BSI-DSZ-CC-1046-2018
for
KB100 SCR eSIG, S26381-K101-Lx 20-*-1, FW-
Version 2.0.0, HW-Version HOS: 01
from
Fujitsu Technology Solutions GmbH
BSI - Bundesamt für Sicherheit in der Informationstechnik, Postfach 20 03 63, D-53133 Bonn
Phone +49 (0)228 99 9582-0, Fax +49 (0)228 9582-5477, Infoline +49 (0)228 99 9582-111
Certification Report V1.0 CC-Zert-327 V5.2
BSI-DSZ-CC-1046-2018 (*)
Digital signature: Smart Card Readers
KB100 SCR eSIG
S26381-K101-Lx 20-*-1, FW-Version 2.0.0, HW-Version HOS: 01
from Fujitsu Technology Solutions GmbH
PP Conformance: None
Functionality: Product specific Security Target
Common Criteria Part 2 extended
Assurance: Common Criteria Part 3 conformant
ASE_CCL.1, ASE_ECD.1, ASE_INT.1, ASE_OBJ.2, ASE_REQ.2,
ASE_SPD.1, ASE_TSS.1, AGD_OPE.1, AGD_PRE.1, ADV_ARC.1,
ADV_FSP.4, ADV_IMP.1, ADV_TDS.3, ALC_CMC.3, ALC_CMS.3,
ALC_DVS.1, ALC_LCD.1, ALC_TAT.1, ATE_COV.2, ATE_DPT.1,
ATE_FUN.1, ATE_IND.2, AVA_VAN.3
The IT Product identified in this certificate has been evaluated at an approved evaluation
facility using the Common Methodology for IT Security Evaluation (CEM), Version 3.1
extended by Scheme Interpretations for conformance to the Common Criteria for IT
Security Evaluation (CC), Version 3.1. CC and CEM are also published as ISO/IEC 15408
and ISO/IEC 18045.
(*) This certificate applies only to the specific version and release of the product in its
evaluated configuration and in conjunction with the complete Certification Report and
Notification. For details on the validity see Certification Report part A chapter 4
The evaluation has been conducted in accordance with the provisions of the certification
scheme of the German Federal Office for Information Security (BSI) and the conclusions
of the evaluation facility in the evaluation technical report are consistent with the
evidence adduced.
This certificate is not an endorsement of the IT Product by the Federal Office for
Information Security or any other organisation that recognises or gives effect to this
certificate, and no warranty of the IT Product by the Federal Office for Information
Security or any other organisation that recognises or gives effect to this certificate, is
either expressed or implied.
Bonn, 6 April 2018
For the Federal Office for Information Security
Bernd Kowalski L.S.
Head of Division
SOGIS
Recognition Agreement
Common Criteria
Recognition Arrangement
recognition for components
up to EAL 2
Bundesamt für Sicherheit in der Informationstechnik
Godesberger Allee 185-189 - D-53175 Bonn - Postfach 20 03 63 - D-53133 Bonn
Phone +49 (0)228 99 9582-0 - Fax +49 (0)228 9582-5477 - Infoline +49 (0)228 99 9582-111
Certification Report BSI-DSZ-CC-1046-2018
This page is intentionally left blank.
4 / 26
BSI-DSZ-CC-1046-2018 Certification Report
Contents
A. Certification.......................................................................................................................7
1. Preliminary Remarks.....................................................................................................7
2. Specifications of the Certification Procedure................................................................7
3. Recognition Agreements...............................................................................................8
4. Performance of Evaluation and Certification.................................................................9
5. Validity of the Certification Result..................................................................................9
6. Publication...................................................................................................................10
B. Certification Results........................................................................................................11
1. Executive Summary....................................................................................................12
2. Identification of the TOE..............................................................................................13
3. Security Policy.............................................................................................................14
4. Assumptions and Clarification of Scope......................................................................14
5. Architectural Information..............................................................................................14
6. Documentation............................................................................................................16
7. IT Product Testing........................................................................................................16
8. Evaluated Configuration..............................................................................................18
9. Results of the Evaluation.............................................................................................18
10. Obligations and Notes for the Usage of the TOE......................................................19
11. Security Target...........................................................................................................20
12. Definitions..................................................................................................................20
13. Bibliography...............................................................................................................21
C. Excerpts from the Criteria...............................................................................................23
D. Annexes..........................................................................................................................25
5 / 26
Certification Report BSI-DSZ-CC-1046-2018
This page is intentionally left blank.
6 / 26
BSI-DSZ-CC-1046-2018 Certification Report
A. Certification
1. Preliminary Remarks
Under the BSIG1 Act, the Federal Office for Information Security (BSI) has the task of
issuing certificates for information technology products.
Certification of a product is carried out on the instigation of the vendor or a distributor,
hereinafter called the sponsor.
A part of the procedure is the technical examination (evaluation) of the product according
to the security criteria published by the BSI or generally recognised security criteria.
