BSI-DSZ-CC-1042-V2-2023
for
DERMALOG Fingerprint PAD Kit LF10
LF10, Part No. 8004-0009-00 or Part No. 8004-0003-05
DermalogBPLF10Plugin, V 1.12.5.2228
DermalogFakeFingerDetectionLF10Plugin, V 1.6.8.2227
DermalogFourprintSegmentation2, V 1.20.2.2210
DermalogAuditLogger, V 1.1.3.1827
from
DERMALOG Identification Systems GmbH
BSI - Bundesamt für Sicherheit in der Informationstechnik, Postfach 20 03 63, D-53133 Bonn
Phone +49 (0)228 99 9582-0, Fax +49 (0)228 9582-5477, Infoline +49 (0)228 99 9582-111
Certification Report V1.0 CC-Zert-327 V5.45
BSI-DSZ-CC-1042-V2-2023 (*)
Presentation Attack Detection System
DERMALOG Fingerprint PAD Kit LF10
Hardware: LF10, Part No. 8004-0009-00 or Part No. 8004-0003-05
Software: DermalogBPLF10Plugin, V 1.12.5.2228
DermalogFakeFingerDetectionLF10Plugin, V 1.6.8.2227
DermalogFourprintSegmentation2, V 1.20.2.2210
DermalogAuditLogger, V 1.1.3.1827
from DERMALOG Identification Systems GmbH
PP Conformance: Fingerprint Spoof Detection Protection Profile based on
Organisational Security Policies (FSDPP_OSP), Version 1.7,
27 November 2009, BSI-CC-PP-0062-2010
Functionality: PP conformant
Common Criteria Part 2 extended
Assurance: Common Criteria Part 3 conformant
ADV_ARC.1, ADV_FSP.2, ADV_TDS.1, AGD_OPE.1,
AGD_PRE.1, ALC_CMC.2, ALC_CMS.2, ALC_DEL.1,
ALC_FLR.1, ASE_CCL.1, ASE_ECD.1, ASE_INT.1,
ASE_OBJ.2, ASE_REQ.2, ASE_SPD.1, ASE_TSS.1,
ATE_COV.1, ATE_FUN.1, ATE_IND.2
The IT Product identified in this certificate has been evaluated at an approved evaluation
facility using the Common Methodology for IT Security Evaluation (CEM), Version 3.1
extended by TOE type specific methodology as listed in the Certification Report for
conformance to the Common Criteria for IT Security Evaluation (CC), Version 3.1. CC and
CEM are also published as ISO/IEC 15408 and ISO/IEC 18045.
(*) This certificate applies only to the specific version and release of the product in its
evaluated configuration and in conjunction with the complete Certification Report and
Notification. For details on the validity see Certification Report part A chapter 5.
The evaluation has been conducted in accordance with the provisions of the certification
scheme of the German Federal Office for Information Security (BSI) and the conclusions of
the evaluation facility in the evaluation technical report are consistent with the
evidence adduced.
This certificate is not an endorsement of the IT Product by the Federal Office for Information
Security or any other organisation that recognises or gives effect to this certificate, and no
warranty of the IT Product by the Federal Office for Information Security or any other
organisation that recognises or gives effect to this certificate, is either expressed or implied.
Bonn, 3 March 2023
For the Federal Office for Information Security
Sandro Amendola L.S.
Head of Division
Bundesamt für Sicherheit in der Informationstechnik
Godesberger Allee 185-189 - D-53175 Bonn - Postfach 20 03 63 - D-53133 Bonn
Phone +49 (0)228 99 9582-0 - Fax +49 (0)228 9582-5477 - Infoline +49 (0)228 99 9582-111
SOGIS
Recognition Agreement
Common Criteria
Recognition Arrangement
Certification Report BSI-DSZ-CC-1042-V2-2023
This page is intentionally left blank.
