Security Target for KB100 SCR eSIG
Zertifizierung ID: BSI-DSZ-CC-1046
Document ID: ASE_KB100SCReSIG
Version: 1.10
Status: Final
Date: 16.02.2018
Prepared by: Jürgen Meier, Ales Diessner
Date/Signature: 16.02.2018
Checked by: Dr. Philipp Tomsich, Philipp Sehner
Date/Signature: 16.02.2018
Approved by: Jürgen Meier
Date/Signature: 16.02.2018
History
Date Version Description Autor
19.06.2014 1.00 Creation Jürgen Meier
Ales Diessner
27.07.2017 1.01 Added BSI certification ID Ales Diessner
16.02.2018 1.10 Minor changes after commenting by BSI Philipp Sehner
Ales Diessner
© Copyright -2018 – All rights reserved
The information, knowledge and presentations contained in this documentation are property of
Fujitsu. The documentation or information contained, knowledge and presentations must not be
made accessible to others, published or distributed in any other way, neither completely nor partly,
directly nor indirectly, without the permission in writing of Fujitsu.
Fujitsu Technology Solutions GmbH
Bürgermeister-Ulrich-Str. 100
86199 Augsburg
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 3 of 30
Table of Contents
1. ST-Introduction (ASE_INT) .......................................................................................................... 5
1.1 ST reference and TOE reference ........................................................................................... 5
1.2 TOE Overview.......................................................................................................................... 6
1.2.1 TOE major security features for operational use ............................................................... 6
1.2.2 TOE Type........................................................................................................................... 7
1.2.3 Required non-TOE hardware/software/firmware............................................................... 7
1.3 TOE Description ...................................................................................................................... 8
2. ASE_CCL Conformance Claim .................................................................................................... 9
2.1 Common Criteria Conformance Claim.................................................................................. 9
2.2 PP Claim................................................................................................................................. 10
2.3 Package Claim....................................................................................................................... 10
3. ASE_SPD – Security Problem Definition.................................................................................. 11
3.1 Assumptions ......................................................................................................................... 11
3.2 Assets..................................................................................................................................... 12
3.3 Subjects ................................................................................................................................. 12
3.4 Threats ................................................................................................................................... 12
3.5 Organizational Security Policy ............................................................................................ 13
4. ASE_OBJ.1 – Security Objectives............................................................................................. 14
4.1 Security Objectives for the TOE.......................................................................................... 14
4.2 Security Objectives for the Environment ........................................................................... 14
4.3 Security Objectives Rationale ............................................................................................. 15
4.3.1 Countering the threats ..................................................................................................... 15
4.3.2 Covering the assumptions ............................................................................................... 15
5. ASE_ECD – Extended Component Definition.......................................................................... 17
5.1 Definition of the Family FPT_EMS....................................................................................... 17
5.1.1 FPT_EMS TOE emanation .............................................................................................. 17
6. ASE_REQ – Security Requirements ......................................................................................... 18
6.1 Security Functional Requirements for the TOE................................................................. 18
6.1.1 User Data Protection (FDP)............................................................................................. 19
6.1.2 FIA Identification and Authentication ............................................................................... 20
6.1.3 FTA TOE access.............................................................................................................. 21
6.1.4 Protection of the TSF (FPT)............................................................................................. 21
6.2 Security Assurance Requirements for the TOE................................................................. 22
6.3 Security Requirements Rationale........................................................................................ 22
6.3.1 Security Functional Requirements Rationale .................................................................. 22
6.3.2 Dependency Rationale .................................................................................................... 23
6.3.3 Justification for missing dependencies ............................................................................ 23
6.3.4 Security Assurance Requirements Rationale .................................................................. 23
7. ASE_TSS – TOE Summary Specification ................................................................................. 25
7.1 TOE Security Functions ....................................................................................................... 25
7.2 TOE Security Measures (SM.1)............................................................................................ 26
8. Rationales.................................................................................................................................... 27
8.1 Rationale of the TOE summery specification .................................................................... 27
8.1.1 Security functions and security requirements.................................................................. 27
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 4 of 30
8.1.2 Security functional requirements and security measures................................................ 28
9. Annex ........................................................................................................................................... 29
9.1 Abbreviations ........................................................................................................................ 29
9.2 Bibliography .......................................................................................................................... 30
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 5 of 30
1. ST-Introduction (ASE_INT)
1.1 ST reference and TOE reference
Titel: Security Target for KB100 SCR eSIG
Document Version: 1.10
Date: 16.02.2018
Dok. ID ASE_KB100SCReSIG
File name: ASE_Fujitsu-KB100SCReSIG-V1.10.docx
Author(s): Dr. Philipp Tomsich, Philipp Sehner, Jürgen Meier, Ales Diessner
Zert. ID: BSI-DSZ-CC-1046
The security features outline the functional and organizational security requirements and procedures
for the TOE and its operational environment which meet the security objectives “Secure PIN Entry”.
The Target of Evaluation (TOE) is the smartcard keyboard of the KB100 SCR eSIG series with firmware
version 2.0.0 and the product index HOS: 01.
The target of evaluation is divided into the following product variants:
• S26381-K101-L420-*-1 HOS: 01
• S26381-K101-L120-*-1 HOS: 01
All product variants contain the same firmware to be evaluated.
Theobroma Systems Design and Consulting GmbH designed the firmware for the
S26381-K101-Lx xx-*-1 HOS:01 smartcard keyboard. The driver software is created by HID Global.
Cherry GmbH is the manufacturer, Fujitsu is the product owner and distributor of the TOE.
Figure 1: KB100 SCR eSIG
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 6 of 30
Part number overview
The Product name KB100 SCR eSIG covers the part numbers S26381-K101-Lx xx-*-1. Below is a
brief description of the part number.
The part number is printed at the bottom side of the TOE and is followed by the product index of the
TOE.
1 = Fujitsu Technology Solutions, reference code group for keyboards and chip card readers
2 = Product family (technology, housing form, interface)
chip card reader keyboard K101 = certified
3 = Housing color (1 = marble grey; 4 = black)
4 = Country variant (20 = D)
5 = Packaging (-*-1 = in PE-Bag)
6 = Hardware version number (overall version of hardware)
1.2 TOE Overview
1.2.1 TOE major security features for operational use
The TOE ensures the functionality for entering a PIN securely.
The keyboard can be used universally in any smartcard-based applications. Possible applications
include:
• Qualified digital signature
• Home banking (HBCI)
• Access control (PC login)
When using the TOE as part of a signature application component for “qualified electronic signature”,
the security functionality of the TOE always works effectively irrespective of the application program
running it. For secure PIN entry, only the relevant CT command according to [CCID] needs to be used.