The evaluation is normally carried out by an evaluation facility recognised by the BSI or by
BSI itself.
The result of the certification procedure is the present Certification Report. This report
contains among others the certificate (summarised assessment) and the detailed
Certification Results.
The Certification Results contain the technical description of the security functionality of
the certified product, the details of the evaluation (strength and weaknesses) and
instructions for the user.
2. Specifications of the Certification Procedure
The certification body conducts the procedure according to the criteria laid down in the
following:
● Act on the Federal Office for Information Security1
● BSI Certification and Approval Ordinance2
● BSI Schedule of Costs3
● Special decrees issued by the Bundesministerium des Innern (Federal Ministry of the
Interior)
● DIN EN ISO/IEC 17065 standard
● BSI certification: Scheme documentation describing the certification process (CC-
Produkte) [3]
● BSI certification: Scheme documentation on requirements for the Evaluation Facility, its
approval and licencing process (CC-Stellen) [3]
● Common Criteria for IT Security Evaluation (CC), Version 3.14
[1] also published as
ISO/IEC 15408.
1
Act on the Federal Office for Information Security (BSI-Gesetz - BSIG) of 14 August 2009,
Bundesgesetzblatt I p. 2821
2
Ordinance on the Procedure for Issuance of Security Certificates and approval by the Federal Office for
Information Security (BSI-Zertifizierungs- und -Anerkennungsverordnung - BSIZertV) of 17 December
2014, Bundesgesetzblatt 2014, part I, no. 61, p. 2231
3
Schedule of Cost for Official Procedures of the Bundesamt für Sicherheit in der Informationstechnik
(BSI-Kostenverordnung, BSI-KostV) of 03 March 2005, Bundesgesetzblatt I p. 519
7 / 26
Certification Report BSI-DSZ-CC-1046-2018
● Common Methodology for IT Security Evaluation (CEM), Version 3.1 [2] also published
as ISO/IEC 18045.
● BSI certification: Application Notes and Interpretation of the Scheme (AIS) [4]
3. Recognition Agreements
In order to avoid multiple certification of the same product in different countries a mutual
recognition of IT security certificates - as far as such certificates are based on ITSEC or
CC - under certain conditions was agreed.
3.1. European Recognition of CC – Certificates (SOGIS-MRA)
The SOGIS-Mutual Recognition Agreement (SOGIS-MRA) Version 3 became effective in
April 2010. It defines the recognition of certificates for IT-Products at a basic recognition
level and, in addition, at higher recognition levels for IT-Products related to certain SOGIS
Technical Domains only.
The basic recognition level includes Common Criteria (CC) Evaluation Assurance Levels
EAL 1 to EAL 4. For "Smartcards and similar devices" a SOGIS Technical Domain is in
place. For "HW Devices with Security Boxes" a SOGIS Technical Domains is in place, too.
In addition, certificates issued for Protection Profiles based on Common Criteria are part of
the recognition agreement.
The current list of signatory nations and approved certification schemes, details on
recognition, and the history of the agreement can be seen on the website at
https://www.sogisportal.eu.
The SOGIS-MRA logo printed on the certificate indicates that it is recognised under the
terms of this agreement by the related bodies of the signatory nations. A disclaimer
beneath the logo indicates the specific scope of recognition.
This certificate is recognized under SOGIS-MRA for all assurance components selected.
3.2. International Recognition of CC – Certificates (CCRA)
The international arrangement on the mutual recognition of certificates based on the CC
(Common Criteria Recognition Arrangement, CCRA-2014) has been ratified on 08
September 2014. It covers CC certificates based on collaborative Protection Profiles (cPP)
(exact use), CC certificates based on assurance components up to and including EAL 2 or
the assurance family Flaw Remediation (ALC_FLR) and CC certificates for Protection
Profiles and for collaborative Protection Profiles (cPP).
The current list of signatory nations and approved certification schemes can be seen on
the website: http://www.commoncriteriaportal.org.
The Common Criteria Recognition Arrangement logo printed on the certificate indicates
that this certification is recognised under the terms of this agreement by the related bodies
of the signatory nations. A disclaimer beneath the logo indicates the specific scope of
recognition.
This certificate is recognized according to the rules of CCRA-2014, i. e. up to and including
CC part 3 EAL 2+ ALC_FLR components.
4
Proclamation of the Bundesministerium des Innern of 12 February 2007 in the Bundesanzeiger dated
23 February 2007, p. 3730
8 / 26
BSI-DSZ-CC-1046-2018 Certification Report
4. Performance of Evaluation and Certification
The certification body monitors each individual evaluation to ensure a uniform procedure, a
uniform interpretation of the criteria and uniform ratings.
The product KB100 SCR eSIG, S26381-K101-Lx 20-*-1, FW-Version 2.0.0, HW-Version
HOS: 01 has undergone the certification procedure at BSI.