4 / 20
BSI-DSZ-CC-1042-V2-2023 Certification Report
Contents
A. Certification......................................................................................................................6
1. Preliminary Remarks....................................................................................................6
2. Specifications of the Certification Procedure...............................................................6
3. Recognition Agreements..............................................................................................7
4. Performance of Evaluation and Certification................................................................8
5. Validity of the Certification Result.................................................................................8
6. Publication....................................................................................................................9
B. Certification Results.......................................................................................................10
1. Executive Summary....................................................................................................11
2. Identification of the TOE.............................................................................................12
3. Security Policy............................................................................................................13
4. Assumptions and Clarification of Scope.....................................................................13
5. Architectural Information.............................................................................................13
6. Documentation...........................................................................................................14
7. IT Product Testing.......................................................................................................14
8. Evaluated Configuration.............................................................................................15
9. Results of the Evaluation............................................................................................15
10. Obligations and Notes for the Usage of the TOE.....................................................16
11. Security Target..........................................................................................................16
12. Definitions.................................................................................................................16
13. Bibliography..............................................................................................................18
C. Excerpts from the Criteria..............................................................................................19
D. Annexes.........................................................................................................................20
5 / 20
Certification Report BSI-DSZ-CC-1042-V2-2023
A. Certification
1. Preliminary Remarks
Under the BSIG1
Act, the Federal Office for Information Security (BSI) has the task of
issuing certificates for information technology products.
Certification of a product is carried out on the instigation of the vendor or a distributor,
hereinafter called the sponsor.
A part of the procedure is the technical examination (evaluation) of the product according
to the security criteria published by the BSI or generally recognised security criteria.
The evaluation is normally carried out by an evaluation facility recognised by the BSI or by
BSI itself.
The result of the certification procedure is the present Certification Report. This report
contains among others the certificate (summarised assessment) and the detailed
Certification Results.
The Certification Results contain the technical description of the security functionality of
the certified product, the details of the evaluation (strength and weaknesses) and
instructions for the user.
2. Specifications of the Certification Procedure
The certification body conducts the procedure according to the criteria laid down in the
following:
● Act on the Federal Office for Information Security1
● BSI Certification and Approval Ordinance2
● BMI Regulations on Ex-parte Costs 3
● Special decrees issued by the Bundesministerium des Innern und für Heimat (Federal
Ministry of the Interior and Community)
● DIN EN ISO/IEC 17065 standard
● BSI certification: Scheme documentation describing the certification process (CC-
Produkte) [3]
● BSI certification: Scheme documentation on requirements for the Evaluation Facility, its
approval and licencing process (CC-Stellen) [3]
● Common Criteria for IT Security Evaluation (CC), Version 3.14
[1] also published as
ISO/IEC 15408
● Common Methodology for IT Security Evaluation (CEM), Version 3.1 [2] also published
as ISO/IEC 18045
● BSI certification: Application Notes and Interpretation of the Scheme (AIS) [4]
1
Act on the Federal Office for Information Security (BSI-Gesetz - BSIG) of 14 August 2009,
Bundesgesetzblatt I p. 2821
2
Ordinance on the Procedure for Issuance of Security Certificates and approval by the Federal Office for
Information Security (BSI-Zertifizierungs- und -Anerkennungsverordnung - BSIZertV) of 17 December
2014, Bundesgesetzblatt 2014, part I, no. 61, p. 2231
3
BMI Regulations on Ex-parte Costs - Besondere Gebührenverordnung des BMI für individuell
zurechenbare öffentliche Leistungen in dessen Zuständigkeitsbereich (BMIBGebV), Abschnitt 7 (BSI-
Gesetz) - dated 2 September 2019, Bundesgesetzblatt I p. 1365
4
Proclamation of the Bundesministerium des Innern und für Heimat of 12 February 2007 in the
Bundesanzeiger dated 23 February 2007, p. 3730
6 / 20
BSI-DSZ-CC-1042-V2-2023 Certification Report
3. Recognition Agreements
In order to avoid multiple certification of the same product in different countries a mutual
recognition of IT security certificates - as far as such certificates are based on ITSEC or
CC - under certain conditions was agreed.
3.1. European Recognition of CC – Certificates (SOGIS-MRA)
The SOGIS-Mutual Recognition Agreement (SOGIS-MRA) Version 3 became effective in
April 2010. It defines the recognition of certificates for IT-Products at a basic recognition
level and, in addition, at higher recognition levels for IT-Products related to certain SOGIS
Technical Domains only.
The basic recognition level includes Common Criteria (CC) Evaluation Assurance Levels
EAL 1 to EAL 4. For "Smartcards and similar devices" a SOGIS Technical Domain is in
place. For "HW Devices with Security Boxes" a SOGIS Technical Domain is in place, too.
