Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Nov 14, 2019 Prepared for: Juniper Networks, Inc. 1133 Innovation Way Sunnyvale, CA 94089 www.juniper.net Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 2 of 89 Abstract This document provides the basis for an evaluation of a specific Target of Evaluation (TOE), Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M. This Security Target (ST) is conformant to the requirements of Collaborative Protection Profile for Network Devices v2.1 [NDcPP], and those for Firewall [FWcPP], Intrusion Prevention Systems [IPS_EP], and VPN Gateway [VPN_EP]. References [CC1] Common Criteria for Information Technology Security Evaluation, Part 1: Introduction and General Model, CCMB-2017-04-001, Version 3.1 Revision 5, April 2017 [CC2] Common Criteria for Information Technology Security Evaluation, Part 2: Security Functional Components, CCMB-2017-04-002, Version 3.1 Revision 5, April 2017 [CC3] Common Criteria for Information Technology Security Evaluation, Part 3: Security Assurance Components, CCMB-2017-04-003, Version 3.1 Revision 5, April 2017 [CC_Add] CC and CEM Addenda, Exact Conformance, Selection-Based SFRs, Optional SFRs, CCDB- 2017-05-xxx, Version 0.5, May 2017 [FWcPP] collaborative Protection Profile for Stateful Traffic Filter Firewalls, Version 2.0+Errata 20180314, dated 14 March 2018 [FWcPP_SD] Supporting Document, Evaluation Activities for Stateful Traffic Filter Firewall cPP, October 2017, version 2.0 [IPS_EP] collaborative Protection Profile for Network Devices/collaborative Protection Profile for Stateful Traffic Filter Firewalls Extended Package (EP) for Intrusion Prevention Systems (IPS), version 2.11, dated 15 June 2017 [NDcPP] Collaborative Protection Profile for Network Devices, version 2.1 dated 24 September 2018 [SD] Supporting Document, Evaluation Activities for Network Device cPP, September 2018, version 2.1 [VPN_EP] Network Device Collaborative Protection Profile (NDcPP)/Stateful Traffic Filter Firewall Collaborative Protection Profile (FWcPP) Extended Package VPN Gateway, version 2.1, dated 08 March 2017 Product Guide References [ECG1] Junos OS Common Criteria Guide for SRX300, SRX320, SRX340, SRX345 and SRX550M Devices, Release 19.2R1, Date 2019-10-02 [IDPGuide] Junos OS Intrusion Detection and Prevention Feature Guide for Security Devices, 13- Oct-19 [VPNGuide] Junos OS VPN Feature Guide for Security Devices, 01-Oct-19 [CLIGuide] Junos OS CLI User Guide, 25-Sep-19 [InsGuide] Junos OS Installation and Upgrade Guide, 05-Aug-19 [FWGuide] Junos OS Routing Policies, Firewall Filters, and Traffic Policers Feature Guide, 11-Oct-19 Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 3 of 89 Table of Contents 1 Introduction ....................................................................................................................................6 1.1 ST reference............................................................................................................................6 1.2 TOE Reference.........................................................................................................................6 1.3 About this document ..............................................................................................................6 1.4 Document Conventions ..........................................................................................................6 1.5 TOE Overview..........................................................................................................................7 1.6 TOE Description.......................................................................................................................7 1.6.1 Overview .........................................................................................................................7 1.6.2 Physical boundary...........................................................................................................8 1.6.3 Logical Boundary...........................................................................................................10 1.6.4 Non-TOE hardware/software/firmware .......................................................................11 1.6.5 Summary of out scope items ........................................................................................12 2 Conformance Claim.......................................................................................................................13 2.1 CC Conformance Claim .........................................................................................................13 2.2 PP Conformance claim..........................................................................................................13 2.3 Technical Decisions...............................................................................................................14 3 Security Problem Definition..........................................................................................................18 3.1 Threats ..................................................................................................................................18 3.2 Assumptions..........................................................................................................................20 3.3 Organizational Security Policies............................................................................................22 4 Security Objectives........................................................................................................................23 4.1 Security Objectives for the TOE ............................................................................................23 4.2 Security Objectives for the Operational Environment..........................................................25 4.3 Security Objectives rationale ................................................................................................26 5 Security Functional Requirements................................................................................................27 5.1 Security Audit (FAU)..............................................................................................................27 5.1.1 Security Audit Data generation (FAU_GEN)..................................................................27 5.1.2 Security audit event storage (Extended – FAU_STG_EXT)............................................31 5.2 Cryptographic Support (FCS).................................................................................................32 5.2.1 Cryptographic Key Management (FCS_CKM)................................................................32 5.2.2 Cryptographic Operation (FCS_COP) ............................................................................33 5.2.3 Random Bit Generation (Extended – FCS_RBG_EXT)....................................................34 5.2.4 Cryptographic Protocols (Extended – FCS_ IPSEC_EXT & FCS_SSHS_EXT SSH Protocol34 5.3 Identification and Authentication (FIA) ................................................................................36 5.3.1 Authentication Failure Management (FIA_AFL) ...........................................................36 5.3.2 Password Management (Extended – FIA_PMG_EXT)...................................................37 Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 4 of 89 5.3.3 User Identification and Authentication (Extended – FIA_UIA_EXT) .............................37 5.3.4 User authentication (FIA_UAU) (Extended – FIA_UAU_EXT)........................................37 5.3.5 Authentication using X.509 certificates (Extended – FIA_X509_EXT)...........................38 5.4 Security Management (FMT) ................................................................................................39 5.4.1 Management of functions in TSF (FMT_MOF)..............................................................39 5.4.2 Management of TSF Data (FMT_MTD) .........................................................................39 5.4.3 Specification of Management Functions (FMT_SMF)...................................................40 5.4.4 Security management roles (FMT_SMR) ......................................................................41 5.5 Protection of the TSF (FPT) ...................................................................................................41 5.5.1 Protection of TSF Data (Extended – FPT_SKP_EXT) ......................................................41 5.5.2 Protection of Administrator Passwords (Extended – FPT_APW_EXT)..........................41 5.5.3 TSF testing (Extended – FPT_TST_EXT).........................................................................41 5.5.4 Trusted Update (FPT_TUD_EXT) ...................................................................................42 5.5.5 Time stamps (Extended – FPT_STM_EXT)) ...................................................................42 5.5.6 Self-test Failures (FPT_FLS) ...........................................................................................42 5.6 TOE Access (FTA)...................................................................................................................43 5.6.1 TSF-initiated Session Locking (Extended – FTA_SSL_EXT) ............................................43 5.6.2 Session locking and termination (FTA_SSL) ..................................................................43 5.6.3 TOE access banners (FTA_TAB).....................................................................................43 5.7 Trusted path/channels (FTP).................................................................................................43 5.7.1 Trusted Channel (FTP_ITC)............................................................................................43 5.7.2 Trusted Path (FTP_TRP).................................................................................................44 5.8 User Data Protection (FDP)...................................................................................................44 5.8.1 Residual information protection (FDP_RIP)..................................................................44 5.9 Packet Filtering (FPF) ............................................................................................................44 5.9.1 Packet Filtering Rules (FPF_RUL_EXT)...........................................................................44 5.10 Firewall (FFW) .......................................................................................................................45 5.10.1 Stateful Traffic Filter Firewall (FFW_RUL_EXT).............................................................45 5.11 Intrusion Prevention (IPS).....................................................................................................47 5.11.1 Network Traffic Analysis (IPS_NTA_EXT) ......................................................................47 5.11.2 IPS IP Blocking (IPS_IPB_EXT)........................................................................................48 5.11.3 Signature-Based IPS Functionality (IPS_SBD_EXT)........................................................48 5.11.4 Anomaly-Based IPS Functionality (IPS_ABD_EXT) ........................................................49 6 Security Assurance Requirements ................................................................................................51 7 TOE Summary Specification..........................................................................................................52 7.1 Protected communications...................................................................................................52 7.1.1 Algorithms and zeroization...........................................................................................52 7.1.2 Random Bit Generation ................................................................................................61 Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 5 of 89 7.1.3 SSH ................................................................................................................................62 7.1.4 IPsec ..............................................................................................................................65 7.2 Administrator Authentication...............................................................................................68 7.3 Correct Operation.................................................................................................................70 7.4 Trusted Update .....................................................................................................................70 7.5 Audit......................................................................................................................................71 7.6 Management.........................................................................................................................74 7.7 User Data Protection.............................................................................................................76 7.8 Packet Filtering/Stateful Traffic ............................................................................................76 7.9 Intrusion Prevention System.................................................................................................80 8 Rationales......................................................................................................................................84 8.1 SFR dependency analysis ......................................................................................................84 9 Glossary.........................................................................................................................................87 10 TOE Network Interface Options................................................................................................89 10.1 Mini PIMs ..............................................................................................................................89 10.2 GPIM / XPIM..........................................................................................................................89 Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 6 of 89 1 Introduction 1. This section identifies the Security Target (ST), Target of Evaluation (TOE), Security Target organization, document conventions, and terminology. It also includes an overview of the evaluated products. 1.1 ST reference ST Title Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345- DUAL-AC and SRX550M Series ST Revision 3.7 ST Draft Date November 14, 2019 Author Juniper Networks, Inc. cPP/EP Conformance [NDcPP], [FWcPP], [VPN_EP], [IPS_EP] 1.2 TOE Reference TOE Title Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M 1.3 About this document 2. This Security Target follows the following format: Section Title Description 1 Introduction Provides an overview of the TOE and defines the hardware and firmware that make up the TOE as well as the physical and logical boundaries of the TOE 2 Conformance Claims Lists evaluation conformance to Common Criteria versions, Protection Profiles, or Packages where applicable 3 Security Problem Definition Specifies the threats, assumptions and organizational security policies that affect the TOE 4 Security Objectives Defines the security objectives for the TOE/operational environment and provides a rationale to demonstrate that the security objectives satisfy the threats 5 Security Functional Requirements Contains the functional requirements for this TOE 6 Security Assurance Requirements Contains the assurance requirements for this TOE 7 TOE Summary Specification Identifies the IT security functions provided by the TOE and also identifies the assurance measures targeted to meet the assurance requirements Table 1 Document Organization 1.4 Document Conventions 3. This document follows the same conventions as those applied in [NDcPP] in the completion of operations on Security Functional Requirements, namely: • Unaltered SFRs are stated in the form used in [CC2] or their extended component definition (ECD); • Refinement made in the ST: the refinement text is indicated with bold text and strikethroughs; • Selection completed in the ST: the selection values are indicated with underlined text Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 7 of 89 e.g. “[selection: disclosure, modification, loss of use]” in [CC2] or an ECD might become “disclosure” (completion; • Assignment completed in the ST: indicated with italicized text; • Assignment completed within a selection in the ST: the completed assignment text is indicated with italicized and underlined text e.g. “[selection: change_default, query, modify, delete, [assignment: other operations]]” in [CC2] or an ECD might become “change_default, select_tag” (completion of both selection and assignment); • Iteration: indicated by adding a string starting with “/” (e.g. “FCS_COP.1/Hash”). 1.5 TOE Overview 4. The Target of Evaluation (TOE) is Juniper Networks, Inc. Junos OS 19.2R1 Services Gateway appliances: • SRX300 • SRX320 • SRX340 • SRX345 • SRX345-DUAL-AC • SRX550M 5. The Services Gateway appliances primarily support the definition of, and enforce, information flow policies among network nodes. The Services Gateway appliances provide for stateful inspection of every packet that traverses the network and provide central management to manage the network security policy. All information flow from one network node to another passes through an instance of the TOE. Information flow is controlled on the basis of network node addresses, protocol, type of access requested, and services requested. In support of the information flow security functions, the TOE ensures that security-relevant activity is audited, that their own functions are protected from potential attacks, and provides the security tools to manage all of the security functions. The TOE provides multi-site virtual private network (VPN) gateway functionality. The TOE also implements Intrusion Prevention System functionality, capable of monitoring information flows to detect potential attacks based on pre-defined attack signature and anomaly characteristics in the traffic. 6. All the SRX Services Gateway appliance models run the same Juniper Networks Junos operating system (Junos OS), Junos OS 19.2R1. 1.6 TOE Description 1.6.1 Overview 7. Each Juniper Networks SRX Services Gateway appliance is a security system that supports a variety of high-speed interfaces (up to 40 Gbps for firewall and 20 Gbps for IPS) for medium/large networks and network applications. Juniper Networks routers share common Junos firmware, features, and technology for compatibility across platforms. 8. The appliances are physically self-contained, housing the software, firmware and hardware necessary to perform all router functions. The hardware has two components: the Services Gateway appliance itself and various PIC/PIMs, which allow the appliances to communicate with Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 8 of 89 the different types of networks that may be required within the environment where the Services Gateway appliances are used. 9. Each instance of the TOE consists of the following major architectural components: • The Routing Engine (RE) runs the Junos firmware and provides Layer 3 routing services and network management for all operations necessary for the configuration and operation of the TOE and controls the flow of information through the TOE, including Network Address Translation (NAT) and all operations necessary for the encryption/decryption of packets for secure communication via the IPSec protocol. • The Packet Forwarding Engine (PFE) provides all operations necessary for transit packet forwarding. 10. The Routing Engine and Packet Forwarding Engine perform their primary tasks independently, while constantly communicating through a high-speed internal link. This arrangement provides streamlined forwarding and routing control and the capability to run Internet-scale networks at high speeds. 11. The Services Gateway appliances support numerous routing standards for flexibility and scalability as well as IETF IPSec protocols. These functions can all be managed through the Junos firmware, either from a connected terminal console or via a network connection. Network management can be secured using IPsec and SSH protocols. All management, whether from a user connecting to a terminal or from the network, requires successful authentication. In the evaluated deployment Network management is secured using the SSH protocol, which can be tunnelled over IPsec. 12. The TOE supports intrusion detection and prevention functionality, which allows it to detect and react to potential attacks in real time. The detection component of the IPS can be based on attack signatures which specify the characteristics of the potentially malicious traffic based on a variety of packet headers payload data attributes. Anomaly detection based on deviation of the monitored traffic from expected values is also supported. 13. Services Gateway appliances accomplish routing through a process called a Virtual Router (VR). A security device divides its routing component into two or more VRs with each VR maintaining its own list of known networks in the form of a routing table, routing logic, and associated security zones. 14. In the evaluated deployment the TOE is managed and configured via Command Line Interface, either via a directly connected console or using SSH connections (over IPsec). 1.6.2 Physical boundary 15. The physical boundary of the TOE is the entire chassis of the Services Gateway appliance, and so includes both the hardware and firmware of the network device. The TOE is the Junos OS 19.2R1 firmware running on the appliance chassis listed in Table 2 below. This includes the firmware implementing the Routing Engine and the ASICs implementing the Packet Forwarding Engine). Hence the TOE is contained within the physical boundary of the specified appliance chassis. The install package for the SRX300/SRX320/SRX340/SRX345/SRX345-DUAL- AC/SRX550M appliance is “junos-srxsme-19.2R1.8.tgz”. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 9 of 89 Figure 1 TOE Boundary 16. The TOE interfaces are comprised of the following: i. Network interfaces which pass traffic ii. Management interface through which handle administrative actions. Model Network Ports1 Firmware SRX300 • Six Gigabit Ethernet LAN ports • Two 1G SFP ports Junos OS 19.2R1 SRX320 • Two Mini PIM slots • Six Gigabit Ethernet LAN ports • Two 1G SFP ports SRX340 • Four Mini PIM slots • Eight Gigabit Ethernet LAN ports • Eight 1G SFP ports • One Management RJ45 port SRX345 • Four Mini PIM slots • Eight Gigabit Ethernet LAN ports • Eight 1G SFP ports • One Management RJ45 port SRX-345- DUAL-AC • Four Mini PIM Slots • Eight Gigabit Ethernet LAN ports • Eight 1G SFP ports • One Management RJ45 port SRX550M • Two Mini PIM slots • Six GPIM slots (slot 3 supports 10 Gigabit XPIMs, slot 6 supports 20 Gigabit XPIMs • Six Gigabit Ethernet LAN ports • Four 1G SFP ports Table 2 TOE Physical Boundary Details 17. The guidance document included as part of the TOE is [ECG1], [IDPGuide], [VPNGuide], [CLIGuide], [InsGuide], and [FWGuide] 1 More details of the supported Network Ports can be found in in Section 10. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 10 of 89 1.6.3 Logical Boundary 18. The logical boundary of the TOE includes the following security functionality: Security Functionality Description Protected Communications The TOE provides an SSH server to support protected communications for administrators to establish secure sessions and to connect to external syslog servers. The TOE also supports IPsec connections to provide multi- site virtual private network (VPN) gateway functionality and also as a tunnel for remote administrate SSH connections. The TOE requires that applications exchanging information with it are successfully authenticated prior to any exchange (i.e. applications connecting over SSH and IPsec). Telnet, File Transfer Protocol (FTP), and Secure Socket Layer (SSL) are out of scope. The TOE includes cryptographic modules that provide the underlying cryptographic services, including key management and protection of stored keys, algorithms, random bit generation and crypto-administration. The cryptographic modules provide confidentiality and integrity services for authentication and for protecting communications with adjacent systems. Administrator Authentication Administrative users must provide unique identification and authentication data before any administrative access to the system is granted. Authentication data entered and stored on the TOE is protected. The TOE can be configured to terminate interactive user sessions and to present an access banner with warning messages prior to authentication. Correct Operation The TOE provides for cryptographic and non-cryptographic self-tests, and is capable of automated recovery from failure states. Trusted Update The administrator can initiate update of the TOE firmware. The integrity of any firmware updates is verified prior to installation of the updated firmware. Audit Junos auditable events are stored in the syslog files on the appliance, and can be sent to an external log server (via Netconf over SSH). Auditable events include start-up and shutdown of the audit functions, authentication events, service requests, IPS events, as well as the events listed in Table 4 and Table 5. Audit records include the date and time, event category, event type, username, and the outcome of the event (success or failure). Local syslog storage limits are configurable and are monitored. If the storage limits are reached the oldest logs will be overwritten. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 11 of 89 Security Functionality Description Management The TOE provides a Security Administrator role that is authorized and responsible for: • the configuration and maintenance of cryptographic elements related to the establishment of secure connections to and from the evaluated product • the regular review of all audit data; • initiation of trusted update function; • administration of VPN, IPS and Firewall functionality; • all administrative tasks (e.g., creating the security policy). The devices are managed through a Command Line Interface (CLI). The CLI is accessible through local (serial) console connection or remote administrative (SSH) session. Packet Filtering/Stateful Traffic Filtering The TOE provides stateful network traffic filtering based on examination of network packets and the application of information flow rules. Intrusion Prevention The TOE can be configured to analyze IP-based network traffic forwarded to the TOE’s interfaces, and detect violations of administratively-defined IPS policies. The TOE is capable of initiating a proactive response to terminate/interrupt an active potential threat, and to initiate a response in real time that would cause interruption of the suspicious traffic flow. User Data Protection/ Information Flow Control The TOE is designed to forward network packets (i.e., information flows) from source network entities to destination network entities based on available routing information. This information is either provided directly by TOE users or indirectly from other network entities (outside the TOE) configured by the TOE users. The TOE has the capability to regulate the information flow across its interfaces; traffic filters can be set in accordance with the presumed identity of the source, the identity of the destination, the transport layer protocol, the source service identifier, and the destination service identifier (TCP or UDP port number). 1.6.4 Non-TOE hardware/software/firmware 19. The SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M series models of the TOE require SFPs/PIMs to operate and communicate with the connected network. These are detailed for each TOE appliance in Section 10. 20. The TOE relies on the provision of the following items in the network environment: • Syslog server supporting SSHv2 connections to send audit logs; • SSHv2 client for remote administration; • Serial connection client for local administration; • IPsec peer. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 12 of 89 1.6.5 Summary of out scope items • Use of telnet, since it violates the Trusted Path requirement set (see Section 5.7.2) • Use of FTP, since it violates the Trusted Path requirement set (see Section 5.7.2) • Use of SNMP, since it violates the Trusted Path requirement set (see Section 5.7.2) • Use of SSL, including management via J-Web, JUNOScript and JUNOScope, since it violates the Trusted Path requirement set (see Section 5.7.2) • Use of CLI account super-user and junos root account. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 13 of 89 2 Conformance Claim 2.1 CC Conformance Claim 21. This Security Target conforms to the requirements of Common Criteria v3.1, Revision 5 and is Part 2 extended and Part 3 conformant. 2.2 PP Conformance claim 22. This Security Target claims Exact Conformance to [NDcPP] (v2.1) and [FWcPP] (v2.0E). Exact conformance is defined in [NDcPP] section 2 and in [CC_Add]. In the rules of specified in [CC_Add] it is possible to claim exact conformance to more than one Protection Profile, providing they both require exact conformance. This is the case for both [NDcPP] and [FWcPP]. 23. In lieu of any available PP-modules facilitating the expression of functionality provided by this class of network device, this Security Target conforms to the NIAP Extended Packages [IPS_EP] (v2.11) and [VPN_EP] (v2.1). This approach is supported by the fact that [VPN_EP] and [IPS_EP] also require exact conformance, as is required by [CC_Add] when adding requirements from a Package or PP-Module (in this case [VPN_EP] and [IPS_EP]) to Base-PPs (in this case [NDcPP] and [FWcPP]). 24. The Security Problem definition in this Security Target is consistent with the security problem definitions detailed in the collaborative Protection Profiles and Extended Packages to which this ST claims conformance, namely: • [NDcPP] Section 4 • [FWcPP] Section 3 • [IPS_EP] Section 2 • [VPN_EP] Section 3. 25. The statement of the Security Problem Definition in this ST is the superset of the threats, organizational security policies and assumptions from the collaborative Protection Profiles and Extended Packages. In creating this superset, some assumptions made in the [NDcPP] are restated as threats to be addressed by functionality specified in [FWcPP]. An additional assumption is introduced through compliance to [VPN_EP]. The addition of this assumption (from the point of view of conformance to [NDcPP], [FWcPP] and [IPS_EP]) is permissible for strict conformance2 because A.CONNECTIONS does not mitigate a threat TOE nor fulfil an OSP meant to be addressed by security objectives for the TOE. Hence, this SPD statement is considered to be conformant to the collaborative Protection Profiles and Extended Packages claimed. 26. Similarly, the statement of security objectives in this ST is consistent with the statement of security objectives detailed in the collaborative Protection Profiles and Extended Packages to which this ST claims conformance, namely: • The prose in [NDcPP] Section 3 • The prose in [FWcPP] Section 3 • [IPS_EP] Section 3 • [VPN_EP] Section 4. 2 Exact Conformance, which doesn’t say anything about modification of the SPD, is based on Strict Conformance Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 14 of 89 27. Again, the statement of the Security Objectives in this ST is the superset of the security objectives from the collaborative Protection Profiles and Extended Packages. In creating this superset, the objectives for the operational environment OE.NO_THRU_TRAFFIC_PROTECTION and OE.RESIDUAL_INFORMATION defined in [NDcPP] are omitted, as they are not relevant to this TOE; being addressed by objectives for the TOE introduced through conformance to [FWcPP]. Hence, the statement of security objectives in this ST is considered to be conformant to the collaborative Protection Profiles and Extended Packages claimed 28. The statement of requirements in this ST is consistent with the statement of requirements (functional and assurance) detailed in • [NDcPP] Sections 6 & 7 • [FWcPP] Sections 5 & 6 • [IPS_EP] Section 4 & 6 • [VPN_EP] Section 5. 29. All Security Functional Requirements specified in [NDcPP] Section 6, together with the relevant selection-based requirements from Appendix B are included in this ST. 30. This statement of SFRs is augmented with SFRs specified in (at least one of) [NDcPP] Appendix A (Optional requirements), [FWcPP] Section 5 and Appendices A & B, [IPS_EP] Section 4 and [VPN_EP] Section 5 and Appendices A & B. 31. All extended requirements in this ST are taken from (at least one of) [NDcPP] Appendix C, [FWcPP] Appendix C, [IPS_EP] Section 4 and [VPN_EP] Section 5. 32. The Security Assurance Requirements specified in this ST are the superset of those defined in: • [NDcPP] Section 7 • [FWcPP] Sections 6 • [IPS_EP] Section 6 • [VPN_EP] Section 5.4. 33. The distributed TOE deployment aspects described in [NDcPP] are not applicable as this TOE is satisfied by each model of the TOE in isolation. 2.3 Technical Decisions 34. In line with Labgram #105, this section identifies all NIAP Technical Decisions that are applicable to this TOE. ITEM TITLE REFERENCE PUBLICATI ON DATE Rele vant to ST TD0453 NIT Technical Decision for Clarify authentication methods SSH clients can use to authenticate SSH servers FCS_SSHC_EXT.1.9, ND SD v2.1 2019.09.16 No TD0452 NIT Technical Decision for FCS_(D)TLSC_EXT.X.2 IP addresses in reference identifiers FAU_GEN.1, ND SD v2.1 2019.09.16 No Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 15 of 89 ITEM TITLE REFERENCE PUBLICATI ON DATE Rele vant to ST TD0451 NIT Technical Decision for ITT Comm UUID Reference Identifier FCS_TLSS_EXT.1.2 and FCS_TLSS_EXT.2.2 2019.09.16 No TD0450 NIT Technical Decision for RSA-based ciphers and the Server Key Exchange message FCS_TLSS_EXT.*.3, FCS_DTLSS_EXT.*.4, ND SD v2.1 2019.09.16 No TD0449 NIT Technical Decision for Identification of usage of cryptographic schemes FCS_CKM.2, ND SD v2.1 2019.09.16 Yes TD0448 NIT Technical Decision for Documenting Diffie-Hellman 14 groups FCS_CKM.2 2019.09.16 Yes TD0447 NIT Technical Decision for Using 'diffie- hellman-group-exchange-sha256' in FCS_SSHC/S_EXT.1.7 FCS_SSHC_EXT.1.7, FCS_SSHS_EXT.1.7 2019.09.16 Yes TD0436 IPsec protocol ESP algorithms FCS_IPSEC_EXT.1.4 2019.07.19 Yes TD0425 NIT Technical Decision for Cut-and- paste Error for Guidance AA FTA_SSL.3 2019.05.31 Yes TD0424 NIT Technical Decision for NDcPP v2.1 Clarification - FCS_SSHC/S_EXT1.5 FCS_SSHC_EXT.1.5, FCS_SSHS_EXT.1.5 2019.05.31 Yes TD0423 NIT Technical Decision for Clarification about application of RfI#201726rev2 FTP_ITC.1, FTP_TRP.1/Admin, or FPT_ITT.1 2019.05.31 Yes TD0412 NIT Technical Decision for FCS_SSHS_EXT.1.5 SFR and AA discrepancy FCS_SSHS_EXT.1.5 2019.03.22 Yes TD0411 NIT Technical Decision for FCS_SSHC_EXT.1.5, Test 1 - Server and client side seem to be confused FCS_SSHC_EXT.1.5 2019.03.22 No TD0410 NIT technical decision for Redundant assurance activities associated with FAU_GEN.1 FAU_GEN.1 2019.03.22 Yes TD0409 NIT decision for Applicability of FIA_AFL.1 to key-based SSH authentication FIA_AFL.1 2019.03.22 Yes TD0408 NIT Technical Decision for local vs. remote administrator accounts FIA_AFL.1, FIA_UAU_EXT.2, FMT_SMF.1 2019.03.22 Yes TD0407 NIT Technical Decision for handling Certification of Cloud Deployments N/A 2019.03.22 No TD0402 NIT Technical Decision for RSA-based FCS_CKM.2 Selection FCS_CKM.2 2019.02.24 Yes TD0401 NIT Technical Decision for Reliance on external servers to meet SFRs FTP_ITC.1 2019.02.24 Yes TD0400 NIT Technical Decision for FCS_CKM.2 and elliptic curve-based key establishment FCS_CKM.1, FCS_CKM.2 2019.02.24 Yes Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 16 of 89 ITEM TITLE REFERENCE PUBLICATI ON DATE Rele vant to ST TD0399 NIT Technical Decision for Manual installation of CRL (FIA_X509_EXT.2) FIA_X509_EXT.2 2019.02.24 Yes TD0398 NIT Technical Decision for FCS_SSH*EXT.1.1 RFCs for AES-CTR FCS_SSHC_EXT.1.1, FCS_SSHS_EXT.1.1 2019.02.24 Yes TD0397 NIT Technical Decision for Fixing AES- CTR Mode Tests FCS_COP.1/ DataEncryption 2019.02.24 Yes TD0396 NIT Technical Decision for FCS_TLSC_EXT.1.1, Test 2 FCS_DTLSC_EXT.1.1, FCS_DTLSC_EXT.2.1, FCS_TLSC_EXT.1.1, FCS_TLSC_EXT.2.1 2019.02.24 No TD0395 NIT Technical Decision for Different Handling of TLS1.1 and TLS1.2 FCS_TLSS_EXT.2.4, FCS_TLSS_EXT.2.5 2019.02.24 No TD0394 NIT Technical Decision for Audit of Management Activities related to Cryptographic Keys FAU_GEN.1 2019.02.24 Yes TD0356 OE.CONNECTIONS added to VPN GW v2.1 N/A 2018.09.20 Yes TD0343 NIT Technical Decision for Updating FCS_IPSEC_EXT.1.14 Tests FCS_IPSEC_EXT.1.14 2018.08.02 Yes TD0340 NIT Technical Decision for Handling of the basicConstraints extension in CA and leaf certificates FIA_X509_EXT.1.1/Rev, item 3 2018.08.02 Yes TD0339 NIT Technical Decision for Making password-based authentication optional in FCS_SSHS_EXT.1.2 FCS_SSHS_EXT.1.2 2018.08.02 Yes TD0337 NIT Technical Decision for Selections in FCS_SSH*_EXT.1.6 FCS_SSHS_EXT.1 2018.08.02 Yes TD0335 NIT Technical Decision for FCS_DTLS Mandatory Cipher Suites FCS_DTLSC_EXT.1.1, FCS_DTLSC_EXT.2.1, FCS_DTLSS_EXT.1.1, FCS_DTLSS_EXT.2.1, FCS_TLSC_EXT.1.1, FCS_TLSC_EXT.2.1, FCS_TLSS_EXT.1.1, FCS_TLSS_EXT.2.1 2018.08.01 No TD0333 NIT Technical Decision for Applicability of FIA_X509_EXT.3 FIA_X509_EXT.3 2018.08.01 Yes TD0329 IPSEC X.509 Authentication Requirements FIA_X509_EXT.4, FCS_IPSEC_EXT.1.14 EP_VPN_GW_V2.1 2018.05.31 Yes TD0325 Inline mode for Signature-based IPS policies IPS_SBD_EXT.1.5 2018.05.21 Yes TD0321 Protection of NTP communications FTP_ITC.1, FPT_STM_EXT.1 2018.05.21 Yes TD0319 Updates to FMT_SMF.1 in VPN Gateway EP FMT_SMF.1 EP_VPN_GW_V2.1 2018.04.23 Yes Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 17 of 89 ITEM TITLE REFERENCE PUBLICATI ON DATE Rele vant to ST TD0317 FMT_MOF.1/Services and FMT_MTD.1/CryptoKeys FMT_MOF.1/Services, FMT_MTD.1/CryptoKeys EP_VPN_GW_V2.1 2018.04.23 Yes TD0316 Update to FPT_TST_EXT.2.1 FPT_TST_EXT.2.1, FPT_TST_EXT.3.1 EP_VPN_GW_V2.1 2018.04.20 Yes TD0307 Modification of FTP_ITC_EXT.1.1 FTP_ITC_EXT.1.1, FTP_ITC.1.1 EP_VPN_GW_V2.1 2018.04.18 Yes TD0291 NIT technical decision for DH14 and FCS_CKM.1 FCS_CKM.1.1 2018.02.03 Yes TD0259 NIT Technical Decision for Support for X509 ssh rsa authentication IAW RFC 6187 FCS_SSHC_EXT.1.5, FCS_SSHS_EXT.1.5 2017.11.13 No TD0248 FAU_GEN.1 Guidance Activity EP_VPN_GW_V2.1, FAU_GEN.1 2017.10.20 n/a to ST TD0242 FPF_RUL_EXT.1.7, Test 3 - Logging Dropped Packets EP_VPN_GW_V2.1, FPF_RUL_EXT.1.7 2017.11.08 n/a to ST TD0209 Additional DH Group added as selection for IKE Protocols EP_VPN_GW_V2.1, FCS_IPSEC_EXT.1.11 2017.06.09 Yes TD0179 Management Capabilities in VPN GW EP 2.1 EP_VPN_GW_V2.1, FMT_SMF.1.1 2017.04.11 Yes Table 3 Applicable NIAP Technical Decisions 35. All other NIAP Technical Decisions fall into one of the following categories and hence are not applicable to this TOE: • Relates to earlier version of cPPs/EPs claimed for this TOE. This TD has been superseded by cPPs/EPs (and associated SDs) released after this TD • Relates to cPP/EP that is not claimed for this TOE Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 18 of 89 3 Security Problem Definition 36. As this TOE is not distributed, none of the threats/assumptions/OSPs relating to distributed TOEs are specified for this TOE. 3.1 Threats 37. The following threats for this TOE are as defined in [NDcPP] Section 4.1, which are also stated in [FWcPP], with editorial and terminology changes to reflect focus on firewall rather than general purpose network devices. Namely: • T.UNAUTHORIZED_ADMINISTRATOR_ACCESS Threat agents may attempt to gain Administrator access to the network device by nefarious means such as masquerading as an Administrator to the device, masquerading as the device to an Administrator, replaying an administrative session (in its entirety, or selected portions), or performing man-in-the-middle attacks, which would provide access to the administrative session, or sessions between network devices. Successfully gaining Administrator access allows malicious actions that compromise the security functionality of the device and the network on which it resides. • T.WEAK_CRYPTOGRAPHY Threat agents may exploit weak cryptographic algorithms or perform a cryptographic exhaust against the key space. Poorly chosen encryption algorithms, modes, and key sizes will allow attackers to compromise the algorithms, or brute force exhaust the key space and give them unauthorized access allowing them to read, manipulate and/or control the traffic with minimal effort. • T.UNTRUSTED_COMMUNICATION_CHANNELS Threat agents may attempt to target network devices that do not use standardized secure tunnelling protocols to protect the critical network traffic. Attackers may take advantage of poorly designed protocols or poor key management to successfully perform man-in-the- middle attacks, replay attacks, etc. Successful attacks will result in loss of confidentiality and integrity of the critical network traffic, and potentially could lead to a compromise of the network device itself. • T.WEAK_AUTHENTICATION_ENDPOINTS Threat agents may take advantage of secure protocols that use weak methods to authenticate the endpoints – e.g. a shared password that is guessable or transported as plaintext. The consequences are the same as a poorly designed protocol, the attacker could masquerade as the Administrator or another device, and the attacker could insert themselves into the network stream and perform a man-in-the-middle attack. The result is the critical network traffic is exposed and there could be a loss of confidentiality and integrity, and potentially the network device itself could be compromised. • T.UPDATE_COMPROMISE Threat agents may attempt to provide a compromised update of the software or firmware which undermines the security functionality of the device. Non-validated updates or updates validated using non-secure or weak cryptography leave the update firmware vulnerable to surreptitious alteration. • T.UNDETECTED_ACTIVITY Threat agents may attempt to access, change, and/or modify the security functionality of the network device without Administrator awareness. This could result in the attacker finding an Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 19 of 89 avenue (e.g., misconfiguration, flaw in the product) to compromise the device and the Administrator would have no knowledge that the device has been compromised. • T.SECURITY_FUNCTIONALITY_COMPROMISE Threat agents may compromise credentials and device data enabling continued access to the network device and its critical data. The compromise of credentials includes replacing existing credentials with an attacker’s credentials, modifying existing credentials, or obtaining the Administrator or device credentials for use by the attacker. • T.PASSWORD_CRACKING Threat agents may be able to take advantage of weak administrative passwords to gain privileged access to the device. Having privileged access to the device provides the attacker unfettered access to the network traffic and may allow them to take advantage of any trust relationships with other network devices. • T.SECURITY_FUNCTIONALITY_FAILURE A component of the network device may fail during start-up or during operations causing a compromise or failure in the security functionality of the network device, leaving the device susceptible to attackers. 38. The following threats additional threats specified in [FWcPP], [IPS_EP] and [VPN_EP] are also detailed for this TOE: • T.NETWORK_DISCLOSURE An attacker may attempt to “map” a subnet to determine the machines that reside on the network, and obtaining the IP addresses of machines, as well as the services (ports) those machines are offering. This information could be used to mount attacks to those machines via the services that are exported. • T. NETWORK_ACCESS With knowledge of the services that are exported by machines on a subnet, an attacker may attempt to exploit those services by mounting attacks against those services. • T.NETWORK_MISUSE An attacker may attempt to use services that are exported by machines in a way that is unintended by a site’s security policies. For example, an attacker might be able to use a service to “anonymize” the attacker’s machine as they mount attacks against others. 39. The following threat specified in [FWcPP] only is also detailed for this TOE: • T.MALICIOUS_TRAFFIC A stateful traffic filtering firewall also provides protections against malicious or malformed packets. It will protect against attacks like modification of connection state information and replay attacks. These attacks could cause the firewall, or the devices it protects, to grant unauthorized access or even create a Denial of Service. 40. The following threat specified in [IPS_EP] only is detailed for this TOE: • T.NETWORK_DOS Attacks against services inside a protected network, or indirectly by virtue of access to malicious agents from within a protected network, might lead to denial of services otherwise available within a protected network. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 20 of 89 Resource exhaustion may occur in the event of co-ordinate service request flooding from a small number of sources. 41. The following threat specified in [VPN_EP] only is detailed for this TOE: • T.DATA_INTEGRITY Devices on a protected network may be exposed to threats presented by devices located outside the protected network, which may attempt to modify the data without authorization. If known malicious external devices are able to communicate with devices on the protected network or if devices on the protected network can establish communications with those external devices then the data contained within the communications may be susceptible to a loss of integrity. • T.HIJACKED_SESSION There may be an instance where a remote client’s session is hijacked due to session activity. This could be accomplished because a user has walked away from the machine that was used to establish the session. • T.REPLAY_ATTACK 42. If an unauthorized individual successfully gains access to the system, the adversary may have the opportunity to conduct a “replay” attack. This method of attack allows the individual to capture packets traversing throughout the network and send the packets at a later time, possibly unknown by the intended receiver. Traffic is subject to replay if it meets the following conditions: o Cleartext: an attacker with the ability to view unencrypted traffic can identify an appropriate segment of the communications to replay as well in order to cause the desired outcome. o No integrity: alongside cleartext traffic, an attacker can make arbitrary modifications to captured traffic and replay it to cause the desired outcome if the recipient has no means to detect these modifications. • T.UNAUTHORIZED_CONNECTION While a VPN client may have the necessary credentials (e.g., certificate, pre-shared key) to connect to a VPN gateway, there may be instances where the remote client, or the machine the client is operating on, has been compromised and attempts to make unauthorized connections. • T.UNPROTECTED_TRAFFIC A remote machine’s network traffic may be exposed to a hostile network. A user may be required to use a hostile (or unknown) network to send network traffic without being able to route the traffic appropriately. 43. No threats are identified for this TOE in addition to those specified in the collaborative Protection Profiles and Extended Packages. 3.2 Assumptions 44. The assumptions made for this TOE are as defined in [NDcPP] Section 4.2 and [FWcPP] Section 3.2 (with appropriate editorial and terminology differences to reflect general network device vs. firewall), namely: • A.PHYSICAL_PROTECTION Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 21 of 89 The network device is assumed to be physically protected in its operational environment and not subject to physical attacks that compromise the security and/or interfere with the device’s physical interconnections and correct operation. This protection is assumed to be sufficient to protect the device and the data it contains. As a result, the cPP will not include any requirements on physical tamper protection or other physical attack mitigations. The cPP will not expect the product to defend against physical access to the device that allows unauthorized entities to extract data, bypass other controls, or otherwise manipulate the device. • A.LIMITED_FUNCTIONALITY The device is assumed to provide networking functionality as its core function and not provide functionality/services that could be deemed as general-purpose computing. For example, the device should not provide a computing platform for general purpose applications (unrelated to networking functionality). • A.TRUSTED_ADMINSTRATOR The Security Administrator(s) for the network device are assumed to be trusted and to act in the best interest of security for the organization. This includes being appropriately trained, following policy, and adhering to guidance documentation. Administrators are trusted to ensure passwords/credentials have sufficient strength and entropy and to lack malicious intent when administering the device. The network device is not expected to be capable of defending against a malicious Administrator that actively works to bypass or compromise the security of the device. For TOEs supporting X.509v3 certificate-based authentication, the Security Administrator(s) are expected to fully validate (e.g. offline verification) any CA certificate (root CA certificate or intermediate CA certificate) loaded into the TOE’s trust store (aka 'root store', ' trusted CA Key Store', or similar) as a trust anchor prior to use (e.g. offline verification). • A.REGULAR_UPDATES The network device firmware and software is assumed to be updated by an Administrator on a regular basis in response to the release of product updates due to known vulnerabilities. • A.ADMIN_CREDENTIALS_SECURE The Administrator’s credentials (private key) used to access the network device are protected by the platform on which they reside. 45. The assumptions A.RESIDUAL_INFORMATION and A.NO_THRU_TRAFFIC_PROTECTION defined in [NDcPP] are not relevant to this TOE as they are addressed by additional requirements introduced through conformance to [FWcPP]. 46. The following assumption A.CONNECTIONS is introduced through compliance to [VPN_EP] and [IPS_EP]. It is typically understood that an ST claiming exact compliance to a Protection Profile cannot introduce assumptions. However, that is on the understanding this limits applicability of the security functional requirements for the TOE, whereas this assumption is a clarification of how the manner in which the TOE is to be connected to distinct networks. • A.CONNECTIONS It is assumed that the TOE is connected to distinct networks in a manner that ensures that the TOE security policies will be enforced on all applicable network traffic flowing among the attached networks. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 22 of 89 47. No assumptions are identified for this TOE in addition to those specified in the collaborative Protection Profiles and Extended Packages. 3.3 Organizational Security Policies 48. The OSP applied for this TOE is as defined in [NDcPP] Section 4.3 and [FWcPP] Section 3.3. The OSP P.ANALYZE applied for this TOE is as defined in [NDcPP] Section A.1.3. No additional OSPs are identified and no modification to the statement of OSPs is made for this TOE. • P.ACCESS_BANNER The TOE shall display an initial banner describing restrictions of use, legal agreements, or any other appropriate information to which users consent by accessing the TOE. • P.ANALYZE Analytical processes and information to derive conclusions about potential intrusions must be applied to IPS data and appropriate response actions taken. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 23 of 89 4 Security Objectives 49. As this TOE is not distributed, none of the objectives relating to distributed TOEs are specified for this TOE. 4.1 Security Objectives for the TOE 50. The security objectives for the TOE are trivially determined through the inverse of the statement of threats presented in [NDcPP] Section 4.1 and [FWcPP] Section 3.1. 51. These are augmented by the statement of security objectives for the TOE in relation to the IPS capabilities as detailed in [IPS_EP] Section 3, namely: • O.SYSTEM_MONITORING The IPS must collect and store information about all events that may indicate an IPS policy violation related to misuse, inappropriate access, or malicious activity on monitored networks. • O.IPS_ANALYZE The IPS must apply analytical processes to network traffic data collected from monitored networks and derive conclusions about potential intrusions or network traffic policy violations. • O.IPS_REACT The IPS must respond appropriately to its analytical conclusions about IPS policy violations. O.TOE_ADMINISTRATION – as also defined by the inverse of the threats defined in [NDcPP] Section 4.1 and [FWcPP] Section 3.1 The IPS will provide a method for authorized administrator to configure the TSF. • O.TRUSTED_COMMUNICATIONS– as also defined by the inverse of the threats defined in [NDcPP] Section 4.1 and [FWcPP] Section 3.1 The IPS will ensure that communications between distributed components of the TOE are not subject to unauthorized modification or disclosure. 52. These are further augmented by the statement of security objectives for the TOE in relation to the IPS capabilities as detailed in [VPN_EP] Section 4.1, namely: • O.ADDRESS_FILTERING To address the issues associated with unauthorized disclosure of information, inappropriate access to services, misuse of services, disruption or denial of services, and network-based reconnaissance, compliant TOE’s will implement Packet Filtering capability. That capability will restrict the flow of network traffic between protected networks and other attached networks based on network addresses of the network nodes originating (source) and/or receiving (destination) applicable network traffic as well as on established connection information. • O.ASSIGNED_PRIVATE_ADDRESS There are instances where a remote client desires secure communication with a gateway that is trusted. While a user may be connected via an untrusted network, it should still be possible to ensure that it can communicate with a known entity that controls the routing of the client’s network packets. This can be accomplished by the VPN headend assigning an IP address that the gateway controls, as well as providing a routing point for the client’s network traffic. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 24 of 89 • O.AUTHENTICATION – as also defined by the inverse of the threats defined in [NDcPP] Section 4.1 and [FWcPP] Section 3.1 To further address the issues associated with unauthorized disclosure of information, a compliant TOE’s authentication ability (IPSec) will allow a VPN peer to establish VPN connectivity with another VPN peer. VPN endpoints authenticate each other to ensure they are communicating with an authorized external IT entity. • O.CLIENT_ESTABLISHMENT_CONSTRAINTS To address the concern that a remote client may be compromised and attempt to establish connections with the headend VPN gateway outside of “normal” operations, this objective specifies conditions under which a remote client may establish connections. The administrator may configure the headend VPN gateway to accept a client’s request for a connection based on attributes the administrator feels are appropriate. • O.CRYPTOGRAPHIC_FUNCTIONS – as also defined by the inverse of the threats defined in [NDcPP] Section 4.1 and [FWcPP] Section 3.1 To address the issues associated with unauthorized disclosure of information, inappropriate access to services, misuse of services, disruption of services, and network- based reconnaissance, compliant TOEs will implement cryptographic capabilities. These capabilities are intended to maintain confidentiality and allow for detection and modification of data that is transmitted outside of the TOE. • O.FAIL_SECURE There may be instances where the TOE’s hardware malfunctions or the integrity of the TOE’s software is compromised, the latter being due to malicious or non-malicious intent. To address the concern of the TOE operating outside of its hardware or software specification, the TOE will shut down upon discovery of a problem reported via the self- test mechanism and provide signature-based validation of updates to the TSF. • O.PORT_FILTERING To further address the issues associated with unauthorized disclosure of information, etc., a compliant TOE’s port filtering capability will restrict the flow of network traffic between protected networks and other attached networks based on the originating (source) and/or receiving (destination) port (or service) identified in the network traffic as well as on established connection information. • O.REMOTE_SESSION_TERMINATION A remote client’s session can become vulnerable when there is a lack of activity. This is primarily due to a user walking away from a device that has a remote connection established. While some devices have a “lock screen” or logout capability, they cannot always assumed to be configured or available. To address this concern, a session termination capability is necessary during an administrator specified time period. • O.SYSTEM_MONITORING – as also defined by the inverse of the threats defined in [NDcPP] Section 4.1 and [FWcPP] Section 3.1 To address the issues of administrators being able to monitor the operations of the VPN gateway, it is necessary to provide a capability to monitor system activity. Compliant TOEs will implement the ability to log the flow of network traffic. Specifically, the TOE will provide the means for administrators to configure packet filtering rules to ‘log’ when network traffic is found to match the configured rule. As a result, matching a rule Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 25 of 89 configured to ‘log’ will result in informative event logs whenever a match occurs. In addition, the establishment of security associations (SAs) is auditable, not only between peer VPN gateways, but also with certification authorities (CAs). • O.TOE_ADMINISTRATION – as also defined by the inverse of the threats defined in [NDcPP] Section 4.1 and [FWcPP] Section 3.1 Compliant TOEs will provide the functions necessary for an administrator to configure the packet filtering rules, as well as the cryptographic aspects of the IPsec protocol that are enforced by the TOE. 4.2 Security Objectives for the Operational Environment 53. The statement of security objectives for the operational environment of this TOE is as defined in [NDcPP] Section 5.1, [FWcPP] Section 4.1 (with appropriate editorial and terminology differences to reflect general network device vs. firewall), and [IPS_EP] Section A.2.2 namely: • OE.PHYSICAL Physical security, commensurate with the value of the TOE and the data it contains, is provided by the environment. • OE.NO_GENERAL_PURPOSE There are no general-purpose computing capabilities (e.g., compilers or user applications) available on the TOE, other than those services necessary for the operation, administration and support of the TOE. • OE.TRUSTED_ADMIN Security Administrators are trusted to follow and apply all guidance documentation in a trusted manner. For TOEs supporting X.509v3 certificate-based authentication, the Security Administrator(s) are assumed to monitor the revocation status of all certificates in the TOE's trust store and to remove any certificate from the TOE’s trust store in case such certificate can no longer be trusted.3 • OE.UPDATES The TOE firmware and software is updated by an Administrator on a regular basis in response to the release of product updates due to known vulnerabilities. • OE.ADMIN_CREDENTIALS_SECURE The Administrator’s credentials (private key) used to access the TOE must be protected on any other platform on which they reside. • OE.CONNECTIONS TOE administrators will ensure that the TOE is installed in a manner that will allow the TOE to effectively enforce its policies on network traffic of monitored networks. 54. The security objectives for the operational environment OE.NO_THRU_TRAFFIC_PROTECTION and OE.RESIDUAL_INFORMATION defined in [NDcPP] are not relevant to this TOE as they are addressed by objectives for the TOE introduced through conformance to [FWcPP]. No additional security objectives for the operational environment are identified for this ST. 3 As specified in Network Device Interpretation #201712rev 2, dated 29 Jan 2018, “NITDecisionRfI201712rev2” Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 26 of 89 4.3 Security Objectives rationale 55. As these objectives for the TOE and operational environment are the same as those specified in [NDcPP], [FWcPP], [VPN_EP]and [IPS_EP],the rationales provided in the prose of the following are wholly applicable to this security target as the statements of threats, assumptions, OSPs and security objectives provided in this security target are the same as those defined in the collaborative Protection Profiles and Extended Packages to which this ST claims conformance • [NDcPP] section 4 • [FWcPP], section 3 • [IPS_EP] section 3 & Annex A.2 • [VPN_EP]and section 5 and Annex A. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 27 of 89 5 Security Functional Requirements 56. All security functional requirements are taken from the [NDcPP] and [FWcPP] collaborative Protection Profiles and from the [IPS_EP] and [VPN_EP] Extended Packages. The Security Functional requirements are primarily structured according to [NDcPP], with requirements and operations from [FWcPP], [IPS_EP] and [VPN_EP] inserted as appropriate. The SFRs are presented in accordance with the conventions described in [NDcPP] Section 6.1, and section 1.4 of this document. 57. Note: as this TOE is not distributed, none of the security functional requirements relating to distributed TOEs are specified for this TOE. 5.1 Security Audit (FAU) 5.1.1 Security Audit Data generation (FAU_GEN) 5.1.1.1 FAU_GEN.1 Audit data generation FAU_GEN.1/ND Network Device Audit Data Generation FAU_GEN.1.1/ND The TSF shall be able to generate an audit record of the following auditable events: a) Start-up and shut-down of the audit functions; b) All auditable events for the not specified level of audit; and c) All administrative actions comprising: • Administrative login and logout (name of user account shall be logged if individual user accounts are required for Administrators). • Changes to TSF data related to configuration changes (in addition to the information that a change occurred it shall be logged what has been changed). • Generating/import of, changing, or deleting of cryptographic keys (in addition to the action itself a unique key name or key reference shall be logged). • Resetting passwords (name of related user account shall be logged). • [Starting and stopping services]; d) Specifically defined auditable events listed in Table 4. ST Application Note: The “Services” referenced in the above requirement relate to the trusted communication channel to the external syslog server (netconf over SSH) and the trusted path for remote administrative sessions (SSH, which can be tunneled over IPsec). FAU_GEN.1.2/ND The TSF shall record within each audit record at least the following information: a) Date and time of the event, type of event, subject identity, and the outcome (success or failure) of the event; and b) For each audit event type, based on the auditable event definitions of the functional components included in the ST, information specified in column three of Table 4. Requirement Auditable Events Additional Audit Record Contents FAU_GEN.1 None None FAU_GEN.2 None None FAU_STG_EXT.1 None None FAU_STG.1 None None Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 28 of 89 FCS_CKM.1 None None FCS_CKM.2 None None FCS_CKM.4 None None FCS_COP.1/DataEncryption None None FCS_COP.1/SigGen None None FCS_COP.1/Hash None None FCS_COP.1/KeyedHash None None FCS_RBG_EXT.1 None None FDP_RIP.2 None None FIA_AFL.1 Unsuccessful login attempts limit is met or exceeded. Origin of the attempt (e.g., IP address). FIA_PMG_EXT.1 None None FIA_UIA_EXT.1 All use of identification and authentication mechanism. Provided user identity, origin of the attempt (e.g., IP address). FIA_UAU_EXT.2 All use of identification and authentication mechanism. Origin of the attempt (e.g., IP address). FIA_UAU.7 None None FMT_MOF.1/ManualUpdate Any attempt to initiate a manual update None FMT_MTD.1/CoreData All management activities of TSF data None FMT_SMF.1 None None FMT_SMR.2 None None FPT_SKP_EXT.1 None None FPT_APW_EXT.1 None None FPT_TST_EXT.1 None None FPT_TUD_EXT.1 Initiation of update; result of the update attempt (success or failure) None. FPT_STM_EXT.1 Discontinuous changes to time - either Administrator actuated or changed via an automated process. For discontinuous changes to time: The old and new values for the time. Origin of the attempt to change time for success and failure (e.g., IP address). FTA_SSL_EXT.1 The termination of a local interactive session by the session locking mechanism. None. FTA_SSL.3 The termination of a remote session by the session locking mechanism. None FTA_SSL.4 The termination of an interactive session. None FTA_TAB.1 None None FTP_ITC.1 Initiation of the trusted channel. Termination of the trusted channel. Failure of the trusted channel functions. Identification of the initiator and target of failed trusted channels establishment attempt. FTP_TRP.1/Admin Initiation of the trusted path. None. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 29 of 89 Termination of the trusted path. Failure of the trusted path functions. FCS_SSHS_EXT.1 Failure to establish an SSH session Reason for failure FIA_X509_EXT.1/Rev Unsuccessful attempt to validate a certificate Reason for failure FIA_X509_EXT.2 None None FIA_X509_EXT.3 None None FMT_MOF.1/Functions Modification of the behaviour of the transmission of audit data to an external IT entity, the handling of audit data, the audit functionality when Local Audit Storage Space is full. None. FMT_MOF.1/Services Starting and stopping of services. None FMT_MTD.1/CryptoKeys Management of cryptographic keys. None. FFW_RUL_EXT.1 Application of rules configured with the ‘log’ operation Source and destination addresses Source and destination ports Transport Layer Protocol TOE Interface Indication of packets dropped due to too much network traffic TOE interface that is unable to process packets Identifier of rule causing packet drop FFW_RUL_EXT.2 None None FCS_IPSEC_EXT.1 Session Establishment with peer Entire packet contents of packets transmitted/received during session establishment FIA_X509_EXT.1 Session establishment with CA Entire packet contents of packets transmitted/received during session establishment FPF_RUL_EXT.1 Application of rules configured with the ‘log’ operation Source and destination addresses Source and destination ports Transport Layer Protocol TOE Interface Indication of packets dropped due to too much network traffic TOE interface that is unable to process packets Table 4 FAU_GEN.1 Security Functional Requirements and Auditable Events Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 30 of 89 FAU_GEN.1/IPS IPS Audit Data Generation4 FAU_GEN.1.1/IPS The TSF shall be able to generate an IPS audit record of the following IPS auditable events: a) Start-up and shut-down of the IPS functions; b) All IPS auditable events for the [not specified] level of audit; and c) All administrative actions; d) [All dissimilar IPS events; e) All dissimilar IPS reactions; f) Totals of similar events occurring within a specified time period; and g) Totals of similar reactions occurring within a specified time period.] FAU_GEN.1.2/IPS The TSF shall record within each IPS auditable event record at least the following information: a) Date and time of the event, type of event and/or reaction; subject identity, and the outcome (success or failure) of the event; and b) For each IPS auditable event type, based on the auditable event definitions of the functional components included in the PP/ST, [Specifically defined auditable events listed in Table 5]. Requirement IPS Auditable Events Additional Details FMT_SMF.1/IPS Modification of an IPS policy element. Identifier or name of the modified IPS policy element (e.g. which signature, baseline, or known-good/known-bad list was modified. IPS_ABD_EXT.1 Inspected traffic matches an anomaly-based IPS policy. Source and destination IP addresses. The content of the header fields that were determined to match the policy. TOE interface that received the packet. Aspect of the anomaly-based IPS policy rule that triggered the event (e.g. throughput, time of day, frequency, etc.). Network-based action by the TOE (e.g. allowed, blocked, sent reset to source IP, sent blocking notification to firewall). IPS_IPB_EXT.1 Inspected traffic matches a list of known-good or known-bad addresses applied to an IPS policy. Source and destination IP addresses (and, if applicable, indication of whether the source and/or destination address matched the list). TOE interface that received the packet. Network-based action by the TOE (e.g. allowed, blocked, sent reset) 4 Specified in [IPS_EP]. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 31 of 89 IPS_NTA_EXT.1 Modification of which IPS policies are active on a TOE interface. Enabling/disabling a TOE interface with IPS policies applied. Modification of which mode(s) is/are active on a TOE interface. Identification of the TOE interface The IPS policy and interface mode (if applicable). IPS_SBD_EXT.1 Inspected traffic matches a signature-based IPS with logging enabled. Name or identifier of the matched signature. Source and destination IP addresses. The content of the header fields that were determined to match the signature. TOE interface that received the packet. Network-based action by the TOE (e.g. allowed, blocked, sent reset) Table 5 Audit Events and Details from IPSEP 5.1.1.2 FAU_GEN.2 User identity association FAU_GEN.2 User identity association5 FAU_GEN.2.1 For audit events resulting from actions of identified users, the TSF shall be able to associate each auditable event with the identity of the user that caused the event. 5.1.2 Security audit event storage (Extended – FAU_STG_EXT) 5.1.2.1 FAU_ STG_EXT.1 Protected Audit Event Storage FAU_STG_EXT.1 Protected Audit Event Storage6 FAU_STG_EXT.1.1 The TSF shall be able to transmit the generated audit data to an external IT entity using a trusted channel according to FTP_ITC.1. ST Application Note Transfer of the audit date to the external server is performed automatically (without further Security Administrator intervention) in the evaluated deployment. FAU_STG_EXT.1.2 TOE shall consist of a single standalone component that stores audit data locally. FAU_STG_EXT.1.3 The TSF shall [overwrite previous audit records according to the following rule: [oldest log is overwritten]] when the local storage space for audit data is full. 5 Specified in [NDcPP], [FWcPP], [IPS_EP]. 6 Specified in [NDcPP], [FWcPP]. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 32 of 89 5.1.2.2 FAU_STG.1 Protected audit trail storage (Optional) FAU_STG.1 Protected audit trail storage7 FAU_STG.1.1 The TSF shall protect the stored audit records in the audit trail from unauthorised deletion. FAU_STG.1.2 The TSF shall be able to prevent unauthorised modifications to the stored audit records in the audit trail. 5.2 Cryptographic Support (FCS) 5.2.1 Cryptographic Key Management (FCS_CKM) 5.2.1.1 FCS_CKM.1 Cryptographic Key Generation (Refinement) FCS_CKM.1/ND Cryptographic Key Generation/ND8 FCS_CKM.1.1/ND The TSF shall generate asymmetric cryptographic keys in accordance with a specified cryptographic key generation algorithm: [ • RSA schemes using cryptographic key sizes of 2048-bit or greater that meet the following: FIPS PUB 186-4, “Digital Signature Standard (DSS)”, Appendix B.3; • ECC schemes using “NIST curves” [P-256, P-384, P-521] that meet the following: FIPS PUB 186-4, “Digital Signature Standard (DSS)”, Appendix B.4; • FFC Schemes using Diffie-Hellman group 14 that meet the following: RFC 3526, Section 39 ] and specified cryptographic key sizes [assignment: cryptographic key sizes] that meet the following: [assignment: list of standards]. 5.2.1.2 FCS_CKM.1 Cryptographic Key Generation (Refinement) FCS_CKM.1/IKE Cryptographic Key Generation (for IKE Peer Authentication)10 FCS_CKM.1.1/IKE The TSF shall generate asymmetric cryptographic keys used for IKE peer authentication in accordance with a [ • FIPS PUB 186-4, “Digital Signature Standard (DSS)”, Appendix B.3 for RSA schemes; • FIPS PUB 186-4, “Digital Signature Standard (DSS)”, Appendix B.4 for ECDSA schemes and implementing “NIST curves” P-256, P-384 and [no other curves]] and specified cryptographic key sizes equivalent to, or greater than, a symmetric key strength of 112 bits. 5.2.1.3 FCS_CKM.2 Cryptographic Key Establishment (Refinement) FCS_CKM.2 Cryptographic Key Establishment FCS_CKM.2.1 The TSF shall perform cryptographic key establishment in accordance with a specified cryptographic key establishment method: [ • Elliptic curve-based key establishment schemes that meet the following: NIST Special Publication 800-56A Revision 2, “Recommendation for Pair-Wise Key Establishment Schemes Using Discrete Logarithm Cryptography”; 7 Specified in [NDcPP] and [FWcPP]. 8 Specified in [NDcPP], [FWcPP]. 9 As per TD0291 and Network Device Interpretations #201723rev2, in NITDecisionRfi201723rev2.pdf 10 Specified in [VPN_EP]. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 33 of 89 • Key establishment scheme using Diffie-Hellman group 14 that meets the following: RFC 3526, Section 3; ] that meets the following: [assignment: list of standards]. 5.2.1.4 FCS_CKM.4 Cryptographic Key Destruction FCS_CKM.4 Cryptographic Key Destruction FCS_CKM.4.1 The TSF shall destroy cryptographic keys in accordance with a specified cryptographic key destruction method • For plaintext keys in volatile storage, the destruction shall be executed by a [destruction of reference to the key directly followed by a request for garbage collection]; • For plaintext keys in non-volatile storage, the destruction shall be executed by the invocation of an interface provided by a part of the TSF that [ o logically addresses the storage location of the key and performs a [single overwrite consisting of [zeroes]] that meets the following: No Standard. 5.2.2 Cryptographic Operation (FCS_COP) 5.2.2.1 FCS_COP.1 Cryptographic Operation FCS_COP.1/DataEncryption Cryptographic Operation (AES Data Encryption/Decryption) FCS_COP.1.1/DataEncryption The TSF shall perform encryption/decryption in accordance with a specified cryptographic algorithm AES used in [GCM, CBC, CTR] mode and cryptographic key sizes [128 bits, 192 bits, 256 bits] that meet the following AES as specified in ISO 18033-3, [CBC as specified in ISO 10116, CTR as specified in ISO 10116, GCM as specified in ISO 19772]. FCS_COP.1/SigGen Cryptographic Operation (Signature Generation and Verification) FCS_COP.1.1/SigGen The TSF shall perform cryptographic signature services (generation and verification) in accordance with a specified cryptographic algorithm [ • RSA Digital Signature Algorithm and cryptographic key sizes (modulus) [2048 bits, 4096 bits], • Elliptic Curve Digital Signature Algorithm and cryptographic key sizes [256 bits, 384 bits, 521 bits] ] and cryptographic key sizes [assignment: cryptographic key sizes] that meet the following: [ • For RSA schemes: FIPS PUB 186-4, “Digital Signature Standard (DSS)”, Section 5.5, using PKCS #1 v2.1 Signature Schemes RSASSA-PSS and/or RSASSA-PKCS1v1_5; ISO/IEC 9796-2, Digital signature scheme 2 or Digital Signature scheme 3, • For ECDSA schemes: FIPS PUB 186-4, “Digital Signature Standard (DSS)”, Section 6 and Appendix D, Implementing “NIST curves” [P-256, P-384, P-521]; ISO/IEC 14888-3, Section 6.4 ]. FCS_COP.1/Hash Cryptographic Operation (Hash Algorithm) FCS_COP.1.1/Hash The TSF shall perform cryptographic hashing services in accordance with a specified cryptographic algorithm [SHA-1, SHA-256, SHA-384, SHA-512] and cryptographic key sizes Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 34 of 89 [assignment: cryptographic key sizes] and message digest sizes [160, 256, 384, 512] bits that meet the following: ISO/IEC 10118-3:2004. FCS_COP.1/KeyedHash Cryptographic Operation (Keyed Hash Algorithm) FCS_COP.1.1/KeyedHash The TSF shall perform keyed-hash message authentication in accordance with a specified cryptographic algorithm [HMAC-SHA-1, HMAC-SHA-256, HMAC-SHA-512] and cryptographic key sizes [160, 256 and 512 bits] and message digest sizes [160, 256 and 512] bits that meet the following: ISO/IEC 9797-2:2011, Section 7 “MAC Algorithm 2”. 5.2.3 Random Bit Generation (Extended – FCS_RBG_EXT) 5.2.3.1 FCS_RBG_EXT.1 Random Bit Generation FCS_RBG_EXT.1 Random Bit Generation FCS_RBG_EXT.1.1 The TSF shall perform all deterministic random bit generation services in accordance with ISO/IEC 18031:2011 using [HMAC_DRBG (any)]. FCS_RBG_EXT.1.2 The deterministic RBG shall be seeded by at least one entropy source that accumulates entropy from [[1] software-based noise source, [1] hardware-based noise source] with a minimum of [256 bits] of entropy at least equal to the greatest security strength, according to ISO/IEC 18031:2011 Table C.1 “Security Strength Table for Hash Functions”, of the keys and hashes that it will generate. 