The evaluation of the product KB100 SCR eSIG, S26381-K101-Lx 20-*-1, FW-Version
2.0.0, HW-Version HOS: 01 was conducted by SRC Security Research & Consulting
GmbH. The evaluation was completed on 22 March 2018. SRC Security Research &
Consulting GmbH is an evaluation facility (ITSEF)5
recognised by the certification body of
BSI.
For this certification procedure the sponsor and applicant is: Fujitsu Technology Solutions
GmbH.
The product was developed by: Fujitsu Technology Solutions GmbH.
The certification is concluded with the comparability check and the production of this
Certification Report. This work was completed by the BSI.
5. Validity of the Certification Result
This Certification Report applies only to the version of the product as indicated. The
confirmed assurance package is valid on the condition that
● all stipulations regarding generation, configuration and operation, as given in the
following report, are observed,
● the product is operated in the environment described, as specified in the following report
and in the Security Target.
For the meaning of the assurance components and assurance levels please refer to CC
itself. Detailed references are listed in part C of this report.
The Certificate issued confirms the assurance of the product claimed in the Security Target
at the date of certification. As attack methods evolve over time, the resistance of the
certified version of the product against new attack methods needs to be re-assessed.
Therefore, the sponsor should apply for the certified product being monitored within the
assurance continuity program of the BSI Certification Scheme (e.g. by a re-assessment or
re-certification). Specifically, if results of the certification are used in subsequent evaluation
and certification procedures, in a system integration process or if a user's risk
management needs regularly updated results, it is recommended to perform a re-
assessment on a regular e.g. annual basis.
In order to avoid an indefinite usage of the certificate when evolved attack methods would
require a re-assessment of the products resistance to state of the art attack methods, the
maximum validity of the certificate has been limited. The certificate issued on 6 April 2018
is valid until 5 April 2023. Validity can be re-newed by re-certification.
The owner of the certificate is obliged:
1. when advertising the certificate or the fact of the product's certification, to refer to
the Certification Report as well as to provide the Certification Report, the Security
5
Information Technology Security Evaluation Facility
9 / 26
Certification Report BSI-DSZ-CC-1046-2018
Target and user guidance documentation mentioned herein to any customer of the
product for the application and usage of the certified product,
2. to inform the Certification Body at BSI immediately about vulnerabilities of the
product that have been identified by the developer or any third party after issuance
of the certificate,
3. to inform the Certification Body at BSI immediately in the case that security relevant
changes in the evaluated life cycle, e.g. related to development and production sites
or processes, occur, or the confidentiality of documentation and information related
to the Target of Evaluation (TOE) or resulting from the evaluation and certification
procedure where the certification of the product has assumed this confidentiality
being maintained, is not given any longer. In particular, prior to the dissemination of
confidential documentation and information related to the TOE or resulting from the
evaluation and certification procedure that do not belong to the deliverables
according to the Certification Report part B, or for those where no dissemination
rules have been agreed on, to third parties, the Certification Body at BSI has to be
informed.
In case of changes to the certified version of the product, the validity can be extended to
the new versions and releases, provided the sponsor applies for assurance continuity (i.e.
re-certification or maintenance) of the modified product, in accordance with the procedural
requirements, and the evaluation does not reveal any security deficiencies.
6. Publication
The product KB100 SCR eSIG, S26381-K101-Lx 20-*-1, FW-Version 2.0.0, HW-Version
HOS: 01 has been included in the BSI list of certified products, which is published regularly
(see also Internet: https://www.bsi.bund.de and [5]). Further information can be obtained
from BSI-Infoline +49 228 9582-111.
Further copies of this Certification Report can be requested from the developer6
of the
product. The Certification Report may also be obtained in electronic form at the internet
address stated above.
6
Fujitsu Technology Solutions GmbH
Buergermeister-Ulrich-Straße 100
86199 Augsburg
10 / 26
BSI-DSZ-CC-1046-2018 Certification Report
B. Certification Results
The following results represent a summary of
● the Security Target of the sponsor for the Target of Evaluation,
● the relevant evaluation results from the evaluation facility, and
● complementary notes and stipulations of the certification body.
11 / 26
Certification Report BSI-DSZ-CC-1046-2018
1. Executive Summary
The Target of Evaluation (TOE) is the product “KB100 SCR eSIG, S26381-K101-Lx 20-*-1,
FW-Version 2.0.0, HW-Version HOS: 01", produced by Fujitsu Technology Solutions
GmbH. The TOE is a computer keyboard with an integrated smart card reader that
conforms to the USB classes "Human Interface Device" (HID) and "Smart Card" (CCID).
The keyboard is intended for use in a non-public environment.
The Security Target [6] is the basis for this certification. It is not based on a certified
Protection Profile.
The TOE Security Assurance Requirements (SAR) are based entirely on the assurance
components defined in Part 3 of the Common Criteria (see part C or [1], Part 3 for details).