In addition, certificates issued for Protection Profiles based on Common Criteria are part of
the recognition agreement.
The current list of signatory nations and approved certification schemes, details on
recognition, and the history of the agreement can be seen on the website at
https://www.sogis.eu.
The SOGIS-MRA logo printed on the certificate indicates that it is recognised under the
terms of this agreement by the related bodies of the signatory nations. A disclaimer
beneath the logo indicates the specific scope of recognition.
This certificate is recognized under SOGIS-MRA for all assurance components selected.
3.2. International Recognition of CC – Certificates (CCRA)
The international arrangement on the mutual recognition of certificates based on the CC
(Common Criteria Recognition Arrangement, CCRA-2014) has been ratified on 08
September 2014. It covers CC certificates based on collaborative Protection Profiles (cPP)
(exact use), CC certificates based on assurance components up to and including EAL 2 or
the assurance family Flaw Remediation (ALC_FLR) and CC certificates for Protection
Profiles and for collaborative Protection Profiles (cPP).
The current list of signatory nations and approved certification schemes can be seen on
the website: https://www.commoncriteriaportal.org.
The Common Criteria Recognition Arrangement logo printed on the certificate indicates
that this certification is recognised under the terms of this agreement by the related bodies
of the signatory nations. A disclaimer beneath the logo indicates the specific scope of
recognition.
This certificate is recognized under CCRA-2014 for all assurance components selected.
7 / 20
Certification Report BSI-DSZ-CC-1042-V2-2023
4. Performance of Evaluation and Certification
The certification body monitors each individual evaluation to ensure a uniform procedure, a
uniform interpretation of the criteria and uniform ratings.
The product DERMALOG Fingerprint PAD Kit LF10 has undergone the certification
procedure at BSI. This is a re-certification based on BSI-DSZ-CC-1042-2020. Specific
results from the evaluation process BSI-DSZ-CC-1042-2020 were re-used.
The evaluation of the product DERMALOG Fingerprint PAD Kit LF10 was conducted by
TÜV Informationstechnik GmbH. The evaluation was completed on 20 December 2022.
TÜV Informationstechnik GmbH is an evaluation facility (ITSEF)5
recognised by the
certification body of BSI.
For this certification procedure the sponsor and applicant is: DERMALOG Identification
Systems GmbH.
The product was developed by: DERMALOG Identification Systems GmbH.
The certification is concluded with the comparability check and the production of this
Certification Report. This work was completed by the BSI.
5. Validity of the Certification Result
This Certification Report applies only to the version of the product as indicated. The
confirmed assurance package is valid on the condition that
● all stipulations regarding generation, configuration and operation, as given in the
following report, are observed,
● the product is operated in the environment described, as specified in the following report
and in the Security Target.
For the meaning of the assurance components and assurance levels please refer to CC
itself. Detailed references are listed in part C of this report.
The Certificate issued confirms the assurance of the product claimed in the Security Target
at the date of certification. As attack methods evolve over time, the resistance of the
certified version of the product against new attack methods needs to be re-assessed.
Therefore, the sponsor should apply for the certified product being monitored within the
assurance continuity program of the BSI Certification Scheme (e.g. by a re-assessment or
re-certification). Specifically, if results of the certification are used in subsequent evaluation
and certification procedures, in a system integration process or if a user's risk
management needs regularly updated results, it is recommended to perform a re-
assessment on a regular e.g. annual basis.
In order to avoid an indefinite usage of the certificate when evolved attack methods would
require a re-assessment of the products resistance to state of the art attack methods, the
maximum validity of the certificate has been limited. The certificate issued on 3 March
2023 is valid until 2 March 2028. Validity can be re-newed by re-certification.
