides default values for security attributes. The ability to update
the security attributes is restricted to privileged subject(s) as further detailed in the
security functional requirement "Management of security attributes (FMT_MSA.1) /
Memories". These management functions ensure that the required access control can be
realised using the functions provided by the TOE.
Security objective “Additional Specific Security Functionality (AUG1.O.Add-
Functions)”
235 The justification related to the security objective “Additional Specific Security Functionality
(AUG1.O.Add-Functions)” is as follows:
236 The security functional requirements “Cryptographic operation (FCS_COP.1)” exactly
require those functions to be implemented that are demanded by AUG1.O.Add-Functions.
Therefore, FCS_COP.1 is suitable to meet the security objective.
Security objective “Controlled loading of the Security IC Embedded Software
(O.Controlled-ES-Loading)”
237 The justification related to the security objective “Controlled loading of the Security IC
Embedded Software (O.Controlled-ES-Loading)” is as follows:
238 The security functional requirements "Import of user data without security attributes
(FDP_ITC.1) / Loader", "Subset access control (FDP_ACC.1) / Loader" and "Security
attribute based access control (FDP_ACF.1) / Loader", with the related Security Function
Policy (SFP) “Loading Access Control Policy” exactly require to implement a controlled
loading of the Security IC Embedded Software as demanded by O.Controlled-ES-Loading.
Therefore, FDP_ITC.1 / Loader, FDP_ACC.1 / Loader and FDP_ACF.1 / Loader with their
SFP are suitable to meet the security objective.
239 The security functional requirement "Static attribute initialisation (FMT_MSA.3) / Loader"
requires that the TOE provides default values for security attributes. The ability to update
the security attributes is restricted to privileged subject(s) as further detailed in the security
functional requirement "Management of security attributes (FMT_MSA.1) / Loader". The
security functional requirements"Security roles (FMT_SMR.1) / Loader" and "Timing of
identification (FIA_UID.1) / Loader" specifies the roles that the TSF recognises and the
actions authorised before their identification.The security functional requirement
"Specification of management functions (FMT_SMF.1) / Loader" provides additional
controlled facility for adapting the loader behaviour to the user’s needs. These management
ST33G1M2AM D01 platform Security Target for composition Security requirements (ASE_REQ)
SMD_ST33G1M2AM_ST_19_002 45/66
functions ensure that the required access control, associated to the loading feature, can be
realised using the functions provided by the TOE.
Security objective “Application firewall (O.Firewall)”
240 The justification related to the security objective “Application firewall (O.Firewall)” is as
follows:
241 The security functional requirements "Subset access control (FDP_ACC.1) / APPLI_FWL"
and "Security attribute based access control (FDP_ACF.1) / APPLI_FWL", supported by
"Static attribute initialisation (FMT_MSA.3) / APPLI_FWL", require that no application can
read, write, compare any piece of data or code belonging to a Protected Application. This
meets the objective O.Firewall.
5.4.3 Additional security requirements are consistent
"Cryptographic operation (FCS_COP.1)"
242 This security requirement has already been argued in Section : Security objective
“Additional Specific Security Functionality (AUG1.O.Add-Functions)” above.
"Static attribute initialisation (FMT_MSA.3 / Memories),
Management of security attributes (FMT_MSA.1 / Memories),
Complete access control (FDP_ACC.2 / Memories),
Security attribute based access control (FDP_ACF.1 / Memories)"
243 These security requirements have already been argued in Section : Security objective
“Dynamic Area based Memory Access Control (AUG4.O.Mem-Access)” above.
"Import of user data without security attribute (FDP_ITC.1 / Loader),
Static attribute initialisation (FMT_MSA.3 / Loader),
Management of security attributes (FMT_MSA.1 / Loader),
Subset access control (FDP_ACC.1 / Loader),
Security attribute based access control (FDP_ACF.1 / Loader),
Specification of management function (FMT_SMF.1 / Loader),
Security roles (FMT_SMR.1 / Loader),
Timing of identification(FIA_UID.1 / Loader)"
244 These security requirements have already been argued in Section : Security objective
“Controlled loading of the Security IC Embedded Software (O.Controlled-ES-Loading)”
above.
"Subset access control (FDP_ACC.1 / APPLI_FWL),
Security attribute based access control (FDP_ACF.1 / APPLI_FWL),
Static attribute initialisation (FMT_MSA.3 / APPLI_FWL),
245 These security requirements have already been argued in Section : Security objective
“Application firewall (O.Firewall)” above.
Security requirements (ASE_REQ) ST33G1M2AM D01 platform Security Target for composition
46/66 SMD_ST33G1M2AM_ST_19_002
5.4.4 Dependencies of Security Functional Requirements
246 All dependencies of Security Functional Requirements have been fulfilled in this Security
Target except :
• those justified in the BSI-CC-PP-0084-2014 protection profile security requirements
rationale,
• those justified in AUG security requirements rationale,
• the dependency of FCS_COP.1 on FCS_CKM.4 (see discussion below).
