ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target
:FQR No: 110 7792
FQR Issue: 3
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
Legal Notice
© OT. All rights reserved.
Specifications and information are subject to change without notice.
The products described in this document are subject to continuous development and improvement.
All trademarks and service marks referred to herein, whether registered or not in specific countries, are the properties
of their respective owners.
** Printed versions of this document are uncontrolled **
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
Table of contents
1 SECURITY TARGET INTRODUCTION 10
1.1 Purpose ..............................................................................................................10
1.2 Objective of the security target............................................................................10
1.3 Security Target identification...............................................................................11
1.4 TOE technical identification.................................................................................11
1.5 IC identification...................................................................................................12
2 TOE OVERVIEW 13
2.1 Product overview................................................................................................13
2.2 TOE usages and major security features...............................................................14
2.3 TOE type .............................................................................................................15
2.4 Required non-TOE hardware/software/firmware.................................................15
3 TOE DESCRIPTION 16
3.1 TOE scope ...........................................................................................................16
3.2 Block description.................................................................................................16
3.2.1 Integrated Circuit – NXP P60.................................................................................... 17
3.2.2 Low layer.................................................................................................................. 17
3.2.2.1 Basic Input and Output System (BIOS) ............................................................................ 17
3.2.2.2 Cryptography (Crypto)..................................................................................................... 17
3.2.3 Tools modules.......................................................................................................... 17
3.2.3.1 File System Management (FSM)...................................................................................... 17
3.2.3.2 Secure Messaging (SM) ................................................................................................... 17
3.2.3.3 Pin Password Management (PPM).................................................................................. 17
3.2.3.4 Cryptography Key Management (CKM)........................................................................... 17
3.2.3.5 Authentication and Key Management (AKM) ................................................................. 17
3.2.3.6 Toolbox............................................................................................................................ 18
3.2.4 Applicative modules................................................................................................. 18
3.2.4.1 Terminal Authentication (TA).......................................................................................... 18
3.2.4.2 Chip Authentication (CA)................................................................................................. 18
3.2.4.3 Supplemental Access Control (SAC) ................................................................................ 18
3.2.4.4 Digitally Blurred Image (DBI)........................................................................................... 18
3.2.4.5 Access Conditions Engine (ACE) ...................................................................................... 18
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
3.2.5 Operating System..................................................................................................... 18
3.2.5.1 Application Creation Engine............................................................................................ 18
3.2.6 Application layer ...................................................................................................... 19
3.2.6.1 Resident Application ....................................................................................................... 19
3.2.6.2 eDoc Application ............................................................................................................. 19
3.2.6.3 eSign Application............................................................................................................. 19
3.2.6.4 Authentication Procedure............................................................................................... 19
4 TOE LIFE CYCLE 20
4.1 Life cycle overview ..............................................................................................20
4.2 Phase 1 “Development” (Step1 and 2) .................................................................22
4.3 Phase 2 “Manufacturing” (Steps 3 to 5)................................................................22
4.4 Phase 3 “Personalization of the TOE”...................................................................24
4.5 Phase 4 “Operational Use” ..................................................................................24
5 CONFORMANCE CLAIMS 25
5.1 Common Criteria conformance ............................................................................25
5.2 Protection Profile conformance ...........................................................................25
5.2.1 Correspondences and additions of SFR ................................................................... 28
6 SECURITY PROBLEM DEFINITION 30
6.1 Assets, objects, users and subjects.......................................................................30
6.1.1 Assets and objects.................................................................................................... 30
6.1.1.1 From PP SSCD-2............................................................................................................... 30
6.1.1.2 Others.............................................................................................................................. 30
6.1.2 Users and subjects acting for users.......................................................................... 31
6.1.2.1 From PP SSCD - 2............................................................................................................. 31
6.1.2.2 Others.............................................................................................................................. 31
6.2 Threats ...............................................................................................................31
6.2.1 Threat agents ........................................................................................................... 31
6.2.1.1 From PP SSCD - 2............................................................................................................. 31
6.2.1.2 Others.............................................................................................................................. 31
6.2.2 Threats from PP SSCD - 2 ......................................................................................... 32
6.2.2.1 T.SCD_Divulg Storing, copying and releasing of the signature creation data............... 32
6.2.2.2 T.SCD_Derive Derive the signature creation data ........................................................ 32
6.2.2.3 T.Hack_Phys Physical attacks through the TOE interfaces .......................................... 32
6.2.2.4 T.SVD_Forgery Forgery of the signature verification data ........................................... 32
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
6.2.2.5 T.SigF_Misuse Misuse of the signature creation function of the TOE.......................... 32
6.2.2.6 T.DTBS_Forgery Forgery of the DTBS/R........................................................................ 32
6.2.2.7 T.Sig_Forgery Forgery of the electronic signature....................................................... 32
6.2.3 Threats for Loading of Additional Code ................................................................... 32
6.2.3.1 T.Unauthorized_Load...................................................................................................... 32
6.2.3.2 T.Bad_Activation ............................................................................................................. 33
6.2.3.3 T.TOE_Identification_Forgery ......................................................................................... 33
6.2.4 Threats for pre-personalization and personalization .............................................. 33
6.2.4.1 T.Pre_Perso ..................................................................................................................... 33
6.2.4.2 T.Perso............................................................................................................................. 33
6.3 Organizational security policies ...........................................................................34
6.3.1 Organizational Security Policies from the PP SSCD – 2............................................ 34
6.3.1.1 P.CSP_QCert Qualified certificate................................................................................ 34
6.3.1.2 P.QSign Qualified electronic signatures....................................................................... 34
6.3.1.3 P.Sigy_SSCD TOE as secure signature creation device................................................. 34
6.3.1.4 P.Sig_Non-Repud Non-repudiation of signatures......................................................... 34
6.4 Assumptions .......................................................................................................35
6.4.1 Assumptions from the PP SSCD – 2.......................................................................... 35
6.4.1.1 A.CGA Trustworthy certificate generation application................................................ 35
6.4.1.2 A.SCA Trustworthy signature creation application...................................................... 35
7 SECURITY OBJECTIVES 36
7.1 Security Objectives for the TOE............................................................................36
7.1.1 Security Objectives from PP SSCD - 2....................................................................... 36
7.1.1.1 Relation to PP SSCD KI..................................................................................................... 36
7.1.1.2 OT.Lifecycle_Security Lifecycle security ....................................................................... 36
7.1.1.3 OT.SCD/SVD_Auth_Gen Authorized SCD/SVD generation............................................ 36
7.1.1.4 OT.SCD_Unique Uniqueness of the signature creation data........................................ 36
7.1.1.5 OT.SCD_SVD_Corresp Correspondence between SVD and SCD.................................... 37
7.1.1.6 OT.SCD_Secrecy Secrecy of the signature creation data.............................................. 37
7.1.1.7 OT.Sig_Secure Cryptographic security of the electronic signature .............................. 37
7.1.1.8 OT.Sigy_SigF Signature creation function for the legitimate signatory only ............... 37
7.1.1.9 OT.DTBS_Integrity_TOE DTBS/R integrity inside the TOE ............................................. 37
7.1.1.10 OT.EMSEC_Design Provide physical emanations security............................................ 37
7.1.1.11 OT.Tamper_ID Tamper detection................................................................................. 37
7.1.1.12 OT.Tamper_Resistance Tamper resistance ................................................................... 38
7.1.2 Security Objectives for the Loading of Additional Code .......................................... 38
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
7.1.2.1 OT.Secure_Load_ACode.................................................................................................. 38
7.1.2.2 OT.Secure_AC_Activation ............................................................................................... 38
7.1.2.3 OT.TOE_Identification ..................................................................................................... 38
7.1.3 Security Objectives for pre-personalization and personalization............................ 38
7.1.3.1 OT.Pre_Perso................................................................................................................... 38
7.1.3.2 OT.Perso.......................................................................................................................... 39
7.2 Security objectives for the operational environment............................................39
7.2.1 Security objectives from PP SSCD-2......................................................................... 39
7.2.1.1 Relation to PP SSCD-3 KI (key import)............................................................................. 39
7.2.1.2 OE.SVD_Auth Authenticity of the SVD......................................................................... 39
7.2.1.3 OE.CGA_QCert Generation of qualified certificates..................................................... 39
7.2.1.4 OE.SSCD_Prov_Service Authentic SSCD provided by SSCD-provisioning service .......... 39
7.2.1.5 OE.HID_VAD Protection of the VAD ............................................................................ 39
7.2.1.6 OE.DTBS_Intend SCA sends data intended to be signed .............................................. 40
7.2.1.7 OE.DTBS_Protect SCA protects the data intended to be signed .................................. 40
7.2.1.8 OE.Signatory Security obligation of the signatory....................................................... 40
8 EXTENDED COMPONENTS DEFINITION 41
8.1 Definition of the Family FPT_EMS ........................................................................41
8.2 Definition of the Family FAU_SAS ........................................................................42
9 SECURITY REQUIREMENTS 44
9.1 Security functional requirements from PP SSCD – 2..............................................44
9.1.1 Cryptographic support (FCS).................................................................................... 44
9.1.1.1 FCS_CKM.1/RSA Cryptographic key generation ............................................................. 44
9.1.1.2 FCS_CKM.1/ECDSA Cryptographic key generation......................................................... 44
9.1.1.3 FCS_CKM.4 Cryptographic key destruction................................................................... 45
9.1.1.4 FCS_COP.1 Cryptographic operation............................................................................ 45
9.1.2 User data protection (FDP) ...................................................................................... 46
9.1.2.1 FDP_ACC.1/SCD/SVD_Generation Subset access control .............................................. 46
9.1.2.2 FDP_ACF.1/SCD/SVD_Generation Security attribute based access control.................... 47
9.1.2.3 FDP_ACC.1/SVD_Transfer Subset access control .......................................................... 47
9.1.2.4 FDP_ACF.1/SVD_Transfer Security attribute based access control............................... 48
9.1.2.5 FDP_ACC.1/Signature_Creation Subset access control.................................................. 48
9.1.2.6 FDP_ACF.1/Signature creation Security attribute based access control....................... 49
9.1.2.7 FDP_RIP.1 Subset residual information protection ..................................................... 50
9.1.2.8 FDP_SDI.2/Persistent Stored data integrity monitoring and action............................. 50
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
9.1.2.9 FDP_SDI.2/DTBS Stored data integrity monitoring and action..................................... 50
9.1.3 Identification and authentication (FIA).................................................................... 51
9.1.3.1 FIA_UID.1 Timing of identification............................................................................... 51
9.1.3.2 FIA_UAU.1 Timing of authentication........................................................................... 51
9.1.3.3 FIA_AFL.1 Authentication failure handling .................................................................. 52
9.1.4 Security Management (FMT) ................................................................................... 52
9.1.4.1 FMT_SMR.1 Security roles........................................................................................... 52
9.1.4.2 FMT_SMF.1 Security management functions.............................................................. 53
9.1.4.3 FMT_MOF.1 Management of security functions behavior.......................................... 53
9.1.4.4 FMT_MSA.1/Admin Management of security attributes ............................................. 53
9.1.4.5 FMT_MSA.1/Signatory Management of security attributes ........................................ 54
9.1.4.6 FMT_MSA.2 Secure security attributes ....................................................................... 54
9.1.4.7 FMT_MSA.3 Static attribute initialisation.................................................................... 54
9.1.4.8 FMT_MSA.4 Security attribute value inheritance....................................................... 55
9.1.4.9 FMT_MTD.1/Admin Management of TSF data............................................................. 55
9.1.4.10 FMT_MTD.1/Signatory Management of TSF data........................................................ 56
9.1.5 Protection of the TSF (FPT) ...................................................................................... 56
9.1.5.1 FPT_EMS.1 TOE Emanation ......................................................................................... 56
9.1.5.2 FPT_FLS.1 Failure with preservation of secure state.................................................... 56
9.1.5.3 FPT_PHP.1 Passive detection of physical attack........................................................... 57
9.1.5.4 FPT_PHP.3 Resistance to physical attack..................................................................... 57
9.1.5.5 FPT_TST.1 TSF testing .................................................................................................. 58
9.2 Security Functional Requirements for Manufacturing, Personalization and Loading of
Additional Code ..................................................................................................58
9.2.1 SFRs for additional code........................................................................................... 58
9.2.1.1 FAU_STG.2/MP_Add_code Guarantees of audit data availability ................................. 58
9.2.1.2 FCS_CKM.1/MP_Add_code Cryptographic key generation............................................ 59
9.2.1.3 FCS_COP.1/MP_ENC_Add_code Cryptographic operation............................................. 59
9.2.1.4 FCS_COP.1/MP_MAC_Add_code Cryptographic operation............................................ 59
9.2.1.5 FDP_UIT.1/MP_Add_code Data exchange integrity...................................................... 60
9.2.1.6 FMT_MTD.1/MP_Add_code Management of TSF data ................................................ 60
9.2.1.7 FMT_MTD.1/MP_KEY_READ_Add_code Management of TSF data ............................... 60
9.2.1.8 FMT_SMR.1/MP_Add_Code Security roles................................................................... 61
9.2.1.9 FPT_EMS.1/MP_Add_code TOE Emanation.................................................................. 61
9.2.1.10 FTP_ITC.1/MP_Add_code Inter-TSF trusted channel.................................................... 61
9.2.2 Manufacturing and Personalization......................................................................... 61
9.2.2.1 FCS_CKM.1/MP Cryptographic key generation............................................................. 61
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
9.2.2.2 FCS_COP.1/MP_ENC_3DES Cryptographic operation.................................................... 62
9.2.2.3 FCS_COP.1/MP_ENC_AES Cryptographic operation ...................................................... 62
9.2.2.4 FCS_COP.1/MP_MAC_3DES Cryptographic operation................................................... 62
9.2.2.5 FCS_COP.1/MP_MAC_AES Cryptographic operation..................................................... 63
9.2.2.6 FCS_COP.1/MP_AUTH_3DES Cryptographic operation ................................................. 63
9.2.2.7 FCS_COP.1/MP_AUTH_AES Cryptographic operation.................................................... 63
9.2.2.8 FCS_COP.1/MP_SHA Cryptographic operation ............................................................. 63
9.2.2.9 FDP_ACC.2/MP Complete access control...................................................................... 64
9.2.2.10 FDP_ACF.1/MP Security attribute based access control ............................................... 64
9.2.2.11 FDP_ITC.1/MP Import of user data without security attributes ................................... 65
9.2.2.12 FDP_UCT.1/MP Basic data exchange confidentiality .................................................... 65
9.2.2.13 FDP_UIT.1/MP Data exchange integrity........................................................................ 65
9.2.2.14 FIA_AFL.1/MP Authentication failure handling............................................................ 66
9.2.2.15 FIA_UAU.1/MP Timing of authentication...................................................................... 66
9.2.2.16 FIA_UID.1/MP Timing of identification......................................................................... 66
9.2.2.17 FIA_UAU.4/MP_3DES Single-use authentication mechanisms ..................................... 66
9.2.2.18 FIA_UAU.4/MP_AES Single-use authentication mechanisms ....................................... 66
9.2.2.19 FIA_UAU.5/MP_3DES Multiple authentication mechanisms ........................................ 67
9.2.2.20 FIA_UAU.5/MP_AES Multiple authentication mechanisms .......................................... 67
9.2.2.21 FMT_MTD.1/MP Management of TSF data................................................................... 67
9.2.2.22 FTP_ITC.1/MP Inter-TSF trusted channel ..................................................................... 67
9.2.2.23 FMT_MTD.1/MP_INI_ENA Management of TSF data .................................................... 68
9.2.2.24 FMT_MTD.1/MP_INI_DIS Management of TSF data...................................................... 68
9.2.2.25 FMT_MTD.1/MP_KEY_READ Management of TSF data................................................. 68
9.2.2.26 FMT_MTD.1/MP_KEY_WRITE Management of TSF data ............................................... 68
9.2.2.27 FAU_SAS.1/MP Audit storage........................................................................................ 68
9.2.2.28 FMT_SMF.1/MP Specification of Management Functions............................................ 68
9.2.2.29 FMT_SMR.1/MP Security Roles..................................................................................... 69
9.2.2.30 FPT_EMS.1/MP TOE Emanation .................................................................................... 69
10 TOE SUMMARY SPECIFICATION 70
10.1 TOE Summary Specification .................................................................................70
11 RATIONALES 73
11.1 Security objectives and Security Problem Definition.............................................73
11.2 Security objectives rationale................................................................................73
11.2.1 Security objectives backtracking.............................................................................. 73
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
11.2.2 Security objectives sufficiency................................................................................. 74
11.3 Security requirements and security objectives .....................................................74
11.3.1 Rationale tables of Security Objectives and SFRs.................................................... 74
11.3.2 Rationale of Security Objectives and SFRs............................................................... 78
12 REFERENCES 79
Specifications ....................................................................................................................79
Oberthur Specifications .....................................................................................................79
Protection Profiles.............................................................................................................79
Chips References ...............................................................................................................80
Standards..........................................................................................................................80
CC 80
13 ACRONYMS 82
14 LIST OF TABLES AND FIGURES 83
Figures 83
Tables 83
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
1 SECURITY TARGET INTRODUCTION
1.1 Purpose
The objective of this document is to present the Public Security Target SSCD-2 of the ID-One ePass V3 Full
EAC v2 product on NXP components from P60 family.