The owner of the certificate is obliged:
5
Information Technology Security Evaluation Facility
8 / 20
BSI-DSZ-CC-1042-V2-2023 Certification Report
1. when advertising the certificate or the fact of the product's certification, to refer to
the Certification Report as well as to provide the Certification Report, the Security
Target and user guidance documentation mentioned herein to any customer of the
product for the application and usage of the certified product,
2. to inform the Certification Body at BSI immediately about vulnerabilities of the
product that have been identified by the developer or any third party after issuance
of the certificate,
3. to inform the Certification Body at BSI immediately in the case that security relevant
changes in the evaluated life cycle, e.g. related to development and production sites
or processes, occur, or the confidentiality of documentation and information related
to the Target of Evaluation (TOE) or resulting from the evaluation and certification
procedure where the certification of the product has assumed this confidentiality
being maintained, is not given any longer. In particular, prior to the dissemination of
confidential documentation and information related to the TOE or resulting from the
evaluation and certification procedure that do not belong to the deliverables
according to the Certification Report part B, or for those where no dissemination
rules have been agreed on, to third parties, the Certification Body at BSI has to be
informed.
In case of changes to the certified version of the product, the validity can be extended to
the new versions and releases, provided the sponsor applies for assurance continuity (i.e.
re-certification or maintenance) of the modified product, in accordance with the procedural
requirements, and the evaluation does not reveal any security deficiencies.
6. Publication
The product DERMALOG Fingerprint PAD Kit LF10 has been included in the BSI list of
certified products, which is published regularly (see also Internet: https://www.bsi.bund.de
and [5]). Further information can be obtained from BSI-Infoline +49 228 9582-111.
Further copies of this Certification Report can be requested from the developer6
of the
product. The Certification Report may also be obtained in electronic form at the internet
address stated above.
6
DERMALOG Identification Systems GmbH
Mittelweg 120
20148 Hamburg
Deutschland
9 / 20
Certification Report BSI-DSZ-CC-1042-V2-2023
B. Certification Results
The following results represent a summary of
● the Security Target of the sponsor for the Target of Evaluation,
● the relevant evaluation results from the evaluation facility, and
● complementary notes and stipulations of the certification body.
10 / 20
BSI-DSZ-CC-1042-V2-2023 Certification Report
1. Executive Summary
The Target of Evaluation (TOE) is the DERMALOG Fingerprint PAD Kit LF10 consisting of
a fingerprint sensor (LF10, Part No. 8004-0009-00 or Part No. 8004-0003-05) and PC
software (DermalogBPLF10Plugin, V 1.12.5.2228, DermalogFakeFingerDetectionLF10
Plugin, V 1.6.8.2227, DermalogFourprintSegmentation2, V 1.20.2.2210, DermalogAudit
Logger, V 1.1.3.1827).
Its core functionality is classifying whether a finger that is presented to the sensor, is
actually a real finger presented by a genuine user or whether an artefact is presented (a
so-called artefact presentation or presentation attack).
The Security Target [6] is the basis for this certification. It is based on the certified
Fingerprint Spoof Detection Protection Profile based on Organisational Security Policies
(FSDPP_OSP), Version 1.7, 27 November 2009, BSI-CC-PP-0062-2010 [8].
The TOE Security Assurance Requirements (SAR) are based entirely on the assurance
components defined in Part 3 of the Common Criteria (see part C or [1], Part 3 for details).
The TOE meets the assurance requirements ADV_ARC.1, ADV_FSP.2, ADV_TDS.1,
AGD_OPE.1, AGD_PRE.1, ALC_CMC.2, ALC_CMS.2, ALC_DEL.1, ALC_FLR.1,
ASE_CCL.1, ASE_ECD.1, ASE_INT.1, ASE_OBJ.2, ASE_REQ.2, ASE_SPD.1,
ASE_TSS.1, ATE_COV.1, ATE_FUN.1, ATE_IND.2.
This explicitly defined assurance package is based on EAL 2, but the AVA_VAN
component is completely omitted. It was defined in the PP [8] to focus on application cases
for which it is sufficient to determine whether the Security Functionality claimed by a TOE
is working correctly without performing a dedicated vulnerability assessment.
The TOE Security Functional Requirements (SFR) relevant for the TOE are outlined in the
Security Target [6], chapter 7.1. They are selected from Common Criteria Part 2 and one of
them is newly defined. Thus the TOE is CC Part 2 extended.
The TOE Security Functional Requirements are implemented by the following TOE
Security Functionality:
TOE Security Functionality Addressed issue
SF.AUDIT Security Audit
SF.RIP Residual Information Protection
SF.SM Security Management
SF.PAD Presentation Attack Detection (PAD)
Table 1: TOE Security Functionalities
For more details please refer to the Security Target [6], chapter 8.
