bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
1 / 90
bizhub C450P / ineo+ 450P Control Software
Security Target
This document is a translation of the evaluated and certified security target
written in Japanese
Version：1.04
Issued on：June 1, 2007
Created by：
KONICA MINOLTA BUSINESS TECHNOLOGIES, INC.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
2 / 90
＜Revision History＞
Date Ver. Division Approved Checked Created Revision
2006/05/08 1.00 Development
Div. 12
Ishida Nakajima Yoshida Initial Version
2006/07/05 1.01 Development
Div. 12
Ishida Nakajima Yoshida ・Correct the list of option products
・Add the setup function description
・Delete the wrong description about FAX unit connection
2006/11/22 1.02 Development
Div. 12
Ishida Nakajima Yoshida Correct accompanying the revised ST of bizhub C450 / bizhub
C351/ ineo
+
450/ ineo
+
350 Control Software
2007/05/10 1.03 Development
Div. 12
Ishida Nakajima Yoshida Reflect the review point of other models evaluated by ISO
2007/06/01 1.04 Development
Div. 12
Ishida Nakajima Yoshida Reflect the review point of other models evaluated by ISO
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
3 / 90
―【 Contents 】――――――――――――――――――――――――――――――――
1. ST Introduction ......................................................................................................................5
1.1. ST Identification............................................................................................................................... 5
1.2. TOE Identification ............................................................................................................................ 5
1.3. CC Conformance Claim .................................................................................................................. 5
1.4. ST Overview .................................................................................................................................... 6
2. TOE Description.....................................................................................................................7
2.1. TOE Type......................................................................................................................................... 7
2.2. Environment for the usage of Printer .............................................................................................. 7
2.3. Operation Environment of the TOE................................................................................................. 8
2.4. Role of the TOE User ...................................................................................................................... 9
2.5. Functions provided by the TOE..................................................................................................... 10
2.5.1. Basic Function ..........................................................................................................................................10
2.5.2. User Box Function ....................................................................................................................................10
2.5.3. Administrator Function ..............................................................................................................................11
2.5.4. Service Engineer Function ........................................................................................................................12
2.5.5. Other Functions ........................................................................................................................................12
2.5.6. Enhanced Security Function......................................................................................................................14
3. TOE Security Environment..................................................................................................15
3.1. Concept of Protected Assets......................................................................................................... 15
3.2. Assumptions .................................................................................................................................. 16
3.3. Threats........................................................................................................................................... 16
3.4. Organizational Security Policies.................................................................................................... 17
4. Security Objectives..............................................................................................................18
4.1. Security Objectives for the TOE.................................................................................................... 18
4.2. Security objectives for the environment........................................................................................ 18
4.2.1. IT environment security objectives.............................................................................................................19
4.2.2. Non-IT environment security objective .......................................................................................................19
5. IT Security Requirements....................................................................................................21
5.1. TOE Security Requirements.......................................................................................................... 21
5.1.1. TOE Security Function Requirements........................................................................................................21
5.1.2. Minimum Security Strength of Function......................................................................................................38
5.1.3. TOE Security Assurance Requirements .....................................................................................................38
5.2. Security Requirements for the IT environment ............................................................................. 38
6. TOE Summary Specification ...............................................................................................41
6.1. TOE Security Functions................................................................................................................. 41
6.1.1. F.ADMIN（Administrator Function） .............................................................................................................41
6.1.2. F.ADMIN-SNMP（SNMP administrator function）.........................................................................................46
6.1.3. F.SERVICE（Service mode function）..........................................................................................................47
6.1.4. F.BOX（User Box Function） .......................................................................................................................49
6.1.5. F.PRINT（Secure Print Function） ...............................................................................................................50
6.1.6. F.OVERWRITE-ALL（All area overwrite deletion function） ..........................................................................51
6.1.7. F.CRYPT（Encryption key generation function） ..........................................................................................52
6.1.8. F.HDD（HDD verification function） .............................................................................................................52
6.1.9. F.RESET（Authentication Failure Frequency Reset Function）.....................................................................52
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
4 / 90
6.2. TOE Security Strength of Function................................................................................................ 52
6.3. Correspondence between TOE Security Functions and Function Requirements........................ 53
6.4. Assurance Measures..................................................................................................................... 53
7. PP Claims .............................................................................................................................55
8. Rational.................................................................................................................................56
8.1. Security Objectives Rationale ....................................................................................................... 56
8.1.1. Necessity..................................................................................................................................................56
8.1.2. Sufficiency of Assumptions........................................................................................................................57
8.1.3. Sufficiency of Threats................................................................................................................................57
8.1.4. Sufficiency of Organizational Security Policies ...........................................................................................59
8.2. IT Security Requirements Rationale ............................................................................................. 59
8.2.1. Rationale for IT Security Functional Requirements.....................................................................................59
8.2.2. Rational for Minimum Strength of Function ................................................................................................75
8.2.3. Rationale for IT Security Assurance Requirements.....................................................................................75
8.2.4. Consistency rationale for the set of IT security functional requirement ........................................................75
8.3. Rational for TOE Summary Specifications.................................................................................... 76
8.3.1. Rational for the TOE Security Functions ....................................................................................................76
8.3.2. Rational for TOE Security Strength of Function ..........................................................................................89
8.3.3. Mutually Supported TOE Security Functions..............................................................................................89
8.3.4. Rationale for Assurance Measures............................................................................................................89
8.4. PP calims rationale........................................................................................................................ 90
―【 List of Figures 】――――――――――――――――――――――――――――
Figure 1 An example of the expected environment for usage of the Printer.................................... 7
Figure 2 Hardware composition that relates to TOE......................................................................... 8
―【 List of Tables 】―――――――――――――――――――――――――――――
Table 1 User Box Access Control Operational List ......................................................................... 22
Table 2 Secure Print File Access Control: Operational List ............................................................. 22
Table 3 Setting Management Access Control: Operational List....................................................... 23
Table 4 TOE Security Assurance Requirements .............................................................................. 38
Table 5: The list of the name and identifier of TOE Security function.............................................. 41
Table 6 Character and number of digits used for password............................................................. 42
Table 7 A type of overwrite deletion of all area and the method of overwriting................................ 44
Table 8 Correspondence between TOE Assurance Requirements and assurance measures ....... 53
Table 9 Conformity of Security Objectives to assumptions and Threats ......................................... 56
Table 10 Conformity of IT Security Functional Requirements to Security Objectives ..................... 60
Table 11 Dependencies of IT Security Functional Requirements Components............................... 69
Table 12 Mutual Support Correlations of IT Security Functional Requirements.............................. 71
Table 13 Conformity of TOE Security Functions to TOE Security Functional Requirements.......... 76
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
5 / 90
1. ST Introduction
1.1. ST Identification
・ST Title ： bizhub C450P / ineo+ 450P Control Software
Security Target
・ST Version ： 1.04
・CC Version ： 2.3
・Created on ： June 1, 2007
・Created by ： KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. Eiichi Yoshida
1.2. TOE Identification
・TOE Name ： Japan：bizhub C450P / ineo+ 450P Zentai Seigyo Software
Overseas：bizhub C450P / ineo+ 450P Control Software
・TOE Version ： 4037-0100-GM0-11-000
・TOE Type ： Software
・Created by ： KONICA MINOLTA BUSINESS TECHNOLOGIES, INC.
1.3. CC Conformance Claim
The TOE, which is the subject of this ST, conforms to the following.
Security function requirement
Part2 Extended
Security assurance requirement
Part3 Conformant
Evaluation assurance level
EAL3 Conformant (No additional assurance component)
PP Reference
This ST does not carry out a PP reference.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
6 / 90
Reference
・ Common Criteria for Information Technology Security Evaluation Part 1:Introduction and
general model 2005 Version 2.3 CCMB-2005-08-001
・ Common Criteria for Information Technology Security Evaluation Part 2:Security
functional requirements 2005 Version 2.3 CCMB-2005-08-002
・ Common Criteria for Information Technology Security Evaluation Part 3:Security
assurance requirements 2005 Version 2.3 CCMB-2005-08-003
・ Common Criteria for Information Technology Security Evaluation Part 1: Introduction and
General Model August 2005 Version 2.3 CCMB-2005-08-001
(December 2005 Translation Version 1.0, Information-technology Promotion Agency
Japan, Security Center）
・ Common Criteria for Information Technology Security Evaluation Part 2: Security
Functional Requirements August 2005 Version 2.3 CCMB-2005-08-002
(December 2005 Translation Version 1.0, Information-technology Promotion Agency
Japan, Security Center）
・ Common Criteria for Information Technology Security Evaluation Part 3: Security
Assurance Requirements August 2005 Version 2.3 CCMB-2005-08-003
(December 2005 Translation Version 1.0, Information-technology Promotion Agency
Japan, Security Center）
・ Interpretations - 0512 (December 2005 Information-technology Promotion Agency Japan,
Security Center, Information Security Certification Office）
1.4. ST Overview
bizhub C450P/ ineo+ 450P is Konica Minolta Business Technologies, Inc. network printer.
（Hereafter, “Printer” as all these generic names）. The target of evaluation (TOE) of this
Security Target (ST) is the “bizhub C450P / ineo+ 450P Control Software,” that controls the entire
operation of the printer, including the operation control processing and the image data
management that are accepting from the panel of the main body of the printer or through the
network. This ST explains the security functions that are realized by the TOE.
TOE offers the protection from exposure of the highly confidential document stored in the
printer. Moreover, TOE can encrypt the image data written in HDD for the danger of taking
HDD that is the medium that stores the image data in the printer out illegally by installing the
encryption board which is the option parts of the printer. Besides, TOE has the deletion method
to follow various overwrite deletion standards. It deletes all the data of HDD completely and it
contributes to the prevention of the divulging information of the organization that uses the
printer by using the method at the time of abandonment or the lease returns.
This ST is the documentation for describing the necessity and sufficiency of these TOE
Security Functions.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
7 / 90
2. TOE Description
2.1. TOE Type
The bizhub C450P / ineo+ 450P Control Software that is the TOE is an embedded software
product that controls the operation of whole printer overall in the flash memory on the printer
controller.
2.2. Environment for the usage of Printer
Figure 1 shows the expected general environment for the usage of the printer equipped with
TOE. Moreover, the matters, assumed in the environment for the usage, show by a run of the
item below
Figure 1 An example of the expected environment for usage of the Printer
The intra-office LAN exists as a network in the office.
The printer connects to the client PCs via the intra-office LAN, and has mutual data
communication.
When the intra-office LAN connects to an external network, measures such as connecting via
a firewall are taken, and an appropriate setup to block access requests to the printer from the
external network is carried out.
The intra-office LAN provides a network environment that cannot be intercepted by the office
operation including using the switching hub and installing the wiretapping detector.
Internet
External Network
Office
Client PC
Firewall
オフィス内 LAN
Printer TOE
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
8 / 90
2.3. Operation Environment of the TOE
Figure 2 Hardware composition that relates to TOE
Figure2 shows the structure of the hardware environment on the printer that TOE needs for
the operation. TOE exists on the flash memory on the printer controller which builds in the body
of the printer and is loaded and run on the RAM.
The following explains about the unique hardware on the printer controller, the hardware
having the interface to the printer controller, and the connection by using RS-232C, shown in
Figure 2.
Flash memory
Storage medium that stores the object code of the “Printer Control Software” that is the TOE.
Additionally, it stores the message data of each country’s language to display the response
accessed through the panel and network, OS (VxWorks), and so on.
HDD (※Optional Part)
Hard disk drive of 40GB in capacity. It is utilized besides the image data is stored as a file,
temporarily image data with such as extension conversion, and as an area where the
transmission address data kept.
As a feature function, the security function (HDD lock function) is installed, being possible to
set the password and not being possible to read and write unless it agrees to the password.
Furthermore, when the frequency of uniformity of it becomes unsuccessful in password
collation, the function is also ready to lock the password collation function.
NVRAM
Nonvolatile Memory. The memory medium that stores various setting values needed for the
operation of the printer used for processing of TOE.
RAM
CPU
* Local
Connecting Unit
Client PC
RS-232C
* HDD NVRAM
Printer
Unit
Paper
Ethernet
Printer Controller
・OS
・Message Data
etc.
・ TOE
Panel
Operator
Network
Unit
Flash Memory
*Encryption
Board
2 lines LCD panel
Printer
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
9 / 90
Encryption Board（※Optional Part）
The hardware-based cryptographic function, which is the integrated circuit for encryption, is
installed in order to encipher all data to be written in HDD. It is not pre-installed in printer as
standard for convenience' sake of a sale, but is sold as an optional part.
2 Lines LCD Panel
The exclusive control device for the operation of the printer equipped with the 2lines LCD
panel of a liquid crystal monitor, ten-key, cursor key, menu/select key, cancel key.
Main power supply
The power switch for activating Printer
Network Unit
The interface device to connect to the Ethernet. It supports 10BASE-T and 100BASE-TX.
Local Connecting Unit（※Optional part）
A unit that uses Print function with local connection by connecting using the client PC and
USB or parallel port. According to the circumstances in sales, it is sold as the option part and
is not attached on the printer.
RS-232C
The serial can be connected through the D-sub9 pin. When breaking down, the maintenance
function can be used through this. In addition, it can utilize a remote diagnostic function
(later description) to connect with the modem connected with the public circuit.
2.4. Role of the TOE User
The roles of the personnel that relate to the use of the printer with the TOE are defined as
follows.
User
Printer’s user who performs a printing from PC by using printer.（In general, the employee in
the office is assumed.）
Administrator
Printer's user who carries out the management of the operation of the printer. An
administrator performs the operation management of the printer and the management of
users. (In general, it is assumed that the person elected from the employees in the office plays
this role.）
Service Engineers
A user who performs management of maintenance for the printer. Service Engineer performs
the repair and adjustment of printer. (In general, the person in charge at the sales companies
that performs the maintenance service of printer and is in cooperation with Konica Minolta
Business Technologies Inc. is assumed.)
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
10 / 90
Person in charge at the Organization that uses the printer
A person in charge at the organization that manages the office where the printer is installed.
This person assigns an administrator who carries out the management of the operation of the
printer.
Person in charge at the Organization that manages the Maintenance of the printer
A person in charge at the organization that carries out management of the maintenance for
the printer. This person assigns service engineers who perform the maintenance management
for the printer.
Besides this, though not a user of TOE, a person who goes in and out the office are assumed as
an accessible person to TOE.
2.5. Functions provided by the TOE
A user uses a variety of functions of the TOE from the panel and a client PC via the network.
The following explains typical functions, such as the basic function, the user box function to
manage the image files stored, the user identification and authentication function, the
administrator function manipulated by administrator, the service engineer function
manipulated by service engineer, and the function operated in the background without the user's
awareness.
2.5.1. Basic Function
In Printer, the function to accept the print from PC exists, and TOE performs the core control
in the operation of these functions. It converts the raw data acquired from the external device of
the printer controller into the image file, and registered in RAM and HDD. (After two or more
conversion processing is done, the compression conversion is done as for the print image file from
PC.) The image file which has been compressed is decompressed into data for the print or for the
transmission, and is transmitted to the device outside of the printer controller concerned.
Operations of print is managed by the unit of job, and can be cancelled the operation, by the
command from the panel.
The following is the functions related to the security in the basic function.
Secure Print Function
When the secure print password is received with the printing data, the image file is stored as
the standby status. And the print command and password input from the panel allows
printing.
This function, in the printing operation by the PC, removes the possibility that other users
stole a glance at the printing of high-leveled confidential data and lost it into the other
printings.
2.5.2. User Box Function
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
11 / 90
The directory named “user box” can be created as an area to store the image file in HDD. The
access of a user is controlled by the password set for the user box.
TOE processes the following required operation, against the user box or the image file in a user
box for an operation requests that is transmitted from the panel or the network unit through a
network from a client PC.
Print of image file in a user box, move and copy it to other user boxes
Deletion of the image file in the user box,
Storage period setting of image file in the user box (Delete automatically after the period
passes.)
Change of the user box name, change of the password, and deletion of the user box, etc.
2.5.3. Administrator Function
TOE provides the functions such as the management of the user boxes and management of
various settings of the network, image quality, etc in the administrator mode that only
authenticated administrator can manipulate.
The following shows the function related to the security.
Management of user box settings
Registration and change of user box password
Management of network setting
IP address, NetBIOS name and AppleTalk printer name etc.
Backup and restore function of NVRAM and HDD
It is performed through the network by using an application exclusive use for the
management installed in the client PC.
Complete overwrite deletion function of HDD
There is the data deletion method conformed to various military standards.
When it's started, in conformity with a set method, the overwrite deletion is executed for
all area of HDD.
Format function of HDD
A logical format is executable.
The followings are the operation setting function related especially to the behavior of the
security function.
Setting of a password policy function
Select ON or OFF for the function to check the several conditions of the password, such as
the valid number of digits for the various passwords, etc.
Setting of the authentication method of secure print and the prohibit function of
authenticating operations.
There are the mode that the authentication operation prohibition function operates for the
authentication of the secure print, and the mode not done.
The operation mode of the function that the failure authentication in each authentication
function detects the failure synchronizes, too.
Selecting the above-mentioned operational mode
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
12 / 90
Setting of the network setting modification function by SNMPv1 and v2.
Select the permission or the prohibition of the modification operation function of MIB by
SNMPv1 and v2
Setting of HDD lock function
Selecting ON or OFF.
Register or change the HDD lock password when ON is selected.
Setting of encryption function（※only when the encryption board installed）
Selecting ON or OFF.
Register or change the Encryption passphrase when ON is selected.
Setting of user box collective management function
Select the permission or the prohibition for the user box collective management function.
Setting of the print capture function
A function to verify the print data received by MFP when print function breaks down.
Selecting ON or OFF for the above-mentioned function.
Setting of network setting management reset function
A network setting management reset function resets a series of items in a factory default.
Selecting permission or prohibition for the above-mentioned function.
2.5.4. Service Engineer Function
TOE provides a management function of administrator and a maintenance function, such as
adjusting the device for Print etc, within the service mode that only a service engineer can
operate. The following shows the functions related to the security.
Modification function of administrator password
The followings are the operation setting function related especially to the behavior of the
security function.
Setting of remote diagnostic function (later description)
Able to select permission or prohibition.
Setting of a TOE update function via Internet
Able to select permission or prohibition.
Setting of maintenance function
Able to select permission or prohibition.
The format function of HDD
A logical format and a physical format are executable.
Installation setting of HDD
An explicit installation setting is necessary to use HDD as a data storage area.
Initialization function
The various setting values that the user or the administrator has set and the data that the
user has stored are deleted.
2.5.5. Other Functions
TOE provides the functions that run background without awareness of the user and the
updating function of TOE. The following explains the major functions.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
13 / 90
① Encryption key generation function
When the encryption board, an optional product, is installed in printer controller, the
encoding and decoding is processed on the encryption board due to the reading and writing
data in HDD. (TOE does not process the encryption and description itself.)
The operation setting of this function is performed by the administrator function. When it
operates, TOE generates the encryption key by the encryption passphrase that was entered
on the panel.
② HDD Lock Function
HDD has the HDD lock function as measure against the illegal taking out, when the
password is set.
The administrator function does the operation setting of this function. As for the starting
operation of printer, the access to HDD is permitted by the matching of the HDD lock
password set to the HDD and the one set on the printer. (Even if HDD is taken out, it is
impossible to use it excluding the printer that the concerned HDD installed.)
③ Remote diagnostic function
Making use of several connected systems such as E-mail, and a modem connection through a
RS-232C, in communication with support center of printer produced by Konica Minolta
business technologies Ltd., it manages the state condition of printer and the machinery
information such as frequency of printing. In addition, if necessary, appropriate service
(shipment of an additional toner, the account claim, dispatch of the service engineer due to
the failure diagnosis, etc.) is provided.
④ Updating function of TOE
TOE facilitated with the function to update itself. As for the update means, there are a
method that exists as one of items of remote diagnostic function, a method that downloads
from FTP server through Ethernet (TOE update function via Internet), and a method that
performs the connection of the Compact Flash memory medium.
⑤ Setup function
It offers the function to setup by using the installed software dedicated to perform on PC
with connecting to client PC through RS-232C. It especially shows the operation setting
function related to the behaviour of security function in this setup function. Dedicated
installed software is used by service engineer and so it’s not offered to a user.
Setting of remote diagnostic function (later description)
・ Able to select permission or prohibition
Setting of a TOE update function via Internet
・ Able to select permission or prohibition
Setting of maintenance function
・ Able to select permission or prohibition
The format function of HDD
・ A logical format and a physical format are executable
Installation setting of HDD
・ An explicit installation setting is necessary to use HDD as a data storage area
Initialization function
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
14 / 90
・ The various setting values that the user or the administrator has set and the data
that the user has stored are deleted
2.5.6. Enhanced Security Function
Various setting functions related to the behavior of the security function for the Administrator
function and the Service engineer function can be set collectively to the secure values by the
operation settings of the “Enhanced Security Function”. Each value set is prohibited changing
itself into the vulnerable one individually. As the function that does not have a setting function of
the operation individually, there is the reset function of the network setting and the update
function of TOE through the network, but the use of these functions is prohibited.
The following explains the series of the setting condition of being the enhanced security function
active. In order to activate the enhanced security function, the prerequisite is required that an
administrator password and a CE password should be set along with the password policy.
Setting of password policy function ：Valid
Setting of secure print authentication method
： Authentication operation prohibition function
effective method (In conjunction with it, it becomes
in the state of the panel lock for five seconds at the
time of the authentication failure in the panel. And
it becomes the account lock (Failure frequency
threshold: 1-3 times) as well.)
Setting of user box collective management function
：Prohibit
Setting of the network setting modification function with SNMPv1 and v2
：Prohibit
Setting of HDD lock function ：Valid
Setting of Encryption function ：Valid
Setting of print capture function ：Prohibit
Setting of maintenance function ：Prohibit
Remote diagnostic function ：Prohibit
Network setting management reset function
：Prohibit
TOE update function via Internet ：Prohibit
The following function becomes the setup status showing below with the timing enabling the
enhanced security function. Unlike above functions, it is possible to change the setting
individually. However, when the setting is enabled, this has the system to report that status on
the 2 lines LCD panel for not satisfying the enhanced security conditions.