The TOE meets the assurance requirements ASE_CCL.1, ASE_ECD.1, ASE_INT.1,
ASE_OBJ.2, ASE_REQ.2, ASE_SPD.1, ASE_TSS.1, AGD_OPE.1, AGD_PRE.1,
ADV_ARC.1, ADV_FSP.4, ADV_IMP.1, ADV_TDS.3, ALC_CMC.3, ALC_CMS.3,
ALC_DVS.1, ALC_LCD.1, ALC_TAT.1, ATE_COV.2, ATE_DPT.1, ATE_FUN.1, ATE_IND.2,
AVA_VAN.3.
The TOE Security Functional Requirements (SFR) relevant for the TOE are outlined in the
Security Target [6], chapter 6.1. They are selected from Common Criteria Part 2 and some
of them are newly defined. Thus the TOE is CC Part 2 extended.
The TOE Security Functional Requirements are implemented by the following TOE
Security Functionality:
TOE Security Functionality Addressed issue
SF.1: Secure PIN entry The PIN which identifies the user to the smartcard is entered on
the keyboard.
The TOE ensures that the PIN is only communicated to the
smartcard, but not to other parties, e.g. software on the PC
connected to the TOE.
The TOE signals to the user by lighting a dedicated LED when
it is secure to enter the PIN on the keyboard.
SF.2: Memory reprocessing The TOE ensures that no information about the PIN remain in
the TOE after it has been transmitted to the smartcard.
Table 1: TOE Security Functionalities
For more details please refer to the Security Target [6], chapter 7.
The assets to be protected by the TOE are defined in the Security Target [6], chapter 3.2.
Based on these assets the TOE Security Problem is defined in terms of Assumptions and
Threats. This is outlined in the Security Target [6], chapters 3.1 and 3.4.
This certification covers the configurations of the TOE as outlined in chapter 8.
The vulnerability assessment results as stated within this certificate do not include a rating
for those cryptographic algorithms and their implementation suitable for encryption and
decryption (see BSIG Section 9, Para. 4, Clause 2).
The certification results only apply to the version of the product indicated in the certificate
and on the condition that all the stipulations are kept as detailed in this Certification
Report. This certificate is not an endorsement of the IT product by the Federal Office for
Information Security (BSI) or any other organisation that recognises or gives effect to this
12 / 26
BSI-DSZ-CC-1046-2018 Certification Report
certificate, and no warranty of the IT product by BSI or any other organisation that
recognises or gives effect to this certificate, is either expressed or implied.
2. Identification of the TOE
The Target of Evaluation (TOE) is called:
KB100 SCR eSIG,
S26381-K101-Lx 20-*-1, FW-Version 2.0.0, HW-Version HOS: 01
The following table outlines the TOE deliverables:
No Type Identifier Release Form of Delivery7
1 HW/FW Smartcard Keyboard of the KB100 SCR eSIG
series with firmware version 2.0.0 and the product
index HOS: 01
Part numbers8
:
S26381-K101-L420-*-1 HOS: 01
and
S26381-K101-L120-*-1 HOS: 01
01 By distributor or by
special agreement
with Fujitsu
Technology
Solutions GmbH
(see notes below)
2 DOC Quick Start Guide Fujitsu KB100 SCR eSIG;
A26381-K101-Z310-1-8N19 [9]
SHA-256 checksum:
51746651DD6E1BD8DBC7E86B87996BDC
5EE797FD53E8AEED53286CD9606F1201
11/2017 Electronic
3 DOC Operating Instruction Fujitsu KB100 SCR eSIG;
A26381-K101-Z320-1-8N19 [10]
SHA-256 checksum:
3D79754C06BB4C028EB6D7F4B0630877
3CE0126EC383BFB2534F29F4C82AE71F
11/2017 Electronic
4 DOC Fujitsu KB100 SCR eSIG Software Developer’s
Guide [11]
SHA-256 checksum:
32F3717FA7C15F6D69BA8025E8B06684
0030563F401265C6652CE5E323B8C3AB
September 2017 Electronic
Table 2: Deliverables of the TOE
The TOE is a hardware device with associated guidance documents. The TOE is intended
to be used with driver software which is not in the scope of this evaluation.
The Quick Start Guide [9], the detailed Operating Instruction [10] and the Software
Developer’s Guide [11] are supplied to the user in electronic form. The documents are
available from the Fujitsu support website:
http://support.ts.fujitsu.com/IndexDownload.asp9
. The integrity of the documents is
protected using SHA-256 checksum as stated in table 2.
7
As ALC_DEL has been excluded, the delivery procedure was not in the scope of this evaluation. The form
of delivery is nevertheless described informally.
8
The TOE has only a single configuration, which cannot be changed. There are only variations in the casing
colour (marble grey, black). However, this has no impact on the security functionality. For more information,
see chapter 1.1 in the ST [6].