The assets to be protected by the TOE are defined in the Security Target [6], chapter 4.2 .
Based on these assets the TOE Security Problem is defined in terms of Assumptions and
Organisational Security Policies. This is outlined in the Security Target [6], chapters 4.3
and 4.5.
This certification covers the configurations of the TOE as outlined in chapter 8.
The vulnerability assessment results as stated within this certificate do not include a rating
for those cryptographic algorithms and their implementation suitable for encryption and
decryption (see BSIG Section 9, Para. 4, Clause 2).
11 / 20
Certification Report BSI-DSZ-CC-1042-V2-2023
The certification results only apply to the version of the product indicated in the certificate
and on the condition that all the stipulations are kept as detailed in this Certification
Report. This certificate is not an endorsement of the IT product by the Federal Office for
Information Security (BSI) or any other organisation that recognises or gives effect to this
certificate, and no warranty of the IT product by BSI or any other organisation that
recognises or gives effect to this certificate, is either expressed or implied.
2. Identification of the TOE
The Target of Evaluation (TOE) is called:
DERMALOG Fingerprint PAD Kit LF10
It consists a fingerprint sensor (LF10, Part No. 8004-0009-00 or Part No. 8004-0003-05)
and PC software (DermalogBPLF10Plugin, V 1.12.5.2228, DermalogFakeFingerDetection
LF10Plugin, V 1.6.8.2227, DermalogFourprintSegmentation2, V 1.20.2.2210, Dermalog
AuditLogger, V 1.1.3.1827).
The following table outlines the TOE deliverables:
No Type Identifier Release Form of Delivery
1 HW LF10 hardware Part No. 8004-0009-00
or
Part No. 8004-0003-05
Parcel mail
2 SW DermalogBPLF10Plugin 1.12.5.2228 Download from
support portal
3 SW DermalogFakeFingerDetectionLF10Plugin 1.6.8.2227 Download from
support portal
4 SW DermalogFourprintSegmentation2 1.20.2.2210 Download from
support portal
5 SW DermalogAuditLogger 1.1.3.1827 Download from
support portal
6 DOC DERMALOG Guidance Addendum
Dermalog Fingerprint PAD Kit LF10 [12]
3.0 Download from
support portal
7 DOC DERMALOG Fingerprint Scanner LF10
User Guide [13]
3.9 Download from
support portal
8 DOC DermalogBPLF10Plugin [14] SHA-256-Hash:
70a6c71b7dc2a9a7d40
93daa59fb92a7155947
8a3ebcbeabea942dd91
ddcf89b
Download from
support portal
Table 2: Deliverables of the TOE
The delivery of the hardware part (fingerprint sensor) is performed via parcel mail including
tracking information. The delivery process starts at the premises of the manufacturer and
is directed directly to the end customer.
As soon as the box arrives at the premises of the customer, the administrator of the device
(who received the guidance documentation via an independent channel, namely the
support portal) is advised to perform an integrity check of the sensor which includes an
inspection of the body of the sensor for any visible manipulations and a check of the seal
that is placed on the bottom of the device.
12 / 20
BSI-DSZ-CC-1042-V2-2023 Certification Report
The TOE software parts and the guidance documentation can be downloaded from the
access controlled support portal of the developer via https connection. The binaries of the
TOE are delivered as part of the installer of the DERMALOGMultiScannerSDK. The
integrity check of the software and the guidance documentation is performed using digital
signatures.
The TOE software offers a function that allows checking the version information of the TOE
components. This function is called FFDGetVersionA and its use is described in the
guidance documentation [12].
The sensor components carry version information on the sticker on their back side. It is
important that this version information (in form of the Part No.) is checked to match the
values listed in table 2 above.
3. Security Policy
The Security Policy is expressed by the set of Security Functional Requirements and
implemented by the TOE. It covers the following issues: security audit, residual information
protection, security management and presentation attack detection.
4. Assumptions and Clarification of Scope
The Assumptions defined in the Security Target and some aspects of Organisational
Security Policies are not covered by the TOE itself. These aspects lead to specific security
objectives to be fulfilled by the TOE-Environment. The following topics are of relevance:
Well trained and trustworthy TOE administrators, physical protection of the TOE,
supporting mechanisms provided by the underlying platform and invocation of the TOE’s
Security Functionality by the protected biometric system.