Setup function ：Prohibit
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
15 / 90
3. TOE Security Environment
This chapter will describe the concept of protected assets, assumptions, threats, and
organizational security policies.
3.1. Concept of Protected Assets
Security concept of TOE is “the protection of data that can be disclosed against the intention of
the user”. As printer is generally used, the following image file in available situation becomes
the protected assets. (The following image files are able to be handled only when HDD is
installed. It's assumed that the option HDD is installed on the printer in TOE security
environment.)
Secured print file
image file registered by secured print
User Box file
image file stored in the personal user box and public user box)
As for a image file of a job kept as a wait state by activities of plural jobs, and a image file of a
job kept that prints the remainder of copies becoming as a wait state for confirmation of the
finish, and other than the image file dealt with the above-mentioned is not intended to be
protected in the general use of MFP, so that it is not treated as the protected assets.
In the print of the secure print file and the transmission of the user box file, making in the
preparation for the threat thought when illegal printer or mail server is connected by any chance,
the setting of printer (IP address etc.) requires not to be modified illegally. Therefore, the setting
of printer (IP address etc.) is considered as subsidiary protected assets.
On the other hand, when the stored data have physically been separated from the jurisdiction
of a user, such as the use of printer ended by the lease return or being disposed, or the case of an
HDD theft, a user has concerns about leak possibility of every remaining data. Therefore, in this
case, the following data files become protected assets.
Secure Print File
User Box File
On Memory Image File
Image file of job in the wait state
Stored Image File
Stored image files other than secure print file and user box file
Remaining Image File
The file which remains in the HDD data area that is not deleted only by general
deletion operation (deletion of a file maintenance area)
File related to the Image
Temporary data file generated in print image file processing
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
16 / 90
3.2. Assumptions
The present section identifies and describes the assumptions for the environment for using the
TOE.
A.ADMIN（Personnel conditions to be an administrator）
Administrators, in the role given to them, will not carry out a malicious act during the series of
permitted operations given to them.
A.SERVICE（Personnel conditions to be a service engineer）
Service engineers, in the role given to them, will not carry out a malicious act during series of
permitted operations given to them.
A.NETWORK（Network connection conditions for printer）
・The intra-office LAN where the printer with the TOE will be installed is not intercepted.
・When the intra-office LAN where the printer with the TOE will be installed is connected to
an external network, access from the external network to the printer is not allowed.
A.SECRET（Operational condition about secret information）
Each password and encryption passphrase does not leak from each user in the use of TOE.
A.SETTING（Operational setting condition of Enhanced Security function）
Printer with the TOE is used after enabling the enhanced security function.
3.3. Threats
In this section, threats that are expected during the use of the TOE and the environment for
using the TOE are identified and described.
T.DISCARD-PRINTER（Lease-return and disposal of Printer）
When the leaser returned or the discarded printer were collected, secure print file, a user box
file, on memory image file, the stored image file, the remaining image file, the image-related
file, and the set various passwords (administrator password, SNMP password, HDD lock
password, encryption passphrase, secure print password, user box password) can leak by the
person with malicious intent taking out and analyzing an HDD in printer.
T.BRING-OUT-STORAGE（An unauthorized carrying out of HDD）
・A secure print file, a user box file, a on-memory image file, a stored image file, a remaining
image file, an image-related file, and the set-up various passwords (secure print password,
user box password) can leak by a person or a user with malicious intent illegally taking out
and analyzing an HDD in printer.
・A person or a user with malicious intent illegally replaces an HDD in printer. In the replaced
HDD, new files of the secure print file, a user box file, on-memory image file, a stored image
file, a remaining image file, an image related file, and set various passwords are
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
17 / 90
accumulated. A person or a user with malicious intent takes out and analyzes the replaced
HDD and image files leak.
T.ACCESS-BOX（Unauthorized access to the user box which used a user function）
Exposure of the user box file when a person or a user with malicious intent accesses the user
box which is not permitted to use by printing a user box file
T.ACCESS-SECURE-PRINT（Unauthorized access to the secure print file which used a user
function）
Exposure of the secure print file when a person or the user with malicious intent prints the
secure print file which is not permitted to use.
T.ACCESS-NET-SETTING（An unauthorized change of network setting）
Malicious person or user changes the network setting which set in printer to identify printer
itself where TOE installed, by setting to the value of the entity such as another illegal printer
from the value of printer (NetBIOS name, AppleTalk printer name, IP address etc) that TOE is
originally installed, so that secure print file is exposed.
T.ACCESS-SETTING（An unauthorized change of a function setting condition related to
security）
The possibility of leaking a user box file and secure print file rises because malicious person or
user changes the settings related to the enhanced security function.
T.BACKUP-RESTORE（Unauthorized use of Backup function and restoration function）
The user box file and the secure print file can leak by malicious person or user using the
backup function and the restoration function illegally. Also highly confidential data such as
password can be exposed and each setting values are falsified.
3.4. Organizational Security Policies
There is no organizational security policy assumed to be applied to this TOE.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
18 / 90
4. Security Objectives
In this chapter, in relation to the assumptions, the threats, and the organizational security
policy identified in Chapter 3, the required security objectives policy for the TOE and the
environment for the usage of the TOE are described by being divided into the categories of the
security objectives for the TOE and the security objectives for the environment, as follows.
4.1. Security Objectives for the TOE
In this section, the security objectives for the TOE is identified and described.
O.BOX（User box access control）
・TOE permits the user functions of the user box and the user box file in the user box only to
the user who is permitted the use of this user box.
O.SECURE-PRINT（Secure print file access control）
TOE permits the print of the secure print file only to the user who is permitted the use of this
secure print file.
O.CONFIG（Access limitation to management function）
TOE permits only the administrator the operations of the following functions.
・The setting function related to the network address of printer
・Backup function
・Restoration function
TOE permits the operations of the following functions only to the administrator and the
service engineer.
・The function related to the setting of Enhanced Security function
O.OVERWRITE-ALL（Complete overwrite deletion）
TOE overwrites all data regions of HDD in printer by using the data for deletion, and makes
impossible the restoration of all the image data. In addition, TOE offers a function to initialize
a setting value such as the highly confidential password on NVRAM that is set by a user or an
administrator. (Administrator password, SNMP password, HDD lock password, Encryption
Passphrase)
O.CRYPT-KEY（Encryption key generation）
TOE generates the encryption key to encrypt and store all data including the image file
written in HDD in printer.
O.CHECK-HDD（Validity confirmation of HDD）
TOE verifies that the correct HDD is installed.
4.2. Security objectives for the environment
In this section, the security objectives for the environment, in the environment of the usage of
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
19 / 90
the TOE, is identified and described being divided into the IT environment security objectives
and the non-IT environment security objectives.
4.2.1. IT environment security objectives
OE.CRYPT（Encryption of HDD）
An encryption board installed in printer encrypts all data including an image file to be written
in the HDD inside printer and then stores it to the HDD.
OE.LOCK-HDD（Access control of HDD）
An HDD installed in printer accepts reading out of data only from the printer where this HDD
is installed.
OE.FEED-BACK（Feedback of password）
The application of a browser etc. used by client PC to access printer offers the appropriate
feedback protected for input the user box password and administrator password.
4.2.2. Non-IT environment security objective
OE-N.ADMIN（A reliable administrator）
The person in charge in the organization who uses the printer will assign a person who can
faithfully execute the given role during the operation of the printer with TOE as an
administrator.
OE-N.SERVICE（The service engineer's guarantee）
・The person in charge in the organization that carries out the maintenance management of
the printer educates a service engineer in order to faithfully carry out the given role for the
installation of the TOE, the set up of TOE and the maintenance of a printer with TOE.
・The administrator observes the maintenance work of a printer with TOE by a service
engineer.
OE-N.NETWORK（Network Environment in which the printer is connected）
・The person in charge in the organization who uses the printer carries out the tapping
prevention measures by setting the cipher communications equipment and the tapping
detection equipment to the LAN of the office where the printer with TOE is installed.
・The person in charge in the organization who uses the printer carries out the measures for
the unauthorized access from the outside by setting up the equipment such as the firewall to
intercept the access from an external network to the printer with TOE.
OE-N.SECRET（Appropriate management of confidential information）
The administrator has the user implement the following operation.
・Keep the user password and secure print password confidential.
・Keep the user box password confidential between the user who commonly utilizes it.
・Should not set the value that can be guessed for the secure print password and the user box
password.
・The user box password should be properly changed.
・When the administrator changes the user box password, make the user to change them
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
20 / 90
promptly.
The administrator executes the following operation.
・Should not set the value that can be guessed for the administrator password, SNMP
password, the HDD lock password and encryption passphrase.
・Keep the administrator password, the SNMP password, the HDD lock password, and the
encryption passphrase confidential.
・The administrator password, the SNMP password, the HDD lock password, and the
encryption Passphrase should be properly changed.
The service engineer executes the following operation.
・Should not set the value that can be guessed for the CE password.
・Keep the CE password confidential.
・The CE password should be properly changed.
・When the service engineer changes the administrator password, make the administrator to
change it promptly.
OE-N.SESSION（Termination of session after operation）
The administrator has the user implement the following operation.
・After the operation of the secure print file and the operation of user box and user box file end,
the logoff operation is performed.
The administrator executes the following operation.
・After the operation of the various function in administrator mode ends, the logoff operation is
performed
The service engineer executes the following operation.
・After the operation of the various function in service mode ends, the logoff operation is
performed.
OE-N.SETTING-SECURITY（Operation setting of Enhanced Security function）
The administrator makes the setting of the enhanced security function effective for the
operation of TOE.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
21 / 90
5. IT Security Requirements
In this chapter, the TOE security requirements and IT environment security requirements are
described.
＜Definition of Label＞
The security function requirements required for the TOE and IT environment are described.
Those regulated in CC Part 2 will be directly used for the functional requirements components,
and the same labels will be used as well. The new additional requirement which is not described
in CC part 2 is newly established and identified with the label that doesn't compete with CC part
2. In addition, [E] is added at the end of a label of a requirement needed in IT environment in
order to state it clearly whether an object of each requirement is TOE or IT environment.
< Method of specifying security function requirement "Operation" >
In the following description, when items are indicated in “italic” and “bold,” it means that they
are assigned or selected. When items are indicated in “italic” and “bold” with parenthesis right
after the underlined original sentences, it means that the underlined sentences are refined. A
number in the parentheses after a label means that the functional requirement is used
repeatedly. (The number to indicate the repetition is added with separating respectively by TOE
requirement and IT environmental requirement.)
＜Method of clear indication of dependency＞
The label in the parentheses “( )” in the dependent section indicates a label for the security
functional requirements used in this ST. When it is a dependency that is not required to be used
in this ST, it is described as “N/A” in the same parentheses.
5.1. TOE Security Requirements
5.1.1. TOE Security Function Requirements
5.1.1.1. Cryptographic Support
FCS_CKM.1 Cryptographic key generation
FCS_CKM.1.1
The TSF shall generate cryptographic keys in accordance with a specified cryptographic key generation
algorithm [assignment: cryptographic key generation algorithm] and specified cryptographic key sizes
[assignment: cryptographic key sizes] that meet the following: [assignment: list of standards].
[assignment: list of standards]：
Konica Minolta Encryption specification standard
[assignment: cryptographic key generation algorithm]：
Konica Minolta HDD Encryption key generation algorithm (SHA-1)
[assignment: cryptographic key sizes]：
128bit
Hierarchical to ： No other components
Dependencies ： FCS_CKM.2 or FCS_COP.1（FCS_COP.1[E]）
、FCS_CKM.4（N/A）
、
FMT_MSA.2（N/A）
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
22 / 90
5.1.1.2. User data protection
FDP_ACC.1[1] Subset access control
FDP_ACC.1.1[1]
The TSF shall enforce the [assignment: access control SFP] on [assignment: list of subjects, objects, and
operations among subjects and objects covered by the SFP].
[assignment: list of subjects, objects, and operations among subjects and objects covered by the SFP]：
Listed in 「Table1 User Box Access Control Operational List」
[assignment: access control SFP]：
User Box access control
Hierarchical to ： No other components
Dependencies ： FDP_ACF.1（FDP_ACF.1[1]）
Table 1 User Box Access Control Operational List
Subject Object Operational List
A task to act for a user User Box File ・Print
・Move to other user boxes
・Copy to other user boxes
・Backup
FDP_ACC.1[2] Subset access control
FDP_ACC.1.1[2]
The TSF shall enforce the [assignment: access control SFP] on [assignment: list of subjects, objects, and
operations among subjects and objects covered by the SFP].
[assignment: list of subjects, objects, and operations among subjects and objects covered by the SFP]：
Listed in 「Tabel2 Secure print file access control operational list」
[assignment: access control SFP]：
Secure print file access control
Hierarchical to ： No other components
Dependencies ： FDP_ACF.1（FDP_ACF.1[2]）
Table 2 Secure Print File Access Control: Operational List
Subject Object Operational list
A task to act for a user Secure Print File Access Control ・Print
・Back-Up
FDP_ACC.1[3] Subset access control
FDP_ACC.1.1[3]
The TSF shall enforce the [assignment: access control SFP] on [assignment: list of subjects, objects, and
operations among subjects and objects covered by the SFP].
[assignment: list of subjects, objects, and operations among subjects and objects covered by the SFP]：
Listed in 「Table 3 Setting management access control operational list」
[assignment: access control SFP]：
Setting management access control
Hierarchical to ： No other components
Dependencies ： FDP_ACF.1（FDP_ACF.1[3]）
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
23 / 90
Table 3 Setting Management Access Control: Operational List
Subject Object Operational list
・HDD Lock Password Object
・Encryption passphrase Object
・ Settings
・ Back-Up
・ Restore
A task to act for a user
・Printer Address Group Object 1 ・ Settings
・ Restore
FDP_ACF.1[1] Security attribute based access control
FDP_ACF.1.1[1]
The TSF shall enforce the [assignment: access control SFP] to objects based on the following: [assignment:
list of subjects and objects controlled under the indicated SFP, and for each, the SFP-relevant security
attributes, or named groups of SFP-relevant security attributes].
[assignment: list of subjects and objects controlled under the indicated SFP, and for each, the
SFP-relevant security attributes, or named groups of SFP-relevant security attributes]：
＜Subject＞ ＜Subject attributes＞
・A task to act for a user ⇒ ・User Box Attributes（User Box ID）
・Administrator Attributes
----------------------------------------------------------------------------------------------------------------------------------------------
＜Object＞ ＜Object attributes＞
・User Box File ⇒ ・User Box Attributes（User Box ID）
[assignment: access control SFP]：
User Box access control
FDP_ACF.1.2[1]
The TSF shall enforce the following rules to determine if an operation among controlled subjects and
controlled objects is allowed: [assignment: rules governing access among controlled subjects and
controlled objects using controlled operations on controlled objects].
[assignment: rules governing access among controlled subjects and controlled objects using controlled
operations on controlled objects] ：
・ A task to act for a user who is related to the user box attributes (user box ID) is permitted to print,
move to other user boxes and copy to the other user boxes, to the user box file that have the matched
user box attributes with the user box attributes (user box ID) of the subject attributes.
・ A task to act for a user who has an administrator attribute is permitted to backup a user box file.
FDP_ACF.1.3[1]
The TSF shall explicitly authorize access of subjects to objects based on the following additional rules:
[assignment: rules, based on security attributes, that explicitly authorise access of subjects to objects].
[assignment: rules, based on security attributes, that explicitly authorise access of subjects to objects]：
None
FDP_ACF.1.4[1]
The TSF shall explicitly deny access of subjects to objects based on the [assignment: rules, based on
security attributes, that explicitly deny access of subjects to objects].
[assignment: rules, based on security attributes, that explicitly deny access of subjects to objects] ：
None
Hierarchical to ： No other components
Dependencies ： FDP_ACC.1（FDP_ACC.1[1]）
、FMT_MSA.3（N/A）
FDP_ACF.1[2] Security attribute based access control
FDP_ACF.1.1[2]
The TSF shall enforce the [assignment: access control SFP] to objects based on the following: [assignment:
1
The Printer address group object is a series of data concerning the address of the main body of printer such as IP
address and the Appletalk printer name.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
24 / 90
list of subjects and objects controlled under the indicated SFP, and for each, the SFP-relevant security
attributes, or named groups of SFP-relevant security attributes].
[assignment: list of subjects and objects controlled under the indicated SFP, and for each, the SFP-relevant
security attributes, or named groups of SFP-relevant security attributes] ：
＜Subject＞ ＜Subject attributes＞
・task substituted for a user ⇒ ・File attributes（Secure print internal control ID）
・Administrator attributes
----------------------------------------------------------------------------------------------------------------------------------------------
＜Object＞ ＜Object attributes＞
・Secure print file ⇒ ・File attributes（Secure print internal control ID）
[assignment: access control SFP] ：
Secure print file access control
FDP_ACF.1.2[2]
The TSF shall enforce the following rules to determine if an operation among controlled subjects and
controlled objects is allowed: [assignment: rules governing access among controlled subjects and controlled
objects using controlled operations on controlled objects].
[assignment: rules governing access among controlled subjects and controlled objects using controlled
operations on controlled objects] ：
・A task to act for a user who has a file attribute (the secure print internal control ID) is permitted the
print operation to the secure print file that has matched the file attribute (secure print internal control
ID) with the file attribute (secure print internal control ID).
FDP_ACF.1.3[2]
The TSF shall explicitly authorise access of subjects to objects based on the following additional rules:
[assignment: rules, based on security attributes, that explicitly authorise access of subjects to objects].
[assignment: rules, based on security attributes, that explicitly authorise access of subjects to objects] ：
A task to act for a user who has an administrator attribute is permitted to back up secure print file.
FDP_ACF.1.4[2]
The TSF shall explicitly deny access of subjects to objects based on the [assignment: rules, based on security
attributes, that explicitly deny access of subjects to objects].
[assignment: rules, based on security attributes, that explicitly deny access of subjects to objects] ：
None
Hierarchical to ： No other components
Dependencies ： FDP_ACC.1（FDP_ACC.1[2]）
、FMT_MSA.3（FMT_MSA.3）
FDP_ACF.1[3] Security attribute based access control
FDP_ACF.1.1[3]
The TSF shall enforce the [assignment: access control SFP] to objects based on the following: [assignment:
list of subjects and objects controlled under the indicated SFP, and for each, the SFP-relevant security
attributes, or named groups of SFP-relevant security attributes].
[assignment: list of subjects and objects controlled under the indicated SFP, and for each, the
SFP-relevant security attributes, or named groups of SFP-relevant security attributes] ：
＜Subject＞ ＜Subject attributes＞
・Task substituted for a user ⇒ ・Administrator attributes
・CE attributes
----------------------------------------------------------------------------------------------------------------------------------------------
＜Object＞
・HDD Lock Password Object
・Encryption passphrase object
・Printer address group object
[assignment: access control SFP]：
Setting management access control
FDP_ACF.1.2[3]
The TSF shall enforce the following rules to determine if an operation among controlled subjects and
controlled objects is allowed: [assignment: rules governing access among controlled subjects and
controlled objects using controlled operations on controlled objects].
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
25 / 90
[assignment: rules governing access among controlled subjects and controlled objects using controlled
operations on controlled objects] ：
・A task act for a user who has an administrator attribute is permitted to set the HDD lock password
object and the encryption passphrase object, and then to operate the restoration and back-up.
・A task act for a user who has an administrator attribute is permitted to set the printer address group
object, and to operate the restoration.
・A task act for a user who has a CE attribute is permitted to set the HDD lock password object and the
encryption passphrase object.
FDP_ACF.1.3[3]
The TSF shall explicitly authorise access of subjects to objects based on the following additional rules:
[assignment: rules, based on security attributes, that explicitly authorise access of subjects to objects].
[assignment: rules, based on security attributes, that explicitly authorise access of subjects to objects] ：
None
FDP_ACF.1.4[3]
The TSF shall explicitly deny access of subjects to objects based on the [assignment: rules, based on
security attributes that explicitly deny access of subjects to objects].
[assignment: rules, based on security attributes, that explicitly deny access of subjects to objects] ：
None
Hierarchical to ： No other components
Dependencies ： FDP_ACC.1（FDP_ACC.1[3]）
、FMT_MSA.3（N/A）
5.1.1.3. Identification and authentication
FIA_AFL.1[1] Authentication failure handling
FIA_AFL.1.1[1]
The TSF shall detect when [selection: [assignment: positive integer number], an administrator
configurable positive integer within [assignment: range of acceptable values]] unsuccessful
authentication attempts occur related to [assignment: list of authentication events].
[assignment: list of authentication events] ：
・Authentication for accessing the service mode
・Re-authentication for changing the CE password.
[selection: [assignment: positive integer number], an administrator configurable positive integer
within [assignment: range of acceptable values]]
[assignment: range of acceptable values] : an administrator configurable positive integer within 1〜3
FIA_AFL.1.2[1]
When the defined number of unsuccessful authentication attempts has been met or surpassed, the TSF
shall [assignment: list of actions].
[assignment: list of actions]：
＜Action when it is detected＞
・ Log off from the authentication status of the service mode if it is, and lock the authentication
function which uses the CE password.
・ If it’s not under the authentication status, lock the authentication function which uses the CE
password.
＜Operation for recovering the normal condition＞
Perform the boot process of the TOE.
Hierarchical to ： No other components
Dependencies ： FIA_UAU.1（FIA_UAU.2[1]）
FIA_AFL.1[2] Authentication failure handling
FIA_AFL.1.1[2]
The TSF shall detect when [selection: [assignment: positive integer number], an administrator
configurable positive integer within [assignment: range of acceptable values]] unsuccessful
authentication attempts occur related to [assignment: list of authentication events].
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
26 / 90
[assignment: list of authentication events] ：
・Authentication for accessing the administrator mode
・Re-authentication for changing the administrator password
[selection: [assignment: positive integer number], an administrator configurable positive integer
within [assignment: range of acceptable values]]
[assignment: range of acceptable values]：an administrator configurable positive integer within 1〜3
FIA_AFL.1.2[2]
When the defined number of unsuccessful authentication attempts has been met or surpassed, the TSF
shall [assignment: list of actions].