• the dependency of FMT_MSA.3 / APPLI_FWL on FMT_MSA.1 and FMT_SMR.1 (see
discussion below).
247 Details are provided in Table 12 below.
Table 12. Dependencies of security functional requirements
Label Dependencies
Fulfilled by security
requirements in this
Security Target
Dependency already
in BSI-CC-PP-0084-2014 or in
AUG
FRU_FLT.2 FPT_FLS.1 Yes Yes, BSI-CC-PP-0084-2014
FPT_FLS.1 None No dependency Yes, BSI-CC-PP-0084-2014
FMT_LIM.1 / Test FMT_LIM.2 / Test Yes Yes, BSI-CC-PP-0084-2014
FMT_LIM.2 / Test FMT_LIM.1 / Test Yes Yes, BSI-CC-PP-0084-2014
FMT_LIM.1 / Loader FMT_LIM.2 / Loader Yes Yes, BSI-CC-PP-0084-2014
FMT_LIM.2 / Loader FMT_LIM.1 / Loader Yes Yes, BSI-CC-PP-0084-2014
FAU_SAS.1 None No dependency Yes, BSI-CC-PP-0084-2014
FDP_SDC.1 None No dependency Yes, BSI-CC-PP-0084-2014
FDP_SDI.2 None No dependency Yes, BSI-CC-PP-0084-2014
FPT_PHP.3 None No dependency Yes, BSI-CC-PP-0084-2014
FDP_ITT.1
FDP_ACC.1 or
FDP_IFC.1
Yes Yes, BSI-CC-PP-0084-2014
FPT_ITT.1 None No dependency Yes, BSI-CC-PP-0084-2014
FDP_IFC.1 FDP_IFF.1
No, see BSI-CC-PP-
0084-2014
Yes, BSI-CC-PP-0084-2014
FCS_RNG.1 None No dependency Yes, BSI-CC-PP-0084-2014
FCS_COP.1
[FDP_ITC.1 or
FDP_ITC.2 or
FCS_CKM.1]
Yes, by FDP_ITC.1, see
discussion below Yes, AUG #1
FCS_CKM.4 No, see discussion below
FDP_ACC.2 /
Memories
FDP_ACF.1 /
Memories
Yes No, CCMB-2017-04-002 R5
ST33G1M2AM D01 platform Security Target for composition Security requirements (ASE_REQ)
SMD_ST33G1M2AM_ST_19_002 47/66
FDP_ACF.1 /
Memories
FDP_ACC.1 /
Memories
Yes, by FDP_ACC.2 /
Memories
Yes, AUG #4
FMT_MSA.3 /
Memories
Yes
FMT_MSA.3 /
Memories
FMT_MSA.1 /
Memories
Yes
Yes, AUG #4
FMT_SMR.1 /
Memories
No, see AUG #4
FMT_MSA.1 /
Memories
[FDP_ACC.1 /
Memories or
FDP_IFC.1]
Yes, by FDP_ACC.2 /
Memories and
FDP_IFC.1
Yes, AUG #4
FMT_SMF.1 /
Memories
Yes No, CCMB-2017-04-002 R5
FMT_SMR.1 /
Memories
No, see AUG #4 Yes, AUG #4
FMT_SMF.1 /
Memories
None No dependency No, CCMB-2017-04-002 R5
FMT_ITC.1 / Loader
[FDP_ACC.1 /
Loader or
FDP_IFC.1]
Yes
No, CCMB-2017-04-002 R5
FMT_MSA.3 /
Loader
Yes
FDP_ACC.1 /
Loader
FDP_ACF.1 / Loader Yes No, CCMB-2017-04-002 R5
FDP_ACF.1 /
Loader
FDP_ACC.1 /
Loader
Yes
No, CCMB-2017-04-002 R5
FMT_MSA.3 /
Loader
Yes
FMT_MSA.3 /
Loader
FMT_MSA.1 /
Loader
Yes
No, CCMB-2017-04-002 R5
FMT_SMR.1 /
Loader
Yes
FMT_MSA.1 /
Loader
[FDP_ACC.1 /
Loader or
FDP_IFC.1]
Yes
No, CCMB-2017-04-002 R5
FDP_SMF.1 / Loader Yes
FDP_SMR.1 /
Loader
Yes
Table 12. Dependencies of security functional requirements (continued)
Label Dependencies
Fulfilled by security
requirements in this
Security Target
Dependency already
in BSI-CC-PP-0084-2014 or in
AUG
Security requirements (ASE_REQ) ST33G1M2AM D01 platform Security Target for composition
48/66 SMD_ST33G1M2AM_ST_19_002
248 Part 2 of the Common Criteria defines the dependency of "Cryptographic operation
(FCS_COP.1)" on "Import of user data without security attributes (FDP_ITC.1)" or "Import of
user data with security attributes (FDP_ITC.2)" or "Cryptographic key generation
(FCS_CKM.1)". In this particular TOE, "Import of user data without security attributes
(FDP_ITC.1) / Loader" may be used for the purpose of creating cryptographic keys, but
also, the ES has all possibilities to implement its own creation function, in conformance with
its security policy.