The used smartcard must be [ISO 7816] and [EMV2000] compliant processor smartcard. For more
details about the supported interfaces and protocols of smartcards, see Chapter 1.3.
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 7 of 30
1.2.2 TOE Type
The TOE is the smartcard keyboard KB100 SCR eSIG with an integrated Class 2 card reader for use in
a non-public environment as defined for assumption AE.1 (Chap. 3.1).
The physical boundary of TOE is defined by:
- the hardware
- the keyboard’s sealed housing
- the USB interface
- the smartcard interface
- Secure PIN- Entry State LED
The logical boundary covers:
- the firmware of the µC
The Quick Start Guide [A26381-K101-Z310-1-8N19], the detailed Operating Instruction [A26381-K101-
Z320-1-8N19] and the Software Developer’s Guide [SWdevG] are supplied to the user in electronic
form.
These documents are available from the Fujitsu Support website. The integrity of the documents is
protected using SHA-256 checksum as stated hereinafter:
SHA-256 for the Quick Start Guide [A26381-K101-Z310-1-8N19]:
51746651DD6E1BD8DBC7E86B87996BDC5EE797FD53E8AEED53286CD9606F1201
SHA-256 for the Operating Instruction [A26381-K101-Z320-1-8N19]:
3D79754C06BB4C028EB6D7F4B06308773CE0126EC383BFB2534F29F4C82AE71F
SHA-256 for the Software Developers Guide [SWdevG]:
32F3717FA7C15F6D69BA8025E8B066840030563F401265C6652CE5E323B8C3AB
1.2.3 Required non-TOE hardware/software/firmware
The KB100 SCR eSIG smartcard keyboard has no functionality that works without connecting to a host
PC. The keyboard must be connected to a PC. A PC is required with a [USB] standard interface for this.
The driver and tools included in the scope of delivery are not part of the TOE.
The following operating systems are supported by the drivers. The operating systems listed are
exemplary and not necessarily complete, as fundamentally not required for the secure operation of the
TOE.
• Windows 7
• Windows 8 / 8.1
• Windows 10
• Linux
To use the TOE as a secure PIN entry device a corresponding application, e.g. home banking software,
is required which use the [CT-API]- or [PC/SC]- Interface of the operating system to set the TOE into
the secure PIN entry mode.
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 8 of 30
1.3 TOE Description
The TOE, the smartcard keyboard KB100 SCR eSIG, features a keyboard with an integrated Class 2
reader that is able to read processor smartcards in line with [ISO 7816] and [EMV 2000] via various
application interfaces ([CT-API], [PC/SC] etc.). The keyboard works with all smartcard data transfer
protocols according to [ISO 7816] (T=0, T=1). It also supports data transfer protocols for memory
smartcards (2-wire, 3-wire protocols).
The smartcard keyboard recognizes the commands for PIN entry transmitted by the host software and
inserts the alphanumeric characters (including small letters, capital letters, numbers and
special letters) entered as the PIN to the locations occupied by the command on the smartcard. In this
process, only the fact that one of the numerical or alphanumerical keys has been pressed is reported
to the host. This enables the host application to show the user that he has pressed a key and how
many of the PIN digits have been entered so far. The PIN itself never leaves the smartcard keyboard
in plain text.
Secure PIN entry mode is signaled to the user by a red LED. The LEDs for indicating the smartcard
status are routed up through a light guide to the casing surface.
The following table lists the functions and keys which can be used to processing or confirming a PIN
during the secure PIN entry mode.
Function Keypad Alphanumerical field
Key Detailed
description
Confirms entry [Enter] [OK] []
Cancel [+] [CANCEL] [ESC]
Undo [-] [] []
Table 1: Key configuration
Figure 2: Keys for processing or confirming a PIN
The described Secure PIN entry mode is realized by the implemented security function SF.1 secure PIN
entry, which is supported by the security function SF.2 memory reprocessing. This security function
ensures that the memory where the entered PIN is stored temporarily will be reprocessed immediately
after usage.
The smartcard keyboard can be used on all host systems that have a corresponding USB interface.
Power is supplied via the USB bus.
The CT-API and PC/SC application interfaces can be used for all types of smartcard and is provided by
the host-PC. All functionalities at the interfaces are mapped in accordance with the [CT-API] and
[PC/SC] specification.
The scope of delivery includes:
• Keyboard with attached USB cable
• Quick Start Guide [A26381-K101-Z310-1-8N19] with instructions for installation via Fujitsu
website
• Detailed Operating Instruction [A26381-K101-Z320-1-8N19] with instruction for secure use
of the product via Fujitsu website
• Software Developer’s Guide [SWdevG] via Fujitsu website
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 9 of 30
• Driver and software tools via Fujitsu website
Optionally, the software and user guidance [A26381-K101-Z310-1-8N19] and [A26381-K101-Z320-1-
8N19] provided via Fujitsu website can also be enclosed on CD with the delivery. But as described under
Chapter 1.2.2 “TOE Type” only the SHA-256 secured version distributed via Fujitsu website is valid
under Common Criteria aspects and part of the certification.
The interface between host and keyboard is based on the functional scope of the [CCID]. The USB
interface represents the physical and logical boundary between the TOE and the host system.
The primary aim is to use the smart card keyboard for “qualified digital signature” applications as a
secure PIN entry- device.
Since, as a Class 2 reader, the smartcard keyboard is also able to capture identification data (PIN) and
securely transmit this data to secure signature creation devices (signature smartcards) it can also be
used for applications conforming to the Regulation (EU) No. 910/2014 of the European Parliament and
the Council on electronic identification and trust services for electronic transactions [eIDAS].
Furthermore, it transmits the hash value from the application to the signature card and loops back the
signature from the card to the signature application.
The following list of supported instruction bytes for secure PIN entry are to be used by the applications
and to be supported by the smartcards according to specifications or declined when not supported with
an appropriate error message:
• VERIFY (ISO/IEC 7816-4): INS=0x20
• CHANGE REFERENCE DATA (ISO/IEC 7816-8): INS=0x24
• DISABLE VERIFICATION REQUIREMENT (ISO/IEC 7816-8): INS=0x26
• ENABLE VERIFICATION REQUIREMENT (ISO/IEC 7816-8): INS=0x28
• UNBLOCK APPLICATION (EMV 2000): INS=0x18
• RESET RETRY COUNTER (ISO/IEC 7816-8): INS=0x2C
The housing is sealed with tamper-proof security labels, which self-destruct if removed.