[assignment: list of actions] ：
＜Action when it is detected＞
・ Log off from the authentication status of the administrator mode if it is, and lock the
authentication function which uses the administrator password.
・ If it’s not under the authentication status, lock the authentication function which uses the
administrator password.
＜Operation for recovering the normal condition＞
Perform the boot process of the TOE.
Hierarchical to ： No other components
Dependencies ： FIA_UAU.1（FIA_UAU.2[2]）
FIA_AFL.1[3] Authentication failure handling
FIA_AFL.1.1[3]
The TSF shall detect when [selection: [assignment: positive integer number], an administrator
configurable positive integer within [assignment: range of acceptable values]] unsuccessful
authentication attempts occur related to [assignment: list of authentication events].
[assignment: list of authentication events] ：
Authentication for accessing the MIB object through SNMP
[selection: [assignment: positive integer number], an administrator configurable positive integer
within [assignment: range of acceptable values]]
[assignment: range of acceptable values]：an administrator configurable positive integer within 1〜3
FIA_AFL.1.2[3]
When the defined number of unsuccessful authentication attempts has been met or surpassed, the TSF
shall [assignment: list of actions].
[assignment: list of actions]：
＜Action when it is detected＞
Deny the access to the MIB object and lock the authentication function to use SNMP password.
＜Operation for recovering the normal condition＞
・Perform the lock release function offered within the administrator mode.
・Reboot the TOE.
Hierarchical to ： No other components
Dependencies ： FIA_UAU.1（FIA_UAU.2[2]）
FIA_AFL.1[4] Authentication failure handling
FIA_AFL.1.1[4]
The TSF shall detect when [selection: [assignment: positive integer number], an administrator
configurable positive integer within [assignment: range of acceptable values]] unsuccessful
authentication attempts occur related to [assignment: list of authentication events].
[assignment: list of authentication events]：
Authentication for accessing the secure print file
[selection: [assignment: positive integer number], an administrator configurable positive integer
within [assignment: range of acceptable values]]
[assignment: range of acceptable values]：an administrator configurable positive integer within 1〜3
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
27 / 90
FIA_AFL.1.2[4]
When the defined number of unsuccessful authentication attempts has been met or surpassed, the TSF
shall [assignment: list of actions].
[assignment: list of actions]：
＜Action when it is detected＞
Deny the access to the secure print file and lock the authentication function for the concerned secure
print file.
＜Operation for recovering the normal condition＞
・Perform the lock release function offered within the administrator mode.
・Reboot the TOE.
Hierarchical to ： No other components
Dependencies ： FIA_UAU.1（FIA_UAU.2[3]）
FIA_AFL.1[5] Authentication failure handling
FIA_AFL.1.1[5]
The TSF shall detect when [selection: [assignment: positive integer number], an administrator
configurable positive integer within [assignment: range of acceptable values]] unsuccessful
authentication attempts occur related to [assignment: list of authentication events].
[assignment: list of authentication events].：
Authentication for accessing the user box
[selection: [assignment: positive integer number], an administrator configurable positive integer
within [assignment: range of acceptable values]]
[assignment: range of acceptable values]：an administrator configurable positive integer within 1〜3
FIA_AFL.1.2[5]
When the defined number of unsuccessful authentication attempts has been met or surpassed, the TSF
shall [assignment: list of actions].
[assignment: list of actions]：
＜Action when it is detected＞
Deny the access to the user box and the user box file in the concerned user box and lock the
authentication function for the concerned user box.
＜Operation for recovering the normal condition＞
・ Perform the lock release function offered within the administrator mode.
・ Reboot the TOE.
Hierarchical to ： No other components
Dependencies ： FIA_UAU.1（FIA_UAU.2[4]）
FIA_AFL.1[6] Authentication failure handling
FIA_AFL.1.1[6]
The TSF shall detect when [selection: [assignment: positive integer number], an administrator
configurable positive integer within [assignment: range of acceptable values]] unsuccessful
authentication attempts occur related to [assignment: list of authentication events].
[assignment: list of authentication events]：
･ Authentication when it accesses service mode
･ Authentication when it accesses administrator mode from the panel
･ Authentication when it accesses secure print file
･ Authentication when it accesses user box from the panel
[selection: [assignment: positive integer number], an administrator configurable positive integer
within [assignment: range of acceptable values]]
[assignment: positive integer number] ：1
FIA_AFL.1.2[6]
When the defined number of unsuccessful authentication attempts has been met or surpassed, the TSF
shall [assignment: list of actions].
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
28 / 90
[assignment: list of actions]：
＜Action when it is detected＞
Deny all access from the panel.
＜Operation for recovering the normal condition＞
・ Automatically release the lock after 5 seconds.
Hierarchical to ： No other components
Dependencies ： FIA_UAU.1（FIA_UAU.2[1]、FIA_UAU.2[2]、FIA_UAU.2[3]、FIA_UAU.2[4]
FIA_ATD.1 User attribute definition
FIA_ATD.1.1
The TSF shall maintain the following list of security attributes belonging to individual users:
[assignment: list of security attributes].
[assignment: list of security attributes] ：
・User box attributes（User box ID）
・File attributes（Secure print internal control ID）
Hierarchical to ： No other components
Dependencies ： No dependencies
FIA_SOS.1[1] Verification of secrets
FIA_SOS.1.1[1]
The TSF shall provide a mechanism to verify that secrets (Administrator Password, CE Password)
meet [assignment: a defined quality metric].
[assignment: a defined quality metric]：
・Number of digits: 8- digits
・Character type: ASCII code（0x21 〜 0x7E、except 0x22 and0x2B）
・Rule ：① Do not composed by only the same kind of character strings.
② Do not set the same password as the current setting.
Hierarchical to ： No other components
Dependencies ： No dependencies
FIA_SOS.1[2] Verification of secrets
FIA_SOS.1.1[2]
The TSF shall provide a mechanism to verify that secrets (SNMP Password) meet [assignment: a
defined quality metric].
[assignment: a defined quality metric]：
・Number of digits: 8- digits
・Character type: ASCII code 0x20 〜 0x7E）
Hierarchical to ： No other components
Dependencies ： No dependencies
FIA_SOS.1[3] Verification of secrets
FIA_SOS.1.1[3]
The TSF shall provide a mechanism to verify that secrets (HDD Lock Password, Encryption
passphrase) meet [assignment: a defined quality metric].
[assignment: a defined quality metric]：
・Number of digits: 20- digits
・
Character type: ASCII code
（0x21 〜 0x7E、
except 0x22, 0x28, 0x29, 0x2C, 0x3A, 0x3B, 0x3C, 0x3E,
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
29 / 90
0x5B, 0x5C and 0x5D）
・Rule ： Do not composed by only the same kind of character strings.
.
Hierarchical to ： No other components
Dependencies ： No dependencies
FIA_SOS.1[4] Verification of secrets
FIA_SOS.1.1[4]
The TSF shall provide a mechanism to verify that secrets (Secure print password, User box password)
meet [assignment: a defined quality metric].
[assignment: a defined quality metric]：
・Number of digits: 8- digits
・Character type: ASCII code（0x20 〜 0x7E、except 0x22 and0x2B）
・Rule ： Do not composed by only the same kind of character strings.
Hierarchical to ： No other components
Dependencies ： No dependencies
FIA_SOS.1[5] Verification of secrets
FIA_SOS.1.1[5]
The TSF shall provide a mechanism to verify that secrets (Session Information) meet [assignment: a
defined quality metric].
[assignment: a defined quality metric]：
10 10 and above
Hierarchical to ： No other components
Dependencies ： No dependencies
FIA_SOS.2 TSF Generation of secrets
FIA_SOS.2.1
The TSF shall provide a mechanism to generate secrets (Session information) that meet [assignment: a
defined quality metric.].
[assignment: a defined quality metric.]：
10 10and above
FIA_SOS.2.2
The TSF shall be able to enforce the use of TSF generated secrets for [assignment: list of TSF
functions].
[assignment: list of TSF functions]：
・Administrator authentication（Access through the network）
・User box authentication（Access through the network）
Hierarchical to ： No other components
Dependencies ： No dependencies
FIA_UAU.2[1] User authentication before any action
FIA_UAU.2.1[1]
The TSF shall require each user （Service Engineer） to be successfully authenticated before allowing
any other TSF-mediated actions on behalf of that user （Service Engineer）.
Hierarchical to ： FIA_UAU.1
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
30 / 90
Dependencies ： FIA_UID.1（FIA_UID.2[1]）
FIA_UAU.2[2] User authentication before any action
FIA_UAU.2.1[2]
The TSF shall require each user（Administrator）to be successfully authenticated before allowing any
other TSF-mediated actions on behalf of that user （Administrator）.
Hierarchical to ： FIA_UAU.1
Dependencies ： FIA_UID.1（FIA_UID.2[2]）
FIA_UAU.2[3] User authentication before any action
FIA_UAU.2.1[3]
The TSF shall require each user （User who is permitted to use secure print file） to be successfully
authenticated before allowing any other TSF-mediated actions on behalf of that user （User who is
permitted to use secure print file）
Hierarchical to ： FIA_UAU.1
Dependencies ： FIA_UID.1（FIA_UID.2[3]）
FIA_UAU.2[4] User authentication before any action
FIA_UAU.2.1[4]
The TSF shall require each user （User who is permitted to use the user box） to be successfully
authenticated before allowing any other TSF-mediated actions on behalf of that user （User who is
permitted to use the user box）
Hierarchical to ： FIA_UAU.1
Dependencies ： FIA_UID.1（FIA_UID.2[4]）
FIA_UAU.6 Re-authenticating
FIA_UAU.6.1
The TSF shall re-authenticate the use under the conditions [assignment: list of conditions under which
re-authentication is required].
[assignment: list of conditions under which re-authentication is required]
・When the administrator modifies the administrator password.
・When the service engineer modifies the CE password.
・When the administrator changes the HDD lock setting.
・When the administrator changes the Encryption function setting.
Hierarchical to ： No other components
Dependencies ： No dependencies
FIA_UAU.7 Protected authentication feedback
FIA_UAU.7.1
The TSF shall provide only [assignment: list of feedback] to the user while the authentication is in
progress.
[assignment: list of feedback]：
Display “*" every character data input.
Hierarchical to ： No other components
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
31 / 90
Dependencies ： FIA_UAU.1（FIA_UAU.2[1]、FIA_UAU.2[2]、FIA_UAU.2[3]、FIA_UAU.2[4]
FIA_UID.2[1] User identification before any action
FIA_UID.2.1[1]
The TSF shall require each user （Service Engineer）to identify itself before allowing any other
TSF-mediated actions on behalf of that user（Service Engineer）.
Hierarchical to ： FIA_UID.1
Dependencies ： No dependencies
FIA_UID.2[2] User identification before any action
FIA_UID.2.1[2]
The TSF shall require each user （Administrator）to identify itself before allowing any other
TSF-mediated actions on behalf of that user（Administrator）.
Hierarchical to ： FIA_UID.1
Dependencies ： No dependencies
FIA_UID.2[3] User identification before any action
FIA_UID.2.1[3]
The TSF shall require each user（User who is permitted to use secure print file）
to identify itself before
allowing any other TSF-mediated actions on behalf of that user（User who is permitted to use secure
print file）.
Hierarchical to ： FIA_UID.1
Dependencies ： No dependencies
FIA_UID.2[4] User identification before any action
FIA_UID.2.1[4]
The TSF shall require each user （User who is permitted to use the user box）to identify itself before
allowing any other TSF-mediated actions on behalf of that user（User who is permitted to use the user
box）.
Hierarchical to ： FIA_UID.1
Dependencies ： No dependencies
FIA_USB.1 User-subject binding
FIA_USB.1.1
The TSF shall associate the following user security attributes with subjects acting on the behalf of that
user: [assignment; list of user security attributes].
[assignment; list of user security attributes]:
・User box attributes (User Box ID)
・File attributes (Secure print internal control ID)
FIA_USB.1.2
The TSF shall enforce the following rules on the initial association of user security attributes with
subjects acting on the behalf of users: [assignment: rules for the initial association of attributes].
[assignment: rules for the initial association of attributes]:
・For user box attributes, user box ID of the concerned user box associates to the task acting on the
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
32 / 90
behalf of users when authenticated with the access to the user box
・For file attributes, the secure print internal control ID of the concerned secure print file associates
to the task acting on the behalf of users when authenticated with the access to the secure print file.
FIA_USB.1.3
The TSF shall enforce the following rules governing changes to the user security attributes associated
with subjects acting on the behalf of users: [assignment: rules for the changing of attributes].
[assignment: rules for the changing of attributes].
None
Hierarchical to ： No other components
Dependencies ： FIA_ATD.1
5.1.1.4. Security management
FMT_MOF.1[1] Management of security functions behaviour
FMT_MOF.1.1[1]
The TSF shall restrict the ability to [selection: determine the behaviour of, disable, enable, modify the
behaviour of] the functions [assignment: list of functions] to [assignment: the authorised identified
roles].
[assignment: list of functions] ：
・Enhanced Security Setting
[selection: determine the behaviour of, disable, enable, modify the behaviour of] ：
disable
[assignment: the authorised identified roles] ：
・Administrator
・Service Engineer
Hierarchical to ： No other components
Dependencies ： FMT_SMF.1（FMT_SMF.1）
、FMT_SMR.1（FMT_SMR.1[1]、FMT_SMR.1[2]）
FMT_MOF.1[2] Management of security functions behaviour
FMT_MOF.1.1[2]
The TSF shall restrict the ability to [selection: determine the behaviour of, disable, enable, modify the
behaviour of] the functions [assignment: list of functions] to [assignment: the authorised identified
roles].
[assignment: list of functions]：
・SNMP password authentication function
[selection: determine the behaviour of, disable, enable, modify the behaviour of] ：
modify the behaviour of
[assignment: the authorised identified roles] ：
Administrator
Hierarchical to ： No other components
Dependencies ： FMT_SMF.1（FMT_SMF.1）
、FMT_SMR.1（FMT_SMR.1[2]）
FMT_MOF.1[3] Management of security functions behaviour
FMT_MOF.1.1[3]
The TSF shall restrict the ability to [selection: determine the behaviour of, disable, enable, modify the
behaviour of] the functions [assignment: list of functions] to [assignment: the authorised identified
roles].
[assignment: list of functions]：
・Setup function
[selection: determine the behaviour of, disable, enable, modify the behaviour of] ：
enable
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
33 / 90
[assignment: the authorised identified roles] ：
Service engineer
Hierarchical to ： No other components
Dependencies ： FMT_SMF.1（FMT_SMF.1）
、FMT_SMR.1（FMT_SMR.1[1]）
FMT_MSA.3 Static attribute initialization
FMT_MSA.3.1
The TSF shall enforce the [assignment: access control SFP, information flow control SFP] to provide
[selection, choose one of: restrictive, permissive, [assignment: other property]] default values for
security attributes (Secure print internal control ID) that are used to enforce the SFP.
[selection, choose one of: restrictive, permissive, [assignment: other property]]：
[assignment: other property]：Identified uniquely
[assignment: access control SFP, information flow control SFP]：
Secure print file access control
FMT_MSA.3.2
The TSF shall allow the [assignment: the authorized identified roles] to specify alternative initial
values to override the default values when an object or information is created.
[assignment: the authorized identified roles]
None
Hierarchical to ： No other components
Dependencies ： FMT_MSA.1（N/A）
、FMT_SMR.1（N/A）
FMT_MTD.1[1] Management of TSF data
FMT_MTD.1.1[1]
The TSF shall restrict the ability to [selection: change_default, query, modify, delete, clear, [assignment:
other operations]] the [assignment: list of TSF data] to [assignment: the authorised identified roles].
[assignment: list of TSF data]：
・SNMP password
・Secure print password
・Threshold Number of authentication failure
[selection: change_default, query, modify, delete, clear, [assignment: other operations]]：
modify
[assignment: the authorised identified roles]：
Administrator
Hierarchical to ： No other components
Dependencies ： FMT_SMF.1（FMT_SMF.1）、FMT_SMR.1（FMT_SMR.1[2]）
FMT_MTD.1[2] Management of TSF data
FMT_MTD.1.1[2]
The TSF shall restrict the ability to [selection: change_default, query, modify, delete, clear, [assignment:
other operations]] the [assignment: list of TSF data] to [assignment: the authorised identified roles].
[assignment: list of TSF data]：
User box password of the relevant user box
[selection: change_default, query, modify, delete, clear, [assignment: other operations]]：
modify
[assignment: the authorised identified roles]：
・User who is permitted to use that user box
・Administrator
Hierarchical to ： No other components
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
34 / 90
Dependencies ： FMT_SMF.1（FMT_SMF.1）
、FMT_SMR.1（FMT_SMR.1[2]、FMT_SMR.1[3]）
FMT_MTD.1[3] Management of TSF data
FMT_MTD.1.1[3]
The TSF shall restrict the ability to [selection: change_default, query, modify, delete, clear,
[assignment: other operations]] the [assignment: list of TSF data] to [assignment: the authorised
identified roles].
[assignment: list of TSF data]：
・Administrator password
[selection: change_default, query, modify, delete, clear, [assignment: other operations]]：
modify
[assignment: the authorised identified roles]：
・Administrator
・Service Engineer
Hierarchical to ： No other components
Dependencies ： FMT_SMF.1（FMT_SMF.1）
、FMT_SMR.1（FMT_SMR.1[1]、FMT_SMR.1[2]）
FMT_MTD.1[4] Management of TSF data
FMT_MTD.1.1[4]
The TSF shall restrict the ability to [selection: change_default, query, modify, delete, clear,
[assignment: other operations]] the [assignment: list of TSF data] to [assignment: the authorised
identified roles].
[assignment: list of TSF data]：
・SNMP password
・User box password
・Secure print password
[selection: change_default, query, modify, delete, clear, [assignment: other operations]]：
query
[assignment: the authorised identified roles]：
・Administrator
Hierarchical to ： No other components
Dependencies ： FMT_SMF.1（FMT_SMF.1）、FMT_SMR.1（FMT_SMR.1[2]）
FMT_MTD.1[5] Management of TSF data
FMT_MTD.1.1[5]
The TSF shall restrict the ability to [selection: change_default, query, modify, delete, clear,
[assignment: other operations]] the [assignment: list of TSF data] to [assignment: the authorised
identified roles].
[assignment: list of TSF data]：
CE password
[selection: change_default, query, modify, delete, clear, [assignment: other operations]]：
modify
[assignment: the authorised identified roles]：
Service Engineer
Hierarchical to ： No other components
Dependencies ： FMT_SMF.1（FMT_SMF.1）、FMT_SMR.1（FMT_SMR.1[1]）
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
35 / 90
FMT_MTD.1[6] Management of TSF data
FMT_MTD.1.1[6]
The TSF shall restrict the ability to [selection: change_default, query, modify, delete, clear, [assignment:
other operations]] the [assignment: list of TSF data] to [assignment: the authorised identified roles].
[assignment: list of TSF data]：
Administrator password, SNMP password
[selection: change_default, query, modify, delete, clear, [assignment: other operations]]：
[assignment: other operations]：Initialization
[assignment: the authorised identified roles]：
Administrator, Service Engineer
Hierarchical to ： No other components
Dependencies ： FMT_SMF.1（FMT_SMF.1）、FMT_SMR.1（FMT_SMR.1[1]、FMT_SMR.1[2]）
FMT_SMF.1 Specification of Management Functions
FMT_SMF.1.1
The TSF shall be capable of performing the following security management functions: [assignment: list
of security management functions to be provided by the TSF].
[assignment: list of security management functions to be provided by the TSF]：
・Stop Function of Enhanced security function by administrator
・Operation Setting Function of SNMP password authentication function by administrator
・Setting function of authentication failure frequency threshold by administrator in the
authentication operation prohibition function
・Backup Function by administrator 2
・Restoration Function by administrator 3
・Deletion Function of detected value of unauthorized access to SNMP by administrator
・Deletion function of detected value of unauthorized access to secure print by administrator
・Deletion function of detected value of unauthorized access to user box by administrator
・Modification function of administrator password by administrator
・Modification function of SNMP password by administrator
・Modification function of user box password by administrator
・Initialization function of administrator password by administrator
・Initialization function of SNMP password by administrator
・Modification function of CE password by service engineer
・Modification function of administrator password by service engineer
・Start function of Setup function by service engineer
・Stop function of Enhanced Security function by service engineer
・Initialization function of administrator password by service engineer
・Initialization function of SNMP password by service engineer
･Modification function of user box password of the user box by user who is permitted the use of
public user box
Hierarchical to ： No other components
Dependencies ： No dependencies
FMT_SMR.1[1] Security roles
FMT_SMR.1.1[1]
The TSF shall maintain the roles [assignment: the authorised identified roles].
[assignment: the authorised identified roles] ：
Service Engineer
2
A part of a backup function corresponds to the inquiry function of TSF data.
3
A part of the restoration function corresponds to the modification function of the TSF data.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
36 / 90
FMT_SMR.1.2[1]
The TSF shall be able to associate users with roles.
Hierarchical to ： No other components
Dependencies ： FIA_UID.1（FIA_UID.2[1]）
FMT_SMR.1[2] Security roles
FMT_SMR.1.1[2]
The TSF shall maintain the roles [assignment: the authorised identified roles].
[assignment: the authorised identified roles] ：
Administrator
FMT_SMR.1.2[2]
The TSF shall be able to associate users with roles.
Hierarchical to ： No other components
Dependencies ： FIA_UID.1（FIA_UID.2[2]）
FMT_SMR.1[3] Security roles
FMT_SMR.1.1[3]
The TSF shall maintain the roles [assignment: the authorised identified roles].
[assignment: the authorised identified roles]：
User who is authorized to use that user box
FMT_SMR.1.2[4]
The TSF shall be able to associate users with roles.
Hierarchical to ： No other components
Dependencies ： FIA_UID.1（FIA_UID.2[4]）
5.1.1.5. Protection of the TSF
FPT_RVM.1 Non-bypassability of the TSP
FPT_RVM.1.1
The TSF shall ensure that TSP enforcement functions are invoked and succeed before each function
within the TSC is allowed to proceed.