1.2 Objective of the security target
This security target describes the security needs for ID-One ePass V3 Full EAC v2 product. The product is
conforming to PP SSCD-2 and adds requirements for prepersonalization and personalization.
This security target aims to satisfy the requirements of Common Criteria level EAL5 augmented as defined
in §1.3 in defining the security enforcing functions of the Target Of Evaluation and describing the
environment in which it operates.
The objectives of this Security Target are:
- To describe the Target of Evaluation (TOE), its life cycle and to position it in the smart card life
cycle.
- To describe the security environment of the TOE including the assets to be protected and the
threats to be countered by the TOE and by the operational environment during the platform
active phases.
- To describe the security objectives of the TOE and its supporting environment in terms of
integrity and confidentiality of sensitive information. It includes protection of the TOE (and its
documentation) during the product active phases.
- To specify the security requirements which include the TOE functional requirements, the TOE
assurance requirements and the security requirements for the environment.
- To describe the summary of the TOE specification including a description of the security
functions and assurance measures that meet the TOE security requirements.
- To present evidence that this ST is a complete and cohesive set of requirements that the TOE
provides on an effective set of IT security countermeasures within the security environment,
and that the TOE summary specification addresses the requirements.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
1.3 Security Target identification
Title ID-One eIDAS v1.0 in SSCD-2 configuration Security Target
Editor Oberthur Technologies
CC version 3.1 revision 4
EAL EAL5 augmented with AVA_VAN.5 and ALC_DVS.2
PP Protection profile for secure signature creation device — Part 2: Device with
key generation, version 2.0.1, 2012-01-23 BSI-CC-PP-0059-2009-MA-01
ST Reference FQR 110 7676 Issue 6
ITSEF LETI
Certification Body ANSSI
Evaluation Scheme FR
Table 1-1 - General Identification
1.4 TOE technical identification
Product name ID-One ePass V3 Full EAC v2
Commercial
name of TOE 1
ID-One eIDAS v1.0 in SSCD-2 configuration on NXP P60x080 PVC/PVG
IC type ‘6C14’ (P60D080 VC)
‘6014’ (P60D080 VG)
‘6019’ (P60C080 VG)
Additional code 1
Mandatory
generic
Identification
‘082456FF412E4D1EC087005B56A9A2CAC0B6558F4CAAE041D8B5A69345559B562A6F
4C8E’
Additional code 2
Optional DBI
Identification
‘082844FFE339C30BC6A81162413612FE2698284FA6CD28AA5CF5257A20B83611E58E9
BEE’
Table 1-2 - TOE technical identification
Nota bene
- The additional code is encrypted with the LSK key
- An optional additional code (functional) can be loaded. This additional code, relative to the Digitally
Blurred Image process (DBI), is part of the product, but not in the scope of the evaluation.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
1.5 IC identification
IC Reference NXP P60 IC
TOE 1 NXP P60x080/052/040 PVC/PVG [R35]
EAL6 + ALC_FLR.1 + ASE_TSS.2
Communication protocol Contact and contactless and dual
Memory ROM
Chip Manufacturer NXP Semiconductors
Table 1-3 - Chip Identification
The use of the word ‘PIN’ throughout this document can always refer to a numerical as well as to a
biometric PIN.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
2 TOE OVERVIEW
2.1 Product overview
The product ID-One ePass V3 Full EAC v2 is a multi-applicative native software, embedded in contact
and/or contactless smart card integrated circuits of different form factors. During the pre-personalization
and personalization phases, the product can be configured to serve different use cases.
The product supports the storage and retrieval of structured information compliant to the Logical Data
Structure as specified in [R2]. It also provides standard authentication protocols, namely Basic Access
Control [R27], Supplementary Access Control [R33], Extended Access Control ([R28] and [R29]), the Basic
Access Protection [R9] and Extended Access Protection [R9]. Additionally, it supplies PIN management [R36]
and signature services [R37].
The product is intended to host 4 types of applications: MRTD-IDL, eID, eSign and Dauth. Moreover, further
configuration may also be done to each type of application to serve use cases other than those behaviorally
defined in the referenced normative documents.
This product is embedded on the IC described in § 1.5.
The product is closed. The set of available applications is fully configured at the end of the personalization
phase.
The ID-One ePass V3 Full EAC v2 architecture can be viewed as shown in the following picture:
Figure 1 - Product architecture
Figure 1 – Product architecture
NXP P60
Platform
layer
Low layer
Services
Authentication Protocols
Specific Features
Application
layer
Block 1:
MRTD - IDL
Block 2:
eID
Block 3:
eSign
Block 4:
Dauth
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
The TOE is a subset of the product dedicated to the Signature Application. The eSign application contains
the following 5 configurations:
eSign Configurations PP Targeted EAL
eSign SSCD-2
SSCD 2 CEN/EN 419 211-2
(ex CEN/EN 14169-2) (BSI-CC-PP-0059-2009-MA-
01)
EAL5 + DVS.2 + VAN.5
eSign SSCD-3 SSCD 3 CEN/EN 419 211-3
(ex CEN/EN 14169-3) (BSI-CC-PP-0075-2012)
EAL5 + DVS.2 + VAN.5
eSign SSCD-4 SSCD 4 CEN/EN 419 211-4
(ex CEN/EN 14169-4) (BSI-CC-PP-0071-2012)
EAL5 + DVS.2 + VAN.5
eSign SSCD-5 SSCD 5 CEN/EN 419 211-5
(ex CEN/EN 14169-5) (BSI-CC-PP-0072-2012)
EAL5 + DVS.2 + VAN.5
eSign SSCD-6 SSCD 6 CEN/EN 419 211-6
(ex CEN/EN 14169-6)(BSI-CC-PP-0076-2013)
EAL5 + DVS.2 + VAN.5
Table 2-1 - eSign Configurations
The scope of this TOE encompasses configuration SSCD-2 and the features it relies on.
The eSign application is configured during the pre-personalization phase, using the Application Creation
Engine. The other secure applications present in the product (MRTD-DL, eID and Dauth) are not in this TOE.
They are evaluated separately.
2.2 TOE usages and major security features
The eSign application provides different services that make each card a secure signature creation device as
defined in [R23].
The TOE major security features in the operational phase are the functions:
(1) to generate signature creation data (SCD) and the correspondent signature-verification data (SVD),
(2) to export the SVD for certification,
(3) to, optionally, receive and store certificate info (only if personalizer creates it),
(4) to switch the TOE from a non-operational state to an operational state, and
(5) if in an operational state, to create digital signatures for data with the following steps (conformant
to [R3], [R4], and [R22]; described in Section §5.3) :
(a) authenticate the signatory (using the RAD verification) and determine its intent to sign,
(b) receive data to be signed or a unique representation thereof (DTBS/R),
(c) apply an appropriate cryptographic signature creation function using the selected SCD to
the DTBS/R.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
It also allows the authentication of one (or several) administrator(s) of the TOE who may have special
rights to administrate the SCD and SVD (generation), using either symmetric or asymmetric
mechanisms or PIN verification.
2.3 TOE type
The TOE (Target of evaluation) is a smartcard based on NXP chip. It is a combination of hardware and
software configured to securely create, use and manage signature creation data (SCD). The SSCD protects
the SCD during its whole life cycle as to be used in a signature creation process solely by its signatory.
The TOE comprises:
- Circuitry of the chip (the integrated circuit, IC)
- IC Dedicated Software with the parts IC Dedicated Test Software and IC Dedicated
Support Software
- IC Embedded Software (operating system)
- eSign application
- Associated guidance documentation
2.4 Required non-TOE hardware/software/firmware
N/A
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
3 TOE DESCRIPTION
3.1 TOE scope
The following diagram describes the architecture of the product and highlights (in orange) the components
of the product that are part of the TOE.
Figure 2 - Product architecture with TOE components
3.2 Block description
This section provides a quick overview of the functionalities of the components of the product. Note that
the Resident Application, the eDoc block, the whole Platform Layer and the IC provide functionalities to all
the applicative blocks 1 to 4.
Platform layer
Authentication Protocols Specific Features
Services
Low layer
Application layer
Block 3: eSign
Block
1
Block
2
Block
4
eSign
SSCD-2
eSign
Application
Resident
Application
eDoc
Application
Start-Up and Applications Manager
Application
Creation Engine
Integrated Circuit
NXP P60
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
3.2.1 Integrated Circuit – NXP P60
The TOE is embedded on NXP chip, as presented in Table 1-3 - Chip Identification. More information on the
chips is given in the related certification report [R35] and related Security Target.
3.2.2 Low layer
3.2.2.1 Basic Input and Output System (BIOS)
The BIOS module provides access management (read/write) functionalities to upper-layer application. It
also provides exception and communication functionalities.
3.2.2.2 Cryptography (Crypto)
The Cryptography module provides secure cryptographic functionalities to upper-layer applications.
3.2.3 Tools modules
3.2.3.1 File System Management (FSM)
The FSM module manages files and data objects according to ISO 7816-4 and 7816-9.
3.2.3.2 Secure Messaging (SM)
The SM module provides functionalities to encrypt/decrypt data for secure communication in pre-
personalization, personalization and operational use phase.
3.2.3.3 Pin Password Management (PPM)
The PPM module provides functionalities for numeric passwords and biometric templates management.
The passwords that can be used in connection with the eSign application are a global PIN, PUK, CAN (card
access number written on the card where the eSign application is installed on) and the eSign PIN, called
“RAD” in this Security Target. The use of the words ‘PIN’ throughout this document refers to a classical PIN
as well as to a biometric password.
The RAD management is in the scope of this evaluation. The management of the other PINs and passwords
not directly related to the signature application is evaluated separately.
3.2.3.4 Cryptography Key Management (CKM)
The CKM module is responsible for asymmetric cryptography key management and asymmetric
cryptography operations.
3.2.3.5 Authentication and Key Management (AKM)
This module supplies:
- Symmetric Key management
- Access Control for ‘Change MSK’ and ‘PUT KEY’ APDU
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
- Authentication and secure messaging to be used by the application integrating this module in
Prepersonalization and Personalization phases, based on Global Platform standard
3.2.3.6 Toolbox
The Toolbox module provides different kind of services to other modules.
3.2.4 Applicative modules
3.2.4.1 Terminal Authentication (TA)
The TA module processes the Terminal Authentication (v1 and v2) mechanism. Terminal Authentication v2
is part of the EACv2 procedure.
3.2.4.2 Chip Authentication (CA)
The CA module processes the Chip Authentication (v1 and v2) mechanism. Chip Authentication v2 is part of
the EACv2 procedure.
3.2.4.3 Supplemental Access Control (SAC)
The SAC module provides functionalities to process the PACE v2 mechanism.
3.2.4.4 Digitally Blurred Image (DBI)
The Digital Blurred Image module allows the blurring of a JPG file stored in a transparent file during the
personalization phase. This functionality is optionally loaded with additional code.
3.2.4.5 Access Conditions Engine (ACE)
The ACE module is in charge of the verification of the Access Conditions of an object (file, key and PIN)
when an application tries to access this object.
3.2.5 Operating System
3.2.5.1 Application Creation Engine
The Application Creation Engine is a complete set of commands used to personalize the card and its
application(s). It includes:
 Administrative services for card configuration and life cycle management, key storage, pin storage
and data storage.
 Storage of the Active Authentication Key (ECC and RSA Keys)
 Storage of multiple Chip Authentication Keys under the ADF (supporting ECC and RSA Keys)
 Storage of Trusted DL Root Keys under the ADF.