249 Part 2 of the Common Criteria defines the dependency of "Cryptographic operation
(FCS_COP.1)" on "Cryptographic key destruction (FCS_CKM.4)". In this particular TOE,
there is no specific function for the destruction of the keys. The ES has all possibilities to
implement its own destruction function, in conformance with its security policy. Therefore,
FCS_CKM.4 is not defined in this ST.
250 Part 2 of the Common Criteria defines the dependency of "Static attribute initialisation
(FMT_MSA.3) / APPLI_FWL" on "Management of security attributes (FMT_MSA.1)" and
"Security roles (FMT_SMR.1)". For this particular instantiation of the access control
attributes aimed at protecting a Protected Application code and data from unauthorised
accesses, the security attributes are only static, initialized at product start. Therefore, there
is no need to identify management capabilities and associated roles in form of Security
Functional Requirements "FMT_MSA.1" and "FMT_SMR.1".
5.4.5 Rationale for the Assurance Requirements
Security assurance requirements added to reach EAL5 (Table 9)
251 Regarding application note 21 of BSI-CC-PP-0084-2014, this Security Target chooses EAL5
with augmentations because developers and users require a high level of independently
assured security in a planned development and require a rigorous development approach
without incurring unreasonable costs attributable to specialist security engineering
techniques.
FMT_SMR.1 /
Loader
FIA_UID.1 / Loader Yes No, CCMB-2017-04-002 R5
FIA_UID.1 / Loader None No dependency No, CCMB-2017-04-002 R5
FDP_SMF.1 /
Loader
None No dependency No, CCMB-2017-04-002 R5
FDP_ACC.1 /
APPLI_FWL
FDP_ACF.1 /
APPLI_FWL
Yes No, CCMB-2017-04-002 R5
FDP_ACF.1 /
APPLI_FWL
FDP_ACC.1 /
APPLI_FWL
Yes
No, CCMB-2017-04-002 R5
FMT_MSA.3 /
APPLI_FWL
Yes
FMT_MSA.3 /
APPLI_FWL
FMT_MSA.1 No, see discussion below
No, CCMB-2017-04-002 R5
FMT_SMR.1 No, see discussion below
Table 12. Dependencies of security functional requirements (continued)
Label Dependencies
Fulfilled by security
requirements in this
Security Target
Dependency already
in BSI-CC-PP-0084-2014 or in
AUG
ST33G1M2AM D01 platform Security Target for composition Security requirements (ASE_REQ)
SMD_ST33G1M2AM_ST_19_002 49/66
252 EAL5 represents a meaningful increase in assurance from EAL4 by requiring semiformal
design descriptions, a more structured (and hence analyzable) architecture, and improved
mechanisms and/or procedures that provide confidence that the TOE will not be tampered
during development.
253 The assurance components in an evaluation assurance level (EAL) are chosen in a way that
they build a mutually supportive and complete set of components. All dependencies
introduced by the requirements chosen for augmentation are fulfilled. Therefore, these
components add additional assurance to EAL5, but the mutual support of the requirements
and the internal consistency is still guaranteed.
254 Note that detailed and updated refinements for assurance requirements are given in
Section 5.3.
Dependencies of assurance requirements
255 Dependencies of security assurance requirements are fulfilled by the EAL5 package
selection.
256 The augmentation to this package are identified in paragraph 209 and do not introduce
dependencies not already satisfied by the EAL5 package.
TOE summary specification (ASE_TSS) ST33G1M2AM D01 platform Security Target for composi-
50/66 SMD_ST33G1M2AM_ST_19_002
6 TOE summary specification (ASE_TSS)
257 This section demonstrates how the TOE meets each Security Functional Requirement,
which will be further detailed in the ADV_FSP documents.
6.1 Limited fault tolerance (FRU_FLT.2)
258 The TSF provides limited fault tolerance, by managing a certain number of faults or errors
that may happen, related to random number generation, power supply, data flows and
cryptographic operations, thus preventing risk of malfunction.
6.2 Failure with preservation of secure state (FPT_FLS.1)
259 The TSF provides preservation of secure state by detecting and managing the following
failures:
• High voltage supply,
• Glitches,
• Die integrity violation detection,
• Errors on memories and registers,
• CPU errors,
• MPU errors,
• Faults on crypto processors,
• etc...