The arrangement of the seals and the TOE housing design makes unauthorized opening impossible
without breaking a seal.
This allows the user to check the integrity of the keyboard, which he is also prompted to do.
Security components and data lines are arranged inside the housing in such a way that it is not possible
to gain access through existing openings, e.g. the card slot.
Due to the fact, that the Common Criteria component ALC_DEL.1 is not part of the certification, the
security review ends with the packaging process at the production line. The delivery of the TOE to the
secure environment in which the TOE will be used must be negotiated individually with every single
customer. Direct delivery to the user or administrator is preferred.
2. ASE_CCL Conformance Claim
2.1 Common Criteria Conformance Claim
This Security Target and the TOE claim conformance to
- Common Criteria for Information Technology Security Evaluation, Part 1:
Introduction and General Model, CCMB-2012-09-001, Version 3.1, Revision 4, September
2012 [1]
- Common Criteria for Information Technology Security Evaluation, Part 2:
Security Functional Components; CCMB-2012-09-002, Version 3.1, Revision 4, September
2012 [2]
- Common Criteria for Information Technology Security Evaluation, Part 3:
Security Assurance Requirements; CCMB-2012-09-003, Version 3.1, Revision 4, September
2012 [3]
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 10 of 30
Conformance is claimed for Part 2 extended and Part 3 conformant.
2.2 PP Claim
This Security Target claims no Protection Profile.
2.3 Package Claim
The following components claimed for the TOE:
ASE_CCL.1, ASE_ECD.1, ASE_INT.1, ASE_OBJ.2, ASE_REQ.2, ASE_SPD.1, ASE_TSS.1,
ADV_ARC.1, ADV_FSP.4, ADV_IMP.1, ADV_TDS.3,
AGD_OPE.1, AGD_PRE.1,
ALC_CMC.3, ALC_CMS.3, ALC_DVS.1, ALC_LCD.1, ALC_TAT.1
ATE_COV.2, ATE_DPT.1, ATE_FUN.1, ATE_IND.2,
AVA_VAN.3
This component claim corresponds to the assurance level EAL 3 augmented by the components
ADV_FSP.4, ADV_IMP.1, ADV_TDS.3, ALC_TAT.1 and AVA.VAN.3 and reduced by the component
ALC_DEL.1.
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 11 of 30
3. ASE_SPD – Security Problem Definition
The following section features the security environment in which the TOE should be used. This covers
the security aspects of the environment and the anticipated use of the TOE.
In this context, the assets to be protected and the people involved are explained with respect to the
proper use and misuse of the TOE.
The PIN as the identification feature of the smartcard owner, as well as the firmware and hardware of
the TOE, must be protected.
Exposing the identification data and security related changes to the TOE are considered to be threats
to the TOE by an attacker.
To counteract these threats, mechanisms have been integrated:
• Secure PIN entry is shown by a LED
• Residual information protection by zeroization of memory areas containing sensitive data
• The TOE may only transmit the PIN to the smartcard
• The PIN may only be forwarded to the smartcard via the approved PIN commands
• The TOE is protected by the seal
• The end user is informed of his responsibility using the TOE as PIN entry device.
3.1 Assumptions
In general, it is assumed that the end user is informed about his responsibility while using the TOE.
The following assumptions show in detail the responsibilities of the user about a secure use of the
TOE.
Assumptions regarding the physical conditions
Assumptions Description
AE.1 It is assumed that the TOE is used as a smartcard keyboard for the non-public
environment only with single and multi-user PCs in the private domain and in the office
environment.
Any area which is not accessible for the general public is classed as a non-public
environment.
Such a non-public environment shall ensure that an attacker cannot install or use any
equipment to spy on the entered PIN by the use of audio or video recording equipment
or at least it enables the user to identify such equipment.
Visitors have only controlled access and visitor policies ensure that they don’t carry any
equipment for audio or video recording.
The access of service providers and external employees to the premises is
contractually regulated.
Assumptions regarding the personnel conditions
Assumptions Description
AE.2 It is assumed that the user is convinced of the integrity of the seal before using for the
first time, and periodically thereafter, by checking whether any security-related
changes to the seals or smartcard keyboard have been made.
AE.3 It is assumed that the user is advised on rules regarding secure storage and non-
disclosure of the PIN by the issuer of the smartcard.
This includes that the user ensures that the PIN is entered unobserved.
AE.4 It is assumed that the user checks the status of the LED to ensure that the secure PIN
entry mode is active, while entering the PIN using the number keypad.
Assumptions regarding the connection options or the connections to other IT systems or products
Assumptions Description
AE.5 It is assumed that only processor smartcards are used which satisfy the [ISO 7816]
and [EMV 2000] specifications. The user or organization which procures the
smartcards that will be used with the TOE, must ensure, that the smartcards fulfill the
proposed requirements.
Table 1: Assumptions
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 12 of 30
3.2 Assets
The following assets must be protected by the TOE and its environment.
Assets to be
protected
Description
PIN The PIN as identification code of the user represents a personal secret.
The user enters the PIN using the numerical and alphanumerical key area of the
TOE. This is then sent to the smartcard by the TOE.
The TOE must ensure the confidentiality of the PIN.
Table 2: Assets
3.3 Subjects
The following subjects are interacting with the TOE:
Subject Description
Attacker A human or a process acting on his behalf, located outside the TOE. The main
goal of the attacker is to gain the entered PIN.
The attacker could use the following weak points:
- the interface between the TOE and the host- PC,
- the electromagnetic emanation.
Attack attempts can be conducted from outside of the operational environment.
The attacker can also try to get physical access to the TOE within the given
access possibilities to the operational environment.
The attacker has an enhanced-basic attack potential.
User A user uses the TOE as a standard computer input device for normal office work
and also as security device where secure PIN entry is required for example as
part of a signature application component. The user is non-hostile and knows the
existing guidance documents of the TOE. The user is responsible for the secure
operation of the TOE.
Host-PC A host-PC can be any PC which supports USB devices. The TOE can be used
as input device with an integrated class 2 card reader with the host-PC. In
addition, the host-PC supports an application with the functionality of PIN
verification against a signature card where a class 2 card reader is supported for
secure PIN entry.
Smart Card The user is in possession of the smart card and the corresponding PIN used for
e.g. digital signature. The TOE is handling the communication of the smart card
in its card slots and an application on the host-PC.
Table 3: Subjects
3.4 Threats
In the following, all threats are considered which are directed against the assets which require specific
protection within the TOE or its environment and are relevant for the secure operation of the TOE. The
perpetrators of threats are identified and described in terms of attacks and compromised assets.