 Storage of CVCA Keys under the Master File.
 Storage of CVCA Keys under each ADF.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
3.2.6 Application layer
3.2.6.1 Resident Application
The Resident Application is a complete set of commands, which allows the management of the card in the
pre-personalization phase.
It supports the execution of an Authentication Procedure. Possible implementations include PACE or PACE
with EACv2 (which encompasses Terminal Authentication v2 and Chip Authentication v2).
3.2.6.2 eDoc Application
The eDoc Application is a command dispatcher that is used only when the product is also hosting other
applications than eSign. If only the eSign application is present on the card, this application is inactive: the
eSign application directly receives all the commands if it has been selected before.
3.2.6.3 eSign Application
The eSign application is a complete set of commands used for eSign application. This includes the
management of the RAD and the signature keys, and the signing operation.
3.2.6.4 Authentication Procedure
In the rest of the document, especially in the section SFRs, Authentication Procedure means PACE, EAC,
Terminal Authentication, Chip Authentication, Verify PIN or a combination of these.
Note that PACE, EAC, Terminal Authentication and Chip Authentication have already been certified in
previous projects. Verify PIN is part of this evaluation (RAD Management).
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
4 TOE LIFE CYCLE
4.1 Life cycle overview
Figure 3 - TOE Lifecycle
TOE delivery point
ALC
phase
Step 1
Step 2
Step3
Software development
Patch development
IC photomask
fabrication
IC database
construction
IC manufacturing IC testing
Step 7
Smartcard
product
End usage
Application
End usage
Smartcard
End of life
Application
End of life
AGD OPE
AGD
phase
Step 4
Testing
Step 5 Testing
Step 6
AGD PRE
Card printing
Micromodule
Embedding
Personalization
Pre-Personalization
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
The table below presents the roles involved in the development, manufacturing and personalization of the
TOE:
Roles Subject
IC developer NXP Semiconductors
IC Manufacturer NXP Semiconductors
TOE developer Oberthur Technologies
Manufacturer NXP Semiconductors
Oberthur Technologies or another agent
Pre-personalizer Oberthur Technologies or another agent
Personalization agent Oberthur Technologies or another agent
Table 4-1 - Roles identification on the life cycle
The table below presents the subjects following TOE life cycle steps in accordance with the standard smart
card life cycle [R26] and the Protection Profile life cycle. The table is divided into the phases, the TOE
delivery point and the coverage:
Steps Phase Subject Covered by
Sites
Step 1 Development Oberthur Technologies ALC R&D Sites Pessac and
Colombes
Step 2 Development NXP Semiconductors IC certification See IC
certification
document
Step 3 Manufacturing NXP Semiconductors IC certification See IC
certification
document
TOE delivery point
Step 4 Manufacturing eSign Manufacturer (Pre-
personalizer)
AGD_PRE
Step 5 Manufacturing eSign Manufacturer (Pre-
personalizer)
AGD_PRE
Step 6 Personalization Personalization agent AGD_PRE
Step 7 Operational Use End user AGD_OPE
Table 4-2 - Subjects identification following life cycle steps
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
4.2 Phase 1 “Development” (Step1 and 2)
(Step1) The TOE is developed in phase 1. The IC developer develops the integrated circuit, the IC Dedicated
Software and the guidance documentation associated with these TOE components.
(Step2) The TOE developer uses the guidance documentation for the integrated circuit and the guidance
documentation for relevant parts of the IC Dedicated Software and develops the IC Embedded Software
(operating system), the eSign application and the guidance documentation associated with these TOE
components.
The manufacturing documentation of the IC including the IC Dedicated Software and the Embedded
Software in the non-volatile non-programmable memories is securely delivered to the IC manufacturer. The
IC Embedded Software in the non-volatile programmable memories, the eSign application and the guidance
documentation is securely delivered to the Manufacturer.
4.3 Phase 2 “Manufacturing” (Steps 3 to 5)
(Step3) In a first step, the TOE integrated circuit is produced containing the secure signature creation
device’s chip Dedicated Software and the parts of the secure signature creation device’s chip Embedded
Software in the non- volatile non-programmable memories (ROM). The IC manufacturer writes the IC
Identification Data onto the chip to control the IC as secure signature creation device material during the IC
manufacturing and the delivery process to the Manufacturer. The IC is securely delivered from the IC
manufacture to the Manufacturer. If necessary, the IC manufacturer adds the parts of the IC Embedded
Software in the non-volatile programmable memories (for instance EEPROM). The IC manufacturer adds
initialization data in EEPROM and keys (MSK, LSK).
TOE delivery point
(Step4) The Manufacturer combines the IC with hardware for the contact based / contactless interface in
the secure signature creation device unless the secure signature creation device consists of the card only.
(Step5) Pre-personalization phase
The Manufacturer
(i) adds the IC Embedded Software or part of it and the additional source code in the non-
volatile programmable memories if necessary,
(ii) creates the eSign application, and
(iii) equips the secure signature creation device’s chips with pre-personalization Data.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
The pre-personalized secure signature creation device together with the IC Identifier is securely delivered
from the Manufacturer to the Personalization Agent. The Manufacturer also provides the relevant parts of
the guidance documentation to the Personalization Agent.
Additional code loading is performed in Pre-personalization phase encrypted with the LSK. It is compliant to
ANSSI Note 6 [R61].
The additional code loading process is performed by the Pre-personalizer in the following steps, via the
Command LOAD SECURE:
- Additional code generation
- MSK authentication
- LSK derivation
- Memory area definition
- Loading of the additional code
- Secure activation of the additional code
The additional code loading is performed before the creation of the MF file during Pre-personalization.
Identification of the additional code loading is given in Table 1-2 - TOE technical identification.
The additional code is generated by Oberthur Technologies: developed, compiled, ciphered and signed.
After generation, it is sent to the eSign manufacturer to load to in the (initial) TOE.
Loading of the additional code
The additional code is loaded to the (initial) TOE by the Pre-personalizer, who shall authenticate itself to the
TOE beforehand. Upon reception, the (initial) TOE checks it has been generated by Oberthur Technologies
(by verifying the signature) before activating it.
Identification of the TOE
After successful loading and activation of the additional code, the TOE updates its identification data to
reflect the presence of the additional code.
Once the additional code(s) is (are) loaded, the following operations should be processed:
 Master File Creation
 Card’s Personalization Key Storage under Master File using PUT KEY command (see ISK [R41])
 CPLC Data Storage
 Application Creation (Create eSign ADF)
 eSign’s Personalization Key Storage under eSign ADF
 Set the current life phase to Personalization Phase
Keys are loaded encrypted with DEC key and potentially additionally with Secure Messaging.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
4.4 Phase 3 “Personalization of the TOE”
(Step 6) Personalization of the Secure Signature Device Creation
The personalization of the SSCD includes:
 Empty PIN container
 Empty key container
 Empty file with EF Identifier 0x0119
Some production steps, e.g. Step 5 (ii) and (iii) in Phase 2, may also take place in the Phase 3.
Keys are loaded encrypted with DEC key and potentially additionally with Secure Messaging.
4.5 Phase 4 “Operational Use”
(Step 7) The TOE is used as a signing document by a user to sign transactions in the « Operational
Use » phase.
Note that the personalization process and its environment may depend on specific security needs of an
issuing State or Organization. All production, generation and installation procedures after TOE delivery up
to the “Operational Use” (phase 4) have to be considered in the product evaluation process under AGD
assurance class.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
5 CONFORMANCE CLAIMS
5.1 Common Criteria conformance
This Security Target (ST) claims conformance to the Common Criteria version 3.1 revision 4 [R58], [R59] and
[R60].
The conformance to the CC is claimed as follows:
CC Conformance Claim
Part 1 Strict conformance
Part 2 Conformance with extensions:
- FPT_EMS.1 “TOE Emanation” (defined in [R26])
- FAU_SAS.1 “Audit data storage” (defined in [R26])
Part 3 Conformance with package EAL5 augmented with
- AVA_VAN.5 “Advanced methodical vulnerability analysis”
- ALC_DVS.2 “Sufficiency of security measures”
Table 5-1 - Conformance Claim
5.2 Protection Profile conformance
The Security Target claims strict conformance to the following Protection Profile written in CC version 3.1
revision 3: Protection profiles for secure signature creation device – Part 2: Device with key generation.
Version 2.0.1, 2012-01-23.
The following tables present the correspondence between the information from the SSCD-2 PP and the
information in this security target and when relevant the additions (in red) and the iterations (in blue) of
the SFRs of the Protection Profile.
From PP SSCD – 2 In this ST
Assets and objects
SCD SCD
SVD SVD
DTBS and DTBS/R DTBS and DTBS/R
RAD
TOE-ID
CPLC Data
Users and subjects acting for users
S.User S.User
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
S.Admin S.Admin
Signatory (S.Sigy) Signatory (S.Sigy)
Administrator (R.Admin) Administrator (R.Admin)
CSP (Certificate Service Provider); Refinement of
Administrator
Manufacturer
Pre-personalizer (Refinement of Administrator)
Personalizer (Refinement of Administrator)
Threat agents
Attacker Attacker
Threats
T.SCD_Divulg T.SCD_Divulg
T.SCD_Derive T.SCD_Derive
T.Hack_Phys T.Hack_Phys
T.SVD_Forgery T.SVD_Forgery
T.SigF_Misuse T.SigF_Misuse
T.DTBS_Forgery T.DTBS_Forgery
T.Sig_Forgery T.Sig_Forgery
T.Unauthorized_Load
T.Bad_Activation
T.TOE_Identification_Forgery
T.Pre_Perso
T.Perso
Organisational Security Policies
P.CSP_QCert P.CSP_QCert
P.QSign P.QSign
P.Sigy_SSCD P.Sigy_SSCD
P.Sig_Non-Repud P.Sig_Non-Repud
Assumptions
A.CGA A.CGA
A.SCA A.SCA
Security Objectives for the TOE
OT.Lifecycle_Security OT.Lifecycle_Security
OT.SCD/SVD_Auth_Gen OT.SCD/SVD_Auth_Gen
OT.SCD_Unique OT.SCD_Unique
OT.SCD_SVD_Corresp OT.SCD_SVD_Corresp
OT.SCD_Secrecy OT.SCD_Secrecy
OT.Sig_Secure OT.Sig_Secure
OT.Sigy_SigF OT.Sigy_SigF
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
OT.DTBS_Integrity_TOE OT.DTBS_Integrity_TOE
OT.EMSEC_Design OT.EMSEC_Design
OT.Tamper_ID OT.Tamper_ID
OT.Tamper_Resistance OT.Tamper_Resistance
OT.Secure_Load_ACode
OT.Secure_AC_Activation
OT.TOE_Identification
OT.Pre_Perso
OT.Perso
Security Objectives for Operational Environment
OE.SVD_Auth OE.SVD_Auth
OE.CGA_QCert OE.CGA_QCert
OE.SSCD_Prov_Service OE.SSCD_Prov_Service
OE.HID_VAD OE.HID_VAD
OE.DTBS_Intend OE.DTBS_Intend
OE.DTBS_Protect OE.DTBS_Protect
OE.Signatory OE.Signatory
Table 5-2 - Conformance with SSCD-2 PP (SPD and Objectives)
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
5.2.1 Correspondences and additions of SFR
SFRs from PP SSCD – 2 SFRs from ST
FCS_CKM.1 FCS_CKM.1/RSA
FCS_CKM.1/ECDSA
FCS_CKM.1/MP_Add_code
FCS_CKM.1/MP
FCS_CKM.4 FCS_CKM.4
FCS_COP.1 FCS_COP.1
FCS_COP.1/MP_ENC_Add_code
FCS_COP.1/MP_MAC_Add_code
FCS_COP.1/MP_ENC_3DES
FCS_COP.1/MP_ENC_AES
FCS_COP.1/MP_MAC_3DES
FCS_COP.1/MP_MAC_AES
FCS_COP.1/MP_AUTH_3DES
FCS_COP.1/MP_AUTH_AES
FCS_COP.1/MP_SHA
FDP_ACC.1/SCD/SVD_Generation FDP_ACC.1/SCD/SVD_Generation
FDP_ACC.2/MP
FDP_ACF.1/SCD/SVD_Generation FDP_ACF.1/SCD/SVD_Generation
FDP_ACF.1/MP
FDP_ACC.1/SVD_Transfer FDP_ACC.1/SVD_Transfer
FDP_ACF.1/SVD_Transfer FDP_ACF.1/SVD_Transfer
FDP_ACC.1/Signature_Creation FDP_ACC.1/Signature_Creation
FDP_ACF.1/Signature creation FDP_ACF.1/Signature creation
FDP_RIP.1 FDP_RIP.1
FDP_SDI.2/Persistent FDP_SDI.2/Persistent
FDP_SDI.2/DTBS FDP_SDI.2/DTBS
FDP_UCT.1/MP
FDP_UIT.1/MP
FDP_UIT.1/MP_Add_code
FIA_UID.1 FIA_UID.1
FIA_UID.1/MP
FIA_UAU.1 FIA_UAU.1
FIA_UAU.1/MP
FIA_UAU.4/MP_3DES
FIA_UAU.4/MP_AES
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
SFRs from PP SSCD – 2 SFRs from ST
FIA_UAU.5/MP_3DES
FIA_UAU.5/MP_AES
FIA_AFL.1 FIA_AFL.1
FIA_AFL.1/MP
FMT_SMR.1 FMT_SMR.1
FMT_SMR.1/MP_Add_Code
FMT_SMR.1/MP
FMT_SMF.1 FMT_SMF.1
FMT_SMF.1/MP
FMT_MOF.1 FMT_MOF.1
FMT_MSA.1/Admin FMT_MSA.1/Admin
FMT_MSA.1/Signatory FMT_MSA.1/Signatory
FMT_MSA.2 FMT_MSA.2
FMT_MSA.3 FMT_MSA.3
FMT_MSA.4 FMT_MSA.4
FMT_MTD.1/Admin FMT_MTD.1/Admin
FMT_MTD.1/Signatory FMT_MTD.1/Signatory
FMT_MTD.1/MP_Add_code
FMT_MTD.1/MP_KEY_READ_Add_code
FMT_MTD.1/MP
FMT_MTD.1/MP_INI_ENA
FMT_MTD.1/MP_INI_DIS
FMT_MTD.1/MP_KEY_READ
FMT_MTD.1/MP_KEY_WRITE
FPT_EMS.1 FPT_EMS.1
FPT_EMS.1/MP_Add_code
FPT_EMS.1/MP
FPT_FLS.1 FPT_FLS.1
FPT_PHP.1 FPT_PHP.1
FPT_PHP.3 FPT_PHP.3
FPT_TST.1 FPT_TST.1
FTP_ITC.1/MP_Add_code
FTP_ITC.1/MP
FDP_ITC.1/MP
FAU_SAS.1/MP
FAU_STG.2/MP_Add_Code
Table 5-3 - Conformance with SSCD-2 PP (SFR)
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
6 SECURITY PROBLEM DEFINITION
6.1 Assets, objects, users and subjects
The assets, objects, users and subjects appearing in the rest of the Security Target are being introduced in
this section.