260 The ES can generate a software reset, either simple or infinite (reset and wait).
6.3 Limited capabilities (FMT_LIM.1) / Test
261 The TSF ensures that only very limited test capabilities are available in User configuration,
in accordance with SFP_1: Limited capability and availability Policy / Test.
6.4 Limited capabilities (FMT_LIM.1) / Loader
262 The TSF ensures that the Secure Flash Loader and the final test capabilities are unavailable
in User configuration, in accordance with SFP_4: Loader Limited capability Policy.
6.5 Limited availability (FMT_LIM.2) / Test & (FMT_LIM.2) /
Loader
263 The TOE is either in Test, Admin (aka Issuer) or User configuration.
ST33G1M2AM D01 platform Security Target for composition TOE summary specification
SMD_ST33G1M2AM_ST_19_002 51/66
264 The only authorised TOE configuration modifications are:
• Test to Admin configuration,
• Test to User configuration,
• Admin to User configuration.
265 The TSF ensures the switching and the control of TOE configuration.
266 The TSF reduces the available features depending on the TOE configuration:
• the full test features are unavailable in User and Admin configuration,
• the Secure Flash Loader and the Final Test OS are unavailable in User configuration,
• the diagnostic test features are reserved to ST in User and Admin configuration.
6.6 Stored data confidentiality (FDP_SDC.1)
267 The TSF ensures confidentiality of the User Data, thanks to the following features:
• Memories scrambling and encryption,
• Protection of NVM sectors,
• MPU,
• LPU.
6.7 Stored data integrity monitoring and action (FDP_SDI.2)
268 The TSF ensures stored data integrity, thanks to the following features:
• Memories parity control,
• Protection of NVM sectors,
• MPU,
• LPU.
6.8 Audit storage (FAU_SAS.1)
269 In User configuration, the TOE provides commands to store data and/or pre-personalisation
data and/or supplements of the ES in the NVM. These commands are only available to
authorized processes, and only until phase 6.
6.9 Resistance to physical attack (FPT_PHP.3)
270 The TSF ensures resistance to physical tampering, thanks to the following features:
• The TOE implements a set of countermeasures that reduce the exploitability of
physical probing.
• The TOE is physically protected by active shields that command an automatic reaction
on die integrity violation detection.
TOE summary specification (ASE_TSS) ST33G1M2AM D01 platform Security Target for composi-
52/66 SMD_ST33G1M2AM_ST_19_002
6.10 Basic internal transfer protection (FDP_ITT.1), Basic internal
TSF data transfer protection (FPT_ITT.1) & Subset
information flow control (FDP_IFC.1)
271 The TSF prevents the disclosure of internal and user data thanks to:
• Memories scrambling and encryption,
• Bus encryption,
• RAM content destruction and register cleaning upon reset,
• Clocks jittering,
• Mechanisms for operation execution concealment.
6.11 Random number generation (FCS_RNG.1)
272 The TSF provides 8-bit true random numbers that can be qualified with the test metrics
required by the BSI-AIS20/AIS31 standard for a PTG.2 class device.
6.12 Cryptographic operation: EDES operation (FCS_COP.1) /
EDES
273 The TOE provides an EDES+ accelerator that has the capability to perform 3-key Triple
DES(c)
encryption and decryption in Electronic Code Book (ECB) and Cipher Block
Chaining (CBC) mode conformant to NIST SP 800-67 and NIST SP 800-38A.
6.13 Cryptographic operation: AES operation (FCS_COP.1) / AES
274 The AES accelerator provides the following standard AES cryptographic operations for key
sizes of 128, 192 and 256 bits, conformant to FIPS PUB 197 with intrinsic counter-measures
against attacks:
• cipher,
• inverse cipher.
275 The AES accelerator can operate in Electronic Code Book (ECB) and Cipher Block
Chaining (CBC) mode.
6.14 Static attribute initialisation (FMT_MSA.3) / Memories
276 The TOE enforces a default memory protection policy when none other is programmed by
the ES.
c. Note that DES and triple DES with two keys are no longer recommended as encryption functions. Hence, Security IC
Embedded Software may need to use triple DES with three keys to achieve a suitable strength.
ST33G1M2AM D01 platform Security Target for composition TOE summary specification
SMD_ST33G1M2AM_ST_19_002 53/66
6.15 Management of security attributes (FMT_MSA.1) / Memories
& Specification of management functions (FMT_SMF.1) /
Memories
277 The TOE provides a dynamic Memory Protection Unit (MPU), that can be configured by the
ES.
6.16 Complete access control (FDP_ACC.2) / Memories & Security
attribute based access control (FDP_ACF.1) / Memories
278 The TOE enforces the dynamic memory protection policy for data access and code access
thanks to a dynamic Memory Protection Unit (MPU), programmed by the ES.