Hierarchical to ： No other components
Dependencies ： No dependencies
FPT_SEP.1 TSF domain separation
FPT_SEP.1.1
The TSF shall maintain a security domain for its own execution that protects it from interference and
tampering by untrusted subjects.
FPT_SEP.1.2
The TSF shall enforce separation between the security domains of subjects in the TSC.
Hierarchical to ： No other components
Dependencies ： No dependencies
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
37 / 90
5.1.1.6. Extended requirement: Identification and approval of access destination
FIA_NEW.1
Identification and approval of a user becoming an access object
from TOE
FIA_NEW.1.1
TSF shall demand to succeed in the user's identification before the action is taken to user (HDD) by
TOE.
FIA_NEW.1.2
TSF shall stop the start of the action to user (HDD) by TOE if the user's identification is failed.
Hierarchical to ： No other components
Dependencies ： No dependencies
Audit：FIA_NEW.1
The following actions should be auditable if FAU_GEN Security audit data generation is included in the
PP/ST.
a) Minimal unsuccessful use of user identification mechanism including offered user identification
information
b) Basic Use all of user identification mechanism including offered user deification
information
Management：FIA_NEW.1
The following actions could be considered for the management functions in FMT.
a) management of user identification information
5.1.1.7. Extended requirement: Remaining information protection after the explicit deletion operation
FNEW_RIP.1
Protection of remaining information on the user data and TSF data
after explicit deletion operation
FNEW_RIP.1.1
TSF shall ensure that each previous information contents assigned to the resource is made
unavailable by the explicit deletion of the following objects and TSF data.: [assignment: list of object
and list of TSF data].
[assignment : List of object and list of TSF data]：
＜Objects＞
・User Box file
・Secure print file
・On memory image file
・Stored image file
・Remaining image file
・Image-related file
・HDD lock password object
・Encryption passphrase object
＜TSF data＞
・Administrator password
・SNMP password
・User Box password
・Secure print password
・Remaining TSF data4
Hierarchical to ： No other components
Dependencies ： No dependencies
4
TSF data remaining in the HDD data area, that cannot be deleted only by the deletion of the file
management area.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
38 / 90
Audit：FNEW_RIP.1
Use including the information of user identification performing the explicit deletion operation.
Management：FNEW_RIP.1
There is no foreseen management activity.
5.1.2. Minimum Security Strength of Function
The minimum strength of function level of the TOE is SOF-Basic. The required TOE security
functions that use a probabilistic/permutational mechanism are FIA_UAU.2[1], FIA_UAU.2[2],
FIA_UAU.2[3], FIA_UAU.2[4], FIA_UAU.6, FIA_SOS.1[1], FIA_SOS.1[2], FIA_SOS.1[3],
FIA_SOS.1[4], FIA_SOS.1[5] and FIA_SOS.2.
Encryption key generation algorithm of FMT_CKM.1 is not included in the object of the
minimum strength of function level.
5.1.3. TOE Security Assurance Requirements
The TOE is a commercial office product that is used in a general office environment, and
therefore a TOE security assurance requirement that is required for EAL3 conformance, which
is a sufficient level as an assurance for commercial office products, is applied. The following table
summarizes the applied TOE security assurance requirements.
Table 4 TOE Security Assurance Requirements
TOE Security Assurance Requirements Component
CM capabilities ACM_CAP.3
Class ACM:
Configuration management CM scope ACM_SCP.1
Delivery ADO_DEL.1
Class ADO:
Delivery and Operation Installation, generation and start-up ADO_IGS.1
Function specification ADV_FSP.1
High-level design ADV_HLD.2
Class ADV:
Development
Representation correspondence ADV_RCR.1
Administrator guidance AGD_ADM.1
Class AGD:
Guidance Documents User guidance AGD_USR.1
Class ALC:
Life Cycle Support
Development security ALC_DVS.1
Coverage ATE_COV.2
Depth ATE_DPT.1
Functional tests ATE_FUN.1
Class ATE:
Tests
Independent testing ATE_IND.2
Misuse AVA_MSU.1
Strength of TOE security functions AVA_SOF.1
Class AVA:
Vulnerability Assessment
Vulnerability analysis AVA_VLA.1
5.2. Security Requirements for the IT environment
5.2.1.1. Cryptographic support
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
39 / 90
FCS_COP.1[E] Cryptographic operation
FCS_COP.1.1[E]
The TSF
（Encryption board）
、
shall perform [assignment: list of cryptographic operations] in accordance
with a specified cryptographic algorithm [assignment: cryptographic algorithm] and cryptographic key
sizes [assignment: cryptographic key sizes] that meet the following: [assignment: list of standards].
[assignment: list of standards]：
FIPS PUB 197
[assignment: cryptographic algorithm]：
AES
[assignment: cryptographic key sizes]：
128bit
[assignment: list of cryptographic operations]：
・Encryption of all data written in HDD
・Decryption of all data read from HDD
Hierarchical to ： No other components
Dependencies ： FDP_ITC.1 or FCS_CKM.1（FCS_CKM.1）
、FCS_CKM.4（N/A）
、
FMT_MSA.2（N/A）
5.2.1.2. Identification and Authentication
FIA_AFL.1[E] Authentication failure handling
FIA_AFL.1.1[E]
The TSF（HDD）shall detect when [selection: [assignment: positive integer number], an administrator
configurable positive integer within [assignment: range of acceptable values]] unsuccessful
authentication attempts occur related to [assignment: list of authentication events].
[assignment: list of authentication events] ：
Authentication by HDD Lock function at the time of accessing HDD
[selection: [assignment: positive integer number], an administrator configurable positive integer
within [assignment: range of acceptable values]]
[assignment: positive integer number] ：5
FIA_AFL.1.2[E]
When the defined number of unsuccessful authentication attempts has been met or surpassed, the TSF
shall [assignment: list of actions].
[assignment: list of actions]：
＜Action when it is detected＞
Deny the reading and writing of data to HDD.
＜Operation for recovering the normal condition＞
Turn off electricity to HDD（Power OFF）
Hierarchical to ： No other components
Dependencies ： FIA_UAU.1（FIA_UAU.2[E]）
FIA_UAU.2[E] User authentication before any action
FIA_UAU.2.1[E]
The TSF（HDD） shall require each user （The main body of Printer where HDD installed） to be
successfully authenticated before allowing any other TSF-mediated actions on behalf of that user（The
main body of Printer where HDD installed）.
Hierarchical to ： FIA_UAU.1
Dependencies ： FIA_UID.1（N/A）
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
40 / 90
FIA_UAU.7[E] Protected authentication feedback
FIA_UAU.7.1[E]
The TSF（PC application） shall provide only [assignment: list of feedback] to the user while the
authentication is in progress.
[assignment: list of feedback] ：
display "*" in every character data input
Hierarchical to ： No other components
Dependencies ： FIA_UAU.1（FIA_UAU.2[2]、FIA_UAU.2[4]）
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
41 / 90
6. TOE Summary Specification
6.1. TOE Security Functions
The list of the TOE security function led from the TOE security function requirement is shown
in the following Tables 5. The detailed specification is explained in the paragraphs described
below.
Table 5: The list of the name and identifier of TOE Security function
No. TOE Security Function
1 F.ADMIN Administrator function
2 F.ADMIN-SNMP SNMP administrator function
3 F.SERVICE Service mode function
4 F.USER User function
5 F.BOX User box function
6 F.PRINT Secure print function
7 F.OVERWRITE-ALL Overwrite all area function
8 F.CRYPT Encryption key generation function
9 F.HDD HDD validation function
10 F.RESET Authentication Failure Reset function
6.1.1. F.ADMIN（Administrator Function）
F.ADMIN is a series of security function that administrator operates, such as an administrator
identification authentication function in an administrator mode accessing from a panel or
through a network, and a security management function that includes a change of an
administrator password and a lock cancellation of a locked user box. (Nevertheless, all functions
are not feasible functions through both a panel and a network.)
6.1.1.1. Administrator identification authentication function
It identifies and authenticates the accessing user as the administrator in response to the
access request to the administrator mode.
Offers the administrator authentication mechanism authenticating by the administrator
password that consists of the character shown in Table 6.
Offers the administrator authentication mechanism using the session information besides
the administrator password, after the administrator is authenticated to the access from
the network,
According to protocol, use the session information of more than 1010, or generate and use
the session information more than 1010.
Return “*" for each character as feedback for the entered administrator password.
Resets the number of authentication failure when succeeding in the authentication.
In the case of access from a panel, it doesn't accept the input from a panel for five seconds
when failing in the authentication.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
42 / 90
Locks all the authentication functions to use the administrator password when detecting the
authentication failure that becomes 1〜3 times at total in each authentication function by
using the administrator password. (Refuse the access to the administrator mode)
The administrator specifies the failure frequency threshold by the unauthorized access
detected threshold setting function.
Lock of Authentication function is released with F.RESET function operated.
Table 6 Character and number of digits used for password
Objectives Number
of digits
Characters
CE Password
Administrator Password
8-digits 92 characters in total can be selected
ASCII code（0x21 - 0x7E, except 0x22 and 0x2B）
・Number：0 - 9
・Alphabet：Capital letter and small letter
・Symbols：!, #, $, %, &, ' , (, ), *, , , - , . , / , : , ; , <, =, >, ?, @,
[ , ¥ , ] , ^ , _ , ` , { , | , } , ~
User Box Password
Secure Print Password
8-digits 93 characters in total can be selected
ASCII code（0x20 - 0x7E, except 0x22 and 0x2B）
・Number：0 - 9
・Alphabets：Capital letter and small letter
・Symbols：! , # , $ , % , & , ' , ( , ) , * , , , - , . , / , : , ; , < , = , > , ? ,
@ , [ , ¥ , ] , ^ , _ , ` , { , | , } , ~ , SPACE
HDD Lock Password
Encryption passphrase
20-digits 83 characters in total can be selected
ASCII code（0x21-0x7E, except 0x22, 0x28, 0x29, 0x2C, 0x3A,
0x3B, 0x3C, 0x3E, 0x5B, 0x5C and 0x5D）
・Number：0 - 9
・ Alphabets：Capital letter and small letter
・ Symbols：! , # , $ , % , & , , * , + , - , . , / ,
=, ?, @, ^, _ , ` , { , | , } , ~
SNMP Password
・Privacy Password
・Authentication Password
More
than
8-digits
95 characters in total can be selected
ASCII code（0x20 - 0x7E）
・Number：0 - 9
・Alphabets：Capital letter and small letter
・Symbols：! , # , $ , % , & , ' , ( , ) , * , , , - , . , / , : , ; , < , = , > , ? ,
@ , [ , ¥ , ] , ^ , _ , ` , { , | , } , ~ , ” , + , SPACE
6.1.1.2. Function offered in Administrator mode
When a user is identified and authenticated as an administrator by the administrator
identification authentication function at the accessing request to the administrator mode, the
administrator authority is associated with the task substituting the user. And the following
operations and the use of the functions are permitted.
① Change of Administrator password
When a user is re-authenticated as an administrator and the new password satisfies the
quality, the password is changed.
Offers the administrator password authentication mechanism that is authenticated by the
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
43 / 90
administrator password which consists of the character shown in Table 6.
Resets the number of authentication failure when succeeding in the re-authentication.
Return “*" for each character as feedback for the entered administrator password in the
re-authentication by the access from the panel.
When the authentication failure that becomes 1-3 times at total in each authentication
function by using the administrator password is detected, it logoffs the administrator mode
accessing from the panel, and locks all the authentication functions to use the
administrator password. (The access to the administrator mode is refused.)
The administrator specifies the failure frequency threshold by the unauthorized access
detection threshold setting function.
Lock of Authentication function is released with F.RESET function operated.
Verify the new administrator password if the following qualities are satisfied.
It is composed of the characters and by the number of digits, shown in the Table 6.
It shall not be composed of one kind of character.
It doesn't match with the current value.
② User Box Settings
User Box Registration
・ Set the user box password to the selected unregistered user box ID and register the user
box.
・ It verifies whether the user box password newly set have been satisfied the following
qualities.
It is composed of the characters and by the number of digits, shown in the Table 6.
It shall not be composed of one kind of character.
Change of User Box Password
・ The user box password set to the public user box is changed.
・ It verifies whether the user box password newly set have been satisfied the following
qualities.
It is composed of the characters and by the number of digits, shown in the Table 6.
It shall not be composed of one kind of character.
③ Release of Lock
Reset (0 clear) the number of authentication failure for all users.
If there is a secure print to which access is locked, the lock is released.
Reset (0 clear) the number of authentication failure of all user boxes.
If there is a user box to which access is locked, the lock is released.
Reset (0 clear) the number of authentication failure of SNMP password.
If there is a MIB object to which access is locked, the lock is released.
④ Setting of unauthorized access detection threshold
The unauthorized access detection threshold in the authentication operation prohibition
function is set for 1-3 times.
⑤ Setting and execution of all area overwrite deletion function
The deletion method shown in the following table is selected first, and then the overwrite
deletion at the data area of an HDD is performed. (Perform F.OVERWRITE-ALL.)
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
44 / 90
Table 7 A type of overwrite deletion of all area and the method of overwriting
Method Overwritten data type and their order
Mode:1 0x00
Mode:2 Random numbers ⇒ Random numbers ⇒ 0x00
Mode:3 0x00 ⇒ 0xFF ⇒Random numbers ⇒Verification
Mode:4 Random numbers ⇒ 0x00 ⇒ 0xFF
Mode:5 0x00 ⇒ 0xFF ⇒ 0x00 ⇒ 0xFF
Mode:6 0x00 ⇒ 0xFF ⇒ 0x00 ⇒ 0xFF ⇒ 0x00 ⇒ 0xFF ⇒Random numbers
Mode:7 0x00 ⇒ 0xFF ⇒ 0x00 ⇒ 0xFF ⇒ 0x00 ⇒ 0xFF ⇒ 0xAA
Mode:8 0x00 ⇒ 0xFF ⇒ 0x00 ⇒ 0xFF ⇒ 0x00 ⇒ 0xFF ⇒ 0xAA ⇒
Verification
⑥ Network Settings
A setup operation of the following setting data is performed.
A series of setup data that relates to The printer address（IP address, NetBIOS Name,
AppleTalk Printer Name, etc.）
⑦ Execution of back-up and restoration function
All the setting data stored in an NVRAM and an HDD is backed-up and re-stored except the
administrator password and the CE password.（possible to set by a unit of medium）As the
object related to security, due to the relation of confidentiality and completeness, the one
shown by the following classifications is targeted.
＜Type A : Object to which back-up and restoration should be limited＞
HDD lock password
Encryption passphrase
SNMP password
Secure print password
User Box password
＜Type B : Object to which restoration should be limited＞
A series of data that relates to the Printer address setting
Setting data of Enhanced Security function
Authentication failure frequency threshold of authentication operation prohibition
function
＜Type C : Object to which back-up should be limited＞
Secure print file
User box file
⑧ Operation setting function of HDD lock function
＜Operation Setting ON＞
When turning it ON from OFF, it verifies that the newly set HDD lock password satisfies the
following qualities.
It is composed of the characters and by the number of digits shown in Table 6.
It shall not be composed of one kind of character.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
45 / 90
＜Modification of HDD lock password＞
Change the HDD lock password. By using the HDD lock password currently set, when it is
re-authenticated as an administrator, and the new password satisfies the quality, it is
changed.
Offers the HDD lock password verification mechanism that verified the HDD lock
password that consists of the character shown in Table 6.
Return, in verification, “*" for each character as feedback for the entered HDD lock
password.
Verify the HDD lock password newly set if the following qualities are satisfied.
・It is composed of the characters and by the number of digits shown in Table 6.
・It shall not be composed of one kind of character.
⑨ Operation setting of encryption function
When an optional encryption board is installed to The printer, it can be operated.
＜Operation Setting ON＞
When turning it ON from OFF, it verifies that the encryption passphrase newly set satisfies
the following qualities, and F.CRYPT is performed.
It is composed of the characters and by the number of digits shown in Table 6.
It shall not be composed of one kind of character.
＜Encryption Passphrase Change＞
Change the encryption passphrase. By using the encryption passphrase currently set, when it
is re-authenticated as an administrator, and the new encryption passphrase satisfies the
quality, F.CRYPT is performed.
Offers the encryption passphrase verification mechanism that verified the encryption
passphrase that consists of the character shown in Table 6.
Return, in verification, “*" for each character as feedback for the entered encryption
passphrase.
Verify the encryption passphrase newly set if the following qualities are satisfied.
・It is composed of the characters and by the number of digits shown in Table 6.
・It shall not be composed of one kind of character.
⑩ Function related to Enhanced Security function
The function that influences the setting of the Enhanced Security function that the
administrator operates is as follows. (* It has explained the influence of the backup and
restoration function in ⑦.)
Operation setting of Enhanced Security function
Function to set valid or invalid of Enhanced Security function.
HDD logical format function
Function to re-write system file of OS in HDD. Along with the execution of this logical
format, the setting of the Enhanced Security function is invalidated.
Overwrite deletion function for all area
The settings of enhanced security function are invalidated by executing the overwrite
deletion of all area
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
46 / 90
⑪ Change of SNMP password
The SNMP password (Privacy password and Authentication password) is changed. Verify that
the SNMP password newly set satisfies the following qualities.
It is composed of the characters and by the number of digits shown in Table 6.
⑫ Setting of SNMP password authentication function
The authentication method in the SNMP password authentication function is set to "Only
Authentication password" or the "Authentication password and Privacy password".
6.1.2. F.ADMIN-SNMP（SNMP administrator function）
F.ADMIN-SNMP is a security function, which identifies and authenticates the administrator
in the access through the network by using SNMP from PC, and then permits the operation of a
setting function of the network only to the administrator whose identification and authentication
was succeeded.
6.1.2.1. Identification and authentication function by SNMP password
It identifies and authenticates by the SNMP password, that the user who accesses the MIB
object through the network with the use of SNMP is an administrator
Offers the SNMP authentication mechanism which authenticates by the SNMP password that
consists of the character shown in chart 6.
Only Authentication password or both the Privacy password and the Authentication
password is used.
In the case of SNMP, the SNMP password is used for every session without requiring the
administrator authentication mechanism by the separate session information.
Reset the authentication failure frequency if it succeeds in authentication.
In the case of both the Privacy password and the Authentication password are used, the
authentication failure frequency is reset only when both passwords together succeeded in
the authentication.
When the authentication failure that becomes the 1-3 times at total in each authentication
function by using the SNMP password is detected, all the authentication functions to use the
SNMP password are locked.（The access to the MIB object is refused.）
The administrator specifies the failure frequency threshold by the unauthorized access
detection threshold setting function.
In the case of both the Privacy password and the Authentication password are utilized,
even though both passwords together fails in authentication, it is detected as one failure.
To release the lock, the lock release function to the MIB object of F.ADMIN is performed or the
F.RESET function operates.
6.1.2.2. Management function using SNMP
When it is identified and authenticated that the user is an administrator by the SNMP
password, the access to the MIB object is permitted, and then the operation of the setting data
shown as followings is permitted to be done.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
47 / 90
① Network Settings
Setting operation of the following setting data is performed.
A series of setting data that relates to The printer address（IP address, NetBIOS name,
AppleTalk printer name, etc.）
② Change of SNMP password
The SNMP password (Privacy password and Authentication password) is changed. Verify that
the SNMP password newly set satisfies the following qualities.
It is composed of the characters and by the number of digits shown in Table 6.
③ Setting of SNMP password authentication function
The authentication method in the SNMP password authentication function is set to the
"Authentication password only" or the "Privacy password and the Authentication password".
6.1.3. F.SERVICE（Service mode function）
F.SERVICE is a series of security function that the service engineer operates, such as the
service engineer identification authentication function in service mode accessing from a panel,
and a security management function that includes a change in the CE password and the
administrator password.
6.1.3.1. Service engineer identification authentication function
It is identified and authenticated the accessing user as the service engineer in response to the
access request to the service mode from the panel.
Offers the CE authentication mechanism that is authenticated by the CE password that
consists of the character shown in Table 6.
The CE authentication mechanism by the separate session information is not required
because the service mode can only be accessed from the panel.
Return “*" for each character as feedback for the entered CE password.
Resets the number of the authentication failure when succeeding in the authentication.
Not accept the input from the panel for five seconds when the authentication failed.
When the authentication failure that becomes 1-3 times at total in each authentication
function by using the CE password is detected, it locks all the authentication functions to use
the CE password. (The access to the service mode is refused.)
The administrator specifies the failure frequency threshold by the unauthorized access
detection threshold setting function.
Lock of authentication function is released with F.RESET function operated.
6.1.3.2. Function offered in service mode
When a user is identified and authenticated as a service engineer by the service engineer
identification authentication function at the access request to the service mode, the use of the
following functions is permitted.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
48 / 90
① Change of CE password
When a user is re-authenticated as a service engineer and the new password satisfies the
quality, it is changed.
Offers the CE authentication mechanism that is re-authenticated by the CE password that
consists of the characters shown in Table 6.
Resets the number of authentication failure when succeeding in the re-authentication.
Return “*" for each character as feedback for the entered service codes in the
re-authentication.
When the authentication failure that becomes 1-3 times at total in each authentication
function by using the CE password is detected, it logoffs the service mode accessing from
the panel, and locks all the authentication functions to use the CE password. (The access to
the service mode is refused.)
・ The administrator specifies the failure frequency threshold by the unauthorized access
detection threshold setting function.
The F.RESET function operates to release the lock of the authentication function.
It verifies that the CE password newly set satisfies the following qualities.
・ It is composed of the characters and by the number of digits, shown in the Table 6.
・ It shall not be composed of one kind of character.
・ It shall not be matched with the current value.
② Change of administrator password
Change the administrator password. Verify that the administrator password newly set
satisfies the following qualities.
It is composed of the characters and by the number of digits, shown in the Table 6.
It shall not be composed of one kind of character.
It shall not be matched with the current value.
③ Function that relates to Enhanced Security function
The functions that influence the setting of the Enhanced Security function that the service
engineer operates are as follows.
HDD logical format function
Function to re-write system file of OS in HDD. The setting of the Enhanced Security
function is invalidated along with the execution of this logical format.