Threats Description
T.1 Spy on the PIN entered on the TOE via the interface the TOE is connected to the
host PC. The attack may be performed using a malicious application installed on the
host PC.
Adverse effects: The PIN information entered by the user may be compromised.
Threat agent: Attacker
Asset: PIN
T.2 Try to provoke PIN entry and obtain the PIN in this way.
Adverse effects: Obtaining the PIN by provoked PIN entry without active security
functions.
Threat agent: Attacker
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 13 of 30
Threats Description
Asset: PIN
T.3a Manipulation of the TOE into its components (hardware and firmware) or replacing
the TOE by a manipulated keyboard to determine the PIN.
Adverse effects: Obtaining the PIN by manipulation of the hardware or firmware of
the TOE to bypass the implemented security functions.
Threat agent: Attacker
Asset: PIN
T.3b Read out the PIN which is stored temporarily in the TOE.
Adverse effects: Read out the PIN over TOE interfaces or direct after internal
processing.
Threat agent: Attacker
Asset: PIN
T.4 Writing the PIN in an unprotected area of the smart card to then read it.
Adverse effects: Direct the PIN to unprotected areas of a smart card.
Threat agent: Attacker
Asset: PIN
T.5 Make security-related changes to the TOE by tampering with the security seal.
Adverse effects: Manipulation the TOE by tampering the security seals to obtain
the entered PIN.
Threat agent: Attacker
Asset: PIN
T.6 Eavesdropping of the electromagnetic emanation to draw conclusion about the
entered PIN by analyses of the recorded signals. The attacker and the attack
equipment is located outside the operational environmental of the TOE in an
adjacent area.
Adverse effects: Eavesdropping of the PIN with equipment to record
electromagnetic emanation for subsequent analysis in order to compromise PIN
information from adjacent areas.
Threat agent: Attacker
Asset: PIN
Table 4: Threats
3.5 Organizational Security Policy
No organizational security policy is defined.
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 14 of 30
4. ASE_OBJ.1 – Security Objectives
The security objectives for the TOE and its environment are defined in this chapter. The following
security objectives counteract all identified threats and outline the assumptions.
In chapter 4.1 the security objectives for the TOE are defined, while in chapter 4.2, the security objectives
for the environment of the TOE are specified.
Chapter 4.3 presents the correlations between the identified assumptions and threats and the defined
security objectives.
4.1 Security Objectives for the TOE
The security objectives for the TOE are listed in the following table.
Security objectives
for the TOE
Description
O.1 The TOE ensures that the PIN is not stored, except at the time of processing.
O.2 The TOE ensures that secure PIN entry mode is clearly signaled to the user.
O.3 The TOE ensures that the PIN is only transferred to the smartcard.
O.4 The TOE ensures that the PIN is passed on to the smartcard only by means of
PIN command with approved instruction bytes.
O.5 The TOE ensures that any security changes to the TOE are recognizable by
the security seal.
O.6 The TOE ensures that the electromagnetic emanation cannot be used to
simply draw conclusion about the entered PIN.
Table 5: Security objectives for the TOE
4.2 Security Objectives for the Environment
The user is advised on rules regarding secure storage and non-disclosure of the PIN by the issuer of
the smart card.
The end user must be informed of his responsibility while using the TOE.
The security objectives for the environment are defined in the following table.
Security objectives
for the environment
Description
OE.1 The TOE must be used as a smartcard keyboard for the non-public
environment. This comprises that the user is obligated to check the operational
environment regularly about installed audio and video recording equipment used
for spy attacks on the PIN.
It must be ensured that visitors, service providers or external employees cannot
install or carry any kind of audio or video recording equipment.
OE.2 The user must check the integrity of the security seal (seal number) and the
TOE regularly before using the device.
OE.3 The user must follow the instructions of the card issuer regarding the secure
handling of the card and the PIN and ensure that the PIN is entered unobserved.
OE.4 While entering the PIN, the user must check the status of the LED to ensure that
the secure PIN entry mode is active.
OE.5 The user may only use processor cards which satisfy the [ISO 7816] and [EMV
2000] specifications.
Table 6: Security objectives for the environment
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 15 of 30
4.3 Security Objectives Rationale
The following table provides an overview for the security objectives coverage. The following chapters
provide a more detailed explanation of this mapping:
O.1 O.2 O.3 O.4 O.5 O.6 OE.1 OE.2 OE.3 OE.4 OE.5
T.1 X
T.2 X X
T.3a X X
T.3b X
T.4 X
T.5 X
T.6 X
AE.1 X
AE.2 X
AE.3 X
AE.4 X
AE.5 X
Table 7: Security objectives coverage
4.3.1 Countering the threats
The threat T.1 describes that an attacker may try to eavesdrop and log the communication between
the TOE and the host system by a malicious tool installed on the host system, to obtain an entered
PIN or bypass the security functions. This treat is countered by the objective O.3 which describes that
the PIN will never leave the TOE other than to the corresponding smartcard.
The threat T.2, which describes that an attacker can provoke the PIN entry by a program from outside
of the TOE is countered by the objective O.2 and OE.4. O.2 describes that the TOE will signal the
secure PIN entry mode clearly to the user and OE.4 ensures that the user check the status of the
secure PIN entry LED while he is entering the PIN to be sure that the secure PIN entry mode is active.
Threat T.3a which describes the manipulation of the TOE into its components (hardware and firmware)
to bypass the security functions is countered by the objective O.5 which ensures that manipulation of
the TOE is recognizable because of the use of security seals.
It is also assumed, that an attacker can replace the TOE by a manipulated keyboard. The Objective
OE.2 counteracts to this threat, which is an assumption to the operational environment that the serial
numbers of the security seals will be checked regularly by the user.
Objective O.1 which ensures that the PIN will never be stored in the TOE, except during the
processing counters the threat T.3b which describes the reading of the PIN after PIN entry from
memories.
The threat T.4, which describes that an attacker could try to redirect the PIN to an unprotected area of
a smart card, is covered by the objective O.4. This objective ensures that the TOE only accepts PIN
commands with permitted instruction bytes.
The threat T.5, which describes that an attacker could tamper with the security seal to manipulate the
TOE is countered by the objective O.5 which claims that manipulations of the TOE are recognizable
because of the use of security seals.
The threat T.6, which describes that an attacker can eavesdrop the PIN by analyzing the
electromagnetic emanation is countered by the security objective O.6 which claims that the
electromagnetic emanation cannot be exploited by a simply way.
4.3.2 Covering the assumptions
AE.1 It is assumed that the TOE is used as a smartcard keyboard for the non-public environment.