6.1.1 Assets and objects
6.1.1.1 From PP SSCD-2
1. SCD: private key used to perform an electronic signature operation. The confidentiality, integrity
and signatory’s sole control over the use of the SCD must be maintained.
SCD key is an asset of “operational use” phase.
2. SVD: public key linked to the SCD and used to perform electronic signature verification. The
integrity of the SVD when it is exported must be maintained.
SVD key is an asset of “operational use” phase.
3. DTBS and DTBS/R: set of data, or its representation, which the signatory intends to sign. Their
integrity and the unforgeability of the link to the signatory provided by the electronic signature
must be maintained.
DTBS and DTBS/R are assets of the “Operational Use” phase.
6.1.1.2 Others
4. TOE ID: Data uniquely identifying the TOE.
TOE ID is an asset of the “pre-personalization” and “personalization” phases.
5. CPLC data: Card Personalization Life Cycle data
CPLC is an asset of the “pre-personalization” and “personalization” phases.
6. RAD: Reference Authentication Data
RAD is an asset of the “personalization” and “operational use” phases.
7. Pre-personalization / Personalization keys (including LSK, MSK, DEC, ENC, MAC, keys used for
Secure Messaging)
These keys are used for encrypting and charging of additional code and keys during the Pre-
personalization and Personalization phases. They count as sensitive data.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
6.1.2 Users and subjects acting for users
6.1.2.1 From PP SSCD - 2
1. User: End user of the TOE who can be identified as administrator or signatory. The subject S.User
may act as S.Admin in the role R.Admin or as S.Sigy in the role R.Sigy.
2. Administrator: User who is in charge to perform the TOE initialisation, TOE (pre-) personalization or
other TOE administrative functions. The subject S.Admin is acting in the role R.Admin for this user
after successful authentication as administrator. The CSP (Certificate Service Provider) also counts
as Administrator.
3. Signatory: User who holds the TOE and uses it on their own behalf or on behalf of the natural or
legal person or entity they represent. The subject S.Sigy is acting in the role R.Sigy for this user after
successful authentication as signatory.
6.1.2.2 Others
4. Manufacturer: The person that produces the TOE. He will act in the role Manufacturer.
5. Pre-personalizer: This is a refinement of the Administrator and describes the person that is
specifically in charge of Pre-personalization.
6. Personalizer: This is a refinement of the Administrator and describes the person that is specifically
in charge of Personalization.
6.2 Threats
The threats for the TOE are introduced in this section, beginning with the definition of the threat agents.
6.2.1 Threat agents
6.2.1.1 From PP SSCD - 2
1. Attacker in operational use phase: Human or process acting on their behalf located outside the
TOE. The main goal of the attacker is to access the SCD or to falsify the electronic signature. The
attacker has got a high attack potential and knows no secret.
6.2.1.2 Others
2. Attacker in pre-personalization or personalisation phases: human or process acting on their behalf
located outside the TOE. The goal of the attacker is to read or modify the TOE pre-personalisation
and personalization data that he does not have the right to read or modify (sensitive data), or to
forge the additional code. The attacker has got a high attack potential.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
6.2.2 Threats from PP SSCD - 2
6.2.2.1 T.SCD_Divulg Storing, copying and releasing of the signature creation
data
An attacker stores or copies the SCD outside the TOE. An attacker can obtain the SCD during generation,
storage and use for signature creation in the TOE.
6.2.2.2 T.SCD_Derive Derive the signature creation data
An attacker derives the SCD from publicly known data, such as SVD corresponding to the SCD or signatures
created by means of the SCD or any other data exported outside the TOE, which is a threat against the
secrecy of the SCD.
6.2.2.3 T.Hack_Phys Physical attacks through the TOE interfaces
An attacker interacts physically with the TOE to exploit vulnerabilities, resulting in arbitrary security
compromises. This threat is directed against SCD, SVD and DTBS.
6.2.2.4 T.SVD_Forgery Forgery of the signature verification data
An attacker forges the SVD presented by the CSP to the CA. This results in loss of SVD integrity in the
certificate of the signatory.
6.2.2.5 T.SigF_Misuse Misuse of the signature creation function of the TOE
An attacker misuses the signature creation function of the TOE to create SOD for data the signatory has not
decided to sign. The TOE is subject to deliberate attacks by experts possessing a high attack potential with
advanced knowledge of security principles and concepts employed by the TOE.
6.2.2.6 T.DTBS_Forgery Forgery of the DTBS/R
An attacker modifies the DTBS/R sent by the SAC. Thus the DTBS/R used by the TOE for signing does not
match the DTBS the signatory intended to sign.
6.2.2.7 T.Sig_Forgery Forgery of the electronic signature
An attacker forges a signed data object, maybe using an electronic signature, which has been created by the
TOE, and the violation of the integrity of the signed data object is not detectable by the signatory or by third
parties. The signature created by the TOE is subject to deliberate attacks by experts possessing a high attack
potential with advanced knowledge of security principles and concepts employed by the TOE.
6.2.3 Threats for Loading of Additional Code
6.2.3.1 T.Unauthorized_Load
Adverse action: An attacker tries to load an additional code that is not intended to be assembled with the
initial TOE, i.e. the evidence of authenticity or integrity is not correct.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
Threat agent: having high attack potential, knowing the MSK, LSK and derivation data, being in possession
of a legitimate eSign card
Asset: RAD
6.2.3.2 T.Bad_Activation
Adverse action: An attacker tries to perturbate the additional code activation such that the final TOE is
different than the expected one (initial TOE or perturbated TOE).
Threat agent: having high attack potential, knowing the MSK, LSK and derivation data, being in possession
of a legitimate eSign card, being in possession of an additional code that is authorized to be loaded
Asset: RAD
6.2.3.3 T.TOE_Identification_Forgery
Adverse action: An attacker tries to perturb the TOE identification and in particular the additional code
identification.
Threat agent: having high attack potential, being in possession of a legitimate eSign card.
Asset: TOE ID
Application Note: This threat is not applicable in phase 7, as the TOE identification is not possible in
phase 7.
6.2.4 Threats for pre-personalization and personalization
6.2.4.1 T.Pre_Perso
Adverse action: An attacker tries to read or modify TOE assets available in pre-personalization phase that he
does not have the right to read or modify (sensitive data).
Threat agent: having high attack potential, being in possession of a legitimate eSign card.
Assets: CPLC data, TOE-ID.
6.2.4.2 T.Perso
Adverse action: An attacker tries to read or modify TOE assets available in personalization phase that he
does not have the right to read or modify (sensitive data).
Threat agent: having high attack potential, being in possession of a legitimate eSign card.
Assets: CPLC data, TOE-ID, RAD.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
6.3 Organizational security policies
6.3.1 Organizational Security Policies from the PP SSCD – 2
6.3.1.1 P.CSP_QCert Qualified certificate
The CSP uses a trustworthy CGA to generate a qualified certificate or non-qualified certificate (cf. the
directive, article 2, clause 9, and Annex I) for the SVD generated by the SSCD. The certificates contain at
least the name of the signatory and the SVD matching the SCD implemented in the TOE under sole control
of the signatory. The CSP ensures that the use of the TOE as SSCD is evident with signatures through the
certificate or other publicly available information.
6.3.1.2 P.QSign Qualified electronic signatures
The signatory uses a signature creation system to sign data with an advanced electronic signature (cf. the
directive, article 1, clause 2), which is a qualified electronic signature if it is based on a valid qualified
certificate (according to the directive Annex I)1
. The DTBS are presented to the signatory and sent by the
SCA as DTBS/R to the SSCD. The SSCD creates the electronic signature created with a SCD implemented in
the SSCD that the signatory maintain under their sole control and is linked to the DTBS/R in such a manner
that any subsequent change of the data is detectable.
6.3.1.3 P.Sigy_SSCD TOE as secure signature creation device
The TOE meets the requirements for an SSCD laid down in Annex III of the directive [1]. This implies the SCD
is used for digital signature creation under sole control of the signatory and the SCD can practically occur
only once.
6.3.1.4 P.Sig_Non-Repud Non-repudiation of signatures
The life cycle of the SSCD, the SCD and the SVD shall be implemented in a way that the signatory is not able
to deny having signed data if the signature is successfully verified with the SVD contained in their
unrevoked certificate.
1
It is a non-qualified advanced electronic signature if it is based on a non-qualified certificate for the SVD.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
6.4 Assumptions
6.4.1 Assumptions from the PP SSCD – 2
6.4.1.1 A.CGA Trustworthy certificate generation application
The CGA protects the authenticity of the signatory’s name or pseudonym and the SVD in the (qualified)
certificate by an advanced electronic signature of the CSP.
6.4.1.2 A.SCA Trustworthy signature creation application
The signatory uses only a trustworthy SCA. The SCA generates and sends the DTBS/R of the data the
signatory wishes to sign in a form appropriate for signing by the TOE.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
7 SECURITY OBJECTIVES
7.1 Security Objectives for the TOE
7.1.1 Security Objectives from PP SSCD - 2
7.1.1.1 Relation to PP SSCD KI
Security objectives for the TOE in this PP, which are identically stated in the PP SSCD KI, are
OT.Lifecycle_Security, OT.SCD_Secrecy, OT.Sig_Secure, OT.Sigy_SigF, OT.DTBS_Integrity_TOE,
OT.EMSEC_Design, OT.Tamper_ID and OT.Tamper_Resistance (these are independent from the fact
whether SCD are generated by the TOE itself or imported from the operational environment).
The remaining security objectives for the TOE OT.SCD/SVD_Auth_gen, OT.SCD_Unique and
OT.SCD_SVD_Corresp cover different aspects of the SCD/SVD generation by the TOE and are not present in
PP SSCD KI. Instead, in PP SSCD KI the analogous security objectives for the operational environment
OE.SCD/SVD_Auth_gen, OE.SCD_Unique and OE.SCD_SVD_Corresp are defined, as with key import the
operational environment is responsible for the key generation.
7.1.1.2 OT.Lifecycle_Security Lifecycle security
The TOE shall detect flaws during the initialisation, personalisation and operational usage. The TOE shall
securely destroy the SCD on demand of the signatory.
The TOE only contains one set of SCD at a time.
7.1.1.3 OT.SCD/SVD_Auth_Gen Authorized SCD/SVD generation
The TOE shall provide security features to ensure that authorized users only may invoke the generation of
the
SCD and the SVD.
7.1.1.4 OT.SCD_Unique Uniqueness of the signature creation data
The TOE shall ensure the cryptographic quality of an SCD/SVD pair it creates as suitable for the advanced or
qualified electronic signature. The SCD used for signature creation shall practically occur only once and shall
not be reconstructable from the SVD. In that context ‘practically occur once’ means that the probability of
equal SCDs is negligible.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
7.1.1.5 OT.SCD_SVD_Corresp Correspondence between SVD and SCD
The TOE shall ensure the correspondence between the SVD and the SCD generated by the TOE. This
includes unambiguous reference of a created SVD/SCD pair for export of the SVD and in creating an
electronic signature creation with the SCD.
7.1.1.6 OT.SCD_Secrecy Secrecy of the signature creation data
The secrecy of the SCD (used for signature creation) shall be reasonably assured against attacks with a high
attack potential.
7.1.1.7 OT.Sig_Secure Cryptographic security of the electronic signature
The TOE shall create digital signatures that cannot be forged without knowledge of the SCD through robust
encryption techniques. The SCD shall not be reconstructable using the digital signatures or any other data
exportable from the TOE. The digital signatures shall be resistant against these attacks, even when
executed with a high attack potential.
7.1.1.8 OT.Sigy_SigF Signature creation function for the legitimate signatory
only
The TOE shall provide the digital signature creation function for the legitimate signatory only and protects
the SCD against the use of others. The TOE shall resist attacks with high attack potential.
7.1.1.9 OT.DTBS_Integrity_TOE DTBS/R integrity inside the TOE
The TOE must not alter the DTBS/R. As by definition of the DTBS/R this may consist of the DTBS themselves,
this objective does not conflict with a signature creation process where the TOE hashes the provided DTBS
(in part or entirely) for signature creation.
7.1.1.10 OT.EMSEC_Design Provide physical emanations security
The TOE shall be designed and built in such a way as to control the production of intelligible emanations
within specified limits.
7.1.1.11 OT.Tamper_ID Tamper detection
The TOE shall provide system features that detect physical tampering of its components, and uses those
features to limit security breaches.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
7.1.1.12 OT.Tamper_Resistance Tamper resistance
The TOE shall prevent or resist physical tampering with specified system devices and components.
7.1.2 Security Objectives for the Loading of Additional Code
7.1.2.1 OT.Secure_Load_ACode
The Loader of the Initial TOE shall check an evidence of authenticity and integrity of the loaded Additional
Code. The Loader enforces that only the allowed version of the Additional Code can be loaded on the Initial
TOE. The Loader shall forbid the loading of an Additional Code not intended to be assembled with the Initial
TOE.
During the Load Phase of an Additional Code, the TOE shall remain secure.
7.1.2.2 OT.Secure_AC_Activation
Activation of the Additional Code and update of the Identification Data shall be performed at the same time
in an Atomic way. All the operations needed for the code to be able to operate as in the Final TOE shall be
completed before activation. If the Atomic Activation is successful, then the resulting product is the Final
TOE, otherwise (in case of interruption or incident which prevents the forming of the Final TOE), the Initial
TOE shall remain in its initial state or fail secure.