5.2.4 Cryptographic Protocols (Extended – FCS_ IPSEC_EXT & FCS_SSHS_EXT SSH Protocol 5.2.4.1 FCS_IPSEC_EXT.1 IPsec Protocol FCS_IPSEC_EXT.1 IPsec Protocol FCS_IPSEC_EXT.1.1 The TSF shall implement the IPsec architecture as specified in RFC 4301. FCS_IPSEC_EXT.1.2 The TSF shall have a nominal, final entry in the SPD that matches anything that is otherwise unmatched, and discards it. FCS_IPSEC_EXT.1.3 The TSF shall implement [tunnel mode]. FCS_IPSEC_EXT.1.4 The TSF shall implement the IPsec protocol ESP as defined by RFC 4303 using the cryptographic algorithms [AES-CBC-128, AES-CBC-256 (specified in RFC 3602), , AES-GCM-128, AES- GCM-256 (specified in RFC 4106)] and [AES-CBC-192 (specified in RFC 3602), AES-GCM-192 (specified in RFC 4106)] together with a Secure Hash Algorithm (SHA)-based HMAC [HMAC-SHA-256]11 . FCS_IPSEC_EXT.1.5 The TSF shall implement the protocol [IKEv1, using Main Mode for Phase 1 exchanges, as defined in RFCs 2407, 2408, 2409, RFC 4109, [no other RFCs for extended sequence numbers], and [RFC 4868 for hash functions]; • IKEv2 as defined in RFC 5996 and [with no support for NAT traversal], and [RFC 4868 for hash functions] ] FCS_IPSEC_EXT.1.6 The TSF shall ensure the encrypted payload in the [IKEv1, IKEv2] protocol uses the cryptographic algorithms [AES-CBC-128, AES-CBC-192, AES-CBC-256 (specified in RFC 3602), AES- GCM-128, AES-GCM-256 (specified in RFC 5282)]. 11 The SFR is specified as per TD 0436. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 35 of 89 FCS_IPSEC_EXT.1.7 The TSF shall ensure that [ • IKEv1 Phase 1 SA lifetimes can be configured by a Security Administrator based on [ o length of time, where the time values can be configured within [0.2-24] hours12 ; ]; • IKEv2 SA lifetimes can be configured by a Security Administrator based on [ o length of time, where the time values can be configured within [0.2-24] hours ] ]. FCS_IPSEC_EXT.1.8 The TSF shall ensure that [ • IKEv1 Phase 2 SA lifetimes can be configured by a Security Administrator based on [ o number of bytes; o length of time, where the time values can be configured within [8] hours; ]; • IKEv2 Child SA lifetimes can be configured by a Security Administrator based on [ o number of bytes; o length of time, where the time values can be configured within [8] hours; ] ]. FCS_IPSEC_EXT.1.9 The TSF shall generate the secret value x used in the IKE Diffie-Hellman key exchange (“x” in g^x mod p) using the random bit generator specified in FCS_RBG_EXT.1, and having a length of at least [112 (for DH Group 14), 128 (for DH Groups 19 and 24) and 192 (for DH Group 20)] bits. FCS_IPSEC_EXT.1.10 The TSF shall generate nonces used in [IKEv1, IKEv2] exchanges of length [ • at least 128 bits in size and at least half the output size of the negotiated pseudorandom function (PRF) hash ]. FCS_IPSEC_EXT.1.11 The TSF shall ensure that IKE protocols implement DH Group(s) [14 (2048-bit MODP), 19 (256-bit Random ECP), 20 (384-bit Random ECP), 24 (2048-bit MODP with 256-bit POS)]13 . FCS_IPSEC_EXT.1.12 The TSF shall be able to ensure by default that the strength of the symmetric algorithm (in terms of the number of bits in the key) negotiated to protect the [IKEv1 Phase 1, IKEv2 IKE_SA] connection is greater than or equal to the strength of the symmetric algorithm (in terms of the number of bits in the key) negotiated to protect the [IKEv1 Phase 2, IKEv2 CHILD_SA] connection. FCS_IPSEC_EXT.1.13 The TSF shall ensure that all IKE protocols perform peer authentication using [RSA, ECDSA] that use X.509v3 certificates that conform to RFC 4945 and [Pre-shared Keys]. FCS_IPSEC_EXT.1.14 The TSF shall only establish a trusted channel if the presented identifier in the received certificate matches the configured reference identifier, where the presented and reference identifiers are Distinguished Name (DN) [IP address, Fully Qualified Domain Name (FQDN), user FQDN] 14 . 12 Length of time can be configured between 180 seconds and 86,400 seconds. 13 The SFR is specified as per [NDcPP] rather than the alternative presentation of the same requirements in [VPN_EP]. It also incorporates NIAP TD0209. 14 The SFR is specified per [VPN_EP] as modified by TD0329 and TD0343. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 36 of 89 5.2.4.2 FCS_SSHS_EXT.1 SSH Server Protocol FCS_SSHS_EXT.1 SSH Server Protocol FCS_SSHS_EXT.1.1 The TSF shall implement the SSH protocol that complies with RFC(s) [4251, 4252, 4253, 4254, 5656, 6668]15 . FCS_SSHS_EXT.1.2 The TSF shall ensure that the SSH protocol implementation supports the following authentication methods as described in RFC 4252: public key-based, [password-based]16 . FCS_SSHS_EXT.1.3 The TSF shall ensure that, as described in RFC 4253, packets greater than [256K] bytes in an SSH transport connection are dropped. FCS_SSHS_EXT.1.4 The TSF shall ensure that the SSH transport implementation uses the following encryption algorithms and rejects all other encryption algorithms: [aes128-cbc, aes256-cbc, aes128- ctr, aes256-ctr]17 . FCS_SSHS_EXT.1.5 The TSF shall ensure that the SSH public-key based authentication implementation uses [ssh-rsa, ecdsa-sha2-nistp256, ecdsa-sha2-nistp384, ecdsa-sha2-nistp521] as its public key algorithm(s) and rejects all other public key algorithms18 . FCS_SSHS_EXT.1.6 The TSF shall ensure that the SSH transport implementation uses [hmac- sha1,hmac-sha2-256, hmac-sha2-512] as its MAC algorithm(s) and rejects all other MAC algorithm(s). FCS_SSHS_EXT.1.7 The TSF shall ensure that [diffie-hellman-group14-sha1, ecdh-sha2-nistp256] and [ecdh-sha2-nistp384, ecdh-sha2-nistp521] are the only allowed key exchange methods used for the SSH protocol. FCS_SSHS_EXT.1.8 The TSF shall ensure that within SSH connections the same session keys are used for a threshold of no longer than one hour, and no more than one gigabyte of transmitted data. After either of the thresholds are reached a rekey needs to be performed. 5.3 Identification and Authentication (FIA) 5.3.1 Authentication Failure Management (FIA_AFL) 5.3.1.1 FIA_AFL.1 Authentication Failure Management (Refinement) FIA_AFL.1 Authentication Failure Management19 FIA_AFL.1.1 The TSF shall detect when an Administrator configurable positive integer within [1 to 10] unsuccessful authentication attempts occur related to Administrators attempting to authenticate remotely using a password. FIA_AFL.1.2 When the defined number of unsuccessful authentication attempts has been met, the TSF shall [prevent the offending Administrator from successfully establishing remote session using any authentication method that involves a password until [Security Administrator has unlocked the account] is taken by an Administrator; prevent the offending Administrator from successfully establishing remote session using any authentication method that involves a password until an Administrator defined time period has elapsed]. 15 Incorporates TD0398 16 Incorporates TD0339 17 Incorporates NIAP TD0337 18 In accordance with TD0424 19 Specified in [NDcPP] and [VPN_EP], stated using the wording of [NDcPP], incorporates TD0408. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 37 of 89 ST Application Note The Security Administrator can select to unlock the account of another administrator who has failed to authenticate through the local console, rather than require the administrator to wait until the delay of an administrator-configured time period has lapsed before another attempt can be made to authenticate. 5.3.2 Password Management (Extended – FIA_PMG_EXT) 5.3.2.1 FIA_PMG_EXT.1 Password Management FIA_PMG_EXT.1 Password Management20 FIA_PMG_EXT.1.1 The TSF shall provide the following password management capabilities for administrative passwords: a) Passwords shall be able to be composed of any combination of upper and lower case letters, numbers, and the following special characters: [“!”, “@”, “#”, “$”, “%”, “^”, “&”, “*”, “(“, “)”, [and all other standard ASCII, extended ASCII and Unicode characters]]; b) Minimum password length shall be configurable to between [10] and [20] characters. 5.3.3 User Identification and Authentication (Extended – FIA_UIA_EXT) 5.3.3.1 FIA_UIA_EXT.1 User Identification and Authentication FIA_UIA_EXT.1 User Identification and Authentication21 FIA_UIA_EXT.1.1 The TSF shall allow the following actions prior to requiring the non-TOE entity to initiate the identification and authentication process: • Display the warning banner in accordance with FTA_TAB.1; • [[ICMP echo]]. FIA_UIA_EXT.1.2 The TSF shall require each administrative user to be successfully identified and authenticated before allowing any other TSF-mediated actions on behalf of that administrative user. 5.3.4 User authentication (FIA_UAU) (Extended – FIA_UAU_EXT) 5.3.4.1 FIA_UAU_EXT.2 Password-based Authentication Mechanism FIA_UAU_EXT.2 Password-based Authentication Mechanism22 FIA_UAU_EXT.2.1 The TSF shall provide a local password-based authentication mechanism to perform local administrative user authentication. 5.3.4.2 FIA_UAU.7 Protected Authentication Feedback FIA_UAU.7 Protected Authentication Feedback23 FIA_UAU.7.1 The TSF shall provide only obscured feedback to the administrative user while the authentication is in progress at the local console. 20 Specified in [NDcPP] and [FWcPP]. 21 Specified in [NDcPP] and [FWcPP]. 22 Specified in [NDcPP] and [FWcPP] and TD408. 23 Specified in [NDcPP] and [FWcPP]. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 38 of 89 5.3.5 Authentication using X.509 certificates (Extended – FIA_X509_EXT) 5.3.5.1 FIA_X509_EXT.1 X.509 Certificate Validation FIA_X509_EXT.1/Rev X.509 Certificate Validation FIA_X509_EXT.1.1/Rev The TSF shall validate certificates in accordance with the following rules: • RFC 5280 certificate validation and certificate path validation supporting a minimum path length of three certificates. • The certificate path must terminate with a trusted CA certificate. • The TSF shall validate a certification path by ensuring that all CA certificates in the certification path contain the basicConstraints extension with the CA flag set to TRUE24 . • The TSF shall validate the revocation status of the certificate using [a Certificate Revocation List (CRL) as specified in RFC 5280 Section 6.3] • The TSF shall validate the extendedKeyUsage field according to the following rules: o Certificates used for trusted updates and executable code integrity verification shall have the Code Signing purpose (id-kp 3 with OID 1.3.6.1.5.5.7.3.3) in the extendedKeyUsage field. o Server certificates presented for TLS shall have the Server Authentication purpose (id-kp 1 with OID 1.3.6.1.5.5.7.3.1) in the extendedKeyUsage field. o Client certificates presented for TLS shall have the Client Authentication purpose (id-kp 2 with OID 1.3.6.1.5.5.7.3.2) in the extendedKeyUsage field. o OCSP certificates presented for OCSP responses shall have the OCSP Signing purpose (id-kp 9 with OID 1.3.6.1.5.5.7.3.9) in the extendedKeyUsage field. FIA_X509_EXT.1.2/Rev The TSF shall only treat a certificate as a CA certificate if the basicConstraints extension is present and the CA flag is set to TRUE. 5.3.5.2 FIA_X509_EXT.2 X.509 Certificate Authentication FIA_X509_EXT.2 X.509 Certificate Authentication FIA_X509_EXT.2.1 The TSF shall use X.509v3 certificates as defined by RFC 5280 to support authentication for [IPsec], and [no additional uses]. FIA_X509_EXT.2.2 When the TSF cannot establish a connection to determine the validity of a certificate, the TSF shall [allow the Administrator to choose whether to accept the certificate in these cases, not accept the certificate]. 5.3.5.3 FIA_X509_EXT.3 X.509 Certificate Requests FIA_X509_EXT.3 X.509 Certificate Requests FIA_X509_EXT.3.1 The TSF shall generate a Certificate Request Message as specified by RFC 2986 and be able to provide the following information in the request: public key and [device-specific information, Common Name, Organization, Organizational Unit, Country]. FIA_X509_EXT.3.2 The TSF shall validate the chain of certificates from the Root CA upon receiving the CA Certificate Response. 24 Incorporates TD0340 Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 39 of 89 5.3.5.4 FIA_PSK_EXT.1 Pre-Shared Keys 5.3.5.5 FIA_PSK_EXT.1 Pre-Shared Keys 25 FIA_PSK_EXT.1.1 The TSF shall be able to use pre-shared keys for IPsec and [no other protocols]. FIA_PSK_EXT.1.2 The TSF shall be able to accept text-based pre-shared keys that: • are 22 characters and [1 to 255 characters]; • composed of any combination of upper and lower case letters, numbers, and special characters (that include: “!”, “@”, “#”, “$”, “%”, “^”, “&”, “*”, “(“, and “)”). FIA_PSK_EXT.1.3 The TSF shall condition the text-based pre-shared keys by using [SHA-1, [conversion of the text string into an authentication value as per RFC 2409 for IKEv1 or RFC 4306 for IKEv2, using the pseudo-random function that is configured as the hash algorithm for the IKE exchanges]]. FIA_PSK_EXT.1.4 The TSF shall be able to [accept] bit-based pre-shared keys. 5.4 Security Management (FMT) 5.4.1 Management of functions in TSF (FMT_MOF) 5.4.1.1 FMT_MOF.1/ManualUpdate Management of security functions behaviour FMT_MOF.1/ManualUpdate Management of security functions behaviour FMT_MOF.1.1/ManualUpdate The TSF shall restrict the ability to enable the functions to perform manual updates to Security Administrators. 5.4.1.2 FMT_MOF.1/Services Management of security functions behaviour FMT_MOF.1/Services Management of security functions behaviour FMT_MOF.1.1/Services The TSF shall restrict the ability to enable and disable the functions and services to Security Administrators. 5.4.1.3 FMT_MOF.1/Functions Management of security functions behaviour FMT_MOF.1/Functions Management of security functions behaviour FMT_MOF.1.1/Functions The TSF shall restrict the ability to [modify the behaviour of] the functions [transmission of audit data to an external IT entity, handling of audit data] to Security Administrators. 5.4.2 Management of TSF Data (FMT_MTD) 5.4.2.1 FMT_MTD.1/CoreData Management of TSF Data FMT_MTD.1/CoreData Management of TSF Data FMT_MTD.1.1/CoreData The TSF shall restrict the ability to manage the TSF data to Security Administrators. 25 Specified in [VPN_EP]. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 40 of 89 5.4.2.2 FMT_MTD.1/CryptoKeys Management of TSF data FMT_MTD.1/CryptoKeys Management of TSF data26 FMT_MTD.1.1/CryptoKeys The TSF shall restrict the ability to manage the cryptographic keys and certificates used for VPN operation to Security Administrators. 5.4.3 Specification of Management Functions (FMT_SMF) 5.4.3.1 FMT_SMF.1 Specification of Management Functions FMT_SMF.1/ND Specification of Management Functions for ND27 FMT_SMF.1.1/ND The TSF shall be capable of performing the following management functions: [ • Ability to administer the TOE locally and remotely; • Ability to configure the access banner; • Ability to configure the session inactivity time before session termination or locking; • Ability to update the TOE, and to verify the updates using digital signature and [no other] capability prior to installing those updates; • Ability to configure the authentication failure parameters for FIA_AFL.1; • Ability to configure firewall rules; • Ability to configure the cryptographic functionality; • Ability to configure the lifetime for IPsec SAs; • Ability to import X.509v3 certificates; • Ability to enable, disable, determine and modify the behavior of all the security functions of the TOE identified in this EP [VPN_EP] to the Administrator; • Ability to configure all security management functions identified in [VPN_EP]other sections of this EP • [ o Ability to configure audit behaviour; o Ability to configure thresholds for SSH rekeying; o Ability to re-enable an Administrator account; o Ability to set the time which is used for time-stamps; o Ability to configure the reference identifier for the peer]. ] FMT_SMF.1/IPS Specification of Management Functions for IPS28 FMT_SMF.1.1/IPS The TSF shall be capable of performing the following management functions: [ • Enable, disable signatures applied to sensor interfaces, and determine the behavior of IPS functionality • Modify these parameters that define the network traffic to be collected and analyzed: o Source IP addresses (host address and network address) o Destination IP addresses (host address and network address) o Source port (TCP and UDP) o Destination port (TCP and UDP) o Protocol (IPv4 and IPv6) o ICMP type and code • Update (import) signatures 26 Specified in [VPN_EP] and TD0317 27 Specified in [VPN_EP] , TD0179 and TD0319. 28 Specified in [IPS_EP]. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 41 of 89 • Create custom signatures • Configure anomaly detection • Enable and disable actions to be taken when signature or anomaly matches are detected • Modify thresholds that trigger IPS reactions • Modify the duration of traffic blocking actions • Modify the known-good and known-bad lists (of IP addresses or address ranges) • Configure the known-good and known-bad lists to override signature-based IPS policies] 5.4.4 Security management roles (FMT_SMR) 5.4.4.1 FMT_SMR.2 Restrictions on security roles FMT_SMR.2 Restrictions on Security Roles FMT_SMR.2.1 The TSF shall maintain the roles: • Security Administrator. FMT_SMR.2.2 The TSF shall be able to associate users with roles. FMT_SMR.2.3 The TSF shall ensure that the conditions • The Security Administrator role shall be able to administer the TOE locally; • The Security Administrator role shall be able to administer the TOE remotely are satisfied. 5.5 Protection of the TSF (FPT) 5.5.1 Protection of TSF Data (Extended – FPT_SKP_EXT) 5.5.1.1 FPT_SKP_EXT.1 Protection of TSF Data (for reading of all pre-shared, symmetric and private keys) FPT_SKP_EXT.1 Protection of TSF Data (for reading of all pre-shared, symmetric and private keys) FPT_SKP_EXT.1.1 The TSF shall prevent reading of all pre-shared keys, symmetric keys, and private keys. 5.5.2 Protection of Administrator Passwords (Extended – FPT_APW_EXT) 5.5.2.1 FPT_APW_EXT.1 Protection of Administrator Passwords FPT_APW_EXT.1 Protection of Administrator Passwords FPT_APW_EXT.1.1 The TSF shall store passwords in non-plaintext form. FPT_APW_EXT.1.2 The TSF shall prevent the reading of plaintext passwords. 5.5.3 TSF testing (Extended – FPT_TST_EXT) 5.5.3.1 FPT_TST_EXT.1 TSF Testing (Extended) FPT_TST_EXT.1 TSF testing FPT_TST_EXT.1.1 The TSF shall run a suite of the following self-tests [during initial start-up (on power on)] to demonstrate the correct operation of the TSF: [ • Power on test, • File integrity test, • Crypto integrity test, Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 42 of 89 • Authentication test, • Algorithm known answer tests]. 5.5.3.2 FPT_TST_EXT.2/VPN TSF Testing FPT_TST_EXT.3 TSF Testing29 FPT_TST_EXT.3.1/VPN The TSF shall provide the capability to verify the integrity of stored TSF executable code when it is loaded for execution through the use of the TSF-provided cryptographic service specified in FCS_COP.1/SigGen. 5.5.4 Trusted Update (FPT_TUD_EXT) 5.5.4.1 FPT_TUD_EXT.1 Trusted Update FPT_TUD_EXT.1 Trusted update FPT_TUD_EXT.1.1 The TSF shall provide Security Administrators the ability to query the currently executing version of the TOE firmware/software and [no other TOE firmware/software version]. FPT_TUD_EXT.1.2 The TSF shall provide Security Administrators the ability to manually initiate updates to TOE firmware/software and [no other update mechanism]. FPT_TUD_EXT.1.3 The TSF shall provide means to authenticate firmware/software updates to the TOE using a digital signature mechanism and [no other mechanisms] prior to installing those updates30 . 5.5.5 Time stamps (Extended – FPT_STM_EXT)) 5.5.5.1 FPT_STM_EXT.1 Reliable Time Stamps FPT_STM_EXT.1 Reliable Time Stamps FPT_STM_EXT.1.1 The TSF shall be able to provide reliable time stamps for its own use. FPT_STM_EXT.1.2 The TSF shall [allow the Security Administrator to set the time]. 5.5.6 Self-test Failures (FPT_FLS) 5.5.6.1 FPT_FLS.1/SelfTest Fail Secure 5.5.6.1 FPT_FLS.1/SelfTest Fail Secure 31 FPT_FLS.1.1/SelfTest The TSF shall shut down when the following types of failures occur: [failure of the power-on self-tests, failure of integrity check of the TSF executable image, failure of noise source health tests]. 29 Specified in [VPN_EP]. 30 The wording is taken from [VPN_EP]. 31 Specified in [VPN_EP]. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 43 of 89 5.6 TOE Access (FTA) 5.6.1 TSF-initiated Session Locking (Extended – FTA_SSL_EXT) 5.6.1.1 FTA_SSL_EXT.1 TSF-initiated Session Locking FTA_SSL_EXT.1 TSF-initiated Session Locking32 FTA_SSL_EXT.1.1 The TSF shall, for local interactive sessions, [terminate the session] after a Security Administrator-specified time period of inactivity. 5.6.2 Session locking and termination (FTA_SSL) 5.6.2.1 FTA_SSL.3 TSF-initiated Termination (Refinement) FTA_SSL.3 TSF-initiated Termination33 FTA_SSL.3.1: The TSF shall terminate a remote interactive session after a Security Administrator- configurable time interval of session inactivity. 5.6.2.2 FTA_SSL.4 User-initiated Termination (Refinement) FTA_SSL.4 User-initiated Termination34 FTA_SSL.4.1: The TSF shall allow Administrator-initiated termination of the Administrator’s own interactive session. 5.6.3 TOE access banners (FTA_TAB) 5.6.3.1 FTA_TAB.1 Default TOE Access Banners (Refinement) FTA_TAB.1 Default TOE Access Banners35 FTA_TAB.1.1: Before establishing an administrative user session the TSF shall display a Security Administrator-specified advisory notice and consent warning message regarding use of the TOE. 5.7 Trusted path/channels (FTP) 5.7.1 Trusted Channel (FTP_ITC) 5.7.1.1 FTP_ITC.1 Inter-TSF trusted channel (Refinement) FTP_ITC.1 Inter-TSF trusted channel36 FTP_ITC.1.1 Refinement: The TSF shall use IPsec, and [SSH] to provide a trusted communication channel between itself and authorized IT entities supporting the following capabilities: audit server, VPN communications, [no other capabilities] that is logically distinct from other communication channels and provides assured identification of its end points and protection of the channel data from disclosure and detection of modification of the channel data37 . FTP_ITC.1.2 The TSF shall permit the TSF or the authorized IT entities to initiate communication via the trusted channel. 32 Specified in [NDcPP] and [FWcPP]. 33 Specified in [NDcPP] and [FWcPP]. 34 Specified in [NDcPP] and [FWcPP]. 35 Specified in [NDcPP] and [FWcPP]. 36 The wording of this element is taken from [VPN_EP] and TD0307. 37 The wording of this element is taken from [VPN_EP]. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 44 of 89 FTP_ITC.1.3 The TSF shall initiate communication via the trusted channel for [VPN communications and streaming of syslog events]. 5.7.2 Trusted Path (FTP_TRP) 5.7.2.1 FTP_TRP.1/Admin Trusted Path (Refinement) FTP_TRP.1/Admin Trusted Path FTP_TRP.1.1/Admin The TSF shall be capable of using [SSH, IPSEC] to provide a communication path between itself and authorized remote Administrators that is logically distinct from other communication paths and provides assured identification of its end points and protection of the communicated data from disclosure and provides detection of modification of the channel data. FTP_TRP.1.2/Admin The TSF shall permit remote Administrators to initiate communication via the trusted path. FTP_TRP.1.3/Admin The TSF shall require the use of the trusted path for initial Administrator authentication and all remote administration actions. 5.8 User Data Protection (FDP) 5.8.1 Residual information protection (FDP_RIP) 5.8.1.1 FDP_RIP.2 Full Residual Information Protection FDP_RIP.2 Full Residual Information Protection38 FDP_RIP.2.1 The TSF shall ensure that any previous information content of a resource is made unavailable upon the allocation of the resource to] all objects. 5.9 Packet Filtering (FPF) 5.9.1 Packet Filtering Rules (FPF_RUL_EXT) 5.9.1.1 FPF_RUL_EXT.1 Rules for Packet Filtering FPF_RUL_EXT.1 Rules for Packet Filtering39 FPF_RUL_EXT.1.1 The TSF shall perform Packet Filtering on network packets processed by the TOE. FPF_RUL_EXT.1.2 The TSF shall process the following network traffic protocols: • Internet Protocol (IPv4) • Internet Protocol version 6 (IPv6) • Transmission Control Protocol (TCP) • User Datagram Protocol (UDP) and be capable of inspecting network packet header fields defined by the following RFCs to the extent mandated in the other elements of this SFR • RFC 791 (IPv4) • RFC 2460 (IPv6) • RFC 793 (TCP) • RFC 768 (UDP). 38 Specified in [FWcPP]. 39 Specified in [VPN_EP]. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 45 of 89 FPF_RUL_EXT.1.3 The TSF shall allow the definition of Packet Filtering rules using the following network protocol fields: • IPv4 o Source address o Destination Address o Protocol • IPv6 o Source address o Destination Address o Next Header (Protocol) • TCP o Source Port o Destination Port • UDP o Source Port o Destination Port FPF_RUL_EXT.1.4 The TSF shall allow the following operations to be associated with Packet Filtering rules: permit, discard, and log. FPF_RUL_EXT.1.5 The TSF shall allow the Packet Filtering rules to be assigned to each distinct network interface. FPF_RUL_EXT.1.6 The TSF shall process the applicable Packet Filtering rules (as determined in accordance with FPF_RUL_EXT.1.5) in the following order: Administrator-defined. FPF_RUL_EXT.1.7 The TSF shall drop traffic if a matching rule is not identified. 