OE.1 The TOE must be used as a smartcard keyboard for the non-public environment.
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 16 of 30
AE.2 It is assumed that the user is convinced of the integrity of the seal before using for the first time,
and periodically thereafter, by checking whether any security-related changes to the smartcard
keyboard have been made.
OE.2 establish an objective which covers the assumption directly
AE.3 It is assumed that the user follows the instructions of the card issuer regarding the secure
handling of the card and the PIN. Thus, it is also assumed that the user ensures that the PIN is
entered unobserved.
OE.3 establish an objective which covers the assumption directly
AE.4 It is assumed that the user checks the status of the LED to ensure that the secure PIN entry
mode is active, while entering the PIN.
OE.4 establish an objective which covers the assumption directly
AE.5 It is assumed that only processor smartcards are used which satisfy the [ISO 7816] and [EMV
2000] specifications.
OE.5 establish an objective which covers the assumption directly
Table 8: Covering the assumptions
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 17 of 30
5. ASE_ECD – Extended Component Definition
This Security Target uses components defined as extensions to CC part 2.
The defined components are drawn from extended component definition [PP_0068].
5.1 Definition of the Family FPT_EMS
The family FPT_EMS (TOE Emanation) of the class FPT (Protection of the TSF) is defined here to
describe the IT security functional requirements of the TOE. The TOE shall prevent attacks against
secret data processed by the TOE where the attack is based on external observable physical
phenomena of the TOE. Examples of such attacks are evaluation of TOE’s electromagnetic radiation,
timing attacks, etc. This family describes the functional requirements for the limitation of intelligible
emanations being not directly addressed by any other component of CC part 2 [CC2].
The family ‘TOE Emanation (FPT_EMS)’ is specified as follows:
5.1.1 FPT_EMS TOE emanation
This family defines requirements to mitigate intelligible emanations.
Component levelling:
FPT_EMS.1 TOE emanation has one constituent:
FPT_EMS.1.1 Limit of Emissions requires to not emit intelligible emissions enabling access to TSF
data or user data.
Management: FPT_EMS.1
There are no management activities foreseen.
Audit: FPT_EMS.1
There are no actions defined to be auditable.
FPT_EMS.1 TOE Emanation
FPT_EMS.1.1 The TOE shall not emit [assignment: types of emissions] in excess of [assignment:
specified limits] enabling access to [assignment: list of types of TSF data] and [assignment: list of
types of user data].
Hierarchical to: No other components
Dependencies: No dependencies
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 18 of 30
6. ASE_REQ – Security Requirements
This Chapter defines the functional requirements and the security assurance requirements for the TOE
and its environment.
Operations for assignment, selection, refinement and iteration have been made.
All operations which have been performed from the original text of [CC2] are written in italics for
assignments, underlined for selections and bold text for refinements. Furthermore the [brackets]
from [CC2] are kept in the text
6.1 Security Functional Requirements for the TOE
The TOE has to satisfy the SFRs delineated in the following table. The 4th row of the table designates
the dependencies of the SFRs.
Nr. Component Description Dependencies
FDP User Data Protection
1 FDP_ACC.1 Subset access control FDP_ACF.1
2 FDP_ACF.1 Security attribute based access control FDP_ACC.1
FMT_MSA.3
3 FDP_RIP.1 Subset residual information protection none
FIA Identification and authentication
4 FIA_UAU.7 Protected authentication feedback FIA_UAU.1
FTA TOE access
5 FTA_TAB.1 Default TOE access banners none
FPT Protection of the TSF
6 FPT_EMS.1 TOE Emanation none
7 FPT_PHP.1 Passive detection of physical attack none
Table 9: Security functional requirement for the TOE
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 19 of 30
6.1.1 User Data Protection (FDP)
6.1.1.1 FDP_ACC.1 Subset access control
FDP_ACC.1.1 The TSF shall enforce the [Smart card reader access control policy] on
[
Subjects:
• User via key matrix interface
• Host- PC via USB interface
• Smart card via smart card interface
Objects:
• PIN
• Secure PIN entry mode LED
Operations among subjects and objects covered by the SFP:
• Entry of the PIN
• Transfer of the PIN
• Control of the secure PIN entry LED
].
Hierarchical to: No other components.
Dependencies: FDP_ACF.1 Security attribute based access control
6.1.1.2 FDP_ACF.1 Security attribute based access control
FDP_ACF.1.1 The TSF shall enforce the [smartcard reader access control policy] to objects
based on the following:
[
list of subjects:
• User via the key matrix interface
• Host- PC via USB interface
• Smart Card via smart card reader interface
attribute: [none]
objects:
• PIN
• Secure PIN entry mode LED
Attribute: State of the Secure PIN entry mode LED
].
FDP_ACF.1.2 The TSF shall enforce the following rules to determine if an operation among
controlled subjects and controlled objects is allowed:
[
▪ The Host- PC (subject) sends via the USB- Interface an explicit command
from an application to the smart card interface, whereby the secure PIN
entry LED (object) will be triggered (operation) by the TOE. The entered
PIN (object) will be send (operation) to the corresponding smart card, if the
command structure of the command meets [CCID] and the instruction
correlates with one of the following instruction bytes:
• VERIFY (ISO/IEC 7816-4) INS= 0x20
• CHANGE REFERENCE DATA (ISO/IEC 7816-8) INS=0x24
• DISABLE VERIFICATION REQUIREMENT (ISO/IEC 7816-8) INS=0x26
• ENABLE VERIFICATION REQUIREMENT (ISO/IEC 7816-8) INS=0x28
• RESET RETRY COUNTER (ISO/IEC 7816-8) INS=0x2C
• UNBLOCK APPLICATION (EMV 2000): INS=0x18
▪ The user (subject) can only enter (operation) the PIN (object) via defined
keys of the alphanumeric key area and the numeric pad of the keyboard.
▪ The TOE sends (operation) the PIN (object) to the smart card (subject) in
the smart card interface only.
].
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 20 of 30
FDP_ACF.1.3 The TSF shall explicitly authorize access of subjects to objects based on the
following additional rules:
[No further rules required for the TSF].
FDP_ACF.1.4 The TSF shall explicitly deny access of subjects to objects based on the
following additional rules:
[No further rules required for the TSF].
Hierarchical to: No other components.
Dependencies: FDP_ACC.1 Subset access control
FMT_MSA.3 Static attribute initialization
6.1.1.3 FDP_RIP.1 Subset residual information protection
FDP_RIP.1.1 The TSF shall ensure that any previous information content of a resource is
made unavailable upon the [deallocation of the resource from] the following
objects:
[
- PIN
- Secure PIN entry mode LED
].