9
Optionally, the documents can also be enclosed on CD with the delivery. However, only the versions
distributed via the Fujitsu support website as listed in table 2 are part of the evaluated configuration.
13 / 26
Certification Report BSI-DSZ-CC-1046-2018
An authentic TOE must fulfil all of the following criteria:
● It is marked "FUJITSU" on the top of the casing.
● It has one of the following part numbers ("P/N") engraved on the bottom of the casing:
• S26381-K101-L420-*-1 HOS: 01
• S26381-K101-L120-*-1 HOS: 01
● It has four intact security seals with a lock symbol (two on the back, one each left and
right) that match the description in the user guidance (see Operating Instructions [10],
sec. "Siegelbeschreibung").
● The SHA-256 checksums of the downloaded guidance documentation matches the
values as stated in table 2.
● Due to the fact, that the Common Criteria component ALC_DEL.1 is not part of the
certification, the security review ends with the packaging process at the production line.
The delivery of the TOE to the secure environment in which the TOE will be used must
be negotiated individually with every single customer. Direct delivery to the user or
administrator is preferred.
3. Security Policy
The Security Policy is expressed by the set of Security Functional Requirements and
implemented by the TOE. It covers the following issues:
● User data protection: Access control, Residual information protection
● Identification and authentication: Protected authentication feedback
● TOE access: Default TOE access banner
● Protection of the TSF: TOE emanation, Passive detection of physical attack
4. Assumptions and Clarification of Scope
The Assumptions defined in the Security Target and some aspects of Threats and
Organisational Security Policies are not covered by the TOE itself. These aspects lead to
specific security objectives to be fulfilled by the TOE-Environment. The following topics are
of relevance:
● The TOE must be used as a smartcard keyboard for the non-public environment.
● The user must check the integrity of the security seal and the TOE.
● The user must follow the security advice of the card issuer.
● While entering the PIN, the user must check the status of the LED to ensure that the
secure PIN entry mode is active.
● The user must only use processor cards which satisfy the [12] and [13] specifications.
Details can be found in the Security Target [6], chapter 4.2.
5. Architectural Information
The functionality of the TOE is mainly provided by the firmware of the TOE's
microcontroller. The firmware consists of two subsystems; the CCID Subsystem and the
14 / 26
BSI-DSZ-CC-1046-2018 Certification Report
Misc Subsystem. The Misc Subsystem comprises basic hardware management as well as
the TOE's functionality as a regular USB keyboard. The CCID subsystem contains all
components providing security relevant services. The subsystems are further divided into
modules.
Figure 1: Architecture of the TOE
The modules shown in Figure 1 provide the following functionality:
● Misc Subsystem
• USB Module: Basic USB functions, distribution of USB messages to the HID
(keyboard) or CCID (card reader) functionality
• HID Module: Keyboard functionality, including Caps-Lock and Num-Lock LEDs
• Smartcard IO Module: Access to the card reader, control of the Data LED
• Hardware Abstraction (HAL): Access to physical hardware features, i.e. keyboard and
LEDs
● CCID Subsystem
• CCID Interface: Interpretation of CCID class USB messages
• SPE Service: Implementation of the Secure PIN Entry (SPE) functionality, including
control of the SPE LED
• Non-SPE Services: Implementation of all other card reader functionality
• Keyscan Service: Handling of key presses either in SPE or regular mode
15 / 26
Certification Report BSI-DSZ-CC-1046-2018
6. Documentation
The evaluated documentation as outlined in table 2 is being provided with the product to
the customer. This documentation contains the required information for secure usage of
the TOE in accordance with the Security Target.
Additional obligations and notes for secure usage of the TOE as outlined in chapter 10 of
this report have to be followed.
7. IT Product Testing
7.1. Developer Testing
Test Environment
The tests are performed on an actual TOE that is connected as a USB device to a virtual
machine (VM) (operating on a notebook) running the test scripts. User key presses are
simulated by an automatic keyboard tester operating the key matrix directly.
The test environment, under control of a test script, operates the USB interface and the
key matrix and checks the state of the SPE LED. Removal and insertion of test smartcards
has to be done by the test operator as prompted by the test script. The tested smart card
echoes back the data it received from the TOE, so the test script can check it against the
expected values.
The developer tests cover the following areas:
● Physical interfaces: USB, smart card, SPE LED
● USB HID class commands for non-interference with the smartcard reader functionality
● USB CCID class commands (transmission modes, functionality, PIN formats)
● SPE functionality
Test Depth and Result
The topics covered by the tests can be summarized as follows
● Misc Subsystem
• Identification of the TOE
• Reporting of capabilities (e.g. firmware version)
• HID functionality
● CCID Subsystem
• SPE operations
• Other CCID operations
• Error handling
• State of the SPE LED
• (Non-)reporting of key presses
• Functionality of the smartcard interface
16 / 26
BSI-DSZ-CC-1046-2018 Certification Report
The focus of the tests for the CCID subsystem was naturally on the SPE functionality. The
purpose of the majority of the tests is dedicated to SPE operations, covering all possible
combinations of features.