Details can be found in the Security Target [6], chapter 5.2.
5. Architectural Information
The TOE consists of a HW-subsystem (Scanner) and three SW-subsystems (Scanner
Control API, Supportive API, Presentation Attack Detection API). All four subsystems
together implement the TOE Security Functionality.
The Scanner subsystem provides the interface to the user and captures the fingerprint of
the user.
The Presentation Attack Detection API subsystem implements the core functionality of the
TOE, i.e. the presentation attack detection. This subsystem analyses images of
fingerprints and returns information on how likely these images show a presentation
attack.
The Scanner Control API subsystem implements all functionality that invokes sensor
communication and provides the interface between the TOE SW parts and the sensor.
This subsystem is also responsible for the final decision on PAD, i.e. it compares the
calculated value by the Presentation Attack Detection API subsystem with the threshold
setting and converts it into a binary value.
The Supportive API subsystem implements parts of the TOE’s audit functionality and
provides the interface to the external audit storage. It also provides the functionality to
segment fingerprint images into images of single fingerprints out of an image that contains
up to four fingerprints.
13 / 20
Certification Report BSI-DSZ-CC-1042-V2-2023
6. Documentation
The evaluated documentation as outlined in table 2 is being provided with the product to
the customer. This documentation contains the required information for secure usage of
the TOE in accordance with the Security Target.
Additional obligations and notes for secure usage of the TOE as outlined in chapter 10 of
this report have to be followed.
7. IT Product Testing
7.1. Functional Developer Testing
All developer tests in the context of the evaluation were conducted using the final version
of the TOE. The TOE was configured using a PAD threshold of 50 (FDD_Threshold) and
FDD_Mode 1 and 3 for all tests.
The tests of the audit and management functionality were performed with log level
verbose.
The developer used two simple test tools to test the management, audit and residual
information protection functionality.
The testing of the PAD functionality (according to FPT_SPOD.1) was conducted by
creating artefacts from different materials according to the requirements from the Toolbox
documentation [10]. In total, the developer created 208 artefacts (104 artefacts for each
FFD_Mode) and applied each artefact at least 10 times to the TOE. The test results
showed that no artefact was detected as a real finger in any attempt.
All in all, the developer tested the TOE systematically at the level of TSFI as given in the
Functional Specification. The developer thereby followed the strategy to cover all TSFI.
All tests were passed successfully.
7.2. Independent Evaluator Testing
The evaluator repeated all developer tests, except the test of the presentation attack
detection, in order to verify the adequateness of the tests and the different test tools used
by the developer.
The evaluator further developed a set of own manual test cases for functional testing.
Thereby he had chosen the approach to cover SF from all the functional areas of the TOE
(PAD, Audit, and Management). This approach extends the one used for the developer
tests. Full TSFI coverage is provided in both approaches. The evaluator devised and
performed 2 functional tests and 3 other tests.
For PAD testing, the evaluator created and tested for each FFD_Mode 56 artefacts of
various materials according to the requirements of the Toolbox documentation [10]. The
evaluator carried out more than 1900 attempts to spoof the TOE with these artefacts.
All tests were passed successfully.
14 / 20
BSI-DSZ-CC-1042-V2-2023 Certification Report
8. Evaluated Configuration
This certification covers the following configurations of the TOE:
● Hardware: Part No. 8004-0009-00 or 8004-0003-05, both in FFD_Mode 1 or 3
● Software as described in Table 2
● The TOE has to be used with FFD_Threshold 50.
● As described in the guidance [12], chapter 5.3 the plain finger mode has to used.
9. Results of the Evaluation
9.1. CC specific results
The Evaluation Technical Report (ETR) [7] was provided by the ITSEF according to the
Common Criteria [1], the Methodology [2], the requirements of the Scheme [3] and all
interpretations and guidelines of the Scheme (AIS) [4] as relevant for the TOE.
The Evaluation Methodology CEM [2] was used, extended by guidance specific for the
technology of the product.
The following guidance specific for the technology was used:
(i) Fingerprint Spoof Detection Evaluation Guidance [9]
(ii) Toolbox documentation [10].