Application Note 1: After activation, the forwarding of a PIN command, withdrawal of the
smartcard or cancellation, the PIN memory area is zeroized to ensure that
no personal identification data or data fragments remain in the smartcard
keyboard.
FDP_RIP1.1 for the PIN LED means that the defined switch off the PIN
LED is ensured.
Hierarchical to: No other components.
Dependencies: No dependencies.
6.1.2 FIA Identification and Authentication
6.1.2.1 FIA_UAU.7 Protected authentication feedback
FIA_UAU.7.1 The TSF shall provide only [non-PIN placeholder character] to the user while
the authentication is in progress.
Hierarchical to: No other components.
Dependencies: FIA_UAU.1 Timing of authentication
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 21 of 30
6.1.3 FTA TOE access
6.1.3.1 FTA_TAB.1 Default TOE access banners
FTA_TAB.1.1 Before establishing a user session, the TSF shall indicate, whether the TOE
is in a secure state or not.
Application Note 2: The state of secure PIN entry mode will be indicated by a red LED.
Hierarchical to: No other components.
Dependencies: No dependencies.
6.1.4 Protection of the TSF (FPT)
6.1.4.1 FPT_EMS.1 TOE Emanation
FPT_EMS.1.1 The TOE shall not emit [information about the timing of the matrix scan during
secure PIN entry] in excess of [non-useful information] enabling access to [none] and [PIN].
Application Note 3: The key matrix scan during the secure PIN entry mode must be
scrambled. Therefore, a random number generator must be used to
scramble the scan randomly.
The random number as seed for the random number generator must be
loaded into the TOE securely.
It must be ensured during the preparative installation procedure of the TOE
at production site that a random number from sufficient quality is been
used. Evidences have been taken within the scope of the ALC evaluation.
6.1.4.2 FPT_PHP.1 Passive detection of physical attack
FPT_PHP.1.1 The TSF shall provide unambiguous detection of physical tampering that
might compromise the TSF.
Application Note 4: Based on authentic and tamper-proof security seals affixed over the join
between the bottom and top parts of the housing is it possible to reliably
establish that the hardware has not been tampered with.
FPT_PHP.1.2 The TSF shall provide the capability to determine whether physical tampering
with the TSF's devices or TSF's elements has occurred.
Application Note 5: This can be ensured because the housing cannot be opened without
breaking the seal.
The nature (destruction characteristics) of the seal ensures that it cannot
be removed and re-attached without damaging it.
Hierarchical to: No other components.
Dependencies: No dependencies.
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 22 of 30
6.2 Security Assurance Requirements for the TOE
The TOE fulfills the below listed Security Assurance Requirements which represents EAL 3
augmented by the components marked in bold text and reduced by the component ALC_DEL.1. The
complete text for these requirements can be found in Part 3 of the Common Criteria [CC3].
Assurance Class Assurance Components
ADV: Development ADV_ARC.1: Security architecture description
ADV_FSP.4 Complete functional specification
ADV_IMP.1 Implementation representation of the TSF
ADV_TDS.3 Basic modular design
AGD: Guidance documents AGD_OPE.1 Operational user guidance
AGD_PRE.1 Preparative procedure
ALC: Life-cycle support ALC_CMC.3 Authorisation control
ALC_CMS.3 Implementation representation CM coverage
ALC_DVS.1 Identification of security measures
ALC_LCD.1 Developer defined life-cycle model
ALC_TAT.1 Well-defined development tools
ASE_CCL.1 Conformance claims
ASE: Security Target
evaluation
ASE_ECD.1 Extended components definition
ASE_INT.1 ST Introduction
ASE_OBJ.2 Security objectives
ASE_REQ.2 Derived security requirements
ASE_SPD.1 Security problem definition
ASE_TSS.1 TOE summary specification
ATE_COV.2 Analysis of coverage
ATE: Tests ATE_DPT.1 Testing: basic design
ATE_FUN.1 Functional testing
ATE_IND.2 Independent testing – sample
AVA: Vulnerability
assessment
AVA_VAN.3 Vulnerability analysis
Table 10: Chosen Evaluation Assurance Requirements
6.3 Security Requirements Rationale
6.3.1 Security Functional Requirements Rationale
The following table provides an overview for security functional requirements coverage.
O.1 O.2 O.3 O.4 O.5 O.6
FDP_ACC.1 X X
FDP_ACF.1 X X
FDP_RIP.1 X
FIA_UAU.7 X
FTA_TAB.1 X
FPT_EMS.1 X
FPT_PHP.1 X
Table 11: Security Functional Requirements Rationale
The security objective O.1 which ensures that the PIN is not stored, expect at the time of processing is
met by FDP_RIP.1 which defines that the PIN have to be securely deleted when it is no longer used.
Security objective O.2 which requires that the secure PIN entry mode is clearly signaled to the user is
directly and completely met by FTA_TAB.1 as this SFR requires that the TOE shall be able to indicate,
whether it is working in a secure state.
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 23 of 30
The security objective O.3 which requires that the PIN will be only transferred to the smartcard is met
by FDP_ACC.1, FDP_ACF.1 and FIA_UAU.7.
FDP_ACC.1 and FDP_ACF.1 define that nobody is able to read out the PIN from the keyboard.
FIA_UAU.7 supports this objective by providing only asterisk to the application during the user enters
a PIN.
FDP_ACC.1 and FCP_ACF.1 fulfills also the security objective O.4 which requires the use of approved
instruction bytes for PIN processing.
The security objective O.5 which ensures that any security changes are recognizable is met by
FPT_PHP.1 as this SFR requires that the TOE detected physical tampering.
The security objective O.6 which ensures that the PIN cannot be observed by simply analyses of the
electromagnetic emanation is met by FPT_EMS.1 which defines the TOE doesn’t emit timing
information during the secure PIN entry mode.
6.3.2 Dependency Rationale
SFR Dependencies Support of the dependencies
FDP_ACC.1 FDP_ACF.1 fulfilled
FDP_ACF.1 FDP_ACC.1; FMT_MSA.3 Fulfilled by FDP_ACC.1. See
chapter 6.3.3 for FMT_MSA.3
FDP_RIP.1 none -
FIA_UAU.7 FIA_UAU.1 See chapter 6.3.3
FTA_TAB.1 none -
FPT_EMS.1 none -
FPT_PHP.1 none -
Table 12: Dependencies of the SFR for the TOE
6.3.3 Justification for missing dependencies
The dependency FMT_MSA.3 of FDP_ACF.1 is considered to be not applicable as changes of
security attributes is not possible, whereby the management of security attributes is not applicable.