HDD physical format function
A function to rewrite the entire disk in HDD with a regulated pattern including the signal
rows such as the track and sector information. The setting of the Enhanced Security
function is invalidated along with the execution of this physical format.
HDD installation setting function
Function to make the installed HDD effective. The setting of the Enhanced Security
function is invalidated by nullifying this HDD installation setting.
Initialization function
Function to reset every setting value written in NVRAM to the factory default. The setting
of the Enhanced Security function is invalidated by executing this initialization function.
④ Function that sets the operation of setup function
Set whether or not to use (operate) the setup function.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
49 / 90
⑤ Function that relates to password initialization function
The function that relates to the initialization of the password that the service engineer
operates is as follows.
Initialization function
Function to reset various setting values written in NVRAM to the factory default. The
administrator password and the SNMP password are set to an initial value of the factory
shipment by executing this initialization function. Both of the operation settings of the
HDD lock function and the encryption function are turned OFF. (The HDD lock password
and the encryption passphrase have been set cannot be used again by turning OFF the
setting operation.)
HDD physical format function
A function to rewrite the entire disk to a regulated pattern in HDD including the signal
rows such as the track and sector information. The HDD lock function is turned OFF along
with the execution of this physical format. (The HDD lock password that is set cannot be
used again by turning OFF the operation setting.)
6.1.4. F.BOX（User Box Function）
F.BOX is a series of security function related to the user box, such as the access control
function to permit various operations of the concerned user box and the user box file after the
user is identified and authenticated that you are the registered user in the access to the user box
6.1.4.1. Registration of user box
Register the user box by setting the user box password to the selected unregistered user box
ID.
Verify that a user box password registered satisfies the following conditions.
It is composed of the characters and by the number of digits, shown in the Table 6.
It shall not be composed of one kind of character.
6.1.4.2. Authentication function in access to user box
For the access request for each user box, after, the user who accesses is authenticated that it is
a user permitted the use of a user box concerned respectively.
Offers the user box authentication mechanism that is authenticated by the user box password
that consists of the character shown in Table 6.
After the user box is authenticated to the access from the network, it offers the user box
authentication mechanism using the session information besides the user box password.
According to protocol, it utilizes the 1010 session information or more, or generated and uses
the 1010 session information or more.
Return “*" for each character as feedback for the entered user box password.
Resets the number of authentication failure when succeeding in the authentication.
In case of the access from the panel, when it fails in the authentication, an input from the
panel is not accepted for five seconds.
When the authentication failure that becomes the 1-3 times in total is detected for the user
box concerned, the authentication function to the user box concerned is locked.
The administrator specifies the failure frequency threshold by the unauthorized access
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
50 / 90
detection threshold setting function.
The lock of the authentication function is released by the lock release function to the user box
of F.ADMIN executed or by the operation of the F.RESET function.
6.1.4.3. Access control to a user box file in a user box
The task to act for the user who is permitted to use the user box is related the "User Box ID" of
the user box as a user box attribute. This task is permitted the user box file, which has a
corresponding user box attribute to the user box attribute of a task, to do the printing, the
movement to other user boxes, and the copy operations to other user boxes.
6.1.4.4. Change of user box password
Change the user box password of the user box. When the user box password newly set satisfies
the following qualities, it is changed.
It is composed of the characters and by the number of digits shown in Table 6.
It shall not be composed of one kind of character.
6.1.5. F.PRINT（Secure Print Function）
F.PRINT is a series of security function related to the secure print such as the access control
function that allows the printing the secure print file after authenticating if a user is the
authorized user to use the secure print file for the access to the secure print file from the panel.
6.1.5.1. Authentication function by the secure print password
It authenticates that the accessing user is a user to whom the use of the secure print file
concerned is permitted, in response to the access request to each secure print file.
Offers the secure print authentication mechanism that is authenticated by the secure print
password that consists of the character shown in Table 6.
The secure print authentication mechanism by the separate session information is not
needed because it becomes only an access from the panel in the case of the secure print.
Return “*" for each character as feedback for the entered secure print password.
Resets the number of authentication failure when succeeding in the authentication.
The access from the panel is not accepted for 5 seconds when the authentication is failed.
When the authentication failure that becomes the 1-3 times in total for the secure print file
concerned is detected, the authentication function to the secure print file is locked.
The administrator specifies the failure frequency threshold by the unauthorized access
detection threshold setting function.
The lock is released by the lock release function to the secured print file of F.ADMIN executed
or the operation of the F.RESET function.
6.1.5.2. Access control function to a secure print file
The task to act for the user who is identified and authenticated has the authenticated secure
print internal control ID as the file attribute. This task is permitted the printing to the secure
print file with a corresponding file attribute to the file attribute of this task.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
51 / 90
6.1.5.3. Registration function of a secure print file
Following process is performed for the registration request of the secure print file.
① Registration of the secure print password
The registered secure print password is verified to meet the following requirements.
It is composed of the characters and by the number of digits shown in Table 6.
It shall not be composed of one kind of character.
② Giving of the secure print internal control ID
When the verification of the secure print password is completed in a registration request of
the secure print file, the secure print internal control ID uniquely identified is set to the
concerned secure print file.
6.1.6. F.OVERWRITE-ALL（All area overwrite deletion function）
F.OVERWRITE-ALL executes the overwrite deletion in the data area of HDD and initializes
the setting value of the password that is set to NVRAM as well. The object for the deletion or the
initialization is as follows.
＜Object for the deletion：HDD＞
Secure print file
User box file
On memory image file
Stored image file
Remaining image file
Image related file
User box password
Secure print password
Remaining TSF data
＜Object for the initialization：NVRAM＞
Administrator Password
SNMP password
Operation setting of HDD lock function（OFF）
Operation setting of Encryption function（OFF）
The deletion methods such as the data written in HDD and the written frequency is executed
according to the deletion method of all area overwrite deletion function set in F.ADMIN (Table 7).
The HDD lock password and the encryption passphrase cannot be used for being turned off the
operation setting of the HDD lock function and the encryption function. The setting of the
Enhanced Security function becomes invalid in the execution of this function. (Refer to the
description for the operation setting of the Enhanced Security function in F.ADMIN.)
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
52 / 90
6.1.7. F.CRYPT（Encryption key generation function）
F.CRYPT is generated the encryption key to encrypt all data written in HDD by using the
HDD encryption key generation algorithm (SHA-1) that is regulated by the Konica Minolta
encryption specification standard. Konica Minolta HDD encryption key generation algorithm
(SHA-1) is the algorithm to generate the encryption key by using the SHA-1 regulated by FIPS
180-1.
When the encryption passphrase is decided in the encryption functional operation setting to
which the access is restricted in F.ADMIN, the encryption key of 128bit length is generated from
the encryption passphrase by applying the SHA-1 algorithm.
6.1.8. F.HDD（HDD verification function）
F.HDD is a check function to permit reading from and writing in the HDD only when it is
verified that the illegal HDD is not installed and is confirmed validity when the HDD lock
password is set to HDD
When the HDD lock password is set to HDD, the status of HDD is confirmed in the HDD
operation verifying at the time of TOE starting. When the HDD lock password certainly being
set is returned as the result of status confirmation, the access to HDD is permitted. If the HDD
lock password not being set is returned, the access to HDD is refused because of an illegitimate
possibility.
6.1.9. F.RESET（Authentication Failure Frequency Reset Function）
F.RESET is a function to reset the number of authentication failure counted in each
authentication function including the administrator authentication. (Do not relate to the lock is
valid or not.)
This function operates by activating TOE such that the main power supply is turned on, it
returns from the power failure and so forth. When it starts, the following numbers of
authentication failure are reset. (The object account locked is released.)
The number of failure to authentication of administrator
The number of failure to authentication using SNMP password
The number of failure to authentication of service engineer
The number of failure to authentication of each user box
The number of failure to authentication of each secure print
6.2. TOE Security Strength of Function
The TOE security functions having probabilistic/permutational mechanisms are as follows.
The strength of each of the functions satisfies the SOF-Basic.
① Administrator authentication mechanism, HDD lock password verification mechanism,
and encryption passphrase verification mechanism which F.ADMIN offers
② CE authentication mechanism which F.SERVICE offers
③ Secure print authentication mechanism which F.PRINT offers
④ User box authentication mechanism which F.BOX offers
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
53 / 90
⑤ SNMP authentication mechanism which F.ADMIN-SNMP offers
6.3. Correspondence between TOE Security Functions and Function Requirements
The correspondence between TOE security function and TOE security function requirements
shows in Table 13 of 8.3 Rational for TOE Summary Specification. Table 13 shows that the TOE
security function corresponds to at least one TOE security function requirement.
6.4. Assurance Measures
The following table shows the assurance measures to meet the component of the TOE security
assurance requirements for EAL3 that are stipulated in Table 8.
Table 8 Correspondence between TOE Assurance Requirements and assurance measures
TOE Security Assurance Requirement Component TOE Security Assurance Requirement
CM capabilities ACM_CAP.3
Class ACM:
Configuration
management
CM scope ACM_SCP.1
・Configuration management plan
・Configuration List
・CM record
Delivery ADO_DEL.1 Delivery instructions
Class ADO:
Delivery and
Operation
Installation, generation
and start-up
ADO_IGS.1
・Service Manual
bizhub C450P Service Manual [Security
Function]（Japanese）
、bizhub C450P / ineo+
450P Service Manual [Security Function]
（English）
・User’s Guide
bizhub C450P User’s Guide [Security
Operations]（Japanese）
、bizhub C450P User's
Guide [Security Operations]（English）
、ineo+
450P User's Guide [Security Operations]
（English）
Functional specification ADV_FSP.1 Security function specifications
High-level design ADV_HLD.2 Security high level design specifications
Class ADV:
Development Representation
correspondence
ADV_RCR.1 Representation correspondence analysis report
Administrator guidance AGD_ADM.1
Class AGD:
Guidance Document
User Guidance AGD_USR.1
・Service Manual
bizhub C450P Service Manual [Security
Function]（Japanese）
、bizhub C450P / ineo+
450P Service Manual [Security Function]
（English）
・User’s Guide
bizhub C450P User’s Guide [Security
Operations]（Japanese）
、bizhub C450P User's
Guide [Security Operations]（English）
、ineo+
450P User's Guide [Security Operations]
（English）
Class ALC:
Life Cycle Support
Development security ALC_DVS.1 Development security instructions
Coverage ATE_COV.2 Coverage analysis report
Depth ATE_DPT.1 Depth analysis report
Functional tests ATE_FUN.1 Test specification and results report
Class ATE:
Test
Independent testing ATE_IND.2 Printer control software including TOE
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
54 / 90
TOE Security Assurance Requirement Component TOE Security Assurance Requirement
Misuse AVA_MSU.1
※ no specific document
（Reflected in the guidance documents）
Strength of TOE security
functions
AVA_SOF.1
Class AVA:
Vulnerability
Assessment
Vulnerability analysis AVA_VLA.1
Vulnerability analysis report
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
55 / 90
7. PP Claims
There is no conformance to a PP in this ST.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
56 / 90
8. Rational
8.1. Security Objectives Rationale
8.1.1. Necessity
The correspondence between the assumptions, threats and security objectives are shown in the
following table. It shows that the security objectives correspond to at least one assumption or
threat.
Table 9 Conformity of Security Objectives to assumptions and Threats
Assumption/Treat
Security objectives
A.ADMIN
A.SERVICE
A.NETWORK
A.SECRET
A.SETTING
T.DISCARD-PRINTER
T.BRING-OUT-STORAGE
T.ACCESS-BOX
T.ACCESS-SECURE-PRINT
T.ACCESS-NET-SETTING
T.ACCESS-SETTING
T.BACKUP-RESTORE
O.BOX ●
O.SECURE-PRINT ●
O.CONFIG ● ● ●
O.OVERWRITE-ALL ●
O.CRYPT-KEY ●
O.CHECK-HDD ●
OE.CRYPT ●
OE.LOCK-HDD ●
OE.FEED-BACK ● ● ● ● ●
OE-N.ADMIN ●
OE-N.SERVICE ●
OE-N.NETWORK ●
OE-N.SECRET ●
OE-N.SESSION ● ● ● ● ●
OE-S.SETTING-SECURITY ●
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
57 / 90
8.1.2. Sufficiency of Assumptions
The security objectives for the assumptions are described as follows.
A.ADMIN（Personnel Conditions to be an Administrator ）
This condition assumes that administrators are not malicious.
With OE-N.ADMIN, the organization that uses the Printer assigns personnel who are reliable
in the organization that uses the Printer, so the reliability of the administrator is realized.
A.SERVICE（Personnel Conditions to be a Service Engineer）
This condition assumes the service engineer are not malicious.
With OE-N.SERVICE, the organization that manages the maintenance of the Printer
educates the service engineer. Also the administrator needs to observe the maintenance of the
Printer, so that the reliability of service engineers is assured.
A.NETWORK（Network Connection Conditions for the Printer）
This condition assumes that there are no wiretapping activities for the intra-office LAN and
no access by an unspecified person from an external network.
OE-N.NETWORK regulates the wiretapping prevention by the installation of devices such as
a wiretapping detection device and device to perform the encryption communication on the
intra-office LAN. It also regulates the unauthorized access prevention from external by the
installation of devices such as firewall in order to block access to the Printer from the external
networks, so that this condition is realized.
A.SECRET（Operating condition concerning confidential information）
This condition assumes each password and encryption passphrase using for the use of TOE
should not be leaked by each user.
OE-N.SECRET regulates that the administrator makes the user to execute the operation rule
concerning the secure print password and the user box password, and that the administrator
executes the operation rule concerning the administrator password, the HDD lock password,
SNMP password and encryption passphrase. It also regulates that the service engineer
executes the operation rule concerning the CE password, and that the service engineer makes
the administrator to execute the operation rule concerning the administrator password, so
that this condition is realized.
A.SETTING（Enhanced Security Function Operational Settings Condition）
This condition assumes the enhanced security function operational settings condition is
satisfied.
OE-N.SETTING-SECURITY regulates that this is used after the administrator activates the
enhanced security function, so that this condition is realized.
8.1.3. Sufficiency of Threats
The security objectives against threats are described as follows.
T.DISCARD-PRINTER（Lease return and disposal of Printer）
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
58 / 90
This threat assumes the possibility of leaking information from HDD inside The printer
collected from the user.
O.OVERWRITE-ALL is that TOE offers the function to overwrite data for the deletion to all
area of HDD, so that the possibility of the threat is removed by executing this function before
The printer is collected.
Accordingly, this threat is countered sufficiently.
T.BRING-OUT-STORAGE（Unauthorized taking out of HDD）
This threat assumes the possibility that the image data in HDD leaks by being stolen from the
operational environment under The printer used or by installing the unauthorized HDD and
taking away with the data accumulated in it.
For the above, the possibility of the threat is removed because at least either of the following
two measures is selected by the administrator.
①O.CRYPT-KEY generates the encryption key for TOE to encrypt data to be written in
HDD, and the encryption board encodes data by OE.CRYPT.
②OE.LOCK-HDD doesn't permit to read data from any other Printer, as a function of the
HDD, but the Printer where this HDD is installed.
In the above-mentioned, when only ② is selected, danger of leaking exists by taking out the
another HDD without the function of ② having been secretly replaced. For the above,
because the validity of HDD installed by TOE is verified by O.CHECK-HDD, data is not
written in the HDD replaced secretly. The possibility of the threat is removed consequently.
Accordingly, this threat is countered sufficiently.
T.ACCESS-BOX（Unauthorized access to user box using user function）
This threat assumes the possibility that an unauthorized operation is done by using the user
function for the user box which each user uses to store the image file.
The operation of user box and the user box file in a user box is restricted only to the user who
is the owner by O.BOX, so that the possibility of the threat is removed.
OE.FEED-BACK regulates to return the protected feedback for the entered password in the
user box authentication, and OE-N.SESSION also requires the log-off operation after the
operation ends, so that O.BOX are supported sufficiently.
Accordingly, this threat is countered sufficiently.
T.ACCESS-SECURE-PRINT（Unauthorized access to a secure print file）
This threat assumes the possibility that an unauthorized operation is done to the secure print.
The operation of the secure print is limited only to the authorized user by O.SECURE-PRINT,
so that the possibility of the threat is removed.
OE.FEED-BACK regulates to return the protected feedback for the entered password in the
access authentication to the secure print, and OE-N.SESSION requires the log-off operation
after the operation ends, so that O.SECURE-PRINT are supported sufficiently.
Accordingly, this threat is countered sufficiently.
T.ACCESS-NET-SETTING（Unauthorized change in network setting ）
This threat assumes the possibility to use the print function to the unauthorized entity from
PC by the user who believes as TOE when the network setting which is related to the address
of The printer is modified illegally. Especially, it becomes a problem if a secure print file which
is required to be concealed from other users in the office is transmitted to the unauthorized
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
59 / 90
entity.
On the other hand, O.CONFIG regulates that the role to operate the network setting relating
to the transmission of TOE is limited to the administrator, and so the possibility of this threat
is removed.
OE.FEED-BACK regulates that the feedback protected is returned for the entered password
by the administrator's authentication and OE-N.SESSION requires to logoff after the
operation ends, so that O.CONFIG is supported sufficiently.
Accordingly, this threat is countered sufficiently.
T.ACCESS-SETTING（Unauthorized change of function setting condition related to security）
This threat assumes the possibility of developing consequentially into the leakage of the user
box file and the secure print file by having been changed the specific function setting which
relates to security.
O.CONFIG regulates that only the administrator is permitted to perform the setting of the
enhanced security function that controls all setting function related to a series of security, and
so the possibility of the threat is removed.
OE.FEED-BACK regulates that the feedback protected is returned for the entered password
by the administrator's authentication, and OE-N.SESSION is also requested to logoff
respectively after the operations of the administrator mode ends, so that O.CONFIG is
supported sufficiently.
Accordingly, this threat is countered sufficiently.
T.BACKUP-RESTORE（Unauthorized use of back-up function and restoration function）
This threat assumes a possibility that the user box file or the secure print file may leak since
the back-up function or the restoration function being illegally used. Moreover, this assumes
that because of a leak of confidential data such as the password, the various setting values are
falsified and there is a similar possibility that the user box file or the secure print file may
leak.
O.CONFIG regulates that the use of the back-up function and the restoration function is
permitted only to the administrator, so that the possibility of the threat is removed.
OE.FEED-BACK regulates that the protected feedback is returned for the entered password
by the administrator authentication and OE-N.SESSION is also requested the log-off
operation after the operation ends, and so O.CONFIG is sufficiently supported.
Accordingly, this threat is countered sufficiently.
8.1.4. Sufficiency of Organizational Security Policies
The organizational security policy is not applied.
8.2. IT Security Requirements Rationale
8.2.1. Rationale for IT Security Functional Requirements
8.2.1.1. Necessity
The correspondence between the security objectives and the IT security functional
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
60 / 90
requirements are shown in the following table. It shows that the IT security functional
requirements correspond to at least one security objective.
Table 10 Conformity of IT Security Functional Requirements to Security Objectives
Security Objective
Security
Functional
Requirements
O.BOX
O.SECURE-PRINT
O.CONFIG
O.OVERWRITE-ALL
O.CRYPT-KEY
O.CHECK-HDD
OE.CRYPT
OE.LOCK-HDD
OE.FEED-BACK
※
set.admin
※
set.service
set.admin ● ● ●
set.service ● ● ●
FCS_CKM.1 ●
FDP_ACC.1[1] ● ●
FDP_ACC.1[2] ● ●
FDP_ACC.1[3] ●
FDP_ACF.1[1] ● ●
FDP_ACF.1[2] ● ●
FDP_ACF.1[3] ●
FIA_AFL.1[1] ●
FIA_AFL.1[2] ●
FIA_AFL.1[3] ●
FIA_AFL.1[4] ●
FIA_AFL.1[5] ●
FIA_AFL.1[6] ● ● ● ●
FIA_ATD.1 ● ●
FIA_SOS.1[1] ● ●
FIA_SOS.1[2] ●
FIA_SOS.1[3] ●
FIA_SOS.1[4] ● ●
FIA_SOS.1[5] ● ●
FIA_SOS.2 ● ●
FIA_UAU.2[1] ●
FIA_UAU.2[2] ● ●
FIA_UAU.2[3] ●
FIA_UAU.2[4] ●
FIA_UAU.6 ● ● ●
FIA_UAU.7 ● ● ● ●
FIA_UID.2[1] ●
FIA_UID.2[2] ● ●
FIA_UID.2[3] ●
FIA_UID.2[4] ●
FIA_USB.1 ● ●
FMT_MOF.1[1] ●
FMT_MOF.1[2] ●
FMT_MSA.3 ●
FMT_MTD.1[1] ● ● ● ● ●
FMT_MTD.1[2] ● ●
FMT_MTD.1[3] ●
FMT_MTD.1[4] ●
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
61 / 90
Security Objective
Security
Functional
Requirements
O.BOX
O.SECURE-PRINT
O.CONFIG
O.OVERWRITE-ALL
O.CRYPT-KEY
O.CHECK-HDD
OE.CRYPT
OE.LOCK-HDD
OE.FEED-BACK
※
set.admin
※
set.service
FMT_MTD.1[5] ●
FMT_MTD.1[6] ● ●
FMT_SMF.1 ● ● ● ● ●
FMT_SMR.1[1] ● ● ●
FMT_SMR.1[2] ● ● ● ●
FMT_SMR.1[3] ●
FPT_RVM.1 ● ● ● ●
FPT_SEP.1 ● ● ●
FNEW_RIP.1 ●
FIA_NEW.1 ●
FCS_COP.1[E] ●
FIA_AFL.1[E] ●
FIA_UAU.2[E] ●
FIA_UAU.7[E] ●
Note) set.admin and set.service indicates the set of the requirements. And the security
objectives assumed to have the correspondence and presented by "●" also correspond to a
series of requirement set associated by ※ set.admin and ※ set.service shown in column.
8.2.1.2. Sufficiency
The IT security functional requirements for the security objectives are described as follows.
O.BOX（user box access control）
This security objective limits access to the user box and the user box file in the user box to
only the user who owns that user box, and needs various requirements that relate to the
access control.