7.1.2.3 OT.TOE_Identification
The Identification Data identifies the Initial TOE and Additional Code. The TOE provides means to store
Identification Data in its non-volatile memory and guarantees the integrity of these data. After Atomic
Activation of the Additional Code, the Identification Data of the Final TOE allows identifications of Initial
TOE and Additional Code. The user must be able to uniquely identify Initial TOE and Additional Code(s)
which are embedded in the Final TOE. TOE must support the terminal to verify the authenticity.
7.1.3 Security Objectives for pre-personalization and personalization
7.1.3.1 OT.Pre_Perso
The TOE must protect the stored data from unauthorized disclosure or modification. Sensitive data cannot
be read nor modified by anyone else than the pre-personalizer. The TOE shall protect sensitive data against
unauthorized disclosure or modification by logical or physical means. To perform any operation on sensitive
data, the pre-personalizer shall be authenticated. He may use secure messaging to exchange data with the
TOE. The loading of the keys is always executed encrypted with the DEC key, and optionally with additional
SM.
The code is always loaded during the pre-personalization phase encrypted with the LSK key.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
7.1.3.2 OT.Perso
The TOE must protect the stored data from unauthorized disclosure or modification. Sensitive data cannot
be read or modified by anyone else than the personalizer. The TOE shall protect sensitive data against
unauthorized disclosure or modification by logical or physical means. To perform any operation on sensitive
data, the personalizer shall be authenticated. He may use secure messaging to exchange data with the TOE.
The loading of the keys is always executed encrypted with the DEC key, and optionally with additional SM.
7.2 Security objectives for the operational environment
7.2.1 Security objectives from PP SSCD-2
7.2.1.1 Relation to PP SSCD-3 KI (key import)
Security objectives for the operational environment in this PP, which are identically stated in the PP SSCD
KI, are OE.SVD_Auth, OE.CGA_QCert, OE.SSCD_Prov_Service, OE.HID_VAD, OE.DTBS_Intend,
OE.DTBS_Protect and OE.Signatory (these are independent from the fact whether SCD are generated by the
TOE itself or imported from the operational environment).
7.2.1.2 OE.SVD_Auth Authenticity of the SVD
The operational environment shall ensure the integrity of the SVD sent to the CGA of the CSP. The CGA
verifies the correspondence between the SCD in the SSCD of the signatory and the SVD in the qualified
certificate.
7.2.1.3 OE.CGA_QCert Generation of qualified certificates
The CGA shall generate a qualified certificate that includes (amongst others)
(a) the name of the signatory controlling the TOE,
(b) the SVD matching the SCD stored in the TOE and being under sole control of the signatory,
(c) the advanced signature of the CSP.
The CGA shall confirm with the generated qualified certificate that the SCD corresponding to the SVD is
stored in a SSCD.
7.2.1.4 OE.SSCD_Prov_Service Authentic SSCD provided by SSCD-provisioning service
The SSCD-provisioning service shall initialize and personalize for the signatory an authentic copy of the TOE
and deliver this copy as SSCD to the signatory.
7.2.1.5 OE.HID_VAD Protection of the VAD
If an external device provides the human interface for user authentication, this device shall ensure
confidentiality and integrity of the VAD as needed by the authentication method employed from import
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
through its human interface until import through the TOE interface. In particular, if the TOE requires a
trusted channel for import of the VAD, the HID shall support usage of this trusted channel.
7.2.1.6 OE.DTBS_Intend SCA sends data intended to be signed
The signatory shall use a trustworthy SCA that
- generates the DTBS/R of the data that has been presented as DTBS and which the signatory intends
to sign in a form which is appropriate for signing by the TOE,
- sends the DTBS/R to the TOE and enables verification of the integrity of the DTBS/R by the TOE,
- attaches the signature produced by the TOE to the data or provides it separately.
7.2.1.7 OE.DTBS_Protect SCA protects the data intended to be signed
The operational environment shall ensure that the DTBS/R cannot be altered in transit between the SCA
and the TOE. In particular, if the TOE requires a trusted channel for import of the DTBS/R, the SCA shall
support usage of this trusted channel.
7.2.1.8 OE.Signatory Security obligation of the signatory
The signatory shall check that the SCD stored in the SSCD received from SSCD-provisioning service is in non-
operational state. The signatory shall keep their VAD confidential.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
8 EXTENDED COMPONENTS DEFINITION
8.1 Definition of the Family FPT_EMS
The additional family FPT_EMS (TOE Emanation) of the Class FPT (Protection of the TSF) is defined here to
describe the IT security functional requirements of the TOE. The TOE shall prevent attacks against the SCD
and other secret data where the attack is based on external observable physical phenomena of the TOE.
Examples of such attacks are evaluation of TOE’s electromagnetic radiation, simple power analysis (SPA),
differential power analysis (DPA), timing attacks, radio emanation etc. This family describes the functional
requirements for the limitation of intelligible emanations. The family FPT_EMS belongs to the Class FPT
because it is the class for TSF protection. Other families within the Class FPT do not cover the TOE
emanation. The definition of the family FPT_EMS is taken from the Protection Profile Secure Signature
Creation Device [5].
FPT_EMS TOE Emanation
Family behavior: This family defines requirements to mitigate intelligible emanations.
Component leveling:
FPT_EMS.1 TOE Emanation has two constituents:
- FPT_EMS.1.1 Limit of Emissions requires to not emitting intelligible emissions enabling access to
TSF data or user data.
- FPT_EMS.1.2 Interface Emanation requires to not emitting interface emanation enabling access to
TSF data or user data.
Management: FPT_EMS.1
There are no management activities foreseen.
Audit: FPT_EMS.1
There are no actions identified that shall be auditable if FAU_GEN (Security audit data generation)
is included in a PP or ST using FPT_EMS.1.
FPT_EMS.1 TOE Emanation
Hierarchical to: No other components.
FPT_EMS TOE Emanation 1
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
Dependencies: No dependencies.
FPT_EMS.1.1
The TOE shall not emit [assignment: types of emissions] in excess of [assignment: specified limits]
enabling access to [assignment: list of types of TSF data] and [assignment: list of types of user data].
FPT_EMS.1.2
The TSF shall ensure [assignment: type of users] are unable to use the following interface
[assignment: type of connection] to gain access to [assignment: list of types of TSF data] and
[assignment: list of types of user data].
8.2 Definition of the Family FAU_SAS
To define the security functional requirements of the TOE an additional family (FAU_SAS) of the Class FAU
(Security Audit) is defined here. This family describes the functional requirements for the storage of audit
data. It has a more general approach than FAU_GEN, because it does not necessarily require the data to be
generated by the TOE itself and because it does not give specific details of the content of the audit records.
The family “Audit data storage (FAU_SAS)” is specified as follows.
FAU_SAS Audit data storage
Family behavior: This family defines functional requirements for the storage of the audit data
Component leveling:
FAU_SAS.1 Requires the TOE to provide the possibility to store audit data
Management: FAU_SAS.1 There are no management activities foreseen
Audit: FAU_SAS.1 There are no actions defined to be auditable
FAU_SAS.1 Audit storage
Hierarchical to: No other components
Dependencies: No Dependencies
FAU_SAS Audit data
storage
1
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
FAU_SAS.1.1 The TSF shall provide [assignment: list of subjects] with the capability to
store [assignment: list of audit information] in the [assignment: type of
persistent memory]
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
9 SECURITY REQUIREMENTS
9.1 Security functional requirements from PP SSCD – 2
Underlined parts correspond to instantiations, where the ones referenced by a footnote are the
instantiations of this Security Target and the ones without instantiations of the Protection Profile.
Bold parts correspond to editorial refinements.
9.1.1 Cryptographic support (FCS)
9.1.1.1 FCS_CKM.1/RSA Cryptographic key generation
Hierarchical to: No other components.
Dependencies: [FCS_CKM.2 Cryptographic key distribution, or
FCS_COP.1 Cryptographic operation]
FCS_CKM.4 Cryptographic key destruction
FCS_CKM.1.1/RSA The TSF shall generate an SCD/SVD pair in accordance with a specified
cryptographic key generation algorithm RSA key generation and specified
cryptographic key sizes RSA 1024 to 4096 bits in steps of 256 bits2
that meet the
following:
 FIPS 186.3
9.1.1.2 FCS_CKM.1/ECDSA Cryptographic key generation
Hierarchical to: No other components.
Dependencies: [FCS_CKM.2 Cryptographic key distribution, or
FCS_COP.1 Cryptographic operation]
FCS_CKM.4 Cryptographic key destruction
FCS_CKM.1.1/ECDSA The TSF shall generate an SCD/SVD pair in accordance with a specified
cryptographic key generation algorithm ECDSA key generation and specified
cryptographic key sizes 192 up to 521 bits where the field length of a given elliptic
curve is used to determine the maximum length of signature’s input, where the
field length L is computed as follows:
2
[assignment: cryptographic key sizes]
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
L = [log256 N] = (N size in bits) / 8 = N size in bytes
Where N is the elliptic curve’s order.3
These are keys that meet the following:
 ECDSA – Elliptic Curve Digital Signature Scheme (TR 3111),
 FIPS 186-4.
9.1.1.3 FCS_CKM.4 Cryptographic key destruction
Hierarchical to: No other components.
Dependencies: [FDP_ITC.1 Import of user data without security attributes, or
FDP_ITC.2 Import of user data with security attributes, or
FCS_CKM.1 Cryptographic key generation]
FCS_CKM.4.1 The TSF shall destroy cryptographic keys in accordance with a specified
cryptographic key destruction method zeroisation4
that meets the following: none5
.
9.1.1.4 FCS_COP.1 Cryptographic operation
Hierarchical to: No other components.
Dependencies: [FDP_ITC.1 Import of user data without security attributes, or
FDP_ITC.2 Import of user data with security attributes, or
FCS_CKM.1 Cryptographic key generation]
FCS_CKM.4 Cryptographic key destruction
FCS_COP.1.1 The TSF shall perform digital signature creation in accordance with a specified
cryptographic algorithm
 Hash: SHA1, SHA224, SHA256, SHA384, SHA512
 Signature based on RSA and elliptic curve signature scheme:
o RSA PKCS#v1.5
o RSA PSS
 Without the following combinations:
o ESIGN_RSA_PKCS#v1.5_1024_SHA384
3
[assignment: cryptographic key sizes]
4
[assignment: cryptographic key destruction method]
5
[assignment: list of standards].
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
o ESIGN_RSA_PKCS#v1.5_1024_SHA512
o ESIGN_RSA_PKCS#v1.5_1280_SHA512
o ESIGN_RSA_PKCS#v1.5_1536_SHA512
 Signature based on Elliptic curves signature schemes:
o ECDSA plain
o ECDSA BER-TLV
and cryptographic key sizes RSA 1024 to 4096 bits in steps of 256 bits and EC 192
up to 521 bits that meet the following:
 RSA Digital Signature Schemes with Appendix (RSA labs)
o PKCS version 1.5 RSASSA-PKCSv1_5
o PKCS version 2.1 Probabilistic Signature Scheme RSASSA-PSS
 ECDSA – Elliptic Curve Digital Signature Scheme (TR 3111)
o Plain format
o X9.62 format6
.
9.1.2 User data protection (FDP)
The security attributes and related status for the subjects and objects are:
Subject or object the security
attribute is associated with
Security attribute type Value of the security attribute
S.User
Role R.Admin
R.Sigy
SCD/SVD Management Authorized
Not authorized
SCD
SCD Operational No
Yes
SCD identifier Arbitrary value
SVD (This ST does not define security
attributes for SVD)
(This ST does not define security
attributes for SVD)
9.1.2.1 FDP_ACC.1/SCD/SVD_Generation Subset access control
Hierarchical to: No other components.
Dependencies: FDP_ACF.1 Security attribute based access control
FDP_ACC.1.1/SCD/SVD_Generation The TSF shall enforce the SCD/SVD Generation SFP on
6
[assignment: list of standards]
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
(1) subjects: S.User,
(2) objects: SCD, SVD,
(3) operations: generation of SCD/SVD pair.
9.1.2.2 FDP_ACF.1/SCD/SVD_Generation Security attribute based access control
Hierarchical to: No other components.
Dependencies: FDP_ACC.1 Subset access control
FMT_MSA.3 Static attribute initialization
FDP_ACF.1.1/SCD/SVD_Generation The TSF shall enforce the SCD/SVD Generation SFP to objects based
on the following: the user S.User is associated with the security
attribute “SCD/SVD Management“.
FDP_ACF.1.2/ SCD/SVD_Generation The TSF shall enforce the following rules to determine if an
operation among controlled subjects and controlled objects is
allowed:
S.User with the security attribute “SCD/SVD Management” set to
“authorized” is allowed to generate SCD/SVD pair.
FDP_ACF.1.3/ SCD/SVD_Generation The TSF shall explicitly authorize access of subjects to objects
based on the following additional rules: none.
FDP_ACF.1.4/ SCD/SVD_Generation The TSF shall explicitly deny access of subjects to objects based on
the following additional rules:
S.User with the security attribute “SCD/SVD management” set to
“not authorized” is not allowed to generate SCD/SVD pair.
9.1.2.3 FDP_ACC.1/SVD_Transfer Subset access control
Hierarchical to: No other components.
Dependencies: FDP_ACF.1 Security attribute based access control
FDP_ACC.1.1/ SVD_Transfer The TSF shall enforce the SVD Transfer SFP on
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
(1) subjects: S.User,
(2) objects: SVD
(3) operations: export.
9.1.2.4 FDP_ACF.1/SVD_Transfer Security attribute based access control
Hierarchical to: No other components.
Dependencies: FDP_ACC.1 Subset access control
FMT_MSA.3 Static attribute initialization
FDP_ACF.1.1/ SVD_Transfer The TSF shall enforce the SVD Transfer SFP to objects based on the
following:
(1) the S.User is associated with the security attribute Role,
(2) the SVD.
FDP_ACF.1.2/ SVD_Transfer The TSF shall enforce the following rules to determine if an
operation among controlled subjects and controlled objects is
allowed: R.Admin is allowed to export SVD.
FDP_ACF.1.3/ SVD_Transfer The TSF shall explicitly authorize access of subjects to objects
based on the following additional rules: none.
FDP_ACF.1.4/ SVD_Transfer The TSF shall explicitly deny access of subjects to objects based on
the following additional rules: none.
Application note: The CSP (Certificate Service Provider) is a refinement of R.Admin and the one responsible
for fulfilling the SFR.