The dependency FIA_UAU.1 of FIA_UAU.7 is considered to be not applicable because user
authentication is no objective for the TOE. Therefore, no TSF mediated actions need to be defined as
executable without user authentication.
6.3.4 Security Assurance Requirements Rationale
The TOE fulfils the security assurance requirements, as claimed in chapter 2.3.
The following components corresponds to the Evaluation Assurance Level EAL 3 without the
component ALC_DEL.1
• ASE_CCL.1, ASE_ECD.1, ASE_INT.1, ASE_OBJ.2, ASE_REQ.2, ASE_SPD.1, ASE_TSS.1,
• AGD_OPE.1, AGD_PRE.1,
• ADV_ARC.1, ADV_FSP.3, ADV_TDS.2
• ALC_CMC.3, ALC_CMS.3, ALC_DVS.1, ALC_LCD.1
• ASE_OBJ.2, ASE_REQ.2
• ATE_COV.2, ATE_DPT.1, ATE_FUN.1, ATE_IND.2
• AVA_VAN.2
This assurance level has been augmented by the component:
• AVA_VAN.3
This component has the following direct and indirect dependencies, which has to be satisfied within
the evaluation:
• ADV_FSP.4
• ADV_TDS.3
• ADV_IMP.1
• ALC_TAT.1 (required by ADV_IMP.1)
The main decision about the Evaluation Assurance Level has been taken based on the fact that the
TOE described in this Security Target shall serve as a secure PIN entry device and based on the fact
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 24 of 30
that the TOE is used in a non-public environment but also needs to provide an adequate level of
protection for its assets.
The component ALC_DEL.1 has not been chosen to give the customer the decision about the security
measures for the delivery of the TOE to the operational environment.
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 25 of 30
7. ASE_TSS – TOE Summary Specification
This chapter describes the TOE summery specification under chapter 7.1 as well as the TOE security
measures under chapter 7.2. All assurance measures will be described under chapter 7.3
7.1 TOE Security Functions
To sign an electronic document digitally, the user is prompted by the application to insert his signature
card. The “digital signature” application must then be activated in the smartcard. To do this, the owner
must authenticate possession (signature card) and knowledge (PIN) using his signature card.
The priority here is to protect the personal identification data (PIN).
The TOE provides the user with the security features to protect the identification data (PIN) and to
reprocess information carriers (storage areas and LED display).
The implementation of the individual security functions is described below.
Security function 1: Secure PIN entry (SF.1)
The smartcard keyboard is switched to the secure PIN entry mode using an explicit CT
command according to [CCID]. This CT command contains the PIN handling agreements and
the smartcard command, in which the PIN is integrated at the specified location.
The instruction byte of the smartcard command is used to verify whether this is a PIN command
that explicitly expects a PIN to be entered. The table below shows the permitted instruction
bytes.
INS-
Byte:
Bezeichnung: Bedeutung Norm:
0x20 VERIFY PIN entry ISO/IEC
7816-4
0x24 CHANGE
REFERENCE DATA
Change PIN ISO/IEC
7816-8
0x26 DISABLE
VERIFICATION
REQUIREMENT
Activate PIN
ISO/IEC
7816-8
0x28 ENABLE
VERIFICATION
REQUIREMENT
Deactivate PIN
ISO/IEC
7816-8
0x18 UNBLOCK
APPLICATION
Unblock
Application
EMV 2000
0x2C RESET RETRY
COUNTER
Unlock PIN ISO/IEC
7816-8
Table 13: Instructionbytes [ISO 7816]/[EMV 2000]
After changing to the secure PIN entry mode, the key matrix query of the key area switches
from a serial scan into a random scan of the single columns of the key matrix.
The entered personal identification data is buffered in the internal RAM of the TOE, so that it
can be sent with the PIN command to the smartcard as soon as the entry is complete. PIN entry
mode is indicated visually by a red PIN LED until the PIN has been completely entered or the
operation is cancelled. The operation is cancelled by withdrawing the card, pressing the Cancel
key or exceeding the permitted input time.
The user is shown the progress of the entry, with a non-PIN placeholder character appearing for
each alphanumeric character entered. The dummy codes are output via the USB interface, and
are then displayed by the corresponding PC application. The process inside the TOE, however,
uses the correct PIN.
In the context of the SPD as described in Chapter 3, an attacker with enhanced-basic attack
potential cannot manipulate the security features, as the transfer of the PIN is only carried out
between the smart card and the TOE on the card reader interface. This is located inside the
TOE and is protected against tampering with the security seal.
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 26 of 30
Security function 2: Memory reprocessing (SF.2)
Communication between the PC system and smartcard is based on the so-called APDUs
according to [CCID]. If an APDU is received in the smartcard keyboard via the USB port, it is
stored temporarily and then sent to the smartcard. After activation, the forwarding of a PIN
command, withdrawal of the smartcard or cancellation, the PIN memory area is reprocessed to
ensure that no personal identification data or data fragments remain in the smartcard keyboard.
The memory area contains both the PIN and the APDU. Furthermore, the LED for indicating
secure PIN entry goes out.
In the context of the SPD as described in Chapter 3, an attacker with enhanced-basic attack
potential cannot circumvent this security function, as it is not possible to tamper with the
memory reprocessing in the TOE.
7.2 TOE Security Measures (SM.1)
Four authentic and tamper-proof security seals affixed over the join between the bottom and top parts
of the housing make it possible to reliably establish that the hardware has not been tampered with.
This can be ensured because the housing cannot be opened without breaking the seal.
The nature (destruction characteristics) of the seal ensures that it cannot be removed and re-affixed
without damaging it.
A 7-digit serial number on the seal permits it to be uniquely identified.
The seal employed satisfies the requirements of security level 2 as defined by [AIS 48].
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 27 of 30
8. Rationales
8.1 Rationale of the TOE summery specification
8.1.1 Security functions and security requirements
Security
function
SFR Comment
SF.1 Secure PIN entry FDP_ACC.1
FDP_ACF.1
FPT_EMS.1
FTA_TAB.1
FIA_UAU.7
The smartcard keyboard is switched to the secure PIN entry
mode using an explicit CT command according to [CCID].
This CT command contains the PIN handling agreements
and the smartcard command, in which the PIN is integrated
at the specified location. The instruction byte of the
smartcard command is used to verify whether this is a PIN
command that explicitly expects a PIN to be entered. The
table [Table 15] below shows the permitted instruction bytes.