The tests are executed against the TSFIs. The more complex TSFIs adhere to universal,
well-documented standards, the others have a very limited range of possible values.
The evaluator deems the testing approach of the developer as appropriate. Especially the
systematic testing of the SPE functionality supports the confidence that the TOE's
behaviour conforms to the specifications.
The tests were reproducible and the results were in accordance with the ST and could be
matched to the expected values in the test plan.
7.2. Independent Evaluator Testing
Overview
The independent testing was performed using the developer’s testing environment,
operated by the evaluator at the evaluation lab's premises.
The overall test result is that no deviations were found between the expected and the
actual test results.
Test Configurations
The test environment provided by the developer consisted of the following items:
● Virtual Machine with all software necessary to execute the test scripts of the developer
● Test scripts of the developer
● Key Tester device to operate keyboard TFSI
● TOE prepared with adapter circuit board for use with Key Tester for fully automatic
testing
● Unmodified TOE for testing with manual interaction by the test operator.
Comparing the configuration of the unique reference of the TOE under testing with the
configuration of the TOE being under evaluation the evaluators verified that the
configuration of the samples are consistent to the configuration as stated in the ST and
with the TOE reference as managed by the CM.
Test Approach
Secure PIN Entry is the primary security feature of the TOE, so the evaluator chose for his
test subset the developer tests for this feature. All tests regarding the SPE feature that
could be executed automatically (644 tests in total) were repeated.
Additionally, the evaluator devised a set of tests that verifies the TOE behaviour for the
following cases:
● Legal alphanumeric PIN is entered
● Illegal alphanumeric PIN is entered
● Unsuitable encoding for alphanumeric PIN is used
The SFRs FDP_ACC.1, FDP_ACF.1, FDP_RIP.1 and FTA_TAB.1 are tested directly by
tests included in the evaluator subset; for FIA_UAU.7 the evaluator checked that there is
at least one test in the developer test suite. FPT_EMS.1 and FPT_PHP.1 do not directly
17 / 26
Certification Report BSI-DSZ-CC-1046-2018
concern TOE behaviour that is visible at the TSFIs and are therefore addressed in the
vulnerability assessment (AVA_VAN).
Summary
The evaluator test subset covers all SFR-enforcing and SFR-supporting TSFI in a way that
would expose incorrect behaviour of the TOE.
For the independent testing the overall test result is that no deviations were found between
the expected and the actual test results. For all test cases, the actual test results are
consistent with the expected test results.
7.3. Vulnerability Assessment
The evaluator performed a focused vulnerability assessment analysing all developer
evidences provided for evaluation and taking in consideration publicly available information
about potential vulnerabilities.
The SFR FPT_PHP.1 was tested as part of the vulnerability assessment. Penetration tests
of the security seals were performed using operational samples of the TOE. Since there
are no different configurations of the TOE, the configuration under test was consistent with
the version under evaluation.
The remaining SFRs were analysed, but not tested through penetration due to non-
exploitability of the related attack scenarios in the TOE’s operational environment.
The overall penetration test result is that no deviations were found between the expected
and the actual test results; moreover, no attack scenario with the attack potential
enhanced basic was actually successful.
Since the Common Criteria assurance component ALC_DEL.1 was not part of the
assurance activities it cannot be excluded that potential vulnerabilities in this life cycle
phase of the TOE exist. Please see the respective obligation in Chapter 10.
8. Evaluated Configuration
This certification covers the following configurations of the TOE: The TOE, the smartcard
keyboard KB100 SCR eSIG, features a USB keyboard with an integrated Class 2 reader
that is able to read processor smartcards in line with ISO 7816 [12] and EMV 2000 [13] via
various application interfaces. The keyboard works with all smartcard data transfer
protocols according to ISO 7816 [12].
The TOE has only a single configuration, which cannot be changed. There are variations in
the casing colour, i.e. marble grey (S26381-K101-L120-*-1 HOS: 01) and black (S26381-
K101-L420-*-1 HOS: 01). The product family "K101" distinguishes the TOE from other
Fujitsu smartcard keyboards that are not in scope of this evaluation.
9. Results of the Evaluation
9.1. CC specific results
The Evaluation Technical Report (ETR) [7] was provided by the ITSEF according to the
Common Criteria [1], the Methodology [2], the requirements of the Scheme [3] and all
interpretations and guidelines of the Scheme (AIS) [4] as relevant for the TOE.
The Evaluation Methodology CEM [2] was used.
18 / 26
BSI-DSZ-CC-1046-2018 Certification Report
As a result of the evaluation the verdict PASS is confirmed for the following assurance
components:
● All assurance components claimed in the Security Target [6], chapter 2.3 and defined in
the CC (see also part C of this report). Informally, this component claim corresponds to
the assurance level EAL 3 augmented by the components ADV_FSP.4, ADV_IMP.1,
ADV_TDS.3, ALC_TAT.1 and AVA.VAN.3 and reduced by the component ALC_DEL.1.