9.1.2.5 FDP_ACC.1/Signature_Creation Subset access control
Hierarchical to: No other components
Dependencies: FDP_ACF.1 Security attribute based access control
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
FDP_ACC.1.1/Signature_Creation The TSF shall enforce the Signature Creation SFP on
(1) subjects: S.User,
(2) objects: DTBS/R, SCD,
(3) operations: signature creation.
9.1.2.6 FDP_ACF.1/Signature creation Security attribute based access control
Hierarchical to:No other components.
Dependencies: FDP_ACC.1 Subset access control
FMT_MSA.3 Static attribute initialisation
FDP_ACF.1.1/ Signature_Creation The TSF shall enforce the Signature Creation SFP to objects based
on the following:
(1) the user S.User is associated with the security attribute
“Role” and
(2) the SCD with the security attribute “SCD Operational”.
FDP_ACF.1.2/ Signature_Creation The TSF shall enforce the following rules to determine if an
operation among controlled subjects and controlled objects is
allowed:
R.Sigy is allowed to create electronic signatures for DTBS/R with
SCD which security attribute “SCD operational” is set to “yes”.
FDP_ACF.1.3/ Signature_Creation The TSF shall explicitly authorize access of subjects to objects
based on the following additional rules: none.
FDP_ACF.1.4/ Signature_Creation The TSF shall explicitly deny access of subjects to objects based on
the following additional rules:
S.User is not allowed to create electronic signatures for DTBS/R
with SCD which security attribute “SCD operational” is set to “no”.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
9.1.2.7 FDP_RIP.1 Subset residual information protection
Hierarchical to: No other components
Dependencies: No dependencies
FDP_RIP.1.1 The TSF shall ensure that any previous information content of a
resource is made unavailable upon the de-allocation of the
resource from the following objects: SCD.
9.1.2.8 FDP_SDI.2/Persistent Stored data integrity monitoring and action
Hierarchical to:FDP_SDI.1 Stored data integrity monitoring.
Dependencies: No dependencies.
FDP_SDI.2.1/ Persistent The TSF shall monitor user data stored in containers controlled by
the TSF for integrity error on all objects, based on the following
attributes: integrity checked stored data.
FDP_SDI.2.2/ Persistent Upon detection of a data integrity error, the TSF shall
(1) prohibit the use of the altered data
(2) inform the S.Sigy about integrity error.
Application note: The following data persistently stored by the TOE has the user data attribute "integrity
checked persistent stored data":
1. SCD
2. SVD
9.1.2.9 FDP_SDI.2/DTBS Stored data integrity monitoring and action
Hierarchical to: FDP_SDI.1 Stored data integrity monitoring.
Dependencies: No dependencies.
FDP_SDI.2.1/DTBS The TSF shall monitor user data stored in containers controlled by
the TSF for integrity error on all objects, based on the following
attributes: integrity checked stored DTBS.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
FDP_SDI.2.2/DTBS Upon detection of a data integrity error, the TSF shall
(1) prohibit the use of the altered data
(2) inform the S.Sigy about integrity error.
Application note: The DTBS/R temporarily stored by the TOE has the user data attribute "integrity checked
stored data".
9.1.3 Identification and authentication (FIA)
9.1.3.1 FIA_UID.1 Timing of identification
Hierarchical to: No other components.
Dependencies: No dependencies.
FIA_UID.1.1 The TSF shall allow
1) Self-test according to FPT_TST.1
2) Read EF.CardAccess
3) Execute Authentication Procedure (see 3.2.6.4)
4) Select File
5) Verification of the RAD7
on behalf of the user to be performed before the user is identified
FIA_UID.1.2 The TSF shall require each user to be successfully identified before
allowing any other TSF-mediated actions on behalf of that user.
9.1.3.2 FIA_UAU.1 Timing of authentication
Hierarchical to: No other components.
Dependencies: FIA_UID.1 Timing of identification.
FIA_UAU.1.1 The TSF shall allow
1) Self-test according to FPT_TST.1,
2) Identification of the user by means of TSF required by
FIA_UID.1.
7
[assignment: list of additional TSF-mediated actions]
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
on behalf of the user to be performed before the user is
authenticated.
FIA_UAU.1.2 The TSF shall require each user to be successfully authenticated
before allowing any other TSF-mediated actions on behalf of that
user.
9.1.3.3 FIA_AFL.1 Authentication failure handling
Hierarchical to: No other components.
Dependencies: FIA_UAU.1 Timing of authentication
FIA_AFL.1.1 The TSF shall detect when the allowed number fixed by the
Personalizer for8
unsuccessful authentication attempts occur
related to consecutive failed authentication attempts.
FIA_AFL .1.2 When the defined number of unsuccessful authentication attempts
has been met, the TSF shall block the RAD.
9.1.4 Security Management (FMT)
9.1.4.1 FMT_SMR.1 Security roles
Hierarchical to: No other components.
Dependencies: FIA_UID.1 Timing of identification.
FMT_SMR.1.1 The TSF shall maintain the roles R.Admin and R.Sigy.
FMT_SMR.1.2 The TSF shall be able to associate users with roles.
8
[selection: [assignment: positive integer number], an administrator configurable positive integer within [assignment: range of acceptable values]]
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
9.1.4.2 FMT_SMF.1 Security management functions
Hierarchical to: No other components.
Dependencies: No dependencies.
FMT_SMF.1.1 The TSF shall be capable of performing the following management
functions:
 Creation and modification of RAD,
 Management of data related to the Authentication Procedure
(see 3.2.6.4)
 Enabling the signature creation function,
 Modification of the security attribute SCD/SVD management,
SCD operational,
 Change the default value of the security attribute SCD
Identifier.
9.1.4.3 FMT_MOF.1 Management of security functions behavior
Hierarchical to: No other components.
Dependencies: FMT_SMR.1 Security roles
FMT_SMF.1 Specification of Management Functions.
FMT_MOF.1.1 The TSF shall restrict the ability to enable the functions signature
creation function to R.Sigy.
9.1.4.4 FMT_MSA.1/Admin Management of security attributes
Hierarchical to: No other components.
Dependencies: [FDP_ACC.1 Subset access control, or
FDP_IFC.1 Subset information flow control]
FMT_SMR.1 Security roles
FMT_SMF.1 Specification of Management Functions
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
FMT_MSA.1.1/ Admin The TSF shall enforce the SCD/SVD Generation SFP to restrict the
ability to modify9
the security attributes SCD/SVD management to
R.Admin.
9.1.4.5 FMT_MSA.1/Signatory Management of security attributes
Hierarchical to: No other components.
Dependencies: [FDP_ACC.1 Subset access control, or
FDP_IFC.1 Subset information flow control]
FMT_SMR.1 Security roles
FMT_SMF.1 Specification of Management Functions
FMT_MSA.1.1/Signatory The TSF shall enforce the Signature Creation SFP to restrict the
ability to modify the security attributes SCD operational to R.Sigy.
9.1.4.6 FMT_MSA.2 Secure security attributes
Hierarchical to: No other components
Dependencies: [FDP_ACC.1 Subset access control, or
FDP_IFC.1 Subset information flow control]
FMT_MSA.1 Management of security attributes
FMT_SMR.1 Security roles
FMT_MSA.2.1 The TSF shall ensure that only secure values are accepted for
SCD/SVD Management and SCD operational.
9.1.4.7 FMT_MSA.3 Static attribute initialisation
Hierarchical to: No other components.
Dependencies: FMT_MSA.1 Management of security attributes
FMT_SMR.1 Security roles
9
[assignment: other operations]
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
FMT_MSA.3.1 The TSF shall enforce the SCD/SVD Generation SFP, SVD Transfer
SFP and Signature Creation SFP to provide restrictive default values
for security attributes that are used to enforce the SFP.
FMT_MSA.3.2 The TSF shall allow the R.Admin to specify alternative initial values
to override the default values when an object or information is
created.
9.1.4.8 FMT_MSA.4 Security attribute value inheritance
Hierarchical to: No other components.
Dependencies: [FDP_ACC.1 Subset access control, or
FDP_IFC.1 Subset information flow control]
FMT_MSA.4.1 The TSF shall use the following rules to set the value of security
attributes:
 If S.Admin successfully generates an SCD/SVD pair without
S.Sigy being authenticated the security attribute “SCD
operational of the SCD” shall be set to “no” as a single
operation.
 If S.Sigy successfully generates an SCD/SVD pair the security
attribute “SCD operational of the SCD” shall be set to “yes” as a
single operation.
9.1.4.9 FMT_MTD.1/Admin Management of TSF data
Hierarchical to: No other components.
Dependencies: FMT_SMR.1 Security roles
FMT_SMF.1 Specification of Management Functions
FMT_MTD.1.1/Admin The TSF shall restrict the ability to create the RAD to R.Admin.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
9.1.4.10 FMT_MTD.1/Signatory Management of TSF data
Hierarchical to: No other components.
Dependencies: FMT_SMR.1 Security roles
FMT_SMF.1 Specification of Management Functions
FMT_MTD.1.1/Signatory The TSF shall restrict the ability to modify10
the RAD to R.Sigy.
9.1.5 Protection of the TSF (FPT)
9.1.5.1 FPT_EMS.1 TOE Emanation
Hierarchical to: No other components.
Dependencies: No dependencies.
FPT_EMS.1.1 The TOE shall not emit power variations, timing variations during
command execution in excess of unuseful information11
enabling
access to RAD and SCD.
FPT.EMS.1.2 The TSF shall ensure unauthorized users12
are unable to use the
following interface IC contacts13
to gain access to RAD and SCD.
9.1.5.2 FPT_FLS.1 Failure with preservation of secure state
Hierarchical to: No other components.
Dependencies: No dependencies.
10
[assignment: other operations]
11
[assignment: specified limits]
12
[assignment: type of users]
13
[assignment: type of connection]
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
FPT_FLS.1.1 The TSF shall preserve a secure state when the following types of
failures occur:
 self-test according to FPT_TST fails
 Exposure to out-of-range operating conditions that could
lead to malfunction14
9.1.5.3 FPT_PHP.1 Passive detection of physical attack
Hierarchical to: No other components.
Dependencies: No dependencies.
FPT_PHP.1.1 The TSF shall provide unambiguous detection of physical tampering
that might compromise the TSF.
FPT_PHP.1.2 The TSF shall provide the capability to determine whether physical
tampering with the TSF’s devices or TSF’s elements has occurred.
9.1.5.4 FPT_PHP.3 Resistance to physical attack
Hierarchical to: No other components.
Dependencies: No dependencies.
FPT_PHP.3.1 The TSF shall resist physical manipulation and physical probing15
to
the TSF16
by responding automatically such that the SFRs are
always enforced.
14
[assignment: list of other types of failures in the TSF]
15
[assignment: physical tampering scenarios]
16
[assignment: list of TSF devices/elements]
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
9.1.5.5 FPT_TST.1 TSF testing
Hierarchical to: No other components.
Dependencies: No dependencies.
FPT_TST.1.1 The TSF shall run a suite of self-tests
 At reset
 Before any cryptographic operation
 When accessing a Data Group or any EF
 Prior to any use of TSF data
 Before execution of any command17
to demonstrate the correct operation of the TSF.
FPT_TST.1.2 The TSF shall provide authorized users with the capability to verify
the integrity of TSF data.
FPT_TST.1.3 The TSF shall provide authorized users with the capability to verify
the integrity of TSF.
9.2 Security Functional Requirements for Manufacturing, Personalization and
Loading of Additional Code
This chapter covers the Manufacturing and Personalisation SFR. It also includes additional SFRs for the
compliance with the Loading of Additional Code.
9.2.1 SFRs for additional code
9.2.1.1 FAU_STG.2/MP_Add_code Guarantees of audit data availability
FAU_STG.2.1/MP_Add_Code The TSF shall protect the stored audit records in the audit trail from
unauthorized deletion.
FAU_STG.2.2/MP_Add_code The TSF shall be able to prevent unauthorized modifications to the
stored audit records in the audit trail.
17
[selection: during initial start-up, periodically during normal operation, at the request of the authorised user, at the conditions [assignment:
conditions under which self-test should occur]]
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
FAU_STG.2.3/MP_Add_code The TSF shall ensure that Additional code identification stored
audit records will be maintained when the following conditions
occur: failure and attack.
Application Note: Additional code is loaded with its integrity information. This integrity information is
verified by the TOE after the loading and before the writing of the identification information by calculating
the signature and comparing it to the expected value. The signature is protected in integrity through the
TOE lifecycle: At each power on, the card verifies the integrity of this signature.
9.2.1.2 FCS_CKM.1/MP_Add_code Cryptographic key generation
FCS_CKM.1.1/MP_Add_code The TSF shall generate cryptographic keys in accordance with a
specified cryptographic key generation algorithm Calculation of
LSK_LOAD, from initial LSK and derivation data entered - AES 128
ECB18
and specified cryptographic key sizes 128 bits19
that meet the
following: none20
:
9.2.1.3 FCS_COP.1/MP_ENC_Add_code Cryptographic operation
FCS_COP.1.1/MP_ENC_Add_code The TSF shall perform Decryption of the additional code (ciphered
with LSK_LOAD) and signature verification21
in accordance with a
specified cryptographic algorithm AES22
and cryptographic key sizes
128 bits23
that meet the following: [R51]24
.
9.2.1.4 FCS_COP.1/MP_MAC_Add_code Cryptographic operation
FCS_COP.1.1/MP_MAC_Add_code The TSF shall perform Secure Messaging with AES25
in accordance with a specified cryptographic algorithm AES CMAC26
18
[cryptographic key generation algorithm]
19
[key length]
20
[standard]
21
[cryptographic operation]
22
[cryptographic algorithm]
23
[cryptographic key sizes]
24
[standard]
25
[cryptographic operation]
26
[cryptographic algorithm]
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
and cryptographic key sizes 128 bits27
that meet the following:
[R51]28
.
9.2.1.5 FDP_UIT.1/MP_Add_code Data exchange integrity
FDP_UIT.1.1/MP_Add_code The TSF shall enforce the Pre-personalization access control SFP to
receive user data in a manner protected from modification errors.
FDP_UIT.1.2/MP_Add_code [Editorially Refined] The TSF shall be able to determine on receipt
of user data, whether modification of some of the pieces of the
application sent by the TOE developer has occurred.
Application Note: Modification errors should be understood as modification, substitution, unrecoverable
ordering change of data and any other integrity error that may cause the additional code to be installed on
the card to be different from the one sent by the TOE Developer. This SFR controls integrity of data import
in phase 5, including the additional code but not only.