The entered personal identification data is buffered in the
RAM, so that it can be sent with the PIN command to the
smartcard as soon as the entry is complete.
After changing to the secure PIN entry mode, the key matrix
query of the key area switches from a serial scan into a
random scan of the single columns of the key matrix.
PIN entry mode is indicated visually by a red PIN LED until
the PIN has been completely entered or the operation is
cancelled. The operation is cancelled by withdrawing the
card, pressing the Cancel key or exceeding the permitted
input time.
The user is shown the progress of the entry, with a non-PIN
placeholder character appearing for each alphanumeric
character entered. The dummy codes are output via the
USB interface, and are then displayed by the corresponding
PC application. The process inside the TOE, however, uses
the correct PIN.
SF.2 Memory
reproceccing
FDP_RIP.1 After activation, the forwarding of a PIN command,
withdrawal of the smartcard or cancellation, the PIN memory
area is reprocessed to ensure that no personal identification
data or data fragments remain in the smartcard keyboard.
Table 14: security functions and security requirements
INS-
Byte:
Designation meaning Norm:
20h VERIFY PIN entry ISO/IEC 7816-4
24h CHANGE REFERENCE
DATA
Change PIN ISO/IEC 7816-8
26h DISABLE VERIFICATION
REQUIREMENT
Activate PIN ISO/IEC 7816-8
28h ENABLE VERIFICATION
REQUIREMENT
Deactivate PIN ISO/IEC 7816-8
2Ch RESET RETRY
COUNTER
Unlock PIN ISO/IEC 7816-8
18h UNBLOCK APPLICATION Unblock Application EMV2000
Table 15: Instruction bytes
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 28 of 30
Security functional
requirements
SF.1 SF.2
FDP_ACC.1 x
FDP_ACF.1 x
FDP_RIP.1 x
FIA_UID.7 x
FTA_TAB.1 x
FPT_EMS.1 x
Table 16: Security Functional Requirement – Security Functions
8.1.2 Security functional requirements and security measures
Security
Measure
SFR Comment
SM.1 Sealing FPT_PHP.1 The SFR passive detection of physical attacks is not met
by a security function (SF) as an integrated part of the
TSF, but is met by the security measure (SM) sealing.
Table 17: Security functional requirements and security measures
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 29 of 30
9. Annex
9.1 Abbreviations
AP Advanced Performance
APDU Application Programming Data Unit
AIS Anwendungshinweise und Interpretationen zum Schema
BSI Bundesamt für Sicherheit in der Informationstechnik
CC Common Criteria,
CT Card Terminal
DIN Deutsches Institut für Normung e.V.
DRNG Deterministic Random Number Generator
EAL Evaluation Assurance Level
eIDAS Regulation for electronic identification and trust services for electronic transaction
EMV Europay International, Mastercard, Visa
HBCI Home Banking Computer Interface
ICC Integrated Chip Card
ISO International Organization for Standardization
IT Information Technology
PC Personal Computer
PC/SC Personal Computer/Smart Card
PIN Personal Identification Number
PP Protection Profile
RAM Random Access Memory
SF Security function
SM Security measure
ST Security Target
TOE Target of Evaluation
TSF TOE Security Functions
US United States
USB Universal Serial Bus
M Maßnahme
KB100 SCR eSIG Security Target for KB100 SCR eSIG Version 1.10, Final
Fujitsu
16.02.2018 ASE_Fujitsu-KB100SCReSIG-V1.10.docx Page 30 of 30
9.2 Bibliography
[AIS 48] Anwendungshinweise und Interpretationen zum Schema (AIS), AIS 48, Version 1,
Stand: 30.04.2015
[CC1] Common Criteria for Information Technology Security Evaluation, Part 1:
Introduction and General Model, Version 3.1, Revision 4, September 2012
[CC2] Common Criteria for Information Technology Security Evaluation, Part 2: Security
Functional Requirements, Version 3.1, Revision 4, September 2012
[CC3] Common Criteria for Information Technology Security Evaluation, Part 3: Security
Assurance Requirements, Version 3.1, Revision 4, September 2014
[CCID] Device Class Specification for USB Chip/Smart Card Interface Devices, Revision
1.00, March 20, 2001
[CT-API] Anwendungsunabhängiges CardTerminal Application Programming Interface für
Chipkartenanwendungen CT-API Version 1.1.1 / Juni 2001
[eIDAS] Verordnung (EU) Nr. 910/2014 des Europäischen Parlaments und des Rates vom
23. Juli 2014 über elektronische Identifizierung und Vertrauensdienste für
elektronische Transaktionen im Binnenmarkt und zur Aufhebung der Richtlinie
1999/93/EG
[EMV 2000] EMV 2000 Book 1 - Application independent ICC to Terminal Interface
requirements, Version 4.0, December 2000
[ISO 7816] DIN ISO 7816 - 1 Identification cards - Integrated circuit(s) cards with contacts –
Physical Characteristics
DIN ISO 7816 - 2 Identification cards - Integrated circuit(s) cards with contacts -
Dimensions and locations of the contacts
DIN ISO 7816 - 3 Identification cards - Integrated circuit(s) cards with contacts -
electrical characteristics and transmission protocols
DIN ISO 7816 - 4 Information technology - Identification cards - Integrated circuit(s)
cards with contacts - Inter - industry commands for interchange
DIN ISO 7816 – 8 Identification cards – Integrated circuit(s) cards with contacts –
Security related interindustry commands
[PP_0068] Machine Readable Travel Document using Standard Inspection Procedure with
PACE (PACE PP), BSI-CC-PP-0068-V2-2011-MA-01; Version 1.01, July the 22nd
2014
[PC/SC] Interoperability Specification for ICCs and Personal Computer Systems, PC/SC
Workgroup, Version 2.0, November 1999
[USB] Universal Serial Bus Specification; Revision 2.0, April 27th, 2000
[A26381-K101-
Z310-1-8N19]
Quick Start Guide Fujitsu KB100 SCR eSIG; A26381-K101-Z310-1-8N19;
Nov 2017; FTS_TastaturKB100SCReSIGBedienungsanleitung_122017_1192422
[A26381-K101-
Z320-1-8N19]
Operating Instruction Fujitsu KB100 SCR eSIG; A26381-K101-Z320-1-8N19;
Nov 2017; FTS_TastaturKB100SCReSIGBetriebsanleitung_122017_1192423
[SWdevG] Software Developers Guide Fujitsu KB100 SCR eSIG, Sept 2017;
FTS_TastaturKB100SCReSIGSWdevelopersguide_092017_1192511