The evaluation has confirmed:
● for the Functionality: Product specific Security Target
Common Criteria Part 2 extended
● for the Assurance: Common Criteria Part 3 conformant
ASE_CCL.1, ASE_ECD.1, ASE_INT.1, ASE_OBJ.2, ASE_REQ.2,
ASE_SPD.1, ASE_TSS.1, AGD_OPE.1, AGD_PRE.1,
ADV_ARC.1, ADV_FSP.4, ADV_IMP.1, ADV_TDS.3,
ALC_CMC.3, ALC_CMS.3, ALC_DVS.1, ALC_LCD.1,
ALC_TAT.1, ATE_COV.2, ATE_DPT.1, ATE_FUN.1, ATE_IND.2,
AVA_VAN.3
The results of the evaluation are only applicable to the TOE as defined in chapter 2 and
the configuration as outlined in chapter 8 above.
9.2. Results of cryptographic assessment
The TOE does not include cryptographic mechanisms. Thus, no such mechanisms were
part of the assessment.
10. Obligations and Notes for the Usage of the TOE
The documents as outlined in table 2 contain necessary information about the usage of the
TOE and all security hints therein have to be considered. In addition all aspects of
Assumptions, Threats and OSPs as outlined in the Security Target not covered by the TOE
itself need to be fulfilled by the operational environment of the TOE.
The customer or user of the product shall consider the results of the certification within his
system risk management process. In order for the evolution of attack methods and
techniques to be covered, he should define the period of time until a re-assessment of the
TOE is required and thus requested from the sponsor of the certificate.
The limited validity for the usage of cryptographic algorithms as outlined in chapter 9 has
to be considered by the user and his system risk management process, too.
In addition, the following aspects need to be fulfilled when using the TOE:
● The delivery procedures (aspect ALC_DEL) have not been evaluated. The user must
therefore assess whether the form of delivery offered by the developer and the
possibilities to check the integrity and authenticity of the received product is adequate to
their security needs.
● Furthermore the user has to follow the security requirements stated in the user
guidance, especially in [10], section "Sicherheitshinweise", of which the main points are
summarized here:
• The TOE must be used in a non-public environment.
19 / 26
Certification Report BSI-DSZ-CC-1046-2018
• The TOE environment must be protected against installation of audio and video
recording equipment.
• The smartcard and the PIN must be kept confidential. The security advice of the card
issuer must be followed.
• The integrity and authenticity of the TOE must be verified before use by inspecting the
security seals.
• During PIN entry the user must not be observed and the Secure PIN Entry LED must
be on.
• The user must only use processor cards which satisfy the [12] and [13] specifications.
11. Security Target
For the purpose of publishing, the Security Target [6] of the Target of Evaluation (TOE) is
provided within a separate document as Annex A of this report.
12. Definitions
12.1. Acronyms
AIS Application Notes and Interpretations of the Scheme
BSI Bundesamt für Sicherheit in der Informationstechnik / Federal Office for
Information Security, Bonn, Germany
BSIG BSI-Gesetz / Act on the Federal Office for Information Security
CCID Chip Card Interface Device, an USB protocol
CCRA Common Criteria Recognition Arrangement
CC Common Criteria for IT Security Evaluation
CEM Common Methodology for Information Technology Security Evaluation
cPP Collaborative Protection Profile
DRNG Deterministic Random Number Generator
EAL Evaluation Assurance Level
EEPROM Electrically Erasable Programmable ROM
ETR Evaluation Technical Report
HID Human Interface Device, an USB protocol
IT Information Technology
ITSEF Information Technology Security Evaluation Facility
LED Light Emitting Diode
PP Protection Profile
SAR Security Assurance Requirement
SFP Security Function Policy
SFR Security Functional Requirement
20 / 26
BSI-DSZ-CC-1046-2018 Certification Report
SPE Secure PIN Entry
ST Security Target
TOE Target of Evaluation
TSF TOE Security Functionality
12.2. Glossary
Augmentation - The addition of one or more requirement(s) to a package.
Collaborative Protection Profile - A Protection Profile collaboratively developed by an
International Technical Community endorsed by the Management Committee.
Extension - The addition to an ST or PP of functional requirements not contained in CC
part 2 and/or assurance requirements not contained in CC part 3.
Formal - Expressed in a restricted syntax language with defined semantics based on well-
established mathematical concepts.
Informal - Expressed in natural language.
Object - A passive entity in the TOE, that contains or receives information, and upon which
subjects perform operations.
Package - named set of either security functional or security assurance requirements
Protection Profile - A formal document defined in CC, expressing an implementation
independent set of security requirements for a category of IT Products that meet specific
consumer needs.