9.2.1.6 FMT_MTD.1/MP_Add_code Management of TSF data
FMT_MTD.1.1/MP_Add_code The TSF shall restrict the ability to activate29
the additional code30
to TOE developer31
.
Application note: The Activation of the additional code modifies the TOE. This additional code is ciphered
with the LSK_LOAD (LSK and Derivation Data) and activated after the authentication of the TOE developer.
9.2.1.7 FMT_MTD.1/MP_KEY_READ_Add_code Management of TSF data
FMT_MTD.1.1/MP_KEY_READ_Add_code The TSF shall restrict the ability to read the LSK32
to none33
:
27
[cryptographic key sizes]
28
[standard]
29
[selection]
30
[list of TSF data]
31
[authorized identified roles]
32
[data]
33
[authorized identified roles]
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
9.2.1.8 FMT_SMR.1/MP_Add_Code Security roles
FMT_SMR.1.1/MP_Add_code The TSF shall maintain the roles TOE developer.
FMT_SMR.1.2/MP_Add_code The TSF shall be able to associate users with roles.
9.2.1.9 FPT_EMS.1/MP_Add_code TOE Emanation
FPT_EMS.1.1/MP_Add_code The TOE shall not emit power variations, timing variations during
command execution in excess of non-useful information enabling
access to LSK.
FPT_EMS.1.2/MP_Add_code The TSF shall ensure any unauthorized users are unable to use the
following interface smart card circuit contacts to gain access to LSK.
9.2.1.10 FTP_ITC.1/MP_Add_code Inter-TSF trusted channel
FTP_ITC.1.1/MP_Add_code The TSF shall provide a communication channel between itself and
another trusted IT product that is logically distinct from other
communication channels and provides assured identification of its
end points and protection of the channel data from modification or
disclosure.
FTP_ITC.1.2/MP_Add_code [Editorially Refined] The TSF shall permit the TOE Developer and
Pre-personalizer to initiate communication via the trusted channel.
FTP_ITC.1.3/MP_Add_code The TSF shall initiate communication via the trusted channel for
Additional code loading.
9.2.2 Manufacturing and Personalization
9.2.2.1 FCS_CKM.1/MP Cryptographic key generation
FCS_CKM.1.1/MP The TSF shall generate cryptographic keys in accordance with a
specified cryptographic key generation algorithm MSK derivation
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
from initial MSK loaded in phase 1 using SHA 25634
and specified
cryptographic key sizes 256 bits35
that meet the following: none36
.
9.2.2.2 FCS_COP.1/MP_ENC_3DES Cryptographic operation
FCS_COP.1.1/MP_ENC_3DES The TSF shall perform Secure Messaging – encryption and
decryption37
in accordance with a specified cryptographic
algorithm 3DES in CBC mode38
and cryptographic key sizes 112
bits39
that meet the following: [R48]40
9.2.2.3 FCS_COP.1/MP_ENC_AES Cryptographic operation
FCS_COP.1.1/MP_ENC_AES The TSF shall perform Secure Messaging – encryption and
decryption41
in accordance with a specified cryptographic
algorithm AES in CBC mode42
and cryptographic key sizes 128, 192
abd 256 bits43
that meet the following: [R51]44
9.2.2.4 FCS_COP.1/MP_MAC_3DES Cryptographic operation
FCS_COP.1.1/MP_MAC_3DES The TSF shall perform Secure Messaging MAC45
in accordance with
a specified cryptographic algorithm 3DES MAC46
and cryptographic
key sizes 112 bits47
that meet the following: [R15]48
34
[cryptographic key generation algorithm]
35
[key length]
36
[standard]
37
[cryptographic operation]
38
[cryptographic operation]
39
[cryptographic key sizes]
40
[standard]
41
[cryptographic operation]
42
[cryptographic operation]
43
[cryptographic key sizes]
44
[standard]
45
[cryptographic operation]
46
[cryptographic operation]
47
[cryptographic key sizes]
48
[standard]
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
9.2.2.5 FCS_COP.1/MP_MAC_AES Cryptographic operation
FCS_COP.1.1/MP_MAC_AES The TSF shall perform Secure Messaging MAC49
in accordance with
a specified cryptographic algorithm AES50
and cryptographic key
sizes 128, 192 abd 256 bits51
that meet the following: [R51]52
9.2.2.6 FCS_COP.1/MP_AUTH_3DES Cryptographic operation
FCS_COP.1.1/MP_AUTH_3DES The TSF shall perform Card Manufacturer Authentication53
in
accordance with a specified cryptographic algorithm 3DES54
and
cryptographic key sizes 112 bits55
that meet the following: [R48]56
9.2.2.7 FCS_COP.1/MP_AUTH_AES Cryptographic operation
FCS_COP.1.1/MP_AUTH_AES The TSF shall perform Card Manufacturer Authentication57
in
accordance with a specified cryptographic algorithm AES58
and
cryptographic key sizes 128, 192 and 256 bits59
that meet the
following: [R51]60
9.2.2.8 FCS_COP.1/MP_SHA Cryptographic operation
FCS_COP.1.1/MP_SHA The TSF shall perform Hashing61
in accordance with a specified
cryptographic algorithm SHA25662
and cryptographic key sizes
none63
that meet the following: [R43]64
49
[cryptographic operation]
50
[cryptographic operation]
51
[cryptographic key sizes]
52
[standard]
53
[cryptographic operation]
54
[cryptographic operation]
55
[cryptographic key sizes]
56
[standard]
57
[cryptographic operation]
58
[cryptographic operation]
59
[cryptographic key sizes]
60
[standard]
61
[cryptographic operation]
62
[cryptographic operation]
63
[cryptographic key sizes]
64
[standard]
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
9.2.2.9 FDP_ACC.2/MP Complete access control
FDP_ACC.2.1/MP The TSF shall enforce the Pre-personalization Access Control on all
subjects and all objects and all operations among subjects and
objects covered by the SFP.
FDP_ACC.2.2/MP The TSF shall ensure that all operations between any subject
controlled by the TSF and any object controlled by the TSF are
covered by an access control SFP.
Application Note: This SFR enforces access control over all the operation performed in phase 5, including
additional code loading but not only.
9.2.2.10 FDP_ACF.1/MP Security attribute based access control
FDP_ACF.1.1/MP The TSF shall enforce the Pre-personalization Access Control to
objects based on the following Pre-personalizer Authentication
(AS_AUTH_MSK_STATUS).
FDP_ACF.1.2/MP The TSF shall enforce the following rules to determine if an
operation among controlled subjects and controlled objects is
allowed: AS_AUTH_MSK_STATUS=TRUE (EXTERNAL
AUTHENTICATE).
FDP_ACF.1.3/MP The TSF shall explicitly authorize access of subjects to objects
based on the following additional rules: none.
FDP_ACF.1.4/MP The TSF shall explicitly deny access of subjects to objects based on
the following additional rules: none.
Application Note: This SFR enforces access control over all the operation in phase 5, including additional
code loading but not only.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
9.2.2.11 FDP_ITC.1/MP Import of user data without security attributes
FDP_ITC.1.1/MP The TSF shall enforce the Pre-personalization access control when
importing user data, controlled under the SFP, from outside of the
TOE.
FDP_ITC.1.2/MP The TSF shall ignore any security attributes associated with the
user data when imported from outside the TOE.
FDP_ITC.1.3/MP The TSF shall enforce the following rules when importing user data
controlled under the SFP from outside the TOE: none.
Application Note: This SFR controls import of data in phase 5, including the additional code but not
only. This SFR ensures also the MSK diversification, which is performed once, at first command, without
any security requirements preliminary to this action.
9.2.2.12 FDP_UCT.1/MP Basic data exchange confidentiality
FDP_UCT.1.1/MP The TSF shall enforce the Pre-personalization access control to
receive user data in a manner protected from unauthorized
disclosure.
Application note: For the Additional code loading access control, the LSK_LOAD is used to cipher the data
transmitted. This SFR controls confidentiality of data import in phase 5, including the additional code but
not only.
9.2.2.13 FDP_UIT.1/MP Data exchange integrity
FDP_UIT.1.1/MP The TSF shall enforce the Pre-personalization Access Control SFP to
receive user data in a manner protected from modification errors
FDP_UIT.1.2/MP [Editorially refined] The TSF shall be able to determine on receipt
of user data, whether modification of some pieces of the
application sent by the Pre-personalizer has occurred
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
9.2.2.14 FIA_AFL.1/MP Authentication failure handling
FIA_AFL.1.1/MP The TSF shall detect when 3 unsuccessful authentication attempts
occur related to authentication of Pre-personalizer and
Personalizer
FIA_AFL.1.2/MP When the defined number of unsuccessful authentication attempts
has been met, the TSF shall slow-down authentication operation
of, the Pre-Personalizer and the Personalizer.
9.2.2.15 FIA_UAU.1/MP Timing of authentication
FIA_UAU.1.1/MP The TSF shall allow GET DATA, SELECT FILE on behalf of the user to
be performed before the user is authenticated.
FIA_UAU.1.2/MP The TSF shall require each user to be successfully authenticated
before allowing any other TSF-mediated actions on behalf of that
user.
9.2.2.16 FIA_UID.1/MP Timing of identification
FIA_UID.1.1/MP The TSF shall allow GET DATA, SELECT FILE on behalf of the user to
be performed before the user is identified.
FIA_UID.1.2/MP The TSF shall require each user to be successfully identified before
allowing any other TSF-mediated actions on behalf of that user.
9.2.2.17 FIA_UAU.4/MP_3DES Single-use authentication mechanisms
FIA_UAU.4.1/MP_3DES The TSF shall prevent reuse of authentication data related to
Authentication Mechanisms based on 3DES.
9.2.2.18 FIA_UAU.4/MP_AES Single-use authentication mechanisms
FIA_UAU.4.1/MP_AES The TSF shall prevent reuse of authentication data related to
Authentication Mechanisms based on AES.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
9.2.2.19 FIA_UAU.5/MP_3DES Multiple authentication mechanisms
FIA_UAU.5.1/MP_3DES The TSF shall provide Symmetric Authentication Mechanism based
on 3DES to support user authentication.
FIA_UAU.5.2/MP_3DES The TSF shall authenticate any user's claimed identity according to
the: The TOE accepts the authentication attempt as
Personalization Agent by the Symmetric Authentication
Mechanism with the Personalization Agent Key.
9.2.2.20 FIA_UAU.5/MP_AES Multiple authentication mechanisms
FIA_UAU.5.1/MP_AES The TSF shall provide Symmetric Authentication Mechanism based
on AES to support user authentication.
FIA_UAU.5.2/MP_AES The TSF shall authenticate any user's claimed identity according to
the: The TOE accepts the authentication attempt as
Personalization Agent by the Symmetric Authentication
Mechanism with the Personalization Agent Key.
9.2.2.21 FMT_MTD.1/MP Management of TSF data
FMT_MTD.1.1/MP The TSF shall restrict the ability to switch the TOE lifecycle from
phase 5 to phase 6 to the Pre-personalizer.
9.2.2.22 FTP_ITC.1/MP Inter-TSF trusted channel
FTP_ITC.1.1/MP The TSF shall provide a communication channel between itself and
another trusted IT product that is logically distinct from other
communication channels and provides assured identification of its
end points and protection of the channel data from modification or
disclosure.
FTP_ITC.1.2/MP [Editorially Refined] The TSF shall permit the Pre-personalizer to
initiate communication via the trusted channel.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
FTP_ITC.1.3/MP The TSF shall initiate communication via the trusted channel for:
 Personalization Agent key storage
 Lifecycle transition from Pre-personalization to Personalization
phase
9.2.2.23 FMT_MTD.1/MP_INI_ENA Management of TSF data
FMT_MTD.1.1/MP_INI_ENA The TSF shall restrict the ability to write the Initialization Data and
Pre-personalization Data to the Pre-personalizer.
9.2.2.24 FMT_MTD.1/MP_INI_DIS Management of TSF data
FMT_MTD.1.1/MP_INI_DIS The TSF shall restrict the ability to disable read access for users to
the Initialization Data to the Pre-personalizer.
9.2.2.25 FMT_MTD.1/MP_KEY_READ Management of TSF data
FMT_MTD.1.1/MP_KEY_READ The TSF shall restrict the ability to read the MSK and
Personalization Agent keys to none.
9.2.2.26 FMT_MTD.1/MP_KEY_WRITE Management of TSF data
FMT_MTD.1.1/MP_KEY_WRITE The TSF shall restrict the ability to write the MSK to IC
manufacturer (created by the developer) and Personalization
Agent keys to none.
9.2.2.27 FAU_SAS.1/MP Audit storage
FAU_SAS.1.1/MP The TSF shall provide the Manufacturer with the capability to store
the IC Identification Data in the audit records.
9.2.2.28 FMT_SMF.1/MP Specification of Management Functions
FMT_SMF.1.1/MP The TSF shall be capable of performing the following management
functions:
 Initialization
 Pre-personalization
 Personalization
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
9.2.2.29 FMT_SMR.1/MP Security Roles
FMT_SMR.1.1/MP The TSF shall maintain the roles Manufacturer.
FMT_SMR.1.2/MP The TSF shall be able to associate users with roles.
9.2.2.30 FPT_EMS.1/MP TOE Emanation
FPT_EMS.1.1/MP The TOE shall not emit power variations, timing variations during
command execution in excess of non-useful information enabling
access to
1. Pre-personalizer Key
2. Personalization Agent Key
3. MSK
FPT_EMS.1.2/MP The TSF shall ensure any unauthorized users are unable to use the
following interface smart card circuit contacts to gain access to
1. Pre-personalizer Key
2. Personalization Agent Key
3. MSK
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
10 TOE SUMMARY SPECIFICATION
10.1 TOE Summary Specification
Pre-personalization
This security functionality ensures that the TOE, when delivered to the Pre-personalization Agent, provides
an authentication mechanism for data exchange. This authentication is based on Triple DES or AES
symmetric authentication mechanism. The pre-personalization function allows to
 Pre-initialize the product with CPLC data, additional code identification,
 Load and activate additional code if needed,
 Load data in clear text or with secure messaging,
 Load encrypted keys directly or through secure messaging,
 Create the eSign application,
 Load personalization authentication keys.