＜User box access control (a user box)＞
In order to operate the user box file in a user box, the user needs to be the one who is
permitted to use the user box. FIA_UID.2[4] and FIA_UAU.2[4] identifies and authenticates
that it is a user who is permitted the use of the user box.
FIA_UAU.7 returns “*" for each entered character as feedback protected by the panel and
supports the authentication.
In the case of the failure authentication from the panel, FIA_AFL.1 [6] refuses all input
acceptances from the panel for 5 seconds in every failure. When the authentication failure
reaches 1-3 times, FIA_AFL.1 [5] logoffs if it's under authentication, and locks the
authentication function for that user from then on. This lock status is released by the TOE
rebooting or the administrator's release operation.
FMT_MTD.1[1] permits only to the administrator the setting of the threshold of the
unauthorized access detection value that is the trial frequency of the failure authentication in
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
62 / 90
the authentication of the user who is permitted the use of the user box.
When FIA_ATD.1 and FIA_USB.1 relates a user box ID to the task of acting use,
FDP_ACC.1[1] and FDP_ACF.1[1] permit the user box file that has a corresponding object
attribute to the user box ID of the subject attribute the operation such as a print, a movement
to other user box, and a copy to other user box.
＜Management of a user box＞
FMT_MTD.1[2] permits the change in the user box password only to the administrator and
the user who is permitted to the use of the user box. FIA_SOS.1[4] verifies the quality of the
user box password. Moreover, FIA_SOS.1[5] performs the quality verification of the session
information used in the user box authentication via the network, and FIA_SOS.2 secures the
quality of the session information which is generated and used.
＜Necessary requirement to keep the administrator secure＞
⇒ refer to set.admin
＜Necessary requirement to keep the service engineer secure＞
⇒ refer to set.service
＜Role and controlling function for each management＞
As the role of doing these managements, FMT_SMR.1[2] maintains an administrator and
FMT_SMR.1[3] maintains a user permitted the use of the user box. FMT_SMF.1 specifies
these management functions.
This security objective is satisfied by the completion of these multiple functional
requirements.
O.SECURE-PRINT（Secure print file access control）
This security objective limits the print of the secure print file only for the user, who is
permitted the use of the secure print file, and requires various requirements that relate to the
access control.
＜Secure print file access control＞
As it must be a user who is permitted the use of the secure print file to print it, FIA_UID.2[3]
and FIA_UAU.2[3] identifies and authenticates that it is a user who is permitted the use of
the secure print file.
FIA_UAU.7 returns “*" for each entered character as feedback protected by the panel and
supports the authentication.
FIA_AFL.1 [6] refuses all input acceptances from the panel for 5 seconds in every failure.
When the authentication failure reaches 1-3 times, FIA_AFL.1 [4] locks the authentication
function for to the concerned secure print file. This lock status is released by the TOE
rebooting or the administrator's release operation.
FMT_MTD.1[1] permits only to the administrator the setting of the threshold of the
unauthorized access detection value that is the trial frequency of the failure authentication in
the authentication of the user who is permitted the use of the secure print file.
When FIA_ATD.1 and FIA_USB.1 relate the secure print internal control ID to the task of
acting use, FDP_ACC.1[2] and FDP_ACF.1[2] permit the print operation to the secure print
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
63 / 90
file that has a corresponding object attribute to the secure print internal control ID of the
subject attribute.
As for secure print internal control ID, FMT_MSA.3 gives the value uniquely identified when
the secure print file is registered.
＜Secure print password＞
FIA_SOS.1[4] verifies the quality of the secure print password.
＜Necessary requirement to keep the administrator secure＞
⇒ refer to set.admin
＜Necessary requirement to keep the service engineer secure＞
⇒ refer to set.service
＜Role and controlling function for each management＞
As the role of doing these managements, FMT_SMR.1[2] maintains an administrator.
Moreover, FMT_SMF.1 specifies these management functions.
This security objective is satisfied by the completion of these multiple functional
requirements.
O.CONFIG（Access limitation to an management function）
This security objective limits the setting related to the IP address of the printer, the setting
related to the Enhanced Security function, the backup function and the restorations function
to the administrator, and needs various requirements to limit the access to a series of setting
function and the management function.
＜Management of network setting＞
When the administrator attribute is associated with the task of substituting the use,
FDP_ACC.1[3] and FDP_ACF.1[3] permits the task of substituting the user to operate the
setting for the Printer address group object.
＜Operation limitation of Backup and restoration function＞
When the administrator attribute is related to the task of acting the use, the task of acting the
user is permitted the back-up operation of;
･ the user box files by FDP_ACC.1[1] and FDP_ACF.1[1].
･ the secure print files by FDP_ACC.1[2] and FDP_ACF.1[2].
･ the encryption passphrase object and the HDD lock password object by FDP_ACC.1[3]
and FDP_ACF.1[3].
In addition, the restoration operation is permitted for
･ the encryption passphrase object, the HDD lock password object and the Printer address
group object by FDP_ACC.1[3] and FDP_ACF.1[3].
Moreover, the restoration operation (modifying operation) of the followings is permitted only
to the administrator.
･ the Enhanced security setting data by FMT_MOF.1[1].
･ the SNMP password, the authentication failure frequency, the secure print password by
FMT_MTD.1[1].
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
64 / 90
･ the user box password by FMT_MTD.1[2].
FMT_MTD.1[4] permits only to the administrator the backup operation (inquiry operation) of
the SNMP password, the user box password, and the secure print password.
＜Operational limitation of Enhanced Security function＞
FMT_MOF.1[1] permits only the administrator and service engineer to disable the setting for
the enhanced security function. FMT_MOF.1[3] permits only the service engineer to enable
the setting for the setup function
＜Management of HDD lock password and encryption passphrase＞
When the administrator attribute is related to the task of acting the user, FDP_ACC.1[3] and
FDP_ACF.1[3] permit the setting operation to the HDD lock password object and the
encryption passphrase object to the task of acting the user. FIA_SOS.1[3] verifies the quality
of the HDD lock password and the encryption passphrase. In order to change the HDD lock
password and encryption passphrase, FIA_UAU.6 re-authenticates that a user is an
administrator by collating with the registered HDD lock password and encryption passphrase.
When the authentication is succeeded, the HDD lock password and the encryption passphrase
are allowed to be changed.
Moreover, when the CE attribute is related to the task of acting the user, FDP_ACC.1[3] and
FDP_ACF.1[3] permit the setting operation to the HDD lock password object and the
encryption passphrase object to the task of acting the user.
＜Necessary requirement for accessing MIB object＞
The Printer address group object exists as an MIB object as well, so that the restriction is
necessary even in the access from the SNMP.
FIA_UID.2[2] and FIA_UAU.2[2] identify and authenticate that the user who accesses the
MIB object is an administrator.
FIA_AFL.1[3] locks the authentication function to access the MIB object when the failure
authentication reaches 1-3 times. This lock is released by the start of TOE or the lock release
operation by the administrator.
FMT_MTD.1[1] restricts the threshold setting of the unauthorized access detection value that
is the trial frequency of the failure authentication in the administrator authentication using
the SNMP password only to the administrator
FMT_MTD.1[1] restricts the change in the SNMP password to the administrator.
FIA_SOS.1[2] verifies the quality of the SNMP password.
FMT_MTD.1[6] restricts the initialization of the SNMP password only to the administrator
and the service engineer.
FMT_MOF.1[2] restricts the method of the SNMP password authentication function only to
the administrator.
＜Necessary requirement to keep the administrator secure＞
⇒ refer to set.admin
＜Necessary requirement to keep the service engineer secure＞
⇒ refer to set.service
＜Role and controlling function for each management＞
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
65 / 90
As the role of doing these managements, FMT_SMR.1[1] maintains a service engineer and
FMT_SMR.1[2] maintains an administrator. Moreover, FMT_SMF.1 specifies these
management functions.
This security objective is satisfied by the completion of these multiple functional
requirements.
O.OVERWRITE-ALL（Complete over write deletion）
This security objective regulates that it deletes all data areas of HDD and initializes the
concealed information of NVRAM that is set by the user, and requires various requirements
that relate to the deletion.
FNEW_RIP.1 guarantees that these objective information not to be able to use the content of
any previous information by the deletion operation.
This security objective is satisfied by the completion of these multiple functional
requirements.
O.CRYPT-KEY（Encryption key generation）
This security objective regulates that, when the encryption board is installed, the encryption
key necessary to encrypt all the data written in HDD is generated, and needs various
requirements that relate to the encryption key generation.
Using Konica Minolta HDD encryption key generation mechanism (SHA-1) according to
Konica Minolta encryption specification standard, FCS_CKM.1 generates the 128bit
encryption key. Konica Minolta HDD encryption key generation algorithm is not the general
standard algorithm that is recognized, but it is the algorithm using SHA-1 specified with
FIPS 180-1, and so this is the algorithm with sufficient strength which does not undermine
the entropy of 128 bit, and does not undermine the strength level that is required by security
objective. (Refer to chapter 6 TOE summary specification for the description related to this
algorithm)
This security objective is satisfied by the completion of these multiple functional
requirements.
O.CHECK-HDD（Validity confirmation of HDD）
This security objective regulates that it verifies the validity of HDD in order to confirm the
unauthorized HDD doesn't exist, and needs various requirements that relate to the
verification of an external entity from TOE.
FIA_NEW.1 identifies HDD before the action from TOE to HDD, and cancels the scheduled
action when the identification fails.
This security objective is satisfied by the completion of this function requirement.
OE.CRYPT（Encryption of HDD）
This security objective regulates that the data stored in HDD is encrypted by the encryption
board that is the entity of a necessary IT environment for the security maintenance of TOE,
and needs various requirements that relate to the encryption.
Applying FCS_COP.1[E], the encryption board encodes and decodes all the written data to
HDD by the 128bit encryption key using AES that conforms to FIPS PUB 197.
This security objective is satisfied by the completion of this function requirement.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
66 / 90
OE.LOCK-HDD（Access control of HDD）
This security objective regulates that it refuses the unauthorized access from the printer other
than the one that is set by the HDD which is the entity of a necessary IT environment for the
TOE security maintenance, and needs various requirements that verify that it is the right
Printer where TOE is installed.
By FIA_UAU.2[E], HDD authenticates that the entity accessing to HDD is the Printer, which
HDD is installed.
When the failure authentication reaches five times, FIA_AFL.1[E] refuses all the accesses to
HDD concerning reading and writing data.
This security objective is satisfied by the combination of these multiple functional
requirements.
OE.FEED-BACK（Feedback of password）
This security objective regulates that the application (used by client PC for accessing to the
Printer) that is the entity of a necessary IT environment for the TOE security maintenance
offers the appropriate protected feedback for the entered user box password and the entered
administrator password.
By FIA_UAU.7[E], the application displays “*" for each character as feedback for entered
character data.
This security objective is satisfied by the completion of this function requirement.
The following is the compilation of set such as ①the set of necessary requirement to keep
administrator secure (set.admin), ②the set of necessary requirement to keep service engineer
secure (set.service).
set.admin（Set of necessary requirement to keep administrator secure）
＜Identification and Authentication of an administrator＞
FIA_UID.2[2] and FIA_UAU.2[2] identifies and authenticates that the accessing user is an
administrator.
FIA_UAU.7 returns “*" for each character entered as feedback protected in the panel, and
supports the authentication.
FIA_AFL.1[6] refuses, in case of the failure authentication tried from the panel, all the input
receipts from the panel for five seconds in every failure. When the failure authentication
reaches 1-3 times, FIA_AFL.1[2] locks all the authentication functions that use the
administrator password from then on. This lock is released by starting TOE with turning OFF
and ON the power supply.
FMT_MTD.1[1] permits only to the administrator the setting of the threshold of the
unauthorized access detection value which is the trial frequency of the failure authentication
in the administrator authentication.
＜Management of administrator's authentication information＞
FIA_SOS.1[1] verifies the quality of the administrator password. Moreover, FIA_SOS.[5]
verifies the quality of session information used to authenticate the administrator via the
network, and FIA_SOS.2 secures the quality of session information that is generated and
used. FMT_MTD.1[3] restricts the change in the administrator password to the administrator
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
67 / 90
and the service engineer. When the administrator changes the administrator password,
FIA_UAU.6 re-authenticates it. In this re-authentication, when the failure authentication
reaches 1-3 times, FIA_AFL.1[2] releases the authentication status of the administrator from
then on. And it locks all the authentication functions to use the administrator password. This
lock is released by starting TOE such as turning OFF and ON the power supply.
Moreover, FMT_MTD.1[6] restricts the initialization of the administrator password to the
administrator and the service engineer.
＜Role and management function for each management＞
FMT_SMR.1[1] have service engineer maintain the role to do these management, and
FMT_SMR.1[2] have the administrator do the same. Additionally, FMT_SMF.1 specifies these
management functions.
set.service（Set of necessary requirement to keep service engineer secure）
＜Identification and Authentication of a service engineer＞
FIA_UID.2[1] and FIA_UAU.2[1] identifies and authenticates that the accessing user is a
service engineer.
FIA_UAU.7 returns "*" every one character entered as the feedback protected in the panel,
and supports the authentication.
FIA_AFL.1[6] refuses all the input receipts from the panel for five seconds at each failure,
and when the failure authentication reaches 1-3 times, FIA_AFL.1[1] locks all the
authentication functions to use the CE password. This lock is released by starting TOE such
as turning OFF and ON the power supply.
FMT_MTD.1[1] permits only to the administrator the setting of the threshold of the
unauthorized access detection value that is the trial frequency of the failure authentication in
the service engineer authentication.
＜Management of service engineer's authentication information＞
FIA_SOS.1[1] verifies the quality of the CE password. FMT_MTD.1[5] restricts the change in
the CE password to the service engineer. Moreover, FIA_UAU.6 re-authenticates it. In this
re-authentication, when the failure authentication reaches 1-3 times, FIA_AFL.1[1] releases
the authentication status of the service engineer and locks all the authentication functions to
use the CE password. This lock is released by starting TOE such as turning OFF and ON the
power supply.
＜Role and management function for each management＞
FMT_SMR.1[1] maintains the role to do these management as a service engineer.
FMT_SMF.1 specifies these management functions.
FPT_RVM.1 and FPT_SEP.1 are the security function requirements directly not related to the
security measures policy, though it not included in the explanation of the above-mentioned
sufficiency. But, they are shown to support the security function requirement which is included
in the explanation of the above-mentioned sufficiency in the mutual support described later.
Because these two security function requirements will relate to the security objective that
corresponds to the security function requirement supported respectively by two security function
requirements, the relation with the security objective is consequentially clear.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
68 / 90
8.2.1.3. Necessity of specified IT security function requirement
In this ST, FNEW_RIP.1 and FIA_NEW.1 is stated as an extended requirement. The necessity
that presents these requirements and the validity of the assurance requirement applied in
guaranteeing requirements is described as follows.
Extended requirement：Necessity of FNEW_RIP.1
Regarding FNEW_RIP.1, FDP_RIP.1 is the closest requirement in the viewpoint of remaining
information protection, but the requirement needs to regulate the protection of not only user
data, but also the TSF data. And so, it is improper in the function requirement concerned that
exists in the class of the user data protection, and it requires the extended requirement.
＜Validity of requirement identification structure＞
Because this requirement doesn't have the corresponding class in the data protection class of
integration of no division of the TSF data and the user data, a new class named FNEW was
set up, the same family name as the RIP family of the FDP class that indicates the remaining
information protection, and clarifies the identification.
Though the predicted management activity is assumed not to be existed, as for the timing of
information assuming not to be able to recycle in the requirement is stipulated concretely,
especially, the parameter treated as changeability are not guessed in this requirement. In
addition, it is shown that the execution record has been left at the predicted audit activity
with the user identification.
Extended requirement：Necessity of FIA_NEW.1
Regarding FIA_NEW.1, FIA_UID.1 or FIA_UID.2 is the closest requirement in the viewpoint
of identification. But the verification act of HDD doesn't approve the act accessed from an
external entity by TOE, but also approve the act that TOE itself assigns to an external entity.
It is improper in the function requirement concerned, and the extended requirement is
necessary.
＜Validity of requirement identification structure＞
Because this requirement is one of the identification requirements, the family named NEW is
set as a family added to the FIA class, and clarifies the identification.
As an activity that is predicted on management, FIA_UID requirement and similar
management items are assumed. Also, an activity that is predicted on audit, FIA_UID
requirement and similar audit item are assumed.
8.2.1.4. Assurance validity of specified IT security function requirement
Two specified function requirements (FNEW_RIP.1, FIA_NEW.1) are not the greatly extended
concept of the function requirement provided by CC part 2, and high contents of novelty. This is
not the one to assume the necessity of presenting the TSP model specially or the possibility of a
potential hiding channel in order to evaluate this function requirement accurately.
Therefore, it is possible to assure sufficiently the validity of the function that these functional
requirements show by the set of the assurance requirement of EAL3, and a special assurance
requirement and the assurance requirement required at EAL4 or higher are not required.
8.2.1.5. Dependencies of the IT Security Functional Requirements
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
69 / 90
The dependencies of the IT security functional requirements components are shown in the
following table. When a dependency regulated in CC Part 2 is not satisfied, the reason is
provided in the section for the “dependencies Relation in this ST.”
Table 11 Dependencies of IT Security Functional Requirements Components
N/A：Not Applicable
Functional
Requirements
Component for
this ST
Dependencies on CC Part 2 Dependencies Relation in this ST
FCS_CKM.1
FCS_CKM.2 or FCS_COP.1、
FCS_CKM.4、
FMT_MSA.2
FCS_COP.1[E]
＜The reason not to apply①FCS_CKM.4, ②
FMT_MSA.2＞
① The encryption key is regularly kept for the stored
data. Moreover, an arbitrary access to the storage
medium is difficult, and there is no necessity of the
encryption key cancellation.
② TOE does not have the security attribute to be
managed for the encryption key, and so it is not
necessary to regulate a security attribute that is
secure.
FDP_ACC.1[1] FDP_ACF.1 FDP_ACF.1[1]
FDP_ACC.1[2] FDP_ACF.1 FDP_ACF.1[2]
FDP_ACC.1[3] FDP_ACF.1 FDP_ACF.1[3]
FDP_ACF.1[1]
FDP_ACC.1、
FMT_MSA.3
FDP_ACC.1[1]、
<The reason not to apply FMT_MSA.3>
There is no necessity for applying this requirement
because the security attribute that requires the secure
management for the generated object does not exist.
(User box ID can be registered by the arbitrary user.)
FDP_ACF.1[2]
FDP_ACC.1、
FMT_MSA.3
FDP_ACC.1[2]
FMT_MSA.3
FDP_ACF.1[3]
FDP_ACC.1、
FMT_MSA.3
FDP_ACC.1[3]
＜The reason not to apply FMT_MSA.3＞
There is no necessity for applying this requirement
because the object attribute doesn't exist.
FIA_AFL.1[1] FIA_UAU.1 FIA_UAU.2[1]
FIA_AFL.1[2] FIA_UAU.1 FIA_UAU.2[2]
FIA_AFL.1[3] FIA_UAU.1 FIA_UAU.2[2]
FIA_AFL.1[4] FIA_UAU.1 FIA_UAU.2[3]
FIA_AFL.1[5] FIA_UAU.1 FIA_UAU.2[4]
FIA_AFL.1[6]
FIA_UAU.1 FIA_UAU.2[1]、FIA_UAU.2[2]、FIA_UAU.2[3]、
FIA_UAU.2[4]
FIA_ATD.1 None N/A
FIA_SOS.1[1] None N/A
FIA_SOS.1[2] None N/A
FIA_SOS.1[3] None N/A
FIA_SOS.1[4] None N/A
FIA_SOS.1[5] None N/A
FIA_SOS.2 None N/A
FIA_UAU.2[1] FIA_UID.1 FIA_UID.2[1]
FIA_UAU.2[2] FIA_UID.1 FIA_UID.2[2]
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
70 / 90
Functional
Requirements
Component for
this ST
Dependencies on CC Part 2 Dependencies Relation in this ST
FIA_UAU.2[3] FIA_UID.1 FIA_UID.2[3]
FIA_UAU.2[4] FIA_UID.1 FIA_UID.2[4]
FIA_UAU.6 None N/A
FIA_UAU.7
FIA_UAU.1 FIA_UAU.2[1]、FIA_UAU.2[2]、FIA_UAU.2[3]、
FIA_UAU.2[4]
FIA_UID.2[1] None N/A
FIA_UID.2[2] None N/A
FIA_UID.2[3] None N/A
FIA_UID.2[4] None N/A
FIA_USB.1 FIA_ATD.1 FIA_ATD.1
FMT_MOF.1[1]
FMT_SMF.1、
FMT_SMR.1
FMT_SMF.1、
FMT_SMR.1[1]、FMT_SMR.1[2]
FMT_MOF.1[2]
FMT_SMF.1、
FMT_SMR.1
FMT_SMF.1、
FMT_SMR.1[2]
FMT_MOF.1[3]
FMT_SMF.1、
FMT_SMR.1
FMT_SMF.1、
FMT_SMR.1[1]
FMT_MSA.3
FMT_MSA.1、
FMT_SMR.1
FMT_MSA.1[1]、FMT_MSA.1[2]、
FMT_SMR.1[3]
FMT_MSA.3[2]
FMT_MSA.1、
FMT_SMR.1
Neither is applicable.
＜The reason not to apply FMT_MSA.1＞
This is the internal control ID that is identified
uniquely, and this does not require the management
such as change or deletion, after this is assigned once.
＜FMT_SMR.1＞
The assignment of FMT_MSA.3.2 is not applicable.
FMT_SMR.1 is the dependency that is set relating to
the following and so there is no necessity of
application.