Security Target - An implementation-dependent statement of security needs for a specific
identified TOE.
Semiformal - Expressed in a restricted syntax language with defined semantics.
Subject - An active entity in the TOE that performs operations on objects.
Target of Evaluation - An IT Product and its associated administrator and user guidance
documentation that is the subject of an Evaluation.
TOE Security Functionality - Combined functionality of all hardware, software, and
firmware of a TOE that must be relied upon for the correct enforcement of the SFRs.
13. Bibliography
[1] Common Criteria for Information Technology Security Evaluation, Version 3.1,
Part 1: Introduction and general model, Revision 4, September 2012,
Part 2: Security functional components, Revision 4, September 2012,
Part 3: Security assurance components, Revision 4, September 2012
http://www.commoncriteriaportal.org
[2] Common Methodology for Information Technology Security Evaluation (CEM),
Evaluation Methodology, Version 3.1, Rev. 4,September 2012,
http://www.commoncriteriaportal.org
[3] BSI certification: Scheme documentation describing the certification process (CC-
Produkte) and Scheme documentation on requirements for the Evaluation Facility,
approval and licencing (CC-Stellen), https://www.bsi.bund.de/zertifizierung
21 / 26
Certification Report BSI-DSZ-CC-1046-2018
[4] Application Notes and Interpretations of the Scheme (AIS) as relevant for the TOE10
https://www.bsi.bund.de/AIS
[5] German IT Security Certificates (BSI 7148), periodically updated list published also
on the BSI Website, https://www.bsi.bund.de/zertifizierungsreporte
[6] Security Target BSI-DSZ-CC-1046-2018, Version 1.10, 16.02.2018, Security Target
for KB100 SCR eSIG, Fujitsu Technology Solutions GmbH
[7] Evaluation Technical Report, Version 1.6, 05.03.2018, SRC Security Research &
Consulting, (confidential document)
[8] Configuration list for the TOE, Version 0.30, 16.02.2018, Konfigurationsliste
KB100SCReSIG (confidential document)
[9] Guidance documentation for the TOE, Quick Start Guide Fujitsu KB100 SCR eSIG;
Fujitsu, A26381-K101-Z310-1-8N19, 11/2017
[10] Guidance documentation for the TOE, Operating Instruction Fujitsu KB100 SCR
eSIG; Fujitsu, A26381-K101-Z320-1-8N19, 11/2017
[11] Guidance documentation for the TOE, Fujitsu KB100 SCR eSIG Software
Developer’s Guide; Fujitsu, September 2017
[12] DIN ISO 7816 - 1 Identification cards - Integrated circuit(s) cards with contacts –
Physical Characteristics
DIN ISO 7816 – 2 Identification cards - Integrated circuit(s) cards with contacts -
Dimensions and locations of the contacts
DIN ISO 7816 – 3 Identification cards - Integrated circuit(s) cards with contacts -
electrical characteristics and transmission protocols
DIN ISO 7816 – 4 Information technology - Identification cards - Integrated circuit(s)
cards with contacts - Inter - industry commands for interchange
DIN ISO 7816 – 8 Identification cards – Integrated circuit(s) cards with contacts –
Security related interindustry commands
[13] EMV 2000 Book 1 - Application independent ICC to Terminal Interface requirements,
Version 4.0, December 2000
10
specifically
• AIS 1, Version 13, Durchführung der Ortsbesichtigung in der Entwicklungsumgebung des Herstellers
• AIS 32, Version 7, CC-Interpretationen im deutschen Zertifizierungsschema
• AIS 48, Version 1, Anforderungen an die Prüfung von Sicherheitsetiketten
22 / 26
BSI-DSZ-CC-1046-2018 Certification Report
C. Excerpts from the Criteria
For the meaning of the assurance components and levels the following references to the
Common Criteria can be followed:
• On conformance claim definitions and descriptions refer to CC part 1 chapter 10.4
• On the concept of assurance classes, families and components refer to CC Part 3
chapter 7.1
• On the concept and definition of pre-defined assurance packages (EAL) refer to CC
Part 3 chapters 7.2 and 8
• On the assurance class ASE for Security Target evaluation refer to CC Part 3
chapter 11
• On the detailled definitions of the assurance components for the TOE evaluation
refer to CC Part 3 chapters 12 to 16
• The table in CC part 3 , Annex E summarizes the relationship between the
evaluation assurance levels (EAL) and the assurance classes, families and
components.
The CC are published at http://www.commoncriteriaportal.org/cc/
23 / 26
Certification Report BSI-DSZ-CC-1046-2018
This page is intentionally left blank.
24 / 26
BSI-DSZ-CC-1046-2018 Certification Report
D. Annexes
List of annexes of this certification report
Annex A: Security Target provided within a separate document.
25 / 26
Certification Report BSI-DSZ-CC-1046-2018
Note: End of report
26 / 26