Overriding the MPU set of access rights, the TOE enforces additional protections on specific
parts of the memories.
6.17 Static attribute initialisation (FMT_MSA.3) / Loader
279 In Admin configuration, the System Firmware provides restrictive default values for the
Flash Loader security attributes.
6.18 Management of security attributes (FMT_MSA.1) / Loader &
Specification of management functions (FMT_SMF.1) /
Loader
280 In Admin configuration, the System Firmware provides the capability to change part of the
Flash Loader security attributes, only once in the product lifecycle.
6.19 Subset access control (FDP_ACC.1) / Loader, Security
attribute based access control (FDP_ACF.1) / Loader,
Security roles (FMT_SMR.1) / Loader & Timing of
identification (FIA_UID.1) / Loader
281 In Admin configuration, the System Firmware grants access to the Flash Loader functions,
only after presentation of the required valid passwords.
6.20 Import of user data without security attributes (FDP_ITC.1) /
Loader
282 In Admin configuration, the System Firmware provides the capability of loading user data
into the NVM, while ensuring confidentiality and integrity of the loaded data.
TOE summary specification (ASE_TSS) ST33G1M2AM D01 platform Security Target for composi-
54/66 SMD_ST33G1M2AM_ST_19_002
6.21 Subset access control (FDP_ACC.1) / APPLI_FWL & Security
attribute based access control (FDP_ACF.1) / APPLI_FWL
283 The Library Protection Unit is used to isolate the Protected Application firmware (code and
data) from the rest of the code embedded in the device.
6.22 Static attribute initialisation (FMT_MSA.3) / APPLI_FWL
284 At product start, all the static attributes are initialised, which are needed to protect the
segments where the Protected Application code and data are stored.
ST33G1M2AM D01 platform Security Target for composition Identification
SMD_ST33G1M2AM_ST_19_002 55/66
7 Identification
Table 13. TOE components
IC Maskset name IC version
Master identification
number
Firmware version OST version
K8H0A G
00F2h (ST33G1M2A0)
1.3.2 2.2
00F3h (ST33G1M2M0)
Table 14. Guidance documentation
Component description Reference Version
ST33G1M2A: Secure MCU with 32-bit ARM SecurCore
SC300 - Datasheet
DS_ST33G1M2A 3
ST33G1M2M: Secure MCU with 32-bit ARM SecurCore
SC300 - Datasheet
DS_ST33G1M2M 7
ST33G1M2A, ST33G1M2M: CMOS M10+ 80-nm
technology die and wafer delivery description
DD_ST33G1M2A_M 2
ARM® Cortex SC300 r0p0 Technical Reference Manual ARM DDI 0337F F
ARM® Cortex M3 r2p0 Technical Reference Manual ARM DDI 0337F3c F3c
ARM® SC300 r0p0 SecurCore Technical Reference Manual
Supplement 1A
ARM DDI 0337 Supp 1A A
ARM® SecurCore® SC300 ES_SC300 1
ST33 ARM Execute-only memory support for SecurCore®
SC300 devices - Application note
AN_33_EXE 2
ST33 uniform timing application note AN_33_UT 2
ST33G1M2A / ST33G1M2M firmware - User manual UM_ST33G1M2A_M_FW 11
Flash memory loader installation guide for the ST33G1M2A
and ST33G1M2M platforms - User manual
UM_33GA_FL 3
ST33G and ST33H Firmware support for LPU regions -
application note
AN_33G_33H_LPU 1
ST33G and ST33H Secure MCU platforms - Security
Guidance
AN_SECU_ST33 9
ST33G and ST33H Power supply glitch detector
characteristics - application note
AN_33_GLITCH 2
ST33G and ST33H - AIS31 Compliant Random Number -
User Manual
UM_33G_33H_AIS31 3
ST33G and ST33H - AIS31 Reference implementation -
Startup, online and total failure tests - User manual
AN_33G_33H_AIS31 1
Identification ST33G1M2AM D01 platform Security Target for composition
56/66 SMD_ST33G1M2AM_ST_19_002
Table 15. Sites list
Site Address Activities(1)
Amkor ATP1 AMKOR ATP1
Km 22 East Service Road,
South Superhighway, Muntinlupa City,
1771 Philippines
BE
Amkor ATP3/4 AMKOR ATP3/4
119 North Science Avenue,
Laguna Technopark, Binan, Laguna,
4024 Philippines
BE
Amkor ATT1 AMKOR TECHNOLOGY TAIWAN, INC. (ATT) - T1
No. 1, Kao-Ping Sec, Chung-Feng Road.,
Longtan District, TAOYUAN City 325,
Taiwan R.O.C.
BE
Amkor ATT3 AMKOR TECHNOLOGY TAIWAN, INC. (ATT) - T3
No. 11, Guangfu Road., Hsinchu Industrial Park,
Hukou Township, HSINCHU County 303,
Taiwan R.O.C.