As a result of the evaluation the verdict PASS is confirmed for the following assurance
components:
● All components claimed in the Security Target [6], chapter 7.2 and defined in the CC
(see also part C of this report)
As the evaluation work performed for this certification procedure was carried out as a re-
evaluation based on the certificate BSI-DSZ-CC-1042-2020, re-use of specific evaluation
tasks was possible. The focus of this re-evaluation was on the added hardware variant and
on minor software improvements. Especially the PAD tests were performed on both
hardware variants, each operated in both FDD_Modes.
The evaluation has confirmed:
● PP Conformance: Fingerprint Spoof Detection Protection Profile based on
Organisational Security Policies (FSDPP_OSP), Version 1.7, 27
November 2009, BSI-CC-PP-0062-2010 [8]
● for the Functionality: PP conformant
Common Criteria Part 2 extended
● for the Assurance: Common Criteria Part 3 conformant
ADV_ARC.1, ADV_FSP.2, ADV_TDS.1, AGD_OPE.1,
AGD_PRE.1, ALC_CMC.2, ALC_CMS.2, ALC_DEL.1,
ALC_FLR.1, ASE_CCL.1, ASE_ECD.1, ASE_INT.1,
ASE_OBJ.2, ASE_REQ.2, ASE_SPD.1, ASE_TSS.1,
ATE_COV.1, ATE_FUN.1, ATE_IND.2
The results of the evaluation are only applicable to the TOE as defined in chapter 2 and
the configuration as outlined in chapter 8 above.
15 / 20
Certification Report BSI-DSZ-CC-1042-V2-2023
9.2. Results of cryptographic assessment
The TOE does not include cryptographic mechanisms. Thus, no such mechanisms were
part of the assessment.
10. Obligations and Notes for the Usage of the TOE
The documents as outlined in table 2 contain necessary information about the usage of the
TOE and all security hints therein have to be considered. In addition all aspects of
Assumptions, Threats and OSPs as outlined in the Security Target not covered by the TOE
itself need to be fulfilled by the operational environment of the TOE.
The customer or user of the product shall consider the results of the certification within his
system risk management process. In order for the evolution of attack methods and
techniques to be covered, he should define the period of time until a re-assessment of the
TOE is required and thus requested from the sponsor of the certificate.
If available, certified updates of the TOE should be used. If non-certified updates or
patches are available the user of the TOE should request the sponsor to provide a re-
certification. In the meantime a risk management process of the system using the TOE
should investigate and decide on the usage of not yet certified updates and patches or
take additional measures in order to maintain system security.
11. Security Target
For the purpose of publishing, the Security Target [6] of the Target of Evaluation (TOE) is
provided within a separate document as Annex A of this report.
12. Definitions
12.1. Acronyms
AIS Application Notes and Interpretations of the Scheme
API Application Programming Interface
BSI Bundesamt für Sicherheit in der Informationstechnik / Federal Office for
Information Security, Bonn, Germany
BSIG BSI-Gesetz / Act on the Federal Office for Information Security
CCRA Common Criteria Recognition Arrangement
CC Common Criteria for IT Security Evaluation
CEM Common Methodology for Information Technology Security Evaluation
cPP Collaborative Protection Profile
EAL Evaluation Assurance Level
ETR Evaluation Technical Report
IT Information Technology
ITSEF Information Technology Security Evaluation Facility
PAD Presentation Attack Detection
16 / 20
BSI-DSZ-CC-1042-V2-2023 Certification Report
PP Protection Profile
SAR Security Assurance Requirement
SDK Software Development Kit
SFP Security Function Policy
SFR Security Functional Requirement
ST Security Target
TOE Target of Evaluation
TSF TOE Security Functionality
12.2. Glossary
Augmentation - The addition of one or more requirement(s) to a package.
Collaborative Protection Profile - A Protection Profile collaboratively developed by an
International Technical Community endorsed by the Management Committee.
Extension - The addition to an ST or PP of functional requirements not contained in CC
part 2 and/or assurance requirements not contained in CC part 3.
Formal - Expressed in a restricted syntax language with defined semantics based on well-
established mathematical concepts.
Informal - Expressed in natural language.
Object - A passive entity in the TOE, that contains or receives information, and upon which
subjects perform operations.