5.10 Firewall (FFW) 5.10.1 Stateful Traffic Filter Firewall (FFW_RUL_EXT) 5.10.1.1 FFW_RUL_EXT.1 Stateful Traffic Filtering FFW_RUL_EXT.1 Stateful Traffic Filtering FFW_RUL_EXT.1.1 The TSF shall perform Stateful Traffic Filtering on network packets processed by the TOE. FFW_RUL_EXT.1.2 The TSF shall allow the definition of Stateful Traffic Filtering rules using the following network protocol fields: • ICMPv4 o Type o Code • ICMPv6 o Type o Code • IPv4 o Source address o Destination Address o Transport Layer Protocol • IPv6 o Source address o Destination Address o Transport Layer Protocol Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 46 of 89 o [no other field] • TCP o Source Port o Destination Port • UDP o Source Port o Destination Port • and distinct interface. FFW_RUL_EXT.1.3 The TSF shall allow the following operations to be associated with Stateful Traffic Filtering rules: permit or drop with the capability to log the operation. FFW_RUL_EXT.1.4 The TSF shall allow the Stateful Traffic Filtering rules to be assigned to each distinct network interface. FFW_RUL_EXT.1.5 The TSF shall a) accept a network packet without further processing of Stateful Traffic Filtering rules if it matches an allowed established session for the following protocols: TCP, UDP, [ICMP] based on the following network packet attributes: 1. TCP: source and destination addresses, source and destination ports, sequence number, Flags; 2. UDP: source and destination addresses, source and destination ports; 3. [ICMP: source and destination addresses, type, [code]]. b) Remove existing traffic flows from the set of established traffic flows based on the following: [session inactivity timeout, completion of the expected information flow]. FFW_RUL_EXT.1.6 The TSF shall enforce the following default Stateful Traffic Filtering rules on all network traffic: a) The TSF shall drop and be capable of [logging] packets which are invalid fragments; b) The TSF shall drop and be capable of [logging] fragmented packets which cannot be re-assembled completely; c) The TSF shall drop and be capable of logging packets where the source address of the network packet is defined as being on a broadcast network; d) The TSF shall drop and be capable of logging packets where the source address of the network packet is defined as being on a multicast network; The TSF shall drop and be capable of logging network packets where the source address of the network packet is defined as being a loopback address; e) The TSF shall drop and be capable of logging network packets where the source or destination address of the network packet is defined as being unspecified (i.e. 0.0.0.0) or an address “reserved for future use” (i.e. 240.0.0.0/4) as specified in RFC 5735 for IPv4; f) The TSF shall drop and be capable of logging network packets where the source or destination address of the network packet is defined as an “unspecified address” or an address “reserved for future definition and use” (i.e. unicast addresses not in this address range: 2000::/3) as specified in RFC 3513 for IPv6; g) The TSF shall drop and be capable of logging network packets with the IP options: Loose Source Routing, Strict Source Routing, or Record Route specified; and h) [no other rules]. FFW_RUL_EXT.1.7 The TSF shall be capable of dropping and logging according to the following rules: a) The TSF shall drop and be capable of logging network packets where the source address of the network packet is equal to the address of the network interface where the network packet was received; Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 47 of 89 b) The TSF shall drop and be capable of logging network packets where the source or destination address of the network packet is a link-local address; c) The TSF shall drop and be capable of logging network packets where the source address of the network packet does not belong to the networks associated with the network interface where the network packet was received. FFW_RUL_EXT.1.8 The TSF shall process the applicable Stateful Traffic Filtering rules in an administratively defined order. FFW_RUL_EXT.1.9 The TSF shall deny packet flow if a matching rule is not identified. FFW_RUL_EXT.1.10 The TSF shall be capable of limiting an administratively defined number of half- open TCP connections. In the event that the configured limit is reached, new connection attempts shall be dropped and the drop event shall be [logged]. 5.10.1.2 FFW_RUL_EXT.2 Stateful Filtering of Dynamic Protocols FFW_RUL_EXT.2 Stateful Filtering of Dynamic Protocols FFW_RUL_EXT.2.1 The TSF shall dynamically define rules or establish sessions allowing network traffic to flow for the following network protocols [FTP]. 5.11 Intrusion Prevention (IPS) 5.11.1 Network Traffic Analysis (IPS_NTA_EXT) 5.11.1.1 Network Traffic Analysis IPS_NTA_EXT.1 Network Traffic Analysis IPS_NTA_EXT.1.1 The TSF shall perform analysis of IP-based network traffic forwarded to the TOE’s sensor interfaces, and detect violations of administratively-defined IPS policies. IPS_NTA_EXT.1.2 The TSF shall process (be capable of inspecting) the following network traffic protocols: • Internet Protocol (IPv4), RFC 791 • Internet Protocol version 6 (IPv6), RFC 2460 • Internet control message protocol version 4 (ICMPv4), RFC 792 • Internet control message protocol version 6 (ICMPv6), RFC 2463 • Transmission Control Protocol (TCP), RFC 793 • User Data Protocol (UDP), RFC 768 IPS_NTA_EXT.1.3 The TSF shall allow the signatures to be assigned to sensor interfaces configured for promiscuous mode, and to interfaces configured for inline mode, and support designation of one or more interfaces as ‘management’ for communication between the TOE and external entities without simultaneously being sensor interfaces. • Promiscuous (listen-only) mode: [none]; • Inline (data pass-through) mode: [Ethernet interfaces]; • Management mode: [Ethernet interfaces, out-of-band management Ethernet interfaces]; o Session-reset-capable interfaces: [Ethernet interfaces]; o and no other interface types]. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 48 of 89 5.11.2 IPS IP Blocking (IPS_IPB_EXT) 5.11.2.1 IP Blocking IPS_IPB_EXT.1 IP Blocking IPS_IPB_EXT.1.1 The TSF shall support configuration and implementation of known-good and known-bad lists of [source, destination] IP addresses. IPS_IPB_EXT.1.2 The TSF shall allow IPS Administrators and [no other roles] to configure the following IPS policy elements: [known-good list rules, known-bad list rules, IP addresses]. 5.11.3 Signature-Based IPS Functionality (IPS_SBD_EXT) 5.11.3.1 Signature-Based IPS IPS_SBD_EXT.1 Signature-Based IPS Functionality IPS_SBD_EXT.1.1 The TSF shall support inspection of packet header contents and be able to inspect at least the following header fields: • IPv4: Version; Header Length; Packet Length; ID; IP Flags; Fragment Offset; Time to Live (TTL); Protocol; Header Checksum; Source Address; Destination Address; IP Options; and [no other field]. • IPv6: Version; payload length; next header; hop limit; source address; destination address; routing header; and [traffic class, flow label]. • ICMP: Type; Code; Header Checksum; and [rest of header (varies based on the ICMP type and code)]]. • ICMPv6: Type; Code; and Header Checksum. • TCP: Source port; destination port; sequence number; acknowledgement number; offset; reserved; TCP flags; window; checksum; urgent pointer; and TCP options. • UDP: Source port; destination port; length; and UDP checksum. IPS_SBD_EXT.1.2 The TSF shall support inspection of packet payload data and be able to inspect at least the following data elements to perform string-based pattern-matching: • ICMPv4 data: characters beyond the first 4 bytes of the ICMP header. • ICMPv6 data: characters beyond the first 4 bytes of the ICMP header. • TCP data (characters beyond the 20 byte TCP header), with support for detection of: i) FTP (file transfer) commands: help, noop, stat, syst, user, abort, acct, allo, appe, cdup, cwd, dele, list, mkd, mode, nlst, pass, pasv, port, pass, quit, rein, rest, retr, rmd, rnfr, rnto, site, smnt, stor, stou, stru, and type. ii) HTTP (web) commands and content: commands including GET and POST, and administrator-defined strings to match URLs/URIs, and web page content. iii) SMTP (email) states: start state, SMTP commands state, mail header state, mail body state, abort state. iv) [no other types of TCP payload inspection]; • UDP data: characters beyond the first 8 bytes of the UDP header; • [no other types of packet payload inspection]; In addition, the TSF shall support stream reassembly or equivalent to detect malicious payload even if it is split across multiple non-fragmented packets. IPS_SBD_EXT.1.3 The TSF shall be able to detect the following header-based signatures (using fields identified in IPS_SBD_EXT.1.1) at IPS sensor interfaces: a) IP Attacks i. IP Fragments Overlap (Teardrop attack, Bonk attack, or Boink attack) Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 49 of 89 ii. ii) IP source address equal to the IP destination (Land attack) b) ICMP Attacks i. Fragmented ICMP Traffic (e.g. Nuke attack) ii. Large ICMP Traffic (Ping of Death attack) c) TCP Attacks i. TCP NULL flags ii. TCP SYN+FIN flags iii. TCP FIN only flags iv. TCP SYN+RST flags d) UDP Attacks i. UDP Bomb Attack ii. UDP Chargen DoS Attack IPS_SBD_EXT.1.4 The TSF shall be able to detect all the following traffic-pattern detection signatures, and to have these signatures applied to IPS sensor interfaces: a) Flooding a host (DoS attack) i. ICMP flooding (Smurf attack, and ping flood) ii. TCP flooding (e.g. SYN flood) b) Flooding a network (DoS attack) c) Protocol and port scanning i. IP protocol scanning ii. TCP port scanning iii. UDP port scanning iv. ICMP scanning IPS_SBD_EXT.1.5 The TSF shall allow the following operations to be associated with signature-based IPS policies: • In any mode, for any sensor interface: [ o allow the traffic flow; o send a TCP reset to the source address of the offending traffic; o send a TCP reset to the destination address of the offending traffic] • In inline mode: o block/drop the traffic flow; o and [allow all traffic flow]40 5.11.4 Anomaly-Based IPS Functionality (IPS_ABD_EXT) 5.11.4.1 IPS_ABD_EXT.1 Anomaly-Based IPS Functionality IPS_ABD_EXT.1 Anomaly-Based IPS IPS_ABD_EXT.1.1 The TSF shall support the definition of [anomaly (‘unexpected’) traffic patterns] including the specification of [ • throughput ([bits per second]); • time of day; • frequency; • thresholds; • [no other methods]] and the following network protocol fields: • [IPv4: source address; destination address 40 Updated per NIAP TD0325 Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 50 of 89 • IPv6: source address; destination address • TCP: source port; destination port • UDP: source port; destination port] IPS_ABD_EXT.1.2 The TSF shall support the definition of anomaly activity through [manual configuration by administrators]. IPS_ABD_EXT.1.3 The TSF shall allow the following operations to be associated with anomaly-based IPS policies: • In any mode, for any sensor interface: [ o allow the traffic flow; o send a send a TCP reset to the source address of the offending traffic; o send a TCP reset to the destination address of the offending traffic] • In inline mode: o allow the traffic flow o block/drop the traffic flow • and [no other actions] Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 51 of 89 6 Security Assurance Requirements 58. The TOE security assurance requirements are taken from [NDcPP] , together with the refinements documented in [NDcPP] Section 7, as listed in Table 6 below. Assurance Class Assurance Component Security Target (ASE) Conformance claims (ASE_CCL.1) Extended components definition (ASE_ECD.1) ST introduction (ASE_INT.1) Security objectives for the operational environment (ASE_OBJ.1) Stated security requirements (ASE_REQ.1) Security Problem Definition (ASE_SPD.1) Development (ADV) TOE summary specification (ASE_TSS.1) Guidance documents (AGD) Basic functional specification (ADV_FSP.1) Operational user guidance (AGD_OPE.1) Life cycle support (ALC) Preparative procedures (AGD_PRE.1) Labelling of the TOE (ALC_CMC.1) TOE CM coverage (ALC_CMS.1) Tests (ATE) Independent testing – conformance (ATE_IND.1) Vulnerability assessment (AVA) Vulnerability survey (AVA_VAN.1) Table 6 Security Assurance Requirements Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 52 of 89 7 TOE Summary Specification 7.1 Protected communications 59. Local console access is gained by connecting an RJ-45 cable between the console port on the appliance and a workstation with a serial connection client. 7.1.1 Algorithms and zeroization 60. All FIPS-approved cryptographic functions implemented by the secure network appliance are implemented in the following libraries: • Authentec (for IKE Daemon and DRBG for all daemons) Control plane • OpenSSL (for SSH and the PKI daemons, and DRBG for all daemons) in Control Plane • OpenSSH (for SSH Daemon) Control Plane • Kernel (veriexec) Control Plane. 61. All random number generation by the TOE is performed in accordance with NIST Special Publication 800-90 using HMAC_DRBG implemented in the OpenSSL library (FCS_RBG_EXT.1.1). Additionally, SHA (256,512) is implemented in the LibMD library which is used for password hashing by Junos’ MGD daemon. The network appliance is to be operated with FIPS mode enabled. 62. The TOE evaluation provides a CAVP validation certificate for all FIPS-approved cryptographic functions implemented by the TOE. CAVP certificate details are provided in Table 7. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 53 of 89 Module Crypto Module/ Library FIPS PUB Algorithm, Mode, Keysize, Function, Hashing, Usage Certificate Number SRX300, SRX320 SRX340, SRX345, SRX-345-DUAL-AC SRX550M Processor Processor Processor SPU: Data Plane Data plane – IPSec Daemon FIPS 197, SP 800-38D AES-GCM (128, 192, 256) (Encrypt, Decrypt, AEAD) C1109 Cavium Octeon III (CN7020) w/ internal accelerators (HW/FW) Cavium Octeon III (CN7130) w/ internal accelerators (HW/FW) Cavium Octeon II (CN6335) w/ internal accelerators (HW/FW) FIPS 197, SP 800-38A AES-CBC (128, 192, 256) (Encrypt, Decrypt) C1109 Cavium Octeon III (CN7020) w/ internal accelerators (HW/FW) Cavium Octeon III (CN7130) w/ internal accelerators (HW/FW) Cavium Octeon II (CN6335) w/ internal accelerators (HW/FW) FIPS 180-4 SHS: SHA (256) Byte Oriented (Message Digest Generation) C1109 Cavium Octeon III (CN7020) w/ internal accelerators (HW/FW) Cavium Octeon III (CN7130) w/ internal accelerators (HW/FW) Cavium Octeon II (CN6335) w/ internal accelerators (HW/FW) FIPS 198-1 HMAC-SHA (256) Byte Oriented (Message Authentication) C1109 Cavium Octeon III (CN7020) w/ internal accelerators (HW/FW) Cavium Octeon III (CN7130) w/ internal accelerators (HW/FW) Cavium Octeon II (CN6335) w/ internal accelerators (HW/FW) SPU: Control Plane Quicksec – IKED Daemon FIPS 197, SP 800-38A AES-CBC (128, 192, 256) (Encrypt, Decrypt) C1084 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) FIPS 197, SP 800-38D AES-GCM (128, 256) (Encrypt, Decrypt, AEAD) C1084 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) FIPS 180-4 SHS: SHA (256, 384) Byte Oriented (Message Digest Generation) C1084 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) FIPS 198-1 HMAC-SHA (256,384) C1084 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 54 of 89 Module Crypto Module/ Library FIPS PUB Algorithm, Mode, Keysize, Function, Hashing, Usage Certificate Number SRX300, SRX320 SRX340, SRX345, SRX-345-DUAL-AC SRX550M Processor Processor Processor SP 800- 135 CVL IKE v1/v2 KDF (SHA-256, SHA-384) C1084 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) RE: Control Plane Quicksec – All Daemons SP 800- 90A DRBG (HMAC-SHA- 256) (Random Bit Generation) C1084 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) SPU: Control Plane Octeon – IKED Daemon FIPS 186-4 RSA PKCS1_V1_5 (n=2048 (SHA 256), n=4096 (SHA 256)) (SigGen, SigVer) C1151 Cavium Octeon III (CN7020) w/ internal accelerators (HW/FW) - Partly accelerated Cavium Octeon III (CN7130) w/ internal accelerators (HW/FW) - Partly accelerated Cavium Octeon II (CN6335) w/ internal accelerators (HW/FW) - Partly accelerated FIPS 186-4 ECDSA (P-256 w/ SHA-256) ECDSA (P-384 w/ SHA-384) (SigGen, SigVer, KeyGen for ECDH) C1151 Cavium Octeon III (CN7020) w/ internal accelerators (HW/FW) - Partly accelerated Cavium Octeon III (CN7130) w/ internal accelerators (HW/FW) - Partly accelerated Cavium Octeon II (CN6335) w/ internal accelerators (HW/FW) - Partly accelerated RE: Control Plane OpenSSL/Octeon IKED Daemon SP 800- 56 A CVL (DH Group 24). C1112 Cavium Octeon III (CN7020) w/ internal accelerators (HW/FW) - Partly accelerated Cavium Octeon III (CN7130) w/ internal accelerators (HW/FW) - Partly accelerated Cavium Octeon II (CN6335) w/ internal accelerators (HW/FW) - Partly accelerated SP 800- 56 A CVL / KASVS ECC (DH Groups 19 and 20). C1113 Cavium Octeon III (CN7020) w/ internal accelerators (HW/FW) - Partly accelerated Cavium Octeon III (CN7130) w/ internal accelerators (HW/FW) - Partly accelerated Cavium Octeon II (CN6335) w/ internal accelerators (HW/FW) - Partly accelerated Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 55 of 89 Module Crypto Module/ Library FIPS PUB Algorithm, Mode, Keysize, Function, Hashing, Usage Certificate Number SRX300, SRX320 SRX340, SRX345, SRX-345-DUAL-AC SRX550M Processor Processor Processor RE: Control Plane OpenSSL – SSHD Daemon and PKID Daemon FIPS 197, SP800- 38A AES-CBC/CTR (128, 192, 256) (Encrypt, Decrypt) C1107 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) FIPS 180-4 SHS: SHA (1, 256, 384, 512) Byte Oriented (Message Digest Generation, KDF Primitive) C1107 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) FIPS 198-1 HMAC-SHA (1, 256, 512) Byte Oriented (Message Authentication DRBG Primitive) C1107 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) FIPS 186-4 RSA PKCS1_V1_5 (n=2048 (SHA-256), n=4096 (SHA-256)) (SigGen, SigVer) C1107 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) FIPS 186-4 RSA X931 (n=2048 (SHA-256), n=4096 (SHA-256)) (KeyGen) C1107 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 56 of 89 Module Crypto Module/ Library FIPS PUB Algorithm, Mode, Keysize, Function, Hashing, Usage Certificate Number SRX300, SRX320 SRX340, SRX345, SRX-345-DUAL-AC SRX550M Processor Processor Processor FIPS 186-4 ECDSA [P-256 (SHA- 256)], [P-384 (SHA- 384)], [P-521 (SHA- 512)] (SigGen, SigVer, KeyGen) C1107 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) SP 800- 56 A ECDH (CVL/KASVS ECC, ECDH Groups 19, 20, 21) C1113 Cavium Octeon III (CN7020) w/ internal accelerators (HW/FW) - Partly accelerated Cavium Octeon III (CN7130) w/ internal accelerators (HW/FW) - Partly accelerated Cavium Octeon II (CN6335) w/ internal accelerators (HW/FW) - Partly accelerated RE: Control Plane OpenSSL – All Daemons SP 800- 90A DRBG (HMAC-SHA-2- 256) (Random Bit Generation) C1107 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) RE: Control Plane OpenSSH – SSHD Daemon SP 800- 135 CVL SSH v2 KDF (SHA 1, SHA-256, SHA-384) (Key Derivation) C1111 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) RE: Control Plane Libmd - MGD Daemon, Password Hashing FIPS 180-4 SHS: SHA (1, 256) Byte Oriented (Message Digest Generation) C1052 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) FIPS 198-1 HMAC-SHA (256) Byte Oriented Message Digest Generation) C1052 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 57 of 89 Module Crypto Module/ Library FIPS PUB Algorithm, Mode, Keysize, Function, Hashing, Usage Certificate Number SRX300, SRX320 SRX340, SRX345, SRX-345-DUAL-AC SRX550M Processor Processor Processor RE: Control Plane Kernel – Veriexec, kernel DRBG SP800- 90A DRBG (HMAC-SHA-2- 256) (Random Bit Generation) C1079 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) FIPS 198-1 HMAC-SHA (256) Byte Oriented (DRBG Primitive) C1079 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) FIPS 180-4 SHS: SHA (1, 256) Byte Oriented (Message Digest Generation) C1079 Cavium Octeon III (CN7020) (FW) Cavium Octeon III (CN7130) (FW) Cavium Octeon II (CN6335) (FW) Table 7 CAVP Certificate Results for Cryptographic Services Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 58 of 89 63. The FIPS approved algorithms are applied when the FIPS operating mode is enabled41 . (FCS_COP.1/DataEncryption, FCS_COP.1/SigGen, FCS_COP.1/Hash, FCS_COP.1/KeyedHash, FCS_RBG_EXT.1, FCS_CKM.1, FMT_SMF.1) 64. Asymmetric keys are generated in accordance with NIST SP 800-56A and FIPS PUB 186-4 for IKE with IPSec. The TOE complies with section 5.6 of NIST SP 800-56A regarding asymmetric key pair generation. The TOE implements all of the "shall" and "should" requirements and none of the "shall not" or "should not" from FIPS PUB 186-4 Appendix B3 and B4. (FCS_CKM.1/IKE) 65. Asymmetric keys are also generated in accordance with FIPS PUB 186-4 Appendix B.3 for RSA Schemes and Appendix B.4 for ECC Schemes for SSH communications. The TOE implements Diffie-Hellman group 14, using the modulus and generator specified by Section 3 of RFC3526. (FCS_CKM.2, FCS_CKM.1/ND). 66. The following table relates cryptographic algorithms to the protocols by the TOE. The TOE acts as both sender and recipient for IPsec and only as the server for SSH in the supported protocols listed in Table 8: The integrity algorithm HMAC-SHA-1 uses key length 160 bits, block size 512 bits and output size 160 bits. HMAC-SHA-256 uses key length 256 bits, block size 512 bits and output size 256 bits. Protocol Key Exchange Auth Cipher Integrity IKEv1 Group 14 (modp 2048) Group 19 (P-256) Group 20 (P-384) Group 24 (modp 2048) RSA 2048, RSA 4096 ECDSA P-256 ECDSA P-384 Pre-Shared Key AES CBC 128 AES CBC 192 AES CBC 256 HMAC-SHA-256 HMAC-SHA-384 IKEv2 Group 14 (modp 2048) Group 19 (P-256) Group 20 (P-384) Group 24 (modp 2048) RSA 2048, RSA 4096 ECDSA P-256 ECDSA P-384 Pre-Shared Key AES CBC 128 AES CBC 192 AES CBC 256 AES GCM 128 AES GCM 256 HMAC-SHA-256 HMAC-SHA-384 IPsec ESP IKEv1 with optional: Group 14 (modp 2048) Group 19 (P-256) Group 20 (P-384) Group 24 (modp 2048) IKEv1 AES CBC 128 AES CBC 192 AES CBC 256 HMAC-SHA-256-128 IKEv2 with optional: Group 14 (modp 2048) Group 19 (P-256) Group 20 (P-384) Group 24 (modp 2048) IKEv2 AES CBC 128 AES CBC 192 AES CBC 256 AES GCM 128 AES GCM 192 AES GCM 256 HMAC-SHA-256-128 SSHv2 DH Group 14 (modp 2048) ECDH-sha2-nistp256 ECDH-sha2-nistp384 ECDH-sha2-nistp521 ECDSA P-256 ECDSA P-384 ECDSA P-521 ssh_rsa AES CTR 128 AES CTR 256 AES CBC 128 AES CBC 256 HMAC-SHA-1 HMAC-SHA-256 HMAC-SHA-512 Table 8 Supported Protocols 41 The knob “set system fips level 1” will enforce strict compliance to FIPS and enable restrictions on algorithms and keys sizes as required by FIPS requirements. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 59 of 89 67. The TOE acts as both sender and recipient for IPsec and only as the server for SSH in the supported protocols listed in Table 8. The TOE implements Diffie-Hellman group 14, using the modulus and generator specified by Section 3 of RFC3526. (FCS_CKM.2) 68. Junos OS handles zeroization for all CSP, plaintext secret and private cryptographic keys according to Table 9 below. (FCS_CKM.4). Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 60 of 89 CSP Description Method of storage Storage location Zeroization Method SSH Private Host Key The first time SSH is configured, the set of Host keys is generated. Used to identify the host. ecdsa-sha2-nistp256 (ECDSA P‐256) and/or ssh-rsa (RSA 2048) Plaintext File format on SDD) When the appliance is recommissioned, the config files (including CSP files such as SSH keys) are removed using the “request system zeroize” option. Loaded into memory to complete session establishment Plaintext Memory Memory free() operation is performed by Junos upon session termination SSH Session Key Session keys used with SSH, AES 128, 256, hmac-sha-1 or hmac- sha2-256, hmac-sha2- 512, DH Private Key (2048 or elliptic curve 256/384/521-bits) Plaintext Memory Memory free() operation is performed by Junos upon session termination User Password Plaintext value as entered by user Plaintext as entered Processed in Memory Memory free() operation is performed by Junos upon completion of authentication Hashed when stored (HMAC- sha1, sha256, sha512) Stored on disk When the appliance is recommissioned, the config files (including the obfuscated password) are removed using the “request system zeroize” option. RNG State Internal state and seed key of RNG Plaintext Memory Handled by kernel, overwritten with zero’s at reboot. IKE Private Host key Private authentication key used in IKE. RSA 2048, RSA 4096, ECDSA P‐256, ECDSA P‐384 Plaintext Disk/Memory ‘clear security IKE security- association’ command or reboot the box. Private keys stored in flash are not zeroized unless an explicit “request system zeroize” is executed. IKE‐ SKEYID IKE master secret used to derive IKE and IPsec ESP session keys Plaintext Memory ‘clear security IKE security- association’ command or reboot the box Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 61 of 89 CSP Description Method of storage Storage location Zeroization Method IKE Session Keys IKE session key. AES, HMAC Plaintext Memory ‘clear security IKE security- association’ command or reboot the box ESP Session Key ESP session keys. AES, HMAC Plaintext Memory ‘clear security ipsec security-association’ or reboot the box. IKE‐DH Private Exponent Ephemeral DH private exponent used in IKE. DH N = 224, 256 bit, ECDH P‐256, or ECDH P‐ 384. Plaintext Memory ‘clear security IKE security- association’ command or reboot the box. IKE‐PSK Pre-shared authentication key used in IKE. Hashed Disk/Memory ‘clear security IKE security- association’ command or reboot the box. Key values stored in flash are not zeroized unless an explicit “request system zeroize” is executed. ecdh private keys Loaded into memory to complete key exchange in session establishment Plaintext Memory Memory free() operation is performed by Junos upon session termination Table 9 CSP Storage and Zeroization 69. Junos OS does not provide a CLI interface to permit the viewing of keys. Cryptographic keys are protected through the enforcement of kernel-level file access rights, limiting access to the contents of cryptographic key containers to processes with cryptographic rights or shell users with root permission42 . (FPT_SKP_EXT.1) 7.1.2 Random Bit Generation 70. Junos OS performs random bit generation in accordance with NIST Special Publication 800-90 using HMAC_DRBG, SHA-256. The RBG is seeded from both software and hardware sources. The SRX3xx and SRX550-M Services Gateway appliances rely on RANDOM_NET and RANDOM_PURE (Cavium Oscillators) as sources of entropy: • RANDOM_NET: This source of entropy is associated with network activity. Timings (CPU counter values at the time of the network event) together with internal representation of network packets are harvested and fed to Kernel HMAC DRBG. This source of entropy can be stimulated from outside of Junos device's security boundary. The entropy claimed is 3 bits per harvesting event. On interrupt from network DMA, 96 bits from internal packet representation buffer + 32 unsigned 32 bit cpu cycle counter (promoted to unsigned 64 bit counter). • RANDOM_PURE: This source of entropy is associated with the hardware random number generators of the Cavium Octeon III CN7130, Octeon III CN7020 and Octeon II CN6335. The 42 Security Administrators do not have root permission in shell. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 62 of 89 output of this RNG is used to periodically seed Kernel HMAC DRBG. This source of entropy cannot be stimulated from outside of Junos device's security boundary. The entropy claimed is 16 bits per harvesting event. Sample from two reads of Cavium RNG along with cycle count. Unsigned 32 bit CPU counter is promoted to unsigned 64 bit counter. 7.1.3 SSH 71. Junos OS supports and enforces Trusted Channels that protect the communications between the TOE and a remote audit server from unauthorized disclosure or modification. It also supports Trusted Paths between itself and remote administrators so that the contents of administrative sessions are protected against unauthorized disclosure or modification. (FTP_ITC.1, FTP_TRP.1/Admin) 72. Junos OS provides an SSH server to support Trusted Channels using SSHv2 protocol which ensures the confidentiality and integrity of communication with the remote audit server. Export of audit information to a secure, remote server is achieved by setting up an event trace monitor that sends event log messages by using NETCONF over SSH to the remote system event logging server. The remote audit server initiates the connection. The SSHv2 protocol ensures that the data transmitted over a SSH session cannot be disclosed or altered by using the encryption and integrity mechanisms of the protocol with the FIPS cryptographic module. (FTP_ITC.1, FCS_SSHS_EXT.1) 73. The Junos OS SSH Server also supports Trusted Paths using SSHv2 protocol which ensures the confidentiality and integrity of user sessions. The encrypted communication path between Junos OS SSH Server and a remote administrator is provided by the use of an SSH session. Remote administrators of Junos OS initiate communication to the Junos CLI through the SSH tunnel created by the SSH session. Assured identification of Junos OS is guaranteed by using public key based authentication for SSH. The SSHv2 protocol ensures that the data transmitted over a SSH session cannot be disclosed or altered by using the encryption and integrity mechanisms of the protocol with the FIPS cryptographic module. If desired, an additional layer of protection can be afforded to the trusted path by using IPSec to encapsulate the SSH connection. (FTP_TRP.1/Admin, FCS_SSHS_EXT.1) 74. The Junos OS SSH server is implemented in accordance with RFCs 4251, 4252, 4253, 4254, 5656 and 6668. Junos OS provides assured identification of the Junos OS appliance though public key authentication and supports password-based authentication by administrative users (Security Administrator) for SSH connections. The following table identifies conformance to the SSH related RFCs: Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 63 of 89 RFC Summary TOE implementation of Security RFC 4251 The Secure Shell (SSH) Protocol Architecture Host Keys: The TOE uses an ECDSA Host Key for SSH v2, with a key size of 256 bits or greater, which is generated on initial setup of the TOE. It can be de-configured via the CLI and the key will be deleted and thus unavailable during connection establishment. This key is randomly generated to be unique to each TOE instance. The TOE presents the client with its public key and the client matches this key against its known_hosts list of keys. When a client connects to the TOE, the client will be able to determine if the same host key was used in previous connections, or if the key is different (per the SSHv2 protocol). Junos OS also supports RSA-based key establishment schemes with a key size of 2048 bits. Policy Issues: The TOE implements all mandatory algorithms and methods. The TOE can be configured to accept public-key based authentication and/or password-based authentication. The TOE does not require multiple authentication mechanisms for users. The TOE allows port forwarding and sessions to clients. The TOE has no X11 libraries or applications and X11 forwarding is prohibited. Confidentiality: The TOE does not accept the “none” cipher. supports AES-CBC-128, AES-CBC-256, AES-CTR-128, AES-CTR-256 encryption algorithms for protection of data over SSH and uses keys generated in accordance with “ssh-rsa”, “ecdsa-sha2- nistp256”, “ecdsa-sha2-nistp384” or “ecdsa-sha2-nistp521” to perform public-key based device authentication. For ciphers whose blocksize >= 16, the TOE rekeys every (2^32-1) bytes. The client may explicitly request a rekeying event as a valid SSHv2message at any time and the TOE will honor this request. Re-keying of SSH session keys can be configured using the sshd_config knob. The data-limit must be between 51200 and 4294967295 (2^32-1) bytes and the time-limit must be between 1 and 1440 minutes. In the evaluated deployment the time-limit must be set within 1 and 60 minutes. Denial of Service: When the SSH connection is brought down, the TOE does not attempt to re-establish it. Ordering of Key Exchange Methods: Key exchange is performed only using one of the supported key exchange algorithms, which are ordered as follows: ecdh-sha2-nistp256, ecdh-sha2-nistp384, ecdh-sha2-nistp521 (all specified in RFC 5656), diffie-hellman- group14-sha1 (specified in RFC 4253). Debug Messages: The TOE sshd server does not support debug messages via the CLI. End Point Security: The TOE permits port forwarding. Proxy Forwarding: The TOE permits proxy forwarding. X11 Forwarding: The TOE does not support X11 forwarding. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 64 of 89 RFC Summary TOE implementation of Security RFC 4252 The Secure Shell (SSH) Authentication Protocol Authentication Protocol: The TOE does not accept the “none” authentication method. The TOE implements a timeout period of 30seconds for authentication of the SSHv2 protocol and provides a limit of three failed authentication attempts before sending a disconnect to the client. Authentication Requests: The TOE does not accept authentication if the requested service does not exist. The TOE does not allow authentication requests for a non-existent username to succeed – it sends back a disconnect message as it would for failed authentications and hence does not allow enumeration of valid usernames. The TOE denies “none” authentication method and replies with a list of permitted authentication methods. Public Key Authentication Method: The TOE supports public key authentication for SSHv2 session authentication. The SSH client authenticates the identity of the SSH server using a local database associating each host name with its corresponding public key. Authentication succeeds if the correct private key is used. The TOE does not require multiple authentications (public key and password) for users. Password Authentication Method: The TOE supports password authentication. Expired passwords are not supported and cannot be used for authentication. Host-Based Authentication: The TOE does not support the configuration of host-based authentication methods. RFC 4253 The Secure Shell (SSH) Transport Layer Protocol Encryption: The TOE offers the following for encryption of SSH sessions: aes128-cbc and aes256-cbc, aes128-ctr, aes256-ctr. The TOE permits negotiation of encryption algorithms in each direction. The TOE does not allow the “none” algorithm for encryption. Maximum Packet length: Packets greater than 256Kbytes in an SSH transport connection are dropped and the connection is terminated by Junos OS. Data Integrity: The TOE permits negotiation of HMAC-SHA1 in each direction for SSH transport. Key Exchange: The TOE supports diffie-hellman-group14-sha1. Key Re-Exchange: The TOE performs a re-exchange when SSH_MSG_KEXINIT is received. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 65 of 89 RFC Summary TOE implementation of Security RFC 4254 Secure Shell (SSH) Connection Protocol Multiple channels: The TOE assigns each channel a number (as detailed in RFC 4251, see above). Data transfers: The TOE supports a maximum window size of 256K bytes for data transfer. Interactive sessions: The TOE only supports interactive sessions that do NOT involve X11 forwarding. Forwarded X11 connections: This is not supported in the TOE. Environment variable passing: The TOE only sets variables once the server process has dropped privileges. Starting shells/commands: The TOE supports starting one of shell, application program or command (only one request per channel). These will be run in the context of a channel, and will not halt the execution of the protocol stack. Window dimension change notices: The TOE will accept notifications of changes to the terminal size (dimensions) from the client. Port forwarding: This is fully supported by the TOE. RFC5656 SSH ECC Algorithm Integration ECDH Key Exchange: The support key exchange methods specified in this RFC are ecdh-sha2-nistp256 or ecdh-sha2- nistp384 and ecdh-sha2-nistp521. The client matches the key against its known_hosts list of keys. Hashing: Junos OS supports cryptographic hashing via the SHA- 256 algorithm, provided it has a message digest size of 256 bits.Required Curves: All required curves are implemented: ecdh-sha2-nistp256, ecdh-sha2-nistp384 and ecdh-sha2- nistp521. None of the Recommended Curves are supported as they are not included in [NDcPP]. RFC 6668 sha2-Transport Layer Protocol Data Integrity Algorithms: Both the recommended and optional algorithm hmac-sha2-256 and hmac-sha2-512 are implemented for SSH transport. Table 10 SSH RFC conformance 75. Certificates are stored in non-volatile flash memory. Access to flash memory requires administrator credentials. A certificate may be loaded via command line (FIA_X.509_EXT.1). 7.1.4 IPsec 76. The TOE is conformant to RFC 4301. (FCS_IPSEC_EXT.1.1) 77. The TOE supports tunnel mode only. (FCS_IPSEC_EXT.1.3) 78. By default, the TOE denies all traffic through an SRX Series device. In fact, an implicit default security policy exists that denies all packets. You can change this behavior by configuring a standard security policy that permits certain types of traffic. The implicit default policy can be changed to permit all traffic with the 'set security policies default-policy' command; however, this is not recommended. 79. The security policy rule set is an ordered list of security policy entries enforced by the firewall rules, each of which contains the specification of a network flow and an action: • Source IP address and network mask • Destination IP address and network mask • Protocol Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 66 of 89 • Source port • Destination port • Action: permit, deny, drop silently, log 80. Each packet is compared against entries in the security policy ruleset in sequential order until one is found that matches the specification in the policy, or until the end of the rule set is reached, in which case the implicit default policy is implemented and the packet is discarded. (FCS_IPSEC_EXT.1.2, supported by FPF_RUL_EXT.1.1, FPF_RUL_EXT.1.3, FPF_RUL_EXT.1.4, FPF_RUL_EXT.1.6, FPF_RUL_EXT.1.7) 81. The TOE supports AES-GCM-128, AES-GCM-192 and AES-GCM-256, and AES-CBC-128, AES-CBC- 192 or AES-CBC-256 using HMAC SHA-256 for ESP protection. (FCS_IPSEC_EXT.1.4) 82. IKEv1 and IKEv2 are implemented. IKEv1 as defined in RFCs 2407, 2408, 2409, RFC 4109 and RFC 4868 for hash functions; IKEv2 as defined in RFCs 5996 (with no support for NAT traversal) and RFC 4868 for hash functions. IKEv1 aggressive mode is not supported. (FCS_IPSEC_EXT.1.5) 83. The TOE supports AES-CBC-128, AES-CBC-192, AES-CBC-256, AES-GCM-128 and AES-GCM-256 for payload protection in IKEv1 and IKEv2. (FCS_IPSEC_EXT.1.6) 84. In the evaluated configuration, the TOE permits configuration of the IKE and IPsec lifetime exchanges in terms of number of (kilo)bytes (64 to 4294967294 kilo bytes) or length of time (180 to 86400 seconds): (FCS_IPSEC_EXT.1.7, FCS_IPSEC_EXT.1.8) 85. The following CLI commands configure a lifetime of either kilobytes or seconds: (FCS_IPSEC_EXT.1.7, FCS_IPSEC_EXT.1.8) set security ipsec proposal lifetime-kilobytes set security ipsec proposal lifetime-seconds 86. The TOE supports Diffie-Hellman Groups 14, 19, 20 and 24. In the IKEv1 phase 1 and phase 2 exchanges, the TOE and peer will agree on the best DH group both can support. When the TOE receives an IKE proposal, it will select the first DH group that matches the acceptable DH groups configured in the TOE (one or more of DH Groups 14, 19, 20 or 24) and the negotiation will fail if there is no match. Similarly, when the peer initiates the IKE protocol, the TOE will select the first match from the IKE proposal sent by the peer and the negotiation fails is no acceptable match is found. (FCS_IPSEC_EXT.1.11) 87. The TOE uses HMAC DRBG with SHA-256 for the generation of DH exponents and nonces in the IKE key exchange protocol of length 224 bits (for DH Group 14), 256 bits (for DH Groups 19 and 24) and 384 bits (for DH Group 20). (FCS_IPSEC_EXT.1.9, FCS_IPSEC_EXT.1.10) 88. The TOE supports both RSA and ECDSA for use with X.509v3 certificates that conform to RFC 4945 and pre-shared Keys for IPsec support. (FCS_IPSEC_EXT.1.13) 89. The TOE ensures that the strength of the symmetric algorithm (128, 192 or 256 bits) negotiated to protect the IKEv1 Phase 1, IKEv2 IKE_SA connection is greater than or equal to the strength of the symmetric algorithm negotiated to protect the IKEv1 Phase 2, IKEv2 CHILD_SA connection. (FCS_IPSEC_EXT.1.12) 90. The TOE uses pre-shared keys for IPSec. The TOE accepts ASCII pre-shared or bit-based keys of 1 to 255 characters (and their binary equivalent) that may contain upper and lower case letters, numbers, and special characters (that include: “!”, “@”, “#”, “$”, “%”, “^”, “&”, “*”, “(“, and “)”. The TOE accepts pre-shared text keys and converts the text string into an authentication value as per RFC 2409 for IKEv1 or RFC 4306 for IKEv2, using the PRF that is configured as the hash algorithm for the IKE exchanges. (FIA_PSK_EXT.1). Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 67 of 89 91. The TOE uses X.509 certificates as defined in RFC 5280. 92. To generate a Certificate Request, the administrator uses the CLI command request security pki generate-certificate-request 93. and supplies the following values: • Certificate-id – The internal identifier string for this certificate • Domain-name • Email address • IP address • Subject (DC=,CN=,OU=,O=,SN=,L=,ST=,C=) • Filename – The local file in which to store the certificate signing request (FIA_X509_EXT.3) 94. To validate certificates, the TOE extracts the subject, issuer, subjects public key, signature, basicConstraints and validity period fields. If any of those fields is not present, the validation fails. The issuer is looked up in the PKI database. If the issuer is not present, or if the issuer certificate does not have the CA:true flag in the basicConstraints section, the validation fails. The TOE verifies the validity of the signature. If the signature is not valid, the validation fails. It then confirms that the current date and time is within the valid time period specified in the certificate. The TOE also extracts the extendedKeyUsage field and verifies the value represents that for the Code Signing purpose (id-kp 3 with OID 1.3.6.1.5.5.7.3.3). 95. If the TOE is configured to perform a revocation check using CRL (as specified in RFC 5280 Section 6.3) and the CRL fails to download, there are two possible outcomes: If the TOE is configured with the option to skip CRL checking on download failure enabled, then the certificate shall be considered as having passed the validation. If the TOE is configured with the option to skip CRL checking on download failure disabled, then the certificate is considered to have failed validation. 96. The TOE validates a certificate path by building a chain of (at least 3) certificates based upon issuer and subject linkage, validating each according the certificate validation procedure described above. If any certificate in the chain fails validation, the validation fails as a whole. A self-signed certificate is not required to be at the root of the certificate chain. 97. The TOE determines if a certificate is a CA certificate by requiring the CA:true flag to be present in the basicConstraints section. (FIA_X509_EXT.1.1/Rev) 98. The TOE requires that the configured IKE identity of the local and remote endpoints to match the contents of the certificate associated with a SA endpoint. The TOE permits the identity to be expressed as distinguished name, fully qualified domain name (FQDN), user FQDN or IP address. If either certificate does not validate, or the contents do not match the configured identity, then the SA will not be established. 99. The PKI daemon on an SRX Series device validates all X509 certificates received from VPN peers during the IKE negotiation. If the TSF cannot establish a connection to determine the validity of a certificate, the SA will not be established unless the administrator of the TOE has explicitly configured the TOE to disable the CRL check in case the connection can not be established. (FIA_X509_EXT.1/Rev, FIA_X509_EXT.2, FIA_PSK_EXT.1, FIA_X509_EXT.3) Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 68 of 89 100. For public key-based authentication of IPsec connections, Junos OS validates the X.509 certificates by extracting the subject, issuer, signature, basicConstraints and validity period fields. If any of those fields is not present, the validation fails. The issuer is looked up in the PKI database. If the issuer CA is not present, or if the issuer certificate does not have the CA:true flag in the basicConstraints section, the validation fails. Junos OS verifies the validity of the signature. If the signature is not valid, the validation fails. It then confirms that the current date and time is within the valid time period specified in the certificate. (FIA_X509_EXT.1/Rev, FIA_X509_EXT.2 101. Junos OS generates Certificate Request Messages as specified in RFC 2986 when validating certificates for IPsec connections. Device-specific information, Common Name, Organization, Organizational Unit, Country and public key details are provided in the CSR. Junos OS validates the chain of certificates from the Root CA when the CA Certificate Response is received. (FIA_X509_EXT.3). 7.2 Administrator Authentication 102. Junos OS enforces binding between human users and subjects. The Security Administrator43 is responsible for provisioning user accounts, and only the Security Administrator can do so. (FMT_SMR.2) 103. Junos users are configured under “system login user” and are exported to the password database ‘/var/etc/master.passwd’. A Junos user is therefore an entry in the password database. Each entry in the password database has fields corresponding to the attributes of “system login user”, including username, (obfuscated) password and login class. 104. The internal architecture supporting Authentication includes an active process, associated linked libraries and supporting configuration data. The Authentication process and library are • login() • PAM Library module 105. Following TOE initialization, the login() process is listening for a connection at the local console. This ‘login’ process can be accessed through either direct connection to the local console or following successful establishment of a remote management connection over SSH, when a login prompt is displayed. 106. This login process identifies and authenticates the user using PAM operations. The login process does two things; it first establishes that the requesting user is whom they claim to be and second provides them with an interactive Junos Command interactive command line interface (CLI). 107. The SSH daemon supports public key authentication by looking up a public key in an authorized keys file located in the directory ‘.ssh’ in the user’s home directory (i.e. ‘~/.ssh/’) and this authentication method will be attempted before any other if the client has a key available (FIA_UIA_EXT.1). The SSH daemon will ignore the authorized keys file if it or the directory ‘.ssh’ or the user’s home directory are not owned by the user or are writeable by anyone else. 108. For password authentication, login() interacts with a user to request a username and password to establish and verify the user’s identity. The username entered by the administrator at the username prompt is reflected to the screen, but no feedback to screen is provided while the entry made by the administrator at the password prompt until the Enter key is pressed (FIA_UAU.7). login() uses PAM Library calls for the actual verification of this data. The password is hashed and compared to the stored value, and success/failure is indicated to login(), (FIA_UIA_EXT.1). PAM is used in the TOE support authentication management, account management, session management and password management. Login primarily uses the session management and password management functionality offered by PAM. 43 The Security Administrator role is detailed in Section 7.6 below. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 69 of 89 109. The retry-options can be configured to specify the action to be taken if the administrator fails to enter valid username/password credentials for password authentication when attempting to authenticate via remote access. The retry-options are applied following the first failed login attempt for a given username (FIA_AFL.1). The length of delay (5-10 seconds) after each failed attempt is specified by the backoff-factor, and the increase of the delay for each subsequent failed attempt is specified by the backoff-threshold (1-3). The tries-before-disconnect sets the maximum number of times (1-10) the administrator is allowed to enter a password to attempt to log in to the device through SSH before the connection is disconnected. The lockout-period sets the amount of time in minutes before the administrator can attempt to log in to the device after being locked out due to the number of failed login attempts (1-43,200 minutes). It is also possible for another administrator to “unlock” the account of administrator whose account has been locked for a period of time following failed authentication attempts. Even when an account is blocked for remote access to the TOE, an administrator is always able to login locally through the serial console and the administrator can attempt authentication via remote access after the maximum timeout period of 24 hours. 110. The TOE requires users to provide unique identification and authentication data (passwords/public key) before any access to the system is granted. Prior to authentication, the only Junos OS managed responses provided to the administrator are (FIA_UAU_EXT.2): • Negotiation of SSH session • Display of the access banner • ICMP echo responses. 111. Authentication data for fixed password authentication is a case-sensitive, alphanumeric value. The password has a minimum length of 10 characters and maximum length of 20 characters, and must contain characters from at least two different character sets (upper, lower, numeric, punctuation), and can be up to 20 ASCII characters in length (control characters are not recommended). Any standard ASCII, extended ASCII and Unicode characters can be selected when choosing a password. (FIA_PMG_EXT.1) 112. Locally stored authentication credentials are protected (FPT_APW_EXT.1): • The passwords are stored in obfuscated form using HMAC-sha1. • Authentication data for public key-based authentication methods are stored in a directory owned by the user (and typically with the same name as the user). This directory contains the files ‘.ssh/authorized_keys’ and ‘.ssh/authorized_keys2’ which are used for SSH public key authentication. 113. Junos enables Security Administrators to configure an access banner provided with the authentication prompt. The banner can provide warnings against unauthorized access to the TOE as well as any other information that the Security Administrator wishes to communicate. (FTA_TAB.1) 114. User sessions (local and remote) can be terminated by users (FTA_SSL.4). The administrative user can logout of existing session by typing logout to exit the CLI admin session and the Junos OS makes the current contents unreadable after the admin initiates the termination. No user activity can take place until the user re-identifies and authenticates. 115. The Security Administrator can set the TOE so that a user session is terminated after a period of inactivity. (FTA_SSL_EXT.1, FTA_SSL.3) For each user session Junos OS maintains a count of clock cycles (provided by the system clock) since last activity. The count is reset each time there is activity related to the user session. When the counter reaches the number of clock cycles equating to the configured period of inactivity the user session is locked out. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 70 of 89 116. Junos OS overwrites the display device and makes the current contents unreadable after the local interactive session is terminated due to inactivity, thus disabling any further interaction with the TOE. This mechanism is the inactivity timer for administrative sessions. The Security Administrator can configure this inactivity timer on administrative sessions after which the session will be logged out. 7.3 Correct Operation 117. Junos OS runs the following set of self-tests during power on to check the correct operation of the Junos OS firmware (FPT_TST_EXT.1): • Power on test – determines the boot-device responds, and performs a memory size check to confirm the amount of available memory. • File integrity test –verifies integrity of all mounted signed packages, to assert that system files have not been tampered with. To test the integrity of the firmware, the fingerprints of the executables and other immutable files are regenerated and validated against the SHA1 fingerprints contains in the manifest file. • Crypto integrity test – checks integrity of major CSPs, such as SSH hostkeys and iked credentials, such as Cas, CERTS, and various keys. • Authentication error – verifies that veriexec is enabled and operates as expected using /opt/sbin/kats/cannot-exec.real. • Kernel, libmd, OpenSSL, QuickSec, SSH Ipsec – verifies correct output from known answer tests for appropriate algorithms. 118. Juniper Networks devices run only binaries supplied by Juniper Networks. Within the package, each Junos OS firmware image includes fingerprints of the executables and other immutable files. Junos firmware will not execute any binary without validating a fingerprint. This feature protects the system against unauthorized firmware and activity that might compromise the integrity of the device. These self-tests ensure that only authorized executables are allowed to run thus ensuring the correct operation of the TOE. 119. In the event of a transiently corrupt state or failure condition, the system will panic; the event will be logged and the system restarted, having ceased to process network traffic. When the system restarts, the system boot process does not succeed without passing all applicable self- tests. This automatic recovery and self-test behavior, is discussed in Chapter 11 of [ECG1]. 120. When any self-test fails, the device halts in an error state. No command line input or traffic to any interface is processed. The device must be power cycled to attempt to return to operation. This self-test behavior, is discussed in [ECG1]. (FPT_FLS.1, FPT_TST_EXT.1, FPT_TST_EXT.3) 7.4 Trusted Update 121. Security Administrators are able to query the current version of the TOE firmware using the CLI command “show version”(FPT_TUD_EXT.1) and, if a new version of the TOE firmware is available, initiate an update of the TOE firmware. Junos OS does not provide partial updates for the TOE, customers requiring updates must migrate to a subsequent release. Updates are downloaded and applied manually (there is no automatic updating of the Junos OS). (FPT_TUD_EXT.1, FMT_SMF.1, FMT_MOF.1/ManualUpdate,) 122. The installable software packages have a digital signature that is checked when the Security Administrator attempts to install the package. The signature of the complete package is verified at the beginning of the installation process before the package is expanded. If signature verification fails, an error message is displayed and the package is not installed. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 71 of 89 123. The Junos OS kernel maintains a set of fingerprints (SHA1 digests) for executable files and other files which should be immutable, as described in Section 7.3. The manifest file is signed using the Juniper package signing key, and is verified by the TOE using the public key (stored on the TOE filesystem in clear, protected by filesystem access rights). ECDSA (P-256) with SHA-256 is used for digital signature package verification. 124. The fingerprint loader will only process a manifest for which it can verify the signature. Thus without a valid digital signature an executable cannot be run. When the command is issued to install an update, the manifest file for the update is verified and stored, and each executable/immutable file is verified before it is executed. If any of the fingerprints in an update are not correctly verified, the TOE uses the last known verified image. 125. A certificate may be loaded via command line and is stored in SSD. Access to flash memory requires administrator credentials. Control on access to the trust store holding the X509v3 certificates can be controlled using standard Junos permissions settings. Each top-level CLI command and each configuration statement have an access privilege level associated with them and users can execute only those commands and configure and view only those statements for which they have access privileges. The access privileges for each login class are defined by one or more permission flags. For each login class, the use of operational and configuration mode commands that would otherwise be permitted or not allowed by a privilege level specified in the permissions statement can be explicitly denied or allowed. Cryptographic keys are protected through the enforcement of kernel-level file access rights, limiting access to the contents of cryptographic key containers to processes with cryptographic rights. The TOE does not provide a CLI interface to permit the viewing of keys. (FIA_X.509_EXT.1/Rev, FMT_MTD.1/CoreData). 126. Junos OS verifies the validity of the signature. If the signature is not valid, the validation fails. If the signature is valid the update process proceeds. (FCS_COP.1/SigGen, FPT_TUD_EXT.1,) 7.5 Audit 127. Junos OS creates and stores audit records for the following events (the detail of content recorded for each audit event is detailed in Table 4 (FAU_GEN.1/ND) and Table 5 (FAU_GEN.1/IPS). Auditing is implemented using syslog. • Start-up and shut-down of the audit functions • Administrative login and logout • Configuration is committed • Configuration is changed (includes all management activities of TSF data) • Generating/import of, changing, or deleting of cryptographic keys (see below for more detail) • Resetting passwords • Starting and stopping services • All use of the identification and authentication mechanisms • Unsuccessful login attempts limit is met or exceeded • Any attempt to initiate a manual update • Result of the update attempt (success or failure) • The termination of a local/remote/interactive session by the session locking mechanism • Initiation/termination/failure of the SSH trusted channel to syslog server Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 72 of 89 • Initiation/termination/failure of the SSH trusted path with Admin • Initiation/termination/failure of an IPsec trusted channel, including Session Establishment with peer • Session establishment with CA • Application of firewall rules configured with the ‘log’ operation by the stateful traffic filtering function • Indication of packets dropped due to too much network traffic by the stateful traffic filtering function • Application of rules configured with the ‘log’ operation by the packet filtering function • Indication of packets dropped due to too much network traffic by the packet filtering function • Start-up and shut-down of the IPS functions • All dissimilar IPS events and reactions • Totals of similar events and reactions occurring within a specified time period • Modification of an IPS policy element • Modification of which IPS policies are active on a TOE interface • Enabling/disabling a TOE interface with IPS policies applied • Modification of which mode(s) is/are active on a TOE interface • Inspected traffic matches a list of known-good or known-bad addresses applied to an IPS policy • Inspected traffic matches a signature-based IPS policy with logging enabled • Inspected traffic matches an anomaly-based IPS policy 128. In addition the following management activities of TSF data are recorded: • configure the access banner; • configure the session inactivity time before session termination; • configure the authentication failure parameters for FIA_AFL.1; • Ability to configure audit behaviour; • configure the cryptographic functionality; • configure thresholds for SSH rekeying; • re-enable an Administrator account; • set the time which is used for time-stamps. 129. The detail of what events are to be recorded by syslog are determined by the logging level specified the “level” argument of the “set system syslog” CLI command. To ensure compliance with the requirements the audit knobs detailed in [ECG1] must be configured. 130. As a minimum, Junos OS records the following with each log entry: • date and time of the event and/or reaction • type of event and/or reaction Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 73 of 89 • subject identity (where applicable) • the outcome (success or failure) of the event (where applicable). 131. Because of the nature of IPS event logs, log generation often happens in bursts and can generate a large volume of messages during an attack. To manage the volume of log messages, Junos supports log suppression, which suppresses multiple instances of the same log occurring from the same or similar sessions over the same period of time. IPS log suppression is enabled by default and can be customized based on the following configurable attributes: • Source/destination addresses; • Number of log occurrences after which log suppression begins; • Maximum number of logs that log suppression can operate on; • Time after which suppressed logs are reported. 132. Suppressed logs are reported as single log entries containing the count of occurrences 133. In order to identify the key being operated on, the following details are recorded for all administrative actions relating to cryptographic keys (generating, importing, changing and deleting keys): • PKID – certificate id will be recorded when generating or deleting a key pair • IKE SPI – IP address of the initiator and responder recorded, together with the SPI, will be recorded when generating a key pair. The IP address of the initiator and responder will provide the unique link to the key identifier (SPI) of the key that has been destroyed in the session termination • SSH session keys– key reference provided by process id • SSH keys created for outbound trusted channel to external syslog server • SSH keys imported for outbound trusted channel to external syslog server • SSH key configured for SSH public key authentication –the hash of the public key that is to be used for authentication is recorded in syslog 134. For SSH (ephemeral) session keys the PID is used as the key reference to relate the key generation and key destruction audit events. The key destruction event is recorded as a session disconnect event. For example, key generation and key destruction events for a single SSH session key would be reflected by records similar to the following: Sep 27 15:09:36 yeti sshd[6529]: Accepted publickey for root from 10.163.18.165 port 45336 ssh2: RSA SHA256:l1vri77TPQ4VaupE2NMYiUXPnGkqBWIgD5vW0OuglGI … Sep 27 15:09:40 yeti sshd[6529]: Received disconnect from 10.163.18.165 port 45336:11: disconnected by user Sep 27 15:09:40 yeti sshd[6529]: Disconnected from 10.163.18.165 port 45336 135. SSH keys generated for outbound trusted channels are uniquely identified in the audit record by the public key filename and fingerprint. For example: Sep 27 23:36:49 yeti ssh-keygen [67873]: Generated SSH key file /root/.ssh/id_rsa.pub with fingerprint SHA256:g+7lsR7x4lQb1JT8Q3scfb2sOl8lyccojGdmkmw4dwM 136. SSH keys imported for use in establishing outbound trusted channels are uniquely identified in the audit record by the hash of the key imported and the username importing (to which the key will be bound). Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 74 of 89 137. It should be noted that SSH keys used for trusted channels are NOT deleted by mgd when SSH is de-configured. Hence, the only time SSH keys used for trusted channels are deleted is when a “request system zeroize” action is performed and the whole appliance is zeroized (which by definition cannot be recorded) 138. All events recorded by syslog are timestamped. The clock function of Junos OS provides a source of date and time information for the appliance, used in audit timestamps, which is maintained using the hardware Time Stamp Counter as the clock source. (FAU_GEN.2, FPT_STM_EXT.1) 139. Syslog can be configured to store the audit logs locally (FAU_STG_EXT.1), and optionally to send them to one or more syslog log servers via Netconf over SSH (FAU_STG.1, FMT_MOF.1/Functions). Local audit log are stored in /var/log/ in the underlying filesystem. Only a Security Administrator can read log files, or delete log and archive files through the CLI interface or through direct access to the filesystem having first authenticated as a Security Administrator. The syslogs are automatically deleted locally according to configurable limits on storage volume. The default maximum size is 1Gb. The default maximum size can be modified by the user, using the “size” argument for the “set system syslog” CLI command. 140. The Junos OS defines an active log file and a number of “archive” files (10 by default, but configurable from 1 to 1000). When the active log file reaches its maximum size, the logging utility closes the file, compresses it, and names the compressed archive file ‘logfile.0.gz’. The logging utility then opens and writes to a new active log file. When the new active log file reaches the configured maximum size, ‘logfile.0.gz’ is renamed ‘logfile.1.gz’, and the active log file is closed, compressed, and renamed ‘logfile.0.gz’. When the maximum number of archive files is reached and when the size of the active file reaches the configured maximum size, the contents of the oldest archived file are deleted so the current active file can be archived. 141. A 1Gb syslog file takes approximately 0.25Gb of storage when archived. Syslog files can acquire complete storage allocated to /var filesystem, which is platform specific. However, when the filesystem reaches 92% storage capacity an event is raised to the administrator but the eventd process (being a privileged process) still can continue using the reserved storage blocks. This allows the syslog to continue storing events while the administrator frees the storage. If the administrator does not free the storage in time and the /var filesystem storage becomes exhausted a final entry is recorded in the log reporting “No space left on device” and logging is terminated. The appliance continues to operate in the event of exhaustion of audit log storage space. 7.6 Management 142. Accounts assigned to the Security Administrator role are used to manage Junos OS in accordance with [NDcPP]. User accounts in the TOE have the following attributes: user identity (user name), authentication data (password) and role (privilege). The Security Administrator is associated with the defined login class “security-admin”, which has the necessary permission set to permit the administrator to perform all tasks necessary to manage Junos OS in accordance with the requirements of [NDcPP].(FMT_SMR.2) 143. The TOE provides user access either through the system console or remotely over the Trusted Path using the SSHv2 protocol. Users are required to provide unique identification and authentication data before any access to the system is granted, as detailed in Section 7.2 above. (FMT_SMR.2, FMT_SMF.1) 144. The Security Administrator has the capability to: • Administer the TOE locally via the serial ports on the physical device or remotely over an SSH connection. • Initiate a manual update of TOE firmware (FMT_MOF.1/ManualUpdate): Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 75 of 89 o Query currently executing version of TOE firmware (FPT_TUD_EXT.1) o Verify update using digital signature (FPT_TUD_EXT.1) • Manage Functions: o Transmission of audit data to an external IT entity, including Start/stop and modify the behaviour of the trusted communication channel to external syslog server (netconf over SSH) and the trusted path for remote Administrative sessions (SSH) (FMT_MOF.1/Functions, FMT_MOF.1/Services, FMT_SMF.1) o Handling of audit data, including setting limits of log file size (FMT_MOF.1/Functions) • Manage TSF data (FMT_MTD,1/CoreData) o Create, modify, delete administrator accounts, including configuration of authentication failure parameters o Reset administrator passwords o Re-enable an Administrator account (FIA_AFL.1); • Manage crypto keys (FMT_MTD.1/CryptoKeys): o SSH key generation (ecdsa, ssh-rsa) • Perform management functions (FMT_SMF.1): o Configure the access banner (FTA_TAB.1) o Configure the session inactivity time before session termination or locking, including termination of session when serial console cable is disconnected (FTA_SSL_EXT.1, FTA_SSL.3) o Ability to import X.509v3 certificates (FCS_IPSEC_EXT.1) o Manage cryptographic functionality (FCS_SSHS_EXT.1), including: ▪ ssh ciphers ▪ hostkey algorithm ▪ key exchange algorithm ▪ hashed message authentication code ▪ thresholds for SSH rekeying o Set the system time (FPT_STM_EXT.1) o Ability to configure Firewall rules (FFW_RUL_EXT.1); o Ability to configure the VPN-associated cryptographic functionality (FCS_COP.1/DataEncryption, FCS_CKM.1.1/IKE, FCS_IPSEC_EXT.1); o Ability to configure the IPsec functionality (FCS_IPSEC_EXT.1), including configuration of IKE lifetime-seconds (within range 180 to 8640044 , with default value of 180 seconds), IPsec lifetime-seconds (within range 180 to 86400, with default value of 28800 seconds45 ), and Lifetime-kilobytes (within range 64 to 4294967294 kilobytes) and ability to configure the reference identifier for the peer; 44 180 to 86400 seconds rang is a range of 3 minutes to 24 hours. 45 28800 seconds is 8 hours. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 76 of 89 o Ability to enable, disable, determine and modify behavior, and configure all other VPN-associated security functions of the TOE identified in [VPN_EP] (FPF_RUL_EXT.1, FCS_COP.1/DataEncryption, FCS_CKM.1.1/IKE, FCS_IPSEC_EXT.1); o Enable, disable signatures applied to sensor interfaces, and determine the behavior of IPS functionality (IPS_NTA_EXT.1, IPS_IPB_EXT.1, IPS_SBD_EXT.1, IPS_ABD_EXT.1) o Modify these parameters that define the network traffic to be collected and analysed (IPS_NTA_EXT.1): ▪ Source IP addresses (host address and network address); ▪ Destination IP addresses (host address and network address); ▪ Source port (TCP and UDP); ▪ Destination port (TCP and UDP); ▪ Protocol (IPv4 and IPv6) ▪ ICMP type and code o Update (import) IPS signatures (IPS_SBD_EXT.1); o Create custom IPS signatures (IPS_SBD_EXT.1); o Configure anomaly detection (IPS_ABD_EXT.1); o Enable and disable actions to be taken when signature or anomaly matches are detected (IPS_SBD_EXT.1); o Modify thresholds that trigger IPS reactions (IPS_ABD_EXT.1); o Modify the duration of traffic blocking actions (IPS_ABD_EXT.1); o Modify the known-good and known-bad lists (of IP addresses or address ranges) (IPS_IPB_EXT.1); o Configure the known-good and known-bad lists to override signature-based IPS policies (IPS_SBD_EXT.1). 145. Detailed topics on the secure management of Junos OS are discussed in [ECG1]. 7.7 User Data Protection 146. The only resource made available to information flowing through a TOE is the temporary storage of packet information when access is requested and when information is being routed. User data is not persistent when resources are released by one user/process and allocated to another user/process. Temporary storage (memory) used to build network packets is erased when the resource is called into use by the next user/process. Junos knows, and keeps track of, the length of the packet. This means that when memory allocated from a previous user/process arrives to build the next network packet, Junos is aware of when the end of the packet is reached and pads a short packet with zeros accordingly. Therefore, no residual information from packets in a previous information stream can traverse through the TOE. (FDP_RIP.2) 7.8 Packet Filtering/Stateful Traffic 147. The boot sequence of the TOE appliances also aids in establishing the securing domain and preventing tampering or bypass of security functionality. This includes ensuring the packet filtering rules cannot be bypassed during the boot sequence of the TOE. The following steps list the boot sequence for the TOE: • BIOS hardware and memory checks • Loading and initialization of the FreeBSD Kernel OS • FIPS self-tests and firmware integrity tests are executed • The init utility is started (mounts file systems, sets up network cards to communicate on the network, and generally starts all the processes that usually are run on a FreeBSD system at startup) Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 77 of 89 • Daemon programs such as Internet Service Daemon (INETD), Routing Protocol Daemon (RPD), Syslogd are started; Routing and forwarding tables are initialized • Management Daemon (or MGD) is loaded, allowing access to management interface • Physical interfaces are active 148. Once the interfaces are brought up, they will start to receive and send packets based on the current configuration (or not receive or send any packets if they have not been previously configured). Interfaces are brought up only after successful loading of kernel and Information Flow subsystems, and these interfaces cannot send or receive packets unless previously configured by an Administrator. Since the Management Daemon is not loaded until after the kernel and INETD are initialized, no modification to the security attributes can be made by a user or process other than via the management process. 149. The trusted and untrusted network connection interfaces on the security appliance are not enabled until all of the components on the appliance are fully initialized; power-up tests are successful and ready to enforce the configured security policies. In this manner, the TOE ensures that Administrators are appropriately authorized when they exercise management commands and any network traffic is always subject to the configured information flow policies. 150. The TOE is configured to associate network interfaces to IP subnets. Source IP addresses are then associated with the network interface. 151. Junos is composed of a number of separate executables, or daemons. If a failure occurs in the “flow” daemon (flowd) causing it to halt, no packet processing will occur and no packets will be forwarded. A failure in another daemon will not prevent the flow daemon from enforcing the policy rule set. 152. The Information Flow subsystem is responsible for processing the arriving packets from the network to the TOE's network interface. Based on Administrator-configured policy, interface and zone information, the packet flows through the various modules of the Information Flow subsystem. Rules within policies are processed in an Administrator-defined order when network traffic flows through the TOE network interfaces. By default, the TOE behavior is to deny packets when there is no rule match unless another required condition allows the network traffic If a security risk is found in the packet. e.g. denial-of-service attacks, the packet is dropped and an event is logged. The packet does not continue to the next module for processing. If the packet is not dropped by a given module, the interrupt handling routine calls the function for the next relevant module. In case of an interface getting overwhelmed, packets are dropped. This is recorded by the SNMP mibs as well as a log. When an interface gets overwhelmed with CPU utilization 99% then packets are dropped with syslog record as 'CPU Utilization greater than 99, expect packet loss'. 153. The Information Flow subsystem consists of the following modules: • IP Classification Module • Attack Detection Module • Session Lookup Module • Security Policy Module • Session Setup Module • Inetd Module • Rdp Module Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 78 of 89 154. The IP Classification module retrieves information from packets received on the network interface device, classifies packets into several categories, saves classification information in packet processing context, and provides other modules with that information for assisting further processing. 155. The Attack Detection module provides inline attack detection such as IP Spoofing for the security appliance. This module monitors arriving traffic, performs predefined attack detection services (prevents attacks), and issues actions when an attack is found. 156. The Session Lookup module performs lookups in the session table which is used for all interfaces based on the information in incoming packets. Specifically, the lookup is based on the exact match of source IP address and port, destination IP address and port, protocol attributes (e.g., SYN, ACK, RST, and FIN), and egress/ingress zone. The input is passed to the module as a set of parameters from the Attack Detection module via a function call. The module returns matching wing if a match is found and 0 otherwise. Sessions are removed when terminated. 157. The Session Setup module is only available for packets that do not match current established sessions. It is activated after the Session Lookup module. If packet has a matched session, it will skip the session setup module and proceed to the Security Policy module, and other modules. Eventually if the packet is not destined for the TOE, the Network interface will pass the traffic out of the appliance. 158. The Security Policy module examines traffic passing through the TOE (via Session Setup module) and determines if the traffic can pass based on administrator-configured access policies. The Security Policy module is the core of the firewall and IPS functionalities in the TOE: It is the policy enforcement engine that fulfills the security requirements for the user. The Security Policy module will deny packets when there is no policy match unless another policy allows the traffic. 