FMT_MTD.1[1]
FMT_SMF.1、
FMT_SMR.1
FMT_SMF.1、
FMT_SMR.1[2]
FMT_MTD.1[2]
FMT_SMF.1、
FMT_SMR.1
FMT_SMF.1、
FMT_SMR.1[2] 、FMT_SMR.1[3]
FMT_MTD.1[3]
FMT_SMF.1、
FMT_SMR.1
FMT_SMF.1、
FMT_SMR.1[2]
FMT_MTD.1[4]
FMT_SMF.1、
FMT_SMR.1
FMT_SMF.1、
FMT_SMR.1[2]、FMT_SMR.1[4]
FMT_MTD.1[5]
FMT_SMF.1、
FMT_SMR.1
FMT_SMF.1、
FMT_SMR.1[2]、FMT_SMR.1[3]
FMT_MTD.1[6]
FMT_SMF.1、
FMT_SMR.1
FMT_SMF.1、
FMT_SMR.1[1]、FMT_SMR.1[2]
FMT_SMF.1 None N/A
FMT_SMR.1[1] FIA_UID.1 FIA_UID.2[1]
FMT_SMR.1[2] FIA_UID.1 FIA_UID.2[2]
FMT_SMR.1[3] FIA_UID.1 FIA_UID.2[4]
FPT_RVM.1 None N/A
FPT_SEP.1 None N/A
FNEW_RIP.1 None N/A
FIA_NEW.1 None N/A
FCS_COP.1[E]
FDP_ITC.1 or FCS_CKM.1、
FCS_CKM.4、
FMT_MSA.2
FCS_CKM.1
＜The reason not to apply①FCS_CKM.4、②
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
71 / 90
Functional
Requirements
Component for
this ST
Dependencies on CC Part 2 Dependencies Relation in this ST
FMT_MSA.2＞
① The encryption key is regularly kept for the stored
data. Moreover, an arbitrary access to the storage
medium is difficult, and there is no necessity of the
encryption key cancellation.
② TOE does not have the security attribute to be
managed for the encryption key, it is not necessary
to be regulated a security attribute that is secure.
FIA_AFL.1[E] FIA_UAU.1 FIA_UAU.2[E]
FIA_UAU.2[E]
FIA_UID.1 N/A
＜The reason not to apply FIA_UID.1＞
This regulates the access to HDD installed in the
Printer. There are no multiple access routes because
the access to HDD is done through a general IDE
interface.
In other words, when the some users access, it is
unnecessary for this processing the authentication
information that each user accessing is needed, and
there is no necessity of the identification of the entity
to access.
FIA_UAU.7[E] FIA_UAU.1 FIA_UAU.2[2]、FIA_UAU.2[4]
8.2.1.6. Mutual Support Correlations of IT Security Functional Requirements
The IT security function requirements to operate effectively other security functional
requirements which are not specified in the analysis of the dependencies relation of the
functional requirement are shown in the table below.
Table 12 Mutual Support Correlations of IT Security Functional Requirements
N/A：Not Applicable
Functional requirement component
that operates other security functional requirements validly
IT Security
Functional
Requirement ①Bypass
Prevention
②Interference/
Destruction
Prevention
③Deactivation
Prevention
④Disabling
Detection
FCS_CKM.1 N/A N/A FMT_MOF.1[1] N/A
FDP_ACC.1[1] N/A N/A FMT_MOF.1[1] N/A
FDP_ACC.1[2] N/A N/A FMT_MOF.1[1] N/A
FDP_ACC.1[3] N/A N/A FMT_MOF.1[1] N/A
FDP_ACF.1[1]
FIA_UAU.2[2]
FIA_UAU.2[4]
FPT_SEP.1 FMT_MOF.1[1] N/A
FDP_ACF.1[2]
FIA_UAU.2[2]
FIA_UAU.2[3]
FPT_SEP.1 FMT_MOF.1[1] N/A
FDP_ACF.1[3]
FIA_UAU.2[2]
FIA_UAU.2[1]
FPT_SEP.1 FMT_MOF.1[1] N/A
FIA_AFL.1[1] N/A FMT_MTD.1[1] FMT_MOF.1[1] N/A
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
72 / 90
Functional requirement component
that operates other security functional requirements validly
IT Security
Functional
Requirement ①Bypass
Prevention
②Interference/
Destruction
Prevention
③Deactivation
Prevention
④Disabling
Detection
FIA_AFL.1[2] N/A FMT_MTD.1[1] FMT_MOF.1[1] N/A
FIA_AFL.1[3] N/A FMT_MTD.1[1] FMT_MOF.1[1] N/A
FIA_AFL.1[4] N/A FMT_MTD.1[1] FMT_MOF.1[1] N/A
FIA_AFL.1[5] N/A FMT_MTD.1[1] FMT_MOF.1[1] N/A
FIA_ATD.1 N/A N/A FMT_MOF.1[1] N/A
FIA_SOS.1[1] N/A N/A FMT_MOF.1[1] N/A
FIA_SOS.1[2] N/A N/A FMT_MOF.1[1] N/A
FIA_SOS.1[3] N/A N/A FMT_MOF.1[1] N/A
FIA_SOS.1[4] N/A N/A FMT_MOF.1[1] N/A
FIA_SOS.1[5] N/A N/A N/A N/A
FIA_SOS.2 N/A N/A N/A N/A
FIA_UAU.2[1] FPT_RVM.1 FMT_MTD.1[5] FMT_MOF.1[1] N/A
FIA_UAU.2[2] FPT_RVM.1
FMT_MTD.1[1]
FMT_MTD.1[3]
FMT_MTD.1[4]
FMT_MTD.1[6]
FMT_MOF.1[1] N/A
FIA_UAU.2[3] FPT_RVM.1
FMT_MTD.1[1]
FMT_MTD.1[4]
FMT_MOF.1[1] N/A
FIA_UAU.2[4] FPT_RVM.1
FMT_MTD.1[2]
FMT_MTD.1[4]
FMT_MOF.1[1] N/A
FIA_UAU.6 N/A N/A FMT_MOF.1[1] N/A
FIA_UAU.7 N/A N/A FMT_MOF.1[1] N/A
FIA_UID.2[1] N/A N/A FMT_MOF.1[1] N/A
FIA_UID.2[2] N/A N/A FMT_MOF.1[1] N/A
FIA_UID.2[3] N/A N/A FMT_MOF.1[1] N/A
FIA_UID.2[4] N/A N/A FMT_MOF.1[1] N/A
FIA_USB.1 N/A N/A FMT_MOF.1[1] N/A
FMT_MOF.1[1] N/A N/A N/A N/A
FMT_MOF.1[2] N/A N/A FMT_MOF.1[1] N/A
FMT_MOF.1[3] N/A N/A N/A N/A
FMT_MSA.3 N/A N/A FMT_MOF.1[1] N/A
FMT_MTD.1[1] N/A N/A FMT_MOF.1[1] N/A
FMT_MTD.1[2] N/A N/A FMT_MOF.1[1] N/A
FMT_MTD.1[3] N/A N/A FMT_MOF.1[1] N/A
FMT_MTD.1[4] N/A N/A FMT_MOF.1[1] N/A
FMT_MTD.1[5] N/A N/A FMT_MOF.1[1] N/A
FMT_MTD.1[6] N/A N/A FMT_MOF.1[1] N/A
FMT_SMF.1 N/A N/A FMT_MOF.1[1] N/A
FMT_SMR.1[1] N/A N/A FMT_MOF.1[1] N/A
FMT_SMR.1[2] N/A N/A FMT_MOF.1[1] N/A
FMT_SMR.1[3] N/A N/A FMT_MOF.1[1] N/A
FPT_RVM.1 N/A N/A FMT_MOF.1[1] N/A
FPT_SEP.1 N/A N/A FMT_MOF.1[1] N/A
FIA_NEW.1 FPT_RVM.1 N/A FMT_MOF.1[1] N/A
FNEW_RIP.1 N/A N/A N/A N/A
FCS_COP.1[E] N/A N/A N/A N/A
FIA_AFL.1[E] N/A N/A N/A N/A
FIA_UAU.2[E] N/A N/A N/A N/A
FIA_UAU.7[E] N/A N/A N/A N/A
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
73 / 90
① Bypass Prevention
＜By-pass prevention of functional requirement that relates to administrator＞
As for FDP_ACF.1[1] that regulates the user box access control, FDP_ACF.1[2] that
regulates the secure print file access control, and FDP_ACF.1[3] that regulates the
administrator mode access control, the by-pass prevention is supported by FIA_UAU.2[2]
that regulates the administrator’s identification and authentication.
Furthermore, because FIA_UAU.2[2] is called by FPT_RVM.1 without fail, the by-pass
prevention is supported.
＜By-pass prevention of functional requirement that relates to service engineer＞
As for FDP_ACF.1[3] that regulates the setting management access control, the by-pass
prevention is supported by FIA_UAU.2[1] that regulates the service engineer’s identification
and authentication.
In addition, FIA_UAU.2[1] is called by FPT_RVM.1 without fail, the by-pass prevention is
supported.
＜By-pass prevention of functional requirement that relates to user box＞
As for FDP_ACF.1[1] that regulates the user box access control, the by-pass prevention is
supported by FIA_UAU.2[4] that authenticates the user is the permitted user to use the
user box.
In addition, because FIA_UAU.2[4] that regulates the authentication of the user who is
permitted the use of the user box are called by FPT_RVM.1 without fail, and so the by-pass
prevention is supported.
＜By-pass prevention of functional requirement that relates to secure print＞
As for FDP_ACF.1[2] that regulates the secure print file access control, the by-pass
prevention is supported by FIA_UAU.2[3] that authenticates the authorized user to use the
secure print file.
In addition, because FIA_UAU.2[3] that regulates the authentication of the authorized user
to use the secure print file are called by FPT_RVM.1 without fail, so that the by-pass
prevention is supported.
＜By-pass prevention of validity verification of HDD＞
FIA_NEW.1 that verifies the validity of HDD is called by FPT_RVM.1 without fail, so that
the by-pass prevention is supported.
② Interference and Destruction Prevention
＜Maintenance of user box access control＞
By FPT_SEP.1, only the subject of two types such as the authenticated administrator who is
assumed by the user box access control and the user who is permitted the use of the
authenticated user box, can operate the user box and the user box file.
With two requirements in the above-mentioned, FDP_ACF.1[1] is supported in the
prevention of interference and destruction from other illegal subject.
＜Maintenance of secure print file access control＞
FPT_SEP.1 permits the operation of the secure print file only to the two types of subject
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
74 / 90
which are the authenticated administrator who is assumed by the secure print file access
control and the user who is permitted the use of authenticated secure print file.
FDP_ACF.1[2] is supported in the interference and destruction prevention from other illegal
subject.
＜Maintenance of setting management access control＞
Only the subject that acts the authenticates administrator who is assumed by the set
management access control and the authenticated service engineer can operate the object
regulated for by the setting management access control by FPT_SEP.1, and the prevention
of an illegal interference and destruction from other illegal subject are supported for
FDP_ACF.1[3].
＜Management of CE password＞
The modification operation of the CE password has been permitted only to the service
engineer by FMT_MTD.1[5]. This supports the prevention of unauthorized interference and
destruction of FIA_UAU.2[1].
＜Management of administrator password＞
The modification operation of the administrator password is permitted only to the
administrator and the service engineer by FMT_MTD.1[3]. The initialization of the
administrator password is permitted only to the administrator and the service engineer by
FMT_MTD.1[6]. This supports the prevention of unauthorized interference and destruction
of FIA_UAU.2[2].
＜Management of SNMP password＞
The modification operation of the SNMP password is permitted to the administrator by
FMT_MTD.1[1]. The inquiry operation is permitted to the administrator by FMT_MTD.1[4],
and the initialization operation is permitted only to the administrator and the service
engineer by FMT_MTD.1[6]. This supports the prevention of unauthorized interference and
destruction of FIA_UAU.2[2].
＜Management of secure print password＞
The inquiry operation is permitted only to the administrator by FMT_MTD.1[4]. The
modification is permitted only to the administrator by FMT_MTD.1[1]. This supports the
prevention of unauthorized interference and destruction of FIA_UAU.2[3].
＜Management of user box password＞
The modification operation is permitted to the administrator and the user who is permitted
the use of the user box by FMT_MTD.1[2]. The inquiry operation is permitted only to the
administrator by FMT_MTD.1[4]. This supports the prevention of unauthorized
interference and destruction of FIA_UAU.2[4].
＜Management of authentication failure frequency threshold＞
The modification operation of the authentication frequency failure threshold which is set in
all the authentication activities such as the service engineer authentication, the
administrator authentication, the secure print authentication, the user box authentication,
and the MIB object access authentication is permitted only to the administrator by
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
75 / 90
FMT_MTD.1[1]. This supports the prevention of unauthorized interference and destruction
of FIA_AFL.1[2], FIA_AFL.1[3], FIA_AFL.1[4], FIA_AFL.1[5].
③ Deactivation Prevention
＜Maintenance of Enhanced Security function＞
FMT_MOF.1[1] permits only to the administrator and the service engineer the operation
setting of the Enhanced Security function. The Enhanced Security function influences all
the TOE security structures except the all area overwrite deletion function executed by the
specified operation of the administrator and quality of session information. This supports
the deactivation prevention of all the security functions achieved by the security
requirements of TOE except FNEW_RIP.1, FIA_SOS/1[5], FIA_SOS.2, FMT_MOF.1[1].
④ Disabling Detection
The requirement that supports the disabling detection doesn’t exist.5
8.2.2. Rational for Minimum Strength of Function
The Printer that is loaded with this TOE is connected to an intra-office LAN with
appropriately controlled connections with external networks. Therefore, there is no possibility
that it is directly attacked by unspecified people via the Internet. As long as it has a strength
level that can counter the threat by users who are users of the TOE and a person who can enter
the office and not user of the TOE as an agent, it is acceptable, as explicitly described in section
3.3. Therefore, this TOE regulates the security objectives by assuming an unskilled attacker and
thus, the selection of the SOF-Basic as the minimum strength of function is reasonable.
8.2.3. Rationale for IT Security Assurance Requirements
This TOE is installed and used in an environment where adequate security is maintained in
terms of the physical, personnel, and connectivity. Nonetheless, adequate effectiveness in the
environment where the TOE is used must be assured. As a general commercial office product,
the execution of tests based on function specifications and high level design, and analysis of the
strength of function and a search for vulnerabilities are required. In addition, it is desirable that
it has a development environment control, a configuration management for the TOE and a
secure distribution procedure. And therefore the selection of EAL3, which provides an adequate
assurance level, is reasonable.
The secure requirement dependency analysis is assumed to be appropriate because the
package EAL has been selected, therefore details are not discussed.
8.2.4. Consistency rationale for the set of IT security functional requirement
The followings show the rationale in which the IT security requirement with a possibility to
compete does not exist.
5
Though this is not shown in the mutual support analysis, FIA_AFL.1 requirement supports respectively against
the attack that aims at the disabling of each authentication function. This is sufficient to maintain the security
objective of this TOE. (This content is specified by the dependency analysis.)
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
76 / 90
＜IT security functional requirement＞
Though several access control policies are set up by repeating the access control requirement
(FDP_ACC.1 etc.), it regulates the access control related to the followings, such as ① user box,
② secure print, ③ Printer addresses. These do not cover each other the same controlled object
by several policies, and so they do not compete each other.
FNEW_RIP.1 is applied as an extended requirement that regulates the deletion of the
protective assets, but the threat concerning the possibility of an unauthorized deletion is not
targeted in this case because of the concept of emphasis on confidentiality. Therefore, the
requirement for the competing data deletion protection has not been selected at all.
The structure, that a competition possibility is suggested, doesn't exist from the relations
between requirements by dependency, correlation by mutual support, and the various analysis
of validity of security functional requirement to TOE security objectives.
＜IT security assurance requirement＞
EAL that is the assurance package is applied. Therefore, it is confirmed that the possibility of
the competition between security assurance requirements doesn't exist regardless of this ST.
8.3. Rational for TOE Summary Specifications
8.3.1. Rational for the TOE Security Functions
8.3.1.1. Necessity
The conformity of the TOE security functions and the TOE security functional requirements
are shown in the following table. It shows that the TOE security functions correspond to at least
one TOE security functional requirement.
Table 13 Conformity of TOE Security Functions to TOE Security Functional Requirements
TOE Security Function
TOE Security
Functional
Requirement
F.ADMIN
F.ADMIN-SNMP
F.SERVICE
F.BOX
F.PRINT
F.OVERWRITE-ALL
F.CRYPT
F.HDD
F.RESET
FCS_CKM.1 ●
FDP_ACC.1[1] ● ●
FDP_ACC.1[2] ● ●
FDP_ACC.1[3] ● ● ●
FDP_ACF.1[1] ● ●
FDP_ACF.1[2] ● ●
FDP_ACF.1[3] ● ● ●
FIA_AFL.1[1] ● ●
FIA_AFL.1[2] ● ●
FIA_AFL.1[3] ● ● ●
FIA_AFL.1[4] ● ● ●
FIA_AFL.1[5] ● ● ●
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
77 / 90
TOE Security Function
TOE Security
Functional
Requirement
F.ADMIN
F.ADMIN-SNMP
F.SERVICE
F.BOX
F.PRINT
F.OVERWRITE-ALL
F.CRYPT
F.HDD
F.RESET
FIA_AFL.1[6] ● ● ● ●
FIA_ATD.1 ● ●
FIA_SOS.1[1] ● ●
FIA_SOS.1[2] ● ●
FIA_SOS.1[3] ●
FIA_SOS.1[4] ● ● ●
FIA_SOS.1[5] ● ●
FIA_SOS.2 ● ●
FIA_UAU.2[1] ●
FIA_UAU.2[2] ● ●
FIA_UAU.2[3] ●
FIA_UAU.2[4] ●
FIA_UAU.6 ● ●
FIA_UAU.7 ● ● ● ●
FIA_UID.2[1] ●
FIA_UID.2[2] ● ●
FIA_UID.2[3] ●
FIA_UID.2[4] ●
FIA_USB.1 ● ●
FMT_MOF.1[1] ● ●
FMT_MOF.1[2] ● ●
FMT_MOF.1[3] ●
FMT_MSA.3 ●
FMT_MTD.1[1] ● ●
FMT_MTD.1[2] ● ●
FMT_MTD.1[3] ● ●
FMT_MTD.1[4] ●
FMT_MTD.1[5] ●
FMT_MTD.1[6] ● ●
FMT_SMF.1 ● ● ● ●
FMT_SMR.1[1] ●
FMT_SMR.1[2] ● ●
FMT_SMR.1[3] ●
FPT_RVM.1 ● ● ● ● ● ●
FPT_SEP.1 ● ● ● ● ●
FNEW_RIP.1 ●
FIA_NEW.1 ●
8.3.1.2. Sufficiency
The TOE security functions for the TOE security functional requirements are described.
FCS_CKM.1
FCS_CKM.1 regulates the various conditions of the encryption key generated along with the
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
78 / 90
encryption of HDD.
F.CRYPT generates the encryption key of 128bit by using Konica Minolta HDD encryption key
generation algorithm (SHA-1).
Accordingly, this functional requirement is satisfied.
FDP_ACC.1[1]
FDP_ACC.1[1] regulates the relationship between the subject controlled to the user box and
the user box file which are the object, and the operation.
F.ADMIN performs the user box access control for the task of acting for the user to back-up
the user box file.
F.BOX performs the user box access control for the task of acting for the user to print a user
box file, mover to other user box, and copy to other user box.
Accordingly, this functional requirement is satisfied.
FDP_ACC.1[2]
FDP_ACC.1[2] regulates the relationship between the subject controlled to the secure print
file that is the object and the operation.
F.ADMIN performs the secure print file access control for the task of substituting the user to
back up the secure print file.
F.PRINT performs the secure print file control for the task of substituting the user to print the
list of secure print file.
Accordingly, this functional requirement is satisfied.
FDP_ACC.1[3]
FDP_ACC.1[3] regulates the relationship between the subjects controlled to the HDD lock
password object, Encryption passphrase object, and Printer address group object which are
the object and the operation.
F.ADMIN performs the setting management access control for the task of substituting the
user to set, back-up and restore the HDD lock password object and encryption passphrase
object. In addition, it performs the setting management access control for the task of
substituting the user to set and restore Printer address group object.
F.ADMIN-SNMP performs the setting management access control for the task of substituting
the user to set Printer address group object.
F.SERVICE performs the setting management access control for the task of substituting the
user to set HDD lock password object and encryption passphrase object.
Accordingly, this functional requirement is satisfied.
FDP_ACF.1[1]
FDP_ACF.1[1] regulates the regulation of relationship between the subject controlled to the
user box file which are an object, and the operation.
F.ADMIN performs the user box access control to which the following rules are applied.
It permits the administrator the back-up operation of the user box file.
F.BOX performs the user box access control to which the following rules are applied.
It permits the user the operation of the user box file in the selected user box such as the
print, the movement and the copy.
Accordingly, this functional requirement is satisfied.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
79 / 90
FDP_ACF.1[2]
FDP_ACF.1[2] regulates the regulation of the relationship between the subject controlled to
the secure print file which is the object, and the operation.
F.ADMIN performs the secure print file access control to which the following rules are
applied.
It permits the administrator the backup operation of the secure print file.
F.PRINT performs the secure print file access control to which the following rules are applied.
It permits the printing operation of the selected secure print file to the user who is allowed
to use the secure print file.
Accordingly, this functional requirement is satisfied.
FDP_ACF.1[3]
FDP_ACF.1[3] regulates the regulation of the relationship between the subject controlled to
the HDD lock password object, the encryption passphrase object and the Printer address
group object that are the object, and the operation.
F.ADMIN performs the setting management access control to which the following rules are
applied.
It permits the administrator the setting, the back-up and the restoration of the HDD lock
password object and the encryption passphrase object.
It permits the administrator the setting and the restoration operations of the Printer
address group object.
F.ADMIN-SNMP performs the secure print file access control to which the following rules are
applied.
It permits the administrator the setting operation of the Printer address group object.
F.SERVICE performs the setting management access control to which the following rules are
applied.
It permits the service engineer the setting operation of the HDD lock password object and
the encryption passphrase object (initialization operation).
Accordingly, this functional requirement is satisfied.
FIA_AFL.1[1]
FIA_AFL.1[1] regulates the action for the authentication failure to the service engineer
authentication. In the service engineer authentication for accessing the service mode or
changing the CE password, when the authentication failure of failure frequency threshold
(1-3 times) that the administrator set is detected, F.SERVICE logs off from the service mode
authentication status and locks the authentication function.