BE
DNP Japan DNP (Dai Nippon printing Co ltd.)
2-2-1 Kami-Fukuoka, Fujimino-shi,
Saitama,356-8507,
Japan
MASK
DPE Italy DPE (Dai Printing Europe)
Via C. Olivetti, 2/A,
I-20041 Agrate,
Italy
MASK
Feiliks Feili Logistics (Shenzhen) CO., Ltd
Zhongbao Logistics Building,
No. 28 Taohua Road, FFTZ,
Shenzhen, Guangdong 518038,
China
WHS
Smartflex Smartflex Technology
37A Tampines Street 92,
Singapore 528886
BE
ST AMK1 STMicroelectronics
5A Serangoon North Avenue 5,
Singapore 554574
DEV
ST AMK6 STMicroelectronics
18 Ang Mo Kio Industrial park 2,
Singapore 569505
WHS
ST33G1M2AM D01 platform Security Target for composition Identification
SMD_ST33G1M2AM_ST_19_002 57/66
ST Bouskoura STMicroelectronics
101 Boulevard des Muriers – BP97,
20180 Bouskoura,
Maroc
BE
WHS
ST Calamba STMicroelectronics
9 Mountain Drive, LISP II, Brgy La mesa,
Calamba,
Philippines 4027
BE
WHS
ST Crolles STMicroelectronics
850 rue Jean Monnet,
38926 Crolles,
France
DEV
MASK
FE
ST Gardanne CMP Georges Charpak
880 Avenue de Mimet,
13541 Gardanne,
France
BE
ST Grenoble STMicroelectronics
12 rue Jules Horowitz, BP 217,
38019 Grenoble Cedex,
France
DEV
ST Ljubljana STMicroelectronics d.o.o. Ljubljana
Tehnoloski park 21,
1000 Ljubljana,
Slovenia
DEV
ST Loyang STMicroelectronics
7 Loyang Drive,
Singapore 508938
WHS
ST Rennes STMicroelectronics
10 rue de Jouanet, ePark,
35700 Rennes,
France
DEV
ST Rousset STMicroelectronics
190 Avenue Célestin Coq, Z.I.,
13106 Rousset Cedex,
France
DEV
EWS
WHS
FE
ST Shenzen STS Microelectronics
16 Tao hua Rd.,
Futian free trade zone,
Shenzhen,
P.R. China 518038
BE
Table 15. Sites list (continued)
Site Address Activities(1)
Identification ST33G1M2AM D01 platform Security Target for composition
58/66 SMD_ST33G1M2AM_ST_19_002
ST Sophia STMicroelectronics
635 route des lucioles,
06560 Valbonne,
France
DEV
ST Toa Payoh STMicroelectronics
629 Lorong 4/6 Toa Payoh,
Singapore 319521
EWS
ST Tunis STMicroelectronics Tunis
Elgazala Technopark, Raoued,
Gouvernorat de l’Ariana, PB21, 2088 cedex, Ariana,
Tunisia
IT
ST Zaventem STMicroelectronics
Green Square, Lambroekstraat 5, Building B, 3d floor,
1831 Diegem/Machelen,
Belgium
DEV
STATS JSCC STATS ChipPAC Semiconductor Jiangyin CO. Ltd
(JSCC)
No. 78 Changshan Road, Jiangyin,
Jiangsu,
China, Postal code: 214437
BE
TSMC F2/F5 TSMC FAB 2-5
121 Park Avenue 3, Hsinchu science park,
Hsinchu 300-77,
Taiwan, ROC
MASK
FE
TSMC F14 TSMC FAB 14
1-1 Nan Ke N. Rd. Tainan science park,
Tainan 741_44,
Taiwan, ROC
MASK
FE
TSMC F8 TSMC FAB 8
25, Li-Hsin Road, Hsinchu Science Park,
Hsinchu 300-78,
Taiwan ROC
MASK
FE
UTL1 UTAC Thai Limited 1
237 Lasalle Road,
Bangna, Bangkok,
10260 Thailand
BE
Table 15. Sites list (continued)
Site Address Activities(1)
ST33G1M2AM D01 platform Security Target for composition Identification
SMD_ST33G1M2AM_ST_19_002 59/66
UTL3 UTAC Thai Limited 3
73 Moo5, Bangsamak,
Bangpakong, Chachoengsao,
24180 Thailand
BE
Winstek WINSTEK STATS ChipPAC (SCT)
No 176-5, 6 Ling, Hualung Chun, Chiung Lin,
307 Hsinchu,
Taiwan
BE
1. DEV = development, FE = front end manudacturing, EWS = electrical wafer sort and pre-perso, BE
= back end manufacturing, MASK = mask manufacturing, WHS = warehouse, IT = Network
infrastructure
Table 15. Sites list (continued)
Site Address Activities(1)
References ST33G1M2AM D01 platform Security Target for composition
60/66 SMD_ST33G1M2AM_ST_19_002
8 References
Table 16. Common Criteria
Component description Reference Version
Common Criteria for Information Technology
Security Evaluation - Part 1: Introduction and
general model, April 2017
CCMB-2017-04-001 R5 3.1 Rev 5
Common Criteria for Information Technology
Security Evaluation - Part 2: Security functional
components, April 2017
CCMB-2017-04-002 R5 3.1 Rev 5
Common Criteria for Information Technology
Security Evaluation - Part 3: Security assurance
components, April 2017
CCMB-2017-04-003 R5 3.1 Rev 5
Table 17. Protection Profile
Component description Reference Version