Package - named set of either security functional or security assurance requirements
Protection Profile - A formal document defined in CC, expressing an implementation
independent set of security requirements for a category of IT Products that meet specific
consumer needs.
Security Target - An implementation-dependent statement of security needs for a specific
identified TOE.
Semiformal - Expressed in a restricted syntax language with defined semantics.
Subject - An active entity in the TOE that performs operations on objects.
Target of Evaluation - An IT Product and its associated administrator and user guidance
documentation that is the subject of an Evaluation.
TOE Security Functionality - Combined functionality of all hardware, software, and
firmware of a TOE that must be relied upon for the correct enforcement of the SFRs.
17 / 20
Certification Report BSI-DSZ-CC-1042-V2-2023
13. Bibliography
[1] Common Criteria for Information Technology Security Evaluation, Version 3.1,
Part 1: Introduction and general model, Revision 5, April 2017
Part 2: Security functional components, Revision 5, April 2017
Part 3: Security assurance components, Revision 5, April 2017
https://www.commoncriteriaportal.org
[2] Common Methodology for Information Technology Security Evaluation (CEM),
Evaluation Methodology, Version 3.1, Rev. 5, April 2017,
https://www.commoncriteriaportal.org
[3] BSI certification: Scheme documentation describing the certification process (CC-
Produkte) and Scheme documentation on requirements for the Evaluation Facility,
approval and licencing (CC-Stellen), https://www.bsi.bund.de/zertifizierung
[4] Application Notes and Interpretations of the Scheme (AIS) as relevant for the TOE7
https://www.bsi.bund.de/AIS
[5] German IT Security Certificates (BSI 7148), periodically updated list published also
on the BSI Website, https://www.bsi.bund.de/zertifizierungsreporte
[6] Security Target BSI-DSZ-CC-1042-V2-2023, Version 4.1, 13 October 2022,
DERMALOG Fingerprint PAD Kit LF10 – Security Target, DERMALOG Identification
Systems GmbH
[7] Evaluation Technical Report, Version 1, 14 October 2022, TÜV Informationstechnik
GmbH (confidential document)
[8] Fingerprint Spoof Detection Protection Profile based on Organisational Security
Policies (FSDPP_OSP), Version 1.7, 27 November 2009, BSI-CC-PP-0062-2010
[9] Fingerprint Spoof Detection Evaluation Guidance, Version 2.1, 18 December 2009
[10] Toolbox022017, February 2017, BSI (confidential document)
[11] Configuration list for the TOE: List of references DERMALOG Fingerprint PAD Kit
LF10, Version 2.7, 14 October 2022, DERMALOG Identification Systems GmbH
(confidential document)
[12] DERMALOG Guidance Addendum DERMALOG Fingerprint PAD Kit LF10,
Version 3.0, 13 October 2022, DERMALOG Identification Systems GmbH
[13] DERMALOG Fingerprint Scanner LF10 User Guide, Version 3.9, 27 June 2021,
DERMALOG Identification Systems GmbH
[14] DermalogBPLF10Plugin.chm (identified via hashsum, cmp. table 2) DERMALOG
Identification Systems GmbH
7
specifically
• AIS 32, Version 7, CC-Interpretationen im deutschen Zertifizierungsschema
18 / 20
BSI-DSZ-CC-1042-V2-2023 Certification Report
C. Excerpts from the Criteria
For the meaning of the assurance components and levels the following references to the
Common Criteria can be followed:
• On conformance claim definitions and descriptions refer to CC part 1 chapter 10.5
• On the concept of assurance classes, families and components refer to CC Part 3
chapter 7.1
• On the concept and definition of pre-defined assurance packages (EAL) refer to CC
Part 3 chapters 7.2 and 8
• On the assurance class ASE for Security Target evaluation refer to CC Part 3
chapter 12
• On the detailed definitions of the assurance components for the TOE evaluation
refer to CC Part 3 chapters 13 to 17
• The table in CC part 3 , Annex E summarizes the relationship between the
evaluation assurance levels (EAL) and the assurance classes, families and
components.
The CC are published at https://www.commoncriteriaportal.org/cc/
19 / 20
Certification Report BSI-DSZ-CC-1042-V2-2023
D. Annexes
List of annexes of this certification report
Annex A: Security Target provided within a separate document.
Note: End of report
20 / 20