F.RESET releases the lock status by the reboot of TOE by turning OFF and ON the power
supply that clears the times of failure in each authentication function.
Accordingly, this functional requirement is satisfied.
FIA_AFL.1[2]
FIA_AFL.1[2] regulates the action of the authentication failure to the administrator
authentication. In the administrator authentication for accessing the administrator mode or
changing the administrator password, when the authentication failure of failure frequency
threshold (1-3 times) that the administrator set is detected, F.ADMIN logs off from the
authentication status to the administrator mode and locks the authentication function.
F.RESET releases the lock status by the reboot of TOE by turning OFF and ON the power
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
80 / 90
supply that clears the times of failure in each authentication function.
Accordingly, this functional requirement is satisfied.
FIA_AFL.1[3]
FIA_AFL.1[3] regulates the action for the authentication failure to the administrator
authentication when accessing to the MIB object by using SNMP. In the authentication using
the SNMP password for accessing to the MIB object, when the authentication failure of failure
frequency threshold (1-3 times) that the administrator set is detected, F.ADMIN-SNMP
denies the access to the MIB object and locks an authentication function.
F.RESET releases the lock status by the reboot of TOE by turning OFF and ON the power
supply that clears the times of failure in each authentication function.
Accordingly, this functional requirement is satisfied.
FIA_AFL.1[4]
FIA_AFL.1[4] regulates the action for the authentication failure to the authentication of the
user permitted the use of the secure print file.
In the authentication of a user permitted the use of the secure print file, when the
authentication failure of failure frequency threshold (1-3 times) that an administrator sets is
detected, F.PRINT denies the access to the secure print file and locks an authentication
function.
F.RESET releases the lock status by the reboot of TOE by turning OFF and ON the power
supply that clears the times of failure in each authentication function. Moreover, F.ADMIN
releases the lock status by the lock release function that is available in the administrator
mode.
Accordingly, this functional requirement is satisfied.
FIA_AFL.1[5]
FIA_AFL.1[5] regulates the action for the authentication failure to the authentication of the
user permitted the use of the user box.
In the authentication for accessing the user box and changing a user box password, when the
authentication failure of failure frequency threshold (1-3 times) that an administrator sets is
detected, F.BOX denies the access to the user box and locks an authentication function.
F.RESET releases the lock status by the reboot of TOE by turning OFF and ON the power
supply that clears the times of failure in each authentication function. Moreover, F.ADMIN
releases the lock status by the lock release function that is available in the administrator
mode.
Accordingly, this functional requirement is satisfied.
FIA_AFL.1[6]
FIA_AFL.1[6] regulates the action for the authentication failure to the various authentication
on the panel. In the authentication of service engineer for accessing the service mode, when
the authentication failure is detected, F.SERVICE denies all input receipts from a panel.
F.ADMIN rejects all input receipts from a panel when the authentication failure is detected in
the administrator authentication for accessing the administrator mode.
F.BOX rejects all input receipts from a panel when the authentication failure is detected in
the authentication for accessing to the user box from a panel.
F.PRINT rejects all input receipts from a panel when the authentication failure is detected in
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
81 / 90
the authentication of a user permitted the use of the secure print file.
These series of operation is released automatically in five seconds.
Accordingly, this functional requirement is satisfied.
FIA_ATD.1
FIA_ATD.1 regulates the security attribute related by the user.
F.BOX assigns a user box ID to the task of substituting the user.
F.PRINT assigns the secure print internal control ID to the task of substituting the user.
Accordingly, this functional requirement is satisfied.
FIA_SOS.1[1]
FIA_SOS.1[1] regulates the quality of the administrator password and the CE password.
F.ADMIN verifies the quality of the administrator password that is composed of ASCII code
(0x21-0x7E, except 0x22 and 0x2B) in total of 92 characters by eight digits, is not composed of
one kind of character and does not correspond to the value currently set.
F.SERVICE verifies the quality of CE password and the administrator password that is
composed of ASCII code (0x21-0x7E, except 0x22 and 0x2B) in total of 92 characters with
eight digits, is not composed of one kind of characters and does not correspond to the value
currently set.
Accordingly, this functional requirement is satisfied.
FIA_SOS.1[2]
FIA_SOS.1[2] regulates the quality of the SNMP password.
F.ADMIN verifies that the quality of the SNMP password (Privacy password, Authentication
password) is composed of ASCII code (0x20-0x7E) in total of 95 characters by eight or more
digits. F.ADMIN-SNMP also verifies that the quality of the SNMP password (Privacy
password, Authentication password) is composed of ASCII code (0x20-0x7E) in total of 95
characters with eight or more digits.
Accordingly, this functional requirement is satisfied.
FIA_SOS.1[3]
FIA_SOS.1[3] regulates the quality of the HDD lock password and the encryption passphrase.
F.ADMIN verifies that the quality of the HDD lock password and the encryption passphrase is
composed of ASCII code (0x21-0x7E, except 0x22, 0x28, 0x29, 0x2C, 0x3A, 0x3B, 0x3C, 0x3E,
0x5B, 0x5C, 0x5D) in total of 83 characters by 20 digits, and is not composed of one kind of
characters.
Accordingly, this functional requirement is satisfied.
FIA_SOS.1[4]
FIA_SOS.1[4] regulates the quality of the secure print password and the user box password.
F.ADMIN verifies that the quality of the user box password is composed of ASCII code
(0x20-0x7E, except 0x22 and 0x2B) in total of 93 characters by eight digits and is not
composed of one kind of characters.
F.BOX verifies that the quality of the user box password is composed of ASCII code
(0x20-0x7E, except 0x22 and 0x2B) in total of 93 characters by eight digits and is not
composed of one kind of characters.
F.PRINT verifies that the quality of the secure print password is composed of ASCII code
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
82 / 90
(0x20-0x7E, except 0x22 and 0x2B) in total 93 characters by eight digits and is not composed
of one kind of characters.
Accordingly, this functional requirement is satisfied.
FIA_SOS.1[5]
FIA_SOS.1[5] regulates the quality of the session information.
F.ADMIN verifies that a space quality is more than 1010 as the quality of session information.
F.BOX verifies that a space quality is more than 1010 as the quality of session information.
Accordingly, this functional requirement is satisfied.
FIA_SOS.2
FIA_SOS.2 regulates the generation of session information and its quality.
F.ADMIN generates the secrets that are the space quality of 1010 or more to session
information in the administrator authentication.
F.BOX generates the secrets that are the space quality of 1010 or more to session information
in the user box authentication.
Accordingly, this functional requirement is satisfied.
FIA_UAU.2[1]
FIA_UAU.2[1] regulates the authentication of the service engineer.
F.SERVICE authenticates that the user who accesses the service mode by using the CE
password is the service engineer.
Accordingly, this functional requirement is satisfied.
FIA_UAU.2[2]
FIA_UAU.2[2] regulates the authentication of the administrator.
F.ADMIN authenticates that the user who accesses the administrator mode by using the
administrator password is the administrator.
F.ADMIN-SNMP authenticates that the user who accesses the MIB object by using the SNMP
password (Privacy password, Authentication password) is the administrator.
Accordingly, this functional requirement is satisfied.
FIA_UAU.2[3]
FIA_UAU.2[3] regulates the authentication of the authorized user to use the secure print file.
F.PRINT authenticates that the user is the authorized user to use the secure print file by
using the secure print password that is set to each secure print file.
Accordingly, this functional requirement is satisfied.
FIA_UAU.2[4]
FIA_UAU.2[4] regulates the authentication of the authorized user to use the user box.
F.BOX authenticates that the user is the authorized user to use the user box by using the user
box password that is set to each user box.
Accordingly, this functional requirement is satisfied.
FIA_UAU.6
FIA_UAU.6 regulates the re-authentication for the important operation such as changing a
password.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
83 / 90
F.ADMIN re-authenticates the administrator at the operation for the change of the
administrator password. Along with the change operation of the HDD lock password and
encryption passphrase, by collating the registered HDD lock password and registered
encryption passphrase, it re-authenticates the administrator who has known each of
confidential information.
F.SERVICE re-authenticates the service engineer at the operation of the change of the CE
password.
Accordingly, this functional requirement is satisfied.
FIA_UAU.7
FIA_UAU.7 regulates the return of “*" as the feedback under the authentication.
F.ADMIN returns “*" for each character for entered administrator password from the panel in
the authentication and re-authentication of administrator, and prevents a direct display of the
administrator password.
F.SERVICE returns “*" for each character for the entered CE password from the panel in the
authentication and re-authentication of the service engineer, and prevents a direct display of
the CE password.
F.PRINT returns “*" for each character for the entered secure print password from the panel in
the authentication of the authorized user who can use the secure print file, and prevents the
direct display of the secure print password.
F.BOX returns "*" for each character for the entered user box password from the panel in the
authentication of the user who is permitted the use of the public user box, and prevents a
direct display of the user box password.
Accordingly, this functional requirement is satisfied.
FIA_UID.2[1]
FIA_UID.2[1] regulates the identification of the service engineer.
F.SERVICE identifies the user who accesses the service mode is a service engineer.
Accordingly, this functional requirement is satisfied.
FIA_UID.2[2]
FIA_UID.2[2] regulates the authentication of the administrator.
F.ADMIN identifies the user who accesses the administrator mode is an administrator.
F.ADMIN-SNMP identifies the user, who accesses the MIB object, is an administrator.
Accordingly, this functional requirement is satisfied.
FIA_UID.2[3]
FIA_UID.2[3] regulates the identification of the user who is permitted the use of the secure
print file.
F.PRINT identifies a user who is permitted the use of the secure print file by selecting the
secure print file as an operation target.
Accordingly, this functional requirement is satisfied.
FIA_UID.2[4]
FIA_UID.2[4] regulates the identification of the user who is permitted the use of the user box.
F.BOX identifies the user who is permitted the use of the user box by selecting the user box as
the operation target.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
84 / 90
Accordingly, this functional requirement is satisfied.
FIA_USB.1
FIA_USB.1 regulates the security attribute association to subject that substitutes the user.
F.PRINT associates the "secure pint internal control ID" of the concerned secure print file to
the task of substituting the user when authenticated for the access to the secure print file..
F.BOX associates the "User Box ID" of the concerned user box to the task of substituting the
user when authenticated for the access to the user box file.
Accordingly, this functional requirement is satisfied.
FMT_MOF.1[1]
FMT_MOF.1[1] regulates the behavior management of the enhanced security function.
F.ADMIN provides the settings of the enhanced security function in the administrator mode,
and manages the stop operation of the concerned function. In addition, although it is possible
to change the back-up data acquired by back-up operation and to set off the Enhanced
Security function as a result of performing the restoration operation, F.ADMIN limits the
back-up and restoration operation only to the administrator. Although the execution of the
HDD logical format and the overwrite deletion function of all area makes the Enhanced
Security setting invalid, F.ADMIN permits the operation only to the administrator.
F.SERVICE offers the HDD logical format function, HDD physical format function, the HDD
installation setting function and the initialization function to make the Enhanced Security
function invalid in the service mode along with execution and manages the setting-off
operation of the Enhanced Security function.
Accordingly, this functional requirement is satisfied.
FMT_MOF.1[2]
FMT_MOF.1[2] regulates the behavior management of the SNMP password authentication.
F.ADMIN permits the operation of setting function of SNMP password authentication
function in the administrator mode.
F.ADMIN-SNMP permits the administrator who is authenticated by the SNMP password the
setting operation of the SNMP password authentication.
Accordingly, this functional requirement is satisfied.
FMT_MOF.1[3]
FMT_MOF.1[3] regulates the behavior management of the setup function.
F.SERVICE offers the operation setting function of setup function in service mode and
manages the operation function of setup function.
Accordingly, this functional requirement is satisfied.
FMT_MSA.3
FMT_MSA.3 regulates the secure print internal control ID that is set at the time of
registration of secure print file.
F_PRINT grants the secure print internal control ID that is identified uniquely to the
concerned secure print file at the time of registration of secure print file.
Accordingly, this functional requirement is satisfied.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
85 / 90
FMT_MTD.1[1]
FMT_MTD.1[1] regulates the management of a SNMP password, the failure number of times
threshold, and a secure print password.
F.ADMIN permits the operation to change the SNMP password and the setting data of
authentication failure frequency threshold in the administrator mode. In addition, F.ADMIN
permits the administrator the back-up and restoration operation, and so it is possible to
change the back-up data which is acquired by back-up operation, and to change a SNMP
password, the failure number of times threshold and a secure print password as a result of
performing the restoration operation.
F.SNMP-ADMIN permits the change of the SNMP password.
Accordingly, this functional requirement is satisfied.
FMT_MTD.1[2]
FMT_MTD.1[2] regulates the management of the user box password.
F.ADMIN permits the change operation of the user box password that is set to the user box in
the administrator mode. In addition, F.ADMIN permits the administrator the back-up and
restoration operation, and so it is possible to change the back-up data which is acquired by
back-up operation, and to change the user box password as a result of performing the
restoration operation.
F.BOX permits the change operation of the user box password to the authenticated user as the
user who is permitted the use of the user box concerned.
Accordingly, this functional requirement is satisfied.
FMT_MTD.1[3]
FMT_MTD.1[3] regulates the management of the administrator password.
F.ADMIN permits the change operation of the administrator password in the administrator
mode.
F.SERVICE permits the change operation of the administrator password in the service mode.
Accordingly, this functional requirement is satisfied.
FMT_MTD.1[4]
FMT_MTD.1[4] regulates the management of the SNMP password, the User box password
and the Secure Print password.
F.ADMIN permits the administrator the back-up and restoration operation, and so it is
possible to browse the SNMP password, the User box password and the Secure Print password
by means of the back-up data which is acquired by back-up operation.
Accordingly, this functional requirement is satisfied.
FMT_MTD.1[5]
FMT_MTD.1[5] regulates the management of the CE password.
F.SERVICE permits the change operation of the CE password in the service mode.
Accordingly, this functional requirement is satisfied.
FMT_MTD.1[6]
FMT_MTD.1[6] regulates the management of the administrator password and the SNMP
password.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
86 / 90
F.ADMIN permits the initialization operation of the administrator password and the SNMP
password, that is performed along with the execution of the overwrite deletion operation of all
area in the administrator mode.
F.SERVICE permits the initialization operation of the administrator password and the SNMP
password, which is performed along with the execution of the initializing function in the
service mode.
Accordingly, this functional requirement is satisfied.
FMT_SMF.1
FMT_SMF.1 specifies the security management function.
F.ADMIN provides the following security management functions.
Setting function of authentication failure frequency threshold
Back-up and restoration function
It consequentially corresponds to the inquiry function of the following TSF data.
・SNMP password
・User box password
・Secure Print password
It also corresponds to the modification function of the following TSF data.
・SNMP password
・User box password
・Secure print password
・Operational setting data of the Enhanced Security function
・Authentication failure frequency threshold of the authentication operation prohibited
function
Stop function of the Enhanced Security function
・Operational setting function of the Enhanced Security function
・HDD logical format function
Modification function of the administrator password
Modification function of the user box password
Modification function of the SNMP password (Privacy password and Authentication
password）
Lock release function
This offers the following authentication functions.
・Authentication function in the access to the MIB object
・Authentication function in the access to the user box
・Authentication function in the access to the secure print
F.ADMIN-SNMP offers security management functions.
Modification function of the SNMP password (Privacy password and Authentication
password）
Operational setting function of the SNMP password authentication function
F.SERVICE offers the following security management functions.
Modification function of the CE password
Modification function of the administrator password
Operation setting function of setup function
Initialization function of the administrator password
・Initialization function
Initialization function of the SNMP password (Privacy password and Authentication
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
87 / 90
password）
・Initialization function
Stop function of the Enhanced Security function
・HDD logical format function
・HDD physical format function
・HDD installation setting function
・Initialization function
F.BOX offers the following security management functions.
Modification function of the user box password
F.ADMIN offers the following security management functions.
Stop function of the Enhanced Security function
・Overwrite deletion function of all area
Initialization of the administrator password
・Overwrite deletion function of all area
Initialization of the SNMP password (Privacy password and Authentication password）
・Overwrite deletion function of all area
Accordingly, this functional requirement is satisfied.
FMT_SMR.1[1]
FMT_SMR.1[1] regulates the role as the service engineer.
F.SERVICE recognizes the user who is authenticated by the CE password as a service
engineer.
Accordingly, this functional requirement is satisfied.
FMT_SMR.1[2]
FMT_SMR.1[2] regulates the role as an administrator.
F.ADMIN recognizes the user who is authenticated by the administrator password as an
administrator.
F.ADMIN-SNMP recognizes the user who is authenticated by the SNMP password（Privacy
password and Authentication password）as an administrator.
Accordingly, this functional requirement is satisfied.
FMT_SMR.1[3]
FMT_SMR.1[3] regulates the role as a user who is permitted the use of the user box.
F.BOX recognizes the user who is authenticated by the user box password as the authorized
user who can use the user box.
Accordingly, this functional requirement is satisfied.
FPT_RVM.1
FPT_RVM.1 regulates to support that a corresponding TSP execution function must be called
before each TOE security function is permitted to start its operation.
F.ADMIN definitely activates "Administrator authentication function" of which performance
is indispensable, before the use of various functions that can be performed only by
administrator is permitted.
F.ADMIN-SNMP definitely activates "Administrator authentication function" of which
performance is indispensable, before the use of network functions that can be performed only
by administrator is permitted.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
88 / 90
F.SERVICE definitely activates "Service engineer authentication function" of which
performance is indispensable, before the use of various functions that can be performed only
by the service engineer is permitted.
F.BOX definitely activates "Authentication function by the user box password" of which
performance is indispensable, before the use of various functions that can be performed only
by the authorized user who can use the user box is permitted.
F.PRINT definitely activates "Authentication function by the secure print password" of which
performance is indispensable, before the use of various functions that can be performed only
by the authorized user who can use the secure print is permitted.
F.HDD definitely activates "Validity verification function of HDD" of which performance is
indispensable, before writing HDD is permitted when HDD lock function is activated.
Accordingly, this functional requirement is satisfied.
FPT_SEP.1
FPT_SEP.1 regulates maintaining of security domains for protecting against interference and
tampering by subjects who cannot be trusted and regulates separating of security domains of
subjects.
F.ADMIN maintains the administrator authentication domain that is provided various
functions permitted to operate only by administrator, and it does not permit the interference
by the unauthorized subject.
F.ADMIN-SNMP maintains the administrator authentication domain that is provided various
functions permitted to operate only by the administrator who is authenticated with the SNMP
password, and it doesn't permit the interference by the unauthorized subjects.
F.BOX maintains the user box authentication domain that is provided various functions
permitted to operate only by the authorized user who can use the user box by the
authentication of the user box password, and it doesn't allow the interference by the
unauthorized subject.
F.PRINT maintains the secure print file authentication domain that is provided various
functions permitted to operate only by a user who is permitted to use the secure print file by
the authentication of the secure print password, and it doesn't allow the interference by the
unauthorized subject.
F.SERVICE maintains the service engineer authentication domain that is provided various
functions permitted to operate only by the service engineer, and it doesn't allow the
interference by the unauthorized subject.
Accordingly, this functional requirement is satisfied.
FNEW_RIP.1
FNEW_RIP.1 regulates that the object and the TSF data, that are targeted in the explicit
deletion operation can not be restored.
F.OVERWRITE-ALL deletes the user box file, the secure print file, the on-memory image file,
the stored image file, the remaining image file, the image related file, the user box password,
the secure print password and the remaining TSF data by performing the overwrite deletion
to all area of HDD by means of the specified method of overwrite deletion.
In addition, it initializes the NVRAM administrator password and the SNMP password, and
sets OFF the operations of the HDD lock function and the Encryption function.
Accordingly, this functional requirement is satisfied.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
89 / 90
FIA_NEW.1
FIA_NEW.1 regulates the user identification before TSF takes any action to the user.
F.HDD provides the function to check the HDD status if HDD lock password is set, and if the
HDD lock password is not set, it doesn't perform the process of writing and reading to HDD.
Accordingly, this functional requirement is satisfied.
8.3.2. Rational for TOE Security Strength of Function
The TOE security functions having a probabilistic/permutational mechanism are as follows.
① Administrator authentication mechanism offered by F.ADMIN
② CE authentication mechanism offered by F.SERVICE
③ Secure print authentication mechanism offered by F.PRINT
④ User box authentication mechanism offered by F.BOX
⑤ SNMP authentication mechanism offered by F.ADMIN-SNMP
⑥ HDD Lock password collation mechanism offered by F.ADMIN
⑦ Encryption Passphrase collation mechanism offered by F.ADMIN
It used the password composed from ①&② an 8-digits and 92 kinds of character, ③＆④ an
8-digits and 93 kinds of character, ⑤ an 8-digits and 95 kinds of character, and ⑥&⑦ an
20-digits and 83 kinds of character. Among these, ①〜⑤ locks the authentication function by
the continuous three times of authentication failure by operating the authentication operation
prohibition function.
The ① and ④ use the session information secretly in access via network. The secrets use the
value of 1010 or more that is generated by TOE. Moreover, it uses the session information with
the value of 1010 or more that is given externally.
Accordingly, as claimed in Section 6.2, the strength of function of mechanisms adequately
satisfies the SOF-Basis, and it is consistent with the minimum strength of function: SOF-Basic
that is claimed for the TOE security functional requirement for the security strength of function,
stipulated in item 5.1.2.
8.3.3. Mutually Supported TOE Security Functions
The TOE security functional requirements that are satisfied by a combination of IT security
functions that are identifies in the TOE summary specifications, are as shown in the text
regarding the rationale in the section of 8.3.1.
8.3.4. Rationale for Assurance Measures
The required document for the evaluation assurance level EAL3 is covered by the reference
document shown in the assurance measures described in Section 6.4. The TOE security
assurance requirements are satisfied through development, test condition, vulnerability analysis,
the development environment control, configuration management, life cycle management, and
delivery procedures in accordance with the document provided as the assurance measures, as
well as the preparation of a proper guidance document.
bizhub C450P / ineo
+
450P Control Software, Security Target
Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., All Rights Reserved.
90 / 90
8.4. PP calims rationale
There is no PP that is referenced by this ST.