Eurosmart - Security IC Platform Protection Profile
with Augmentation Packages
BSI-CC-PP-0084-2014 1.0
Table 18. Other standards
Ref Identifier Description
[1] BSI-AIS20/AIS31 A proposal for: Functionality classes for random number
generators,
W. Killmann & W. Schindler
BSI, Version 2.0, 18-09-2011
[2] NIST SP 800-67 NIST SP 800-67, Recommendation for the Triple Data
Encryption Algorithm (TDEA) Block Cipher, revised January
2012, National Institute of Standards and Technology
[3] FIPS PUB 197 FIPS PUB 197, Advanced Encryption Standard (AES), National
Institute of Standards and Technology, U.S. Department of
Commerce, November 2001
[4] ISO/IEC 9796-2 ISO/IEC 9796, Information technology - Security techniques -
Digital signature scheme giving message recovery - Part 2:
Integer factorization based mechanisms, ISO, 2002
[5] NIST SP 800-38A NIST SP 800-38A Recommendation for Block Cipher Modes of
Operation, 2001, with Addendum Recommendation for Block
Cipher Modes of Operation: Three Variants of Ciphertext
Stealing for CBC Mode, October 2010
[6] ISO/IEC 14888 ISO/IEC 14888, Information technology - Security techniques -
Digital signatures with appendix - Part 1: General (1998), Part
2: Identity-based mechanisms (1999), Part 3: Certificate based
mechanisms (2006), ISO
ST33G1M2AM D01 platform Security Target for composition References
SMD_ST33G1M2AM_ST_19_002 61/66
[7] AUG Smartcard Integrated Circuit Platform Augmentations,
Atmel, Hitachi Europe, Infineon Technologies, Philips
Semiconductors,
Version 1.0, March 2002.
[8] IEEE 1363-2000 IEEE 1363-2000, Standard Specifications for Public Key
Cryptography, IEEE, 2000
[9] IEEE 1363a-2004 IEEE 1363a-2004, Standard Specifications for Public Key
Cryptography - Amendment 1:Additional techniques, IEEE,
2004
[10] PKCS #1 V2.1 PKCS #1 V2.1 RSA Cryptography Standard, RSA Laboratories,
June 2002
[11] MOV 97 Alfred J. Menezes, Paul C. van Oorschot and Scott A.
Vanstone, Handbook of Applied Cryptography, CRC Press,
1997
Table 18. Other standards
Ref Identifier Description
Glossary ST33G1M2AM D01 platform Security Target for composition
62/66 SMD_ST33G1M2AM_ST_19_002
Appendix A Glossary
A.1 Terms
Authorised user
A user who may, in accordance with the TSP, perform an operation.
Composite product
Security IC product which includes the Security Integrated Circuit (i.e. the TOE) and the
Embedded Software and is evaluated as composite target of evaluation.
End-consumer
User of the Composite Product in Phase 7.
Integrated Circuit (IC)
Electronic component(s) designed to perform processing and/or memory functions.
IC Dedicated Software
IC proprietary software embedded in a Security IC (also known as IC firmware) and
developed by ST. Such software is required for testing purpose (IC Dedicated Test
Software) but may provide additional services to facilitate usage of the hardware and/or
to provide additional services (IC Dedicated Support Software).
IC Dedicated Test Software
That part of the IC Dedicated Software which is used to test the TOE before TOE
Delivery but which does not provide any functionality thereafter.
IC developer
Institution (or its agent) responsible for the IC development.
IC manufacturer
Institution (or its agent) responsible for the IC manufacturing, testing, and pre-
personalization.
IC packaging manufacturer
Institution (or its agent) responsible for the IC packaging and testing.
Initialisation data
Initialisation Data defined by the TOE Manufacturer to identify the TOE and to keep
track of the Security IC’s production and further life-cycle phases are considered as
belonging to the TSF data. These data are for instance used for traceability and for
TOE identification (identification data)
Object
An entity within the TSC that contains or receives information and upon which subjects
perform operations.
Packaged IC
Security IC embedded in a physical package such as micromodules, DIPs, SOICs or
TQFPs.