159. The Session Setup module performs the auditing of denied packets. If there is a policy to specifically deny traffic, traffic matching this deny policy is dropped and logged in traffic log. If there is no policy to deny traffic, traffic that does not match any policy is dropped and not logged. In either case, Session Setup module does not create any sessions for denied traffic. Sessions are created for allowed traffic. 160. The INETD module provides internet services for the TOE. The module listens on designated ports used by internet services such as FTP. When a TCP or UDP packet arrives with a particular destination port number, INETD launches the appropriate server program (e.g., SSHD) to handle the connection. 161. The RPD (Routing Protocol Daemon) module provides the implementations and algorithms for the routing protocols and route calculations. The primary goal of the RPD is to create and maintain the Routing Information Base (RIB), which is a database of routing entries. Each routing entry consists of a destination address and some form of next hop information. RPD module maintains the internal routing table and properly distributes routes from the routing table to Kernel subsystem used for traffic forwarding at the Network interface. 162. The TOE performs stateful network traffic filtering on network packets using the following network traffic protocols and network fields conforming to the described RFCs: PROTOCOL/RFC FIELDS Internet Control Message Protocol version 4 (ICMPv4) RFC 792 (ICMPv4) Type Code Internet Control Message Protocol version 6 (ICMPv6) RFC 4443 (ICMPv6) Type Code Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 79 of 89 PROTOCOL/RFC FIELDS Internet Protocol (IPv4) RFC 791 (IPv4) Source address Destination Address Transport Layer Protocol Internet Protocol version 6 (IPv6) RFC 2460 (IPv6) Source address Destination Address Transport Layer Protocol Transmission Control Protocol (TCP) RFC 793 (TCP) Source port Destination port User Datagram Protocol (UDP) RFC 768 (UDP) Source port Destination port Table 11 Traffic Filtering RFCs 163. Conformance to these RFCs is demonstrated by protocol compliance testing by the product QA team. 164. The TOE shall allow permit, deny, and log operations to be associated with rules and these rules can be assigned to distinct network interfaces. 165. The TOE accepts network packets if it matches an established TCP, UDP or ICMP session using: • TCP: source and destination addresses, source and destination ports, sequence number, flags • UDP: source and destination addresses, source and destination ports • ICMP: source and destination addresses, type, code 166. The TOE will remove existing traffic flows due to session inactivity timeout, or completion of the session. 167. The TOE supports FTP (RFC 959) to dynamically establish sessions allowing network traffic according to Administrator rules. Session events will be logged in accordance with ‘log’ operations defined in the rules. Source and destination addresses, source and destination ports, transport layer protocol, and TOE Interface are recorded in each log record. (FFW_RUL_EXT.2) 168. Junos implements what is referred to as an Application Layer gateway (ALG) that inspects FTP traffic to determine the port number used for data sessions. The ALG permits data traffic for the duration of the session, closing the port when the session ends. In this context, “session” refers to the TCP data transfer connection, not the duration of the FTP control session. Junos implements ALGs for a number of protocols. 169. The TOE enforces the following default reject rules with logging on all network traffic: • invalid fragments; • fragmented IP packets which cannot be re-assembled completely; • where the source address is equal to the address of the network interface where the network packet was received; • where the source address does not belong to the networks associated with the network interface where the network packet was received; • where the source address is defined as being on a broadcast network; • where the source address is defined as being on a multicast network; Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 80 of 89 • where the source address is defined as being a loopback address; • where the source address is a multicast; • packets where the source or destination address is a link-local address; • where the source or destination address is defined as being an address “reserved for future use” as specified in RFC 5735 for IPv4; • where the source or destination address is defined as an “unspecified address” or an address “reserved for future definition and use” as specified in RFC 3513 for IPv6; • with the IP options: Loose Source Routing, Strict Source Routing, or Record Route specified; • packets are checked for validity. “Invalid fragments” are those that violate these rules: o No overlap o The total fragments in one packet should not be more than 62 pieces o The total length of merged fragments should not larger than 64k o All fragments in one packet should arrive in 2 seconds o The total queued fragments has limitation, depending on the platform o The total number of concurrent fragment processing for different packet has limitations depending on platform 170. The TOE can be configured to drop connection attempts after a defined number of half-open TCP connections using the Junos screen ‘tcp syn-flood’, which provides both source and destination thresholds on the number of uncompleted TCP connections, as well as a timeout period. The source threshold option allows administrators to specify the number of SYN segments received per second from a single source IP address—regardless of the destination IP address—before Junos OS begins dropping connection requests from that source. Similarly, the destination threshold option allows administrators to specify the number of SYN segments received per second for a single destination IP address before Junos OS begins dropping connection requests to that destination. The timeout option allows administrators to set the maximum length of time before an uncompleted connection is dropped from the queue. 171. For more information about configuring event logging, see Junos OS Complete Software Guide for SRX Series Services Gateways (Volume 2), Guide 4: ‘Building Blocks Feature Guide for Security Devices’ and [ECG1] (FFW_RUL_EXT.1, FPF_RUL_EXT.1) 7.9 Intrusion Prevention System 172. The Junos OS Intrusion Detection and Prevention (IDP) policy enables selectively enforcing various attack detection and prevention techniques on network traffic passing through an IDP- enabled device. Policy rules can be defined to match a section of traffic based on a zone, network, and application, and then take active or passive preventive actions on that traffic. 173. An IDP policy is made up of rule bases, and each rule base contains a set of rules that specify rule parameters, such as traffic match conditions, action, and logging requirements. IDP policies can then be associated to firewall policies. IDP can be invoked on a firewall rule by rule basis for maximum granularity. Only firewall policies marked for IDP will be processed by IDP engine, all other rules will only be processed by the firewall46 . 46 Note that some of the security functionality required by the IPS EP is implemented at the firewall level without intervention of Junos IDP engine. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 81 of 89 174. Firewall Policies match Source Zone, Destination Zone, Source IP, Destination IP, Source Port, Destination Port, and Protocol. Interface and VLAN matching can be achieved through the use of zones. Rules are organized into a firewall policy rulebase. Within IPS Policies, further matching for specific attacks is done on Source Zone, Destination Zone, Source IP, Destination IP, Source Port, Destination Port, and Protocol. Interface matching can be achieved through the use of zones. Attack Actions are configurable on a rule by rule basis. Rules within policies are processed in an Administrator-defined order when network traffic flows through the TOE network interfaces. (IPS_NTA_EXT.1.1) 175. Once stateful firewall processing of packets has been performed by the Information Flow subsystem, if a firewall policy that has been marked for IDP processing is triggered, the packets are processed by the IPS subsystem as follows: • Fragmentation Processing – IP Fragments are reordered and reassembled. Duplicate, over/undersized, overlapping, incomplete and other invalid fragments are discarded. • Flow Module SSL Decryption – sessions are checked for existing IP Actions, if none exist, new sessions are created. If a destination is marked for SSL decryption, a copy of the SSL traffic will be sent to the decryption engine. The original packet will be queue until inspection is complete. • Packet Serialization and TCP Reassembly – packets are ordered and all TCP packets are reassembled into complete application messages. • Application ID – pattern matching is performed on the traffic to determine what application the traffic is. The traffic is still inspected for Attacks, even if application cannot be determined. • Protocol Decoding – protocol parsing and decoding is performed. Messages are deconstructed into application “contexts” which identify components of messages. Protocol Anomaly Detection is performed, along with AppDoS (if configured) by thresholds of these contexts. • Attack Signature Matching – signatures are detected via deterministic finite automaton (DFA) pattern matching. • IDP Attack Actions – when an attack is detected the corresponding policy configured action is executed. Possible actions include: o No Action o Drop packet o Drop connection o Close client (send an RST packet to the client) o Close server (sends an RST packet to the server) o Close client and server (sends an RST packet to both client and server) 176. The TOE supports stateful signature based attack detection defined as Attack Objects. Attack Objects use context based matching to match regular expressions in specific locations where they occur. Attack Objects can be composed of multiple signatures and protocol anomalies, including logical expressions between signatures for compound matching. 177. As indicated in Section 7.8 the TOE is capable of inspecting IPv4, IPv6, ICMPv4, TCP and UPD traffic. Conformance to these RFCs is demonstrated by protocol compliance testing by the product QA team. (IPS_NTA_EXT.1.2) Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 82 of 89 178. The TOE is capable of inspecting all traffic passing through the TOE’s Ethernet interfaces (inline mode). Ethernet interfaces can be assigned to Zones on which firewall and IDP policies are predicated. The TOE supports management through the console port, as well as through a dedicated Ethernet management port whose traffic is never processed for routing. Remote management of the TOE can also be performed via SSH as described in Section 7.1.3. (IPS_NTA_EXT.1.3) 179. The TOE supports the definition of known-good and known-bad lists of source and/or destination addresses at the firewall rule level as described in Section 7.8. Address ranges can be defined by creating address book entries and attaching them to firewall policies. (IPS_IPB_EXT.1) 180. IPS signatures (in the sense of the IPS EP) are articulated at different points along the traffic processing flow implemented in the TOE. In Junos OS, interfaces are grouped into zones. The TOE supports the definition of signatures at the zone level, also known as the screen level. Junos OS screen options secure a zone by inspecting, then allowing or denying, all connection attempts that require crossing an interface bound to that zone. Sanity checks on IPv4 and IPv6 aimed at detecting malformed packets are performed at the screen level. In addition to attack detection and prevention at the screen level, Junos OS implements firewall and IDP policies at the inter-, intra-, and super-zone policy levels (super-zone here means in global policies, where no security zones are referenced). The TOE supports inspection of the following packet header information: • IPv4: Version; Header Length; Packet Length; ID; IP Flags; Fragment Offset; Time to Live (TTL); Protocol; Header Checksum; Source Address; Destination Address; and IP Options. • IPv6: Version; traffic class; flow label; payload length; next header; hop limit; source address; destination address; routing header; home address options. • ICMP: Type; Code; Header Checksum; and Rest of Header (varies based on the ICMP type and code). • ICMPv6: Type; Code; and Header Checksum. • TCP: Source port; destination port; sequence number; acknowledgement number; offset; reserved; TCP flags; window; checksum; urgent pointer; and TCP options. • UDP: Source port; destination port; length; and UDP checksum. 181. Signatures can be defined to match the any of above header-field values, using the command “set security idp custom-attack”, along with the actions (allow/block), using the command “set security idp idp-policy”, that the TOE will perform when a match is found in the processed packets. The matching criteria can be "equal", "greater-than", "less-than" or "not-equal". (IPS_SBD_EXT.1.1) 182. The TOE also supports string-based pattern-matching inspection of packet payload data for the above listed protocols. For TCP payload inspection, Junos OS provides pre-defined attack signatures to detect FTP commands, HTTP commands and content, and STMP states. Alternative, administrators can define custom-attack signatures for these application layer protocols using the command “set security idp custom-attack”. (IPS_SBD_EXT.1.2) 183. The TOE is capable of detecting the following signatures using Junos predefined screen options: IPS EP signature name Junos screen name IP Fragments Overlap (Teardrop attack, Bonk attack, or Boink attack) ip tear-drop IP source address equal to the IP destination (Land attack) tcp land Fragmented ICMP Traffic (e.g. Nuke attack) icmp fragment Large ICMP Traffic (Ping of Death attack) icmp ping-death Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 83 of 89 IPS EP signature name Junos screen name TCP NULL flags tcp tcp-no-flag TCP SYN+FIN flags tcp syn-fin TCP FIN only flags tcp fin-no-ack UDP Bomb Attack udp length-error ICMP flooding (Smurf attack, and ping flood) icmp flood TCP flooding (e.g. SYN flood) tcp syn-flood IP protocol scanning ip unknown-protocol TCP port scanning tcp port-scan UDP port scanning udp port-scan ICMP scanning icmp ip-sweep Table 12 IPS signature names 184. The default action for the above screens is to drop the packets. To allow the packets through, the “alarm-without-drop” action can be defined using the command “set security screen ids- option”. 185. The TOE is also capable of detecting the following signatures: • TCP SYN+RST flags, by defining an custom attack to match “protocol tcp tcp-flags rst” and “protocol tcp tcp-flags syn”47 ; • UDP Chargen DoS attack , by configuring a firewall policy to match the predefined “junos-chargen” with the desired allow/block reaction; • Flooding of a network (DoS attack), by the configuration of policers that allow establishing prioritization and bandwidth limits for different type of network traffic. (IPS_SBD_EXT.1.3, IPS_SBD_EXT.1.4) 186. The TOE allows administrators to define signatures for anomalous traffic in terms of throughput (bits per second), time of the day for defined source/destination address and source/destination port, frequency of traffic patterns and thresholds of traffic patterns. 187. Anomaly signatures based on time of day characteristics are implemented by configuring schedulers using the Junos command ‘set schedulers’ and attaching them to firewall policies, which in turn specify the target traffic in terms of IP addresses and port numbers as well as the action to be perform on signature triggering (allow or block/drop traffic). 188. Anomaly signatures based on throughput characteristics are implemented by configuring policers with a bandwidth limit and the desired signature action (discard or forward), using the Junos command ‘set firewall policer’, and attaching it to any interface with the Junos command ‘set interfaces’. Traffic exceeding the specified throughput limit is dropped when the policer is configured to discard traffic. A policer can be applied to specific inbound or outbound IP packets in a Layer 3 traffic flow at a logical interface by using a stateless firewall filter. If an input firewall filter is configured on the same logical interface as a policer, the policer is executed first. If an output firewall filter is configured on the same logical interface as a policer, the firewall filter is executed first. (IPS_ABD_EXT.1) 189. For more information about configuring event logging, see the Junos OS Complete Software Guide for SRX Series Services Gateways (Volume 2), Part 9: ‘Intrusion Detection and Prevention Feature Guide for Security Devices’ and the Junos OS Common Criteria Evaluated Configuration Guide for SRX Series Security Devices. 190. (IPS_NTA_EXT.1, IPS_IPB_EXT.1, IPS_SBD_EXT.1, IPS_ABD_EXT.1) 47 By default the TOE will drop packets where the TCP flags SYN and ACK are set at the screen level. Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 84 of 89 8 Rationales 8.1 SFR dependency analysis The dependencies between SFRs implemented by the TOE are satisfied as demonstrated in [NDcPP] Appendix E.1. Security Functional Requirement Dependency Rationale FAU_GEN.1/ND FPT_STM.1 FPT_STM_EXT.1 included (which is hierarchic to FPT_STM.1) FAU_GEN.1/IPS FPT_STM.1 FPT_STM_EXT.1 included (which is hierarchic to FPT_STM.1) FAU_GEN.2 FAU_GEN.1 FIA_UID.1 FAU_GEN.1 Included Satisfied by FIA_UIA_EXT.1, which specifies the relevant Administrator identification timing FAU_STG_EXT.1 FAU_GEN.1 FTP_ITC.1 FAU_GEN.1 included FTP_ITC.1 included FAU_STG.1 FAU_GEN.1 FAU_GEN.1 Included FCS_CKM.1/ND FCS_CKM.2 or FCS_COP.1 FCS_CKM.4 FCS_CKM.2 included FCS_CKM.4 included FCS_CKM.1/IKE FCS_CKM.2 or FCS_COP.1 FCS_CKM.4 FCS_CKM.2 included FCS_CKM.4 included FCS_CKM.2 FTP_ITC.1 or FTP_ITC.2 or FCS_CKM.1 FCS_CKM.4 FCS_CKM.1 included (also FTP_ITC.1 as a secure channel that could be used for import) FCS_CKM.4 included FCS_CKM.4 FTP_ITC.1 or FTP_ITC.2 or FCS_CKM.1 FCS_CKM.1 included (also FTP_ITC.1 as a secure channel that could be used for import) FCS_COP.1/DataEncryption FTP_ITC.1 or FTP_ITC.2 or FCS_CKM.1 FCS_CKM.4 FCS_CKM.1 included (also FTP_ITC.1 as a secure channel that could be used for import) FCS_CKM.4 included FCS_COP.1/SigGen FTP_ITC.1 or FTP_ITC.2 or FCS_CKM.1 FCS_CKM.4 FCS_CKM.1 included (also FTP_ITC.1 as a secure channel that could be used for import) FCS_CKM.4 included FCS_COP.1/Hash FTP_ITC.1 or FTP_ITC.2 or FCS_CKM.1 FCS_CKM.4 FCS_CKM.1 included (also FTP_ITC.1 as a secure channel that could be used for import) FCS_CKM.4 included FCS_COP.1/KeyedHash FTP_ITC.1 or FTP_ITC.2 or FCS_CKM.1 FCS_CKM.4 FCS_CKM.1 included (also FTP_ITC.1 as a secure channel that could be used for import) FCS_CKM.4 included FCS_RBG_EXT.1 None n/a Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 85 of 89 Security Functional Requirement Dependency Rationale FCS_IPSEC_EXT.1 FCS_CKM.1 FCS_CKM.2 FCS_COP.1/DataEncryption FCS_COP.1/SigGen FCS_COP.1/Hash FCS_COP.1/KeyedHash FCS_RBG_EXT.1 FCS_CKM.1 included FCS_CKM.2 included FCS_COP.1/DataEncryption included FCS_COP.1/SigGen included FCS_COP.1/Hash included FCS_COP.1/KeyedHash included FCS_RBG_EXT.1 included FCS_SSHS_EXT.1 FCS_CKM.1 FCS_CKM.2 FCS_COP.1/DataEncryption FCS_COP.1/SigGen FCS_COP.1/Hash FCS_COP.1/KeyedHash FCS_RBG_EXT.1 FCS_CKM.1 included FCS_CKM.2 included FCS_COP.1/DataEncryption included FCS_COP.1/SigGen included FCS_COP.1/Hash included FCS_COP.1/KeyedHash included FCS_RBG_EXT.1 included FIA_AFL.1 FIA_UAU.1 Satisfied by FIA_UIA_EXT.1, which specifies the relevant Administrator authentication FIA_PMG_EXT.1 None n/a FIA_UIA_EXT.1 FTA_TAB.1 FTA_TAB.1 included FIA_UAU_EXT.2 None n/a FIA_UAU.7 FIA_UAU.1 Satisfied by FIA_UIA_EXT.1, which specifies the relevant Administrator authentication FIA_X509_EXT.1/Rev None n/a FIA_X509_EXT.2 None n/a FIA_X509_EXT.3 FCS_CKM.1 Cryptographic Key Generation FCS_CKM.1/ND included FIA_PSK_EXT.1 None n/a FMT_MOF.1/ManualUpdate FMT_SMR.1 FMT_SMF.1 FMT_SMR.2 included FMT_SMF.1 included FMT_MOF.1/Services FMT_SMR.1 FMT_SMF.1 FMT_SMR.2 included FMT_SMF.1 included FMT_MOF.1/Functions FMT_SMR.1 FMT_SMF.1 FMT_SMR.2 included FMT_SMF.1 included FMT_MTD.1/CoreData FMT_SMR.1 FMT_SMF.1 FMT_SMR.2 included FMT_SMF.1 included FMT_MTD.1/CryptoKeys FMT_SMR.1 FMT_SMF.1 FMT_SMR.2 included FMT_SMF.1 included FMT_SMF.1/ND None n/a FMT_SMF.1/IPS None n/a FMT_SMR.2 FIA_UID.1 Satisfied by FIA_UIA_EXT.1, which specifies the relevant Administrator authentication FPT_SKP_EXT.1 None n/a FPT_APW_EXT.1 None n/a FPT_TST_EXT.1 None n/a FPT_TST_EXT.3 None n/a FPT_TUD_EXT.1 FCS_COP.1/SigGen or FCS_COP.1/Hash FCS_COP.1/SigGen Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 86 of 89 Security Functional Requirement Dependency Rationale FPT_STM.EXT.1 None n/a FPT_FLS.1/SelfTest None n/a FTA_SSL_EXT.1 FIA_UID.1 Satisfied by FIA_UIA_EXT.1, which specifies the relevant Administrator authentication FTA_SSL.3 None n/a FTA_SSL.4 None n/a FTA_TAB.1 None n/a FTP_ITC.1 None n/a FTP_TRP.1/Admin None n/a FDP_RIP.2 None n/a FPF_RUL_EXT.1 None n/a FFW_RUL_EXT.1 None n/a FFW_RUL_EXT.2 None n/a IPS_NTA_EXT.1 None n/a IPS_IPB_EXT.1 None n/a IPS_SBD_EXT.1 None n/a IPS_ABD_EXT.1 None n/a Table 13 SFR Dependency Analysis Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 87 of 89 9 Glossary AES Advanced Encryption Standard ANSI American National Standards Institute API Application Program Interface BGP Border Gateway Protocol cPP collaborative Protection Profile CCM Counter with Cipher Block Chaining-Message Authentication Code CFP C Form-factor Pluggable CM Configuration Management CSP Critical security parameter DFA Deterministic Finite Automaton DES Data Encryption Standard DH Diffie Hellman EAL Evaluation Assurance Level ECC Elliptic Curve Cryptography ECDSA Elliptic Curve Digital Signature Algorithm EP Extended Package, defined in [CC1] ESP Encapsulating Security Payload FFC Finite Field Cryptography FIPS Federal Information Processing Standard FTP File Transfer Protocol FWEP Firewall Extended Package GPIM Gigabit-Backplane PIM HMAC Keyed-Hash Authentication Code I&A Identification and Authentication ICMP Internet Control Message Protocol ID Identification IDS Intrusion Detection System IETF Internet Engineering Task Force IKE Internet Key Exchange IOC I/O (Input/Output) Cards IP Internet Protocol IPS Intrusion Prevention System IPsec Internet Protocol Security IPsec ESP Internet Protocol Security Encapsulating Security Payload IPv6 Internet Protocol Version 6 IPX Internetwork Packet Exchange ISAKMP Internet Security Association and Key Management Protocol IS-IS Intermediate System-to-Intermediate System ISO International Organization for Standardization IT Information Technology JET Junos Extension toolkit. Control plane APIs for Junos. Junos Juniper Operating System LDP Label Distribution Protocol MAC Mandatory Access Control MIC Modular Interface Cards MPC Modular Port Concentrator MRE Medium Robustness Environment NAT Network Address Translation NDcPP Network Device collaborative Protection Profile Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 88 of 89 NTP Network Time Protocol OSI Open Systems Interconnect OSP Organizational Security Policy OSPF Open Shortest Path First PAM Pluggable Authentication Module PFE Packet Forwarding Engine PFEP Linux process that manages the PFE. Also referred to as forwarding daemon. PIC/PIM Physical Interface Card/Module PKI Public Key Infrastructure POE Power over Ethernet PP Protection Profile PRNG Pseudo Random Number Generator QSFP Quad SFP RE Routing Engine RFC Request for Comment RIP Routing Information Protocol RNG Random Number Generator RSA Rivest, Shamir, Adelman SA Security Association SCB Switch Control Board SCEP Simple Certificate Enrollment Protocol SFP Small Form-factor Pluggable SFR Security Functional Requirement SHA Secure Hash Algorithm SNMP Simple Network Management Protocol SPC Services Processing Card SPU Services Processing Units SSD Solid State Drive SSH Secure Shell SSL Secure Sockets Layer ST Security Target TCP/IP Transmissions Control Protocol/ Internet Protocol TOE Target of Evaluation TSF TOE Security Functionality TSFI TSF interfaces UDP User Datagram Protocol VPN Virtual Private Network VPNEP Virtual Private Network Extended Package VDSL Very-high-bit-rate Digital Subscriber Line XFP 10 Gigabit SFP Security Target Junos OS 19.2R1 for SRX300, SRX320, SRX340, SRX345, SRX345-DUAL-AC and SRX550M Series Juniper Networks Version 3.7 Page 89 of 89 10 TOE Network Interface Options 191. The interface options supported for each TOE series appliance are described in the following reference document: • SRX300 Series and SRX550 High Memory Gateway Interface Modules Reference 10.1 Mini PIMs 192. The following interface options are available for all TOE devices. Interface Model number Description SRX-MP-1SERIAL-R Serial Mini-PIM provides physical connection for serial setup SRX-MP-1T1E1-R T1/E1 Mini-PIM provides the physical connection to T1 or E1 network media types SRX-MP1VDSL2-R VDSL2 Mini-PIM is part of the xDSL family of modem technologies, which provide faster data transmission over a single flat untwisted or twisted pair of copper wires SRX-MP-LTE-AE (North America, EU) SRX-MP-LTE-AA (Asia, Australia) Mini-PIM providing wireless WAN support. The Mini-PIM contains an integrated modem and operates over 3G and 4G networks. The Mini-PIM supports up to two SIM cards and can be installed in any of the Mini-PIM slots on the services gateways 10.2 GPIM / XPIM 193. The following interface options are available only for SRX550M devices. Interface Model number Description SRX-GP-8SFP 8-Port Gigabit Ethernet SFP XPIM providing 8 triple-speed (10/100/1000 Mbps) Ethernet ports SRX-GP-16GE-POE 16-Port Gigabit Ethernet SFP XPIM (with POE) providing 16 triple-speed (10/100/1000 Mbps) Ethernet ports, double-high card with POE support