Pre-personalization data
Any data supplied by the Card Manufacturer that is injected into the non-volatile
memory by the Integrated Circuits manufacturer (Phase 3). These data are for instance
used for traceability and/or to secure shipment between phases.
ST33G1M2AM D01 platform Security Target for composition Glossary
SMD_ST33G1M2AM_ST_19_002 63/66
Secret
Information that must be known only to authorised users and/or the TSF in order to
enforce a specific SFP.
Security IC
Composition of the TOE, the Security IC Embedded Software, User Data, and the
package.
Security IC Embedded SoftWare (ES)
Software embedded in the Security IC and not developed by the IC designer. The
Security IC Embedded Software is designed in Phase 1 and embedded into the
Security IC in Phase 3.
Security IC embedded software (ES) developer
Institution (or its agent) responsible for the security IC embedded software
development and the specification of IC pre-personalization requirements, if any.
Security attribute
Information associated with subjects, users and/or objects that is used for the
enforcement of the TSP.
Sensitive information
Any information identified as a security relevant element of the TOE such as:
– the application data of the TOE (such as IC pre-personalization requirements, IC
and system specific data),
– the security IC embedded software,
– the IC dedicated software,
– the IC specification, design, development tools and technology.
Smartcard
A card according to ISO 7816 requirements which has a non volatile memory and a
processing unit embedded within it.
Subject
An entity within the TSC that causes operations to be performed.
Test features
All features and functions (implemented by the IC Dedicated Software and/or
hardware) which are designed to be used before TOE Delivery only and delivered as
part of the TOE.
TOE Delivery
The period when the TOE is delivered which is after Phase 3 or Phase 4 in this
Security target.
TSF data
Data created by and for the TOE, that might affect the operation of the TOE.
User
Any entity (human user or external IT entity) outside the TOE that interacts with the
TOE.
User data
All data managed by the Smartcard Embedded Software in the application context.
User data comprise all data in the final Smartcard IC except the TSF data.
Glossary ST33G1M2AM D01 platform Security Target for composition
64/66 SMD_ST33G1M2AM_ST_19_002
A.2 Abbreviations
Table 19. List of abbreviations
Term Meaning
AES Advanced Encryption Standard
AIS Application notes and Interpretation of the Scheme (BSI).
ALU Arithmetical and Logical Unit.
BE Back End manufacturing.
BSI Bundesamt für Sicherheit in der Informationstechnik.
CBC Cipher Block Chaining.
CC Common Criteria Version 3.1. R5.
CPU Central Processing Unit.
CRC Cyclic Redundancy Check.
DCSSI Direction Centrale de la Sécurité des Systèmes d’Information.
DES Data Encryption Standard.
DEV Development.
DIP Dual-In-Line Package.
EAL Evaluation Assurance Level.
ECB Electronic Code Book.
EDES Enhanced DES.
EEPROM Electrically Erasable Programmable Read Only Memory.
ES Security IC Embedded Software.
EWS Electrical Wafer Sort.
FE Front End manufacturing.
FIPS Federal Information Processing Standard.
FTOS Final Test Operating System.
GPIO General Purpose I/O.
I/O Input / Output.
IC Integrated Circuit.
ISO International Standards Organisation.
IT Information Technology.
LPU Library Protection Unit.
MASK Mask manufacturing.
MPU Memory Protection Unit.
NESCRYPT Next Step Cryptography Accelerator.
ST33G1M2AM D01 platform Security Target for composition Glossary
SMD_ST33G1M2AM_ST_19_002 65/66
NFC Near Field Communication.
NIST National Institute of Standards and Technology.
NVM Non Volatile Memory.
OSP Organisational Security Policy.
OST Operating System for Test.
PP Protection Profile.
PUB Publication Series.
RAM Random Access Memory.
RF Radio Frequency.
RF UART Radio Frequency Universal Asynchronous Receiver Transmitter.
ROM Read Only Memory.
SAR Security Assurance Requirement.
SFP Security Function Policy.
SFR Security Functional Requirement.
SIM Subscriber Identity Module.
SOIC Small Outline IC.
SPI Serial Peripheral Interface.
ST Context dependent : STMicroelectronics or Security Target.
SWP Single Wire Protocol.
TOE Target of Evaluation.
TQFP Thin Quad Flat Package.
TRNG True Random Number Generator.
TSC TSF Scope of Control.
TSF TOE Security Functionality.
TSFI TSF Interface.
TSP TOE Security Policy.
TSS TOE Summary Specification.
UID User Identification.
WHS Warehouse.
Table 19. List of abbreviations (continued)
Term Meaning
ST33G1M2AM D01 platform Security Target for composition
66/66 SMD_ST33G1M2AM_ST_19_002
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other
product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2020 STMicroelectronics – All rights reserved