This functionality is conformant with [R61]. The prepersonalizer can use Secure Messaging described in the
functionality Secure Messaging to protect integrity and/or confidentiality of the communication.
Personalization
This security functionality ensures that the TOE, when delivered to the Personalization Agent, provides
authentication for data exchange. This authentication is based on a Triple DES or AES authentication
mechanism.
This personalization function allows to
 Load data in clear text or with secure messaging,
 Load encrypted keys directly or through secure messaging,
 Create the eSign application (if not performed during pre-personalization).
The personalizer can use Secure Messaging described in the functionality Secure Messaging to protect
integrity and/or confidentiality of the communication.
Secure Messaging
This security functionality ensures the confidentiality, authenticity and integrity of the communication
between the TOE and the interface device. In the operational phase, after a successful Authentication
Procedure (see 3.2.6.4), a secure channel is established.
This security functionality also provides a Secure Messaging (SCP02 and SCP03) for the pre-personalization
and personalization phases. The protocols can be configured to protect the exchanges integrity and/or
confidentiality.
If an error occurs in the secure messaging layer, the session keys are destroyed.
Access Control in reading
This function controls access to read functions and enforces the security policy for data retrieval. Prior to
any data retrieval, it authenticates the actor attempting to access the data, and checks that the access
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
conditions as well as the life cycle state are fulfilled. It ensures that at any time, the following keys are
never readable:
- Personalization Agent keys
- MSK and LSK
- Chip Authentication keys,
- The signature keys
It controls access to the CPLC data as well:
- It ensures the CPLC data can be read during the personalization phase
- It ensures it cannot be readable without authentication at the end of the personalization
step
If the SCD is deleted, no data related to it can be accessed anymore.
In operational use phase, the three functionalities of the eSign application can only be accessed with the
corresponding authorization. These functionalities are RAD management, Signature Key management and
Signature creation. The access control to these three functions is assured by executing the Authentication
Procedure (see 3.2.6.4) proving the possession of the necessary rights.
Access Control in writing
This function controls access to write functions (in EEPROM) and enforces the security policy for data
writing. Prior to any data update, it authenticates the actor, and checks that the access conditions as well
as the life cycle state are fulfilled. It also ensures that the CPLC data (data uniquely identifying the chip) can
not be written anymore once the TOE is personalized and that it is not possible to load or modify an
additional code. It ensures that the DTBS cannot be altered.
If the RAD is blocked, the function insures that no writing of any data is possible anymore in operational use
phase.
In operational phase, the three functionalities of the eSign application can only be accessed with the
corresponding authorization. These functionalities are RAD management, Signature Key management and
Signature creation. The access control to these three functions is assured by executing the Authentication
Procedure (see 3.2.6.4) proving the possession of the necessary rights.
Signature Creation
This functionality provides the following functions:
- Sign Data (PERFORM SECURITY OPERATION Command) with RSA or Elliptic Curve keys such that the
SCD cannot be reverse-engineered from a known signature and the integrity of the DTBS is assured.
For a signature to be created, the Signature Creation functionality assures that
- the user has successfully authenticated with the rights required for R.Sigy,
- the SCD is operational,
- the integrity of the card data and the DTBS has been confirmed.
This security functionality manages the signature computation respecting the rights corresponding with
[R5].
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
Signature Key Management
This functionality provides the following functions:
- Generate Key (GENERATE ASYMMETRIC KEY PAIR Command) only by an authorized user.
- Terminate Key (TERMINATE Command)
It ensures the correspondence and uniqueness of SVD and SCD.
It controls access to the Signature keys SVD/SCD, depending on the roles (User, Admin).
RAD Management
The modification and creation rights of the RAD depending on the roles (Sigy, Admin) are enforced by this
function.
This functionality provides the following functions:
- Set PIN (CHANGE REFERENCE DATA Command)
- Verify PIN (VERIFY PIN Command)
- Change PIN (CHANGE REFERENCE DATA Command)
- Unblock PIN (RESET RETRY COUNTER Command)
- Terminate PIN (TERMINATE Command)
- Activate PIN (ACTIVATE PIN Command)
- Deactivate PIN (DEACTIVATE PIN Command)
It is used to verify the will of the Signatory to sign data.
Physical protection
This security functionality protects the TOE against physical attacks so that the integrity and confidentiality
of TOE data is ensured, including the SCD, the DTBS, the RAD, the CPLC and the TOE ID. It detects physical
tampering, responds automatically, and also controls the emanations sent out by the TOE.
Secure state management
This security functionality ensures that the TOE gets back to a secure state when
- an integrity error is detected during self-testing (including detection of corrupted data or physical
tampering),
- a tearing occurs (during a copy of data in EEPROM).
This security functionality ensures that if such a case occurs, the TOE is either switched to the state "kill
card" or becomes mute. This includes assuring the atomic activation of additional code.
Self-tests
The TOE performs self-tests to verify the integrity of the TSF data:
- Before the TSF data usage
- The additional code integrity is checked at each POWER ON of the card
- The integrity of keys and sensitive data is ensured (including the DTBS and the TOE ID)
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
11 RATIONALES
11.1 Security objectives and Security Problem Definition
11.2 Security objectives rationale
11.2.1 Security objectives backtracking
The columns and lines with green background are the elements added to the PP SSCD-2.
OT.Lifecycle_Security
OT.SCD/SVD_Auth_Gen
OT.SCD_Unique
OT.SCD_SVD_Corresp
OT.SCD_Secrecy
OT.Sig_Secure
OT.Sigy_SigF
OT.DTBS_Integrity_TOE
OT.EMSEC_Design
OT.Tamper_ID
OT.Tamper_Resistance
OT.Secure_Load_ACode
OT.Secure_AC_Activation
OT.TOE_Identification
OT.Pre_Perso
OT.Perso
OE.CGA_QCert
OE.SVD_Auth
OE.SSCD_Prov_Service
OE.HID_VAD
OE.DTBS_Intend
OE.DTBS_Protect
OE.Signatory
T.SCD_Divulg X
T.SCD_Derive X X
T.Hack_Phys X X X X
T.SVD_Forgery X X
T.SigF_Misuse X X X X X X X
T.DTBS_Forger
y
X X X
T.Sig_Forgery X X X
T.Unauthorized
_Load
X
T.Bad_Activati
on
X
T.TOE_Identifi
cation_Forgery
X
T.Pre_Perso
X
T.Perso
X
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
OT.Lifecycle_Security
OT.SCD/SVD_Auth_Gen
OT.SCD_Unique
OT.SCD_SVD_Corresp
OT.SCD_Secrecy
OT.Sig_Secure
OT.Sigy_SigF
OT.DTBS_Integrity_TOE
OT.EMSEC_Design
OT.Tamper_ID
OT.Tamper_Resistance
OT.Secure_Load_ACode
OT.Secure_AC_Activation
OT.TOE_Identification
OT.Pre_Perso
OT.Perso
OE.CGA_QCert
OE.SVD_Auth
OE.SSCD_Prov_Service
OE.HID_VAD
OE.DTBS_Intend
OE.DTBS_Protect
OE.Signatory
P.CSP_QCert X X X
P.QSign X X X X
P.SigySSCD X X X X X X X X X X
P.Sig_Non-
Repud
X X X X X X X X X X X X X X X X
A.CGA X X
A.SCA X
Table 11-1 - Mapping of security problem definition to security objectives
11.2.2 Security objectives sufficiency
The rationales are available in the complete ST.
11.3 Security requirements and security objectives
11.3.1 Rationale tables of Security Objectives and SFRs
OT.Lifecycle_Security
OT.SCD/SVD_Auth_Gen
OT.SCD_Unique
OT.SCD_SVD_Corresp
OT.SCD_Secrecy
OT.Sig_Secure
OT.Sigy_SigF
OT.DTBS_Integrity_TOE
OT.EMSEC_Design
OT.Tamper_ID
OT.Tamper_Resistance
OT.Secure_Load_ACode
OT.Secure_AC_Activation
OT.TOE_Identification
OT.Pre_Perso
OT.Perso
FCS_CKM.1/RSA X X X X
FCS_CKM.1/ECDSA X X X X
FCS_CKM.4 X X X
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
OT.Lifecycle_Security
OT.SCD/SVD_Auth_Gen
OT.SCD_Unique
OT.SCD_SVD_Corresp
OT.SCD_Secrecy
OT.Sig_Secure
OT.Sigy_SigF
OT.DTBS_Integrity_TOE
OT.EMSEC_Design
OT.Tamper_ID
OT.Tamper_Resistance
OT.Secure_Load_ACode
OT.Secure_AC_Activation
OT.TOE_Identification
OT.Pre_Perso
OT.Perso
FCS_COP.1 X X
FDP_ACC.1/SCD/SVD_Generat
ion
X X
FDP_ACC.1/SVD_Transfer X
FDP_ACC.1/Signature_Creatio
n
X X
FDP_ACF.1/SCD/SVD_Generati
on
X X
FDP_ACF.1/SVD_Transfer X
FDP_ACF.1/Signature_Creatio
n
X X
FDP_RIP.1 X X
FDP_SDI.2/Persistent X X X X X
FDP_SDI.2/DTBS X X
FIA_AFL.1 X
FIA_UAU.1 X X
FIA_UID.1 X X X X
FMT_MOF.1 X X
FMT_MSA.1/Admin X X
FMT_MSA.1/Signatory X X
FMT_MSA.2 X X X
FMT_MSA.3 X X X
FMT_MSA.4 X X X X
FMT_MTD.1/Admin X X
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
OT.Lifecycle_Security
OT.SCD/SVD_Auth_Gen
OT.SCD_Unique
OT.SCD_SVD_Corresp
OT.SCD_Secrecy
OT.Sig_Secure
OT.Sigy_SigF
OT.DTBS_Integrity_TOE
OT.EMSEC_Design
OT.Tamper_ID
OT.Tamper_Resistance
OT.Secure_Load_ACode
OT.Secure_AC_Activation
OT.TOE_Identification
OT.Pre_Perso
OT.Perso
FMT_MTD.1/Signatory X X
FMT_SMR.1 X X X X
FMT_SMF.1 X X X X X
FPT_EMS.1 X X X X
FPT_FLS.1 X
FPT_PHP.1 X X X
FPT_PHP.3 X X X X
FPT_TST.1 X X X X
FAU_STG.2/MP_Add_code X X X
FCS_CKM.1/MP_Add_code X
FCS_COP.1/MP_ENC_Add_cod
e
X
FCS_COP.1/MP_MAC_Add_co
de
X
FDP_UIT.1/MP_Add_code X X X
FMT_MTD.1/MP_Add_code X
FMT_MTD.1/MP_KEY_READ_
Add_code
X X X
FMT_SMR.1/MP_Add_code X
FPT_EMS.1/MP_Add_code X X X
FTP_ITC.1/MP_Add_code X X
FCS_CMK.1/MP X
FCS_COP.1/MP_ENC_3DE
S
X X X
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
OT.Lifecycle_Security
OT.SCD/SVD_Auth_Gen
OT.SCD_Unique
OT.SCD_SVD_Corresp
OT.SCD_Secrecy
OT.Sig_Secure
OT.Sigy_SigF
OT.DTBS_Integrity_TOE
OT.EMSEC_Design
OT.Tamper_ID
OT.Tamper_Resistance
OT.Secure_Load_ACode
OT.Secure_AC_Activation
OT.TOE_Identification
OT.Pre_Perso
OT.Perso
FCS_COP.1/MP_ENC_AE
S
X X X
FCS_COP.1/MP_MAC_3D
ES
X X X
FCS_COP.1/MP_MAC_AE
S
X X X
FCS_COP.1/MP_AUTH_3D
ES
X X X
FCS_COP.1/MP_AUTH_AE
S
X X X
FCS_COP.1/MP_SHA X X X
FDP_ACC.2/MP X X
FDP_ACF.1/MP X X
FDP_ITC.1/MP X X
FDP_UCT.1/MP X X
FDP_UIT.1/MP X
FIA_AFL.1/MP X X
FIA_UAU.1/MP X
FIA_UID.1/MP X
FIA_UAU.4/MP_3DES X X X
FIA_UAU.4/MP_AES X X X
FIA_UAU.5/MP_3DES X X
FIA_UAU.5/MP_AES X X
FMT_MTD.1/MP X X
FTP_ITC.1/MP X X
FMT_MTD.1/MP_INI_ENA X X
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
OT.Lifecycle_Security
OT.SCD/SVD_Auth_Gen
OT.SCD_Unique
OT.SCD_SVD_Corresp
OT.SCD_Secrecy
OT.Sig_Secure
OT.Sigy_SigF
OT.DTBS_Integrity_TOE
OT.EMSEC_Design
OT.Tamper_ID
OT.Tamper_Resistance
OT.Secure_Load_ACode
OT.Secure_AC_Activation
OT.TOE_Identification
OT.Pre_Perso
OT.Perso
FMT_MTD.1/MP_INI_DIS X X
FMT_MTD.1/MP_KEY_READ X X
FMT_MTD.1/MP_KEY_WRITE X X
FAU_SAS.1/MP X
FMT_SMF.1/MP X X X
FMT_SMR.1/MP X X X
FPT_EMS.1/MP X X X X
Table 11-2 - SFR vs Objectives
11.3.2 Rationale of Security Objectives and SFRs
The rationales are available in the complete ST.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
12 REFERENCES
Specifications
[R1] DIRECTIVE 1999/93/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 13 December 1999
on a Community framework for electronic signatures
[R2] ICAO Doc 9303, Machine Readable Travel Documents, part 1 – Machine Readable Passports, Sixth
Edition, 2006, International Civil Aviation Organization
[R3] BSI TR-03110 V2.10 Part 1 eMRTDs with BAC/PACE
[R4] BSI TR-03110 V2.10 Part 2 Extented Access Control Version 2 (EACv2), Password Authenticated
Connection Establishment (PACE), and Restricted Identification (RI)
[R22] BSI TR-03110 V2.10 Part 3 Common Specifications
[R23] BSI TR-03117 V1.0 eCard with contactless interface as a secure signature creation device
Oberthur Specifications
[R15] SRS Auth and Key Management – 079711 00 – Oberthur Technologies
Protection Profiles
[R9] Information Technology - Personal Identification — ISO Compliant Driving Licence — Part 3: Access
control, authentication and integrity validation, ISO/IEC 18013-3:2009
[R26] Smartcard IC Platform Protection Profile v 1.0 - BSI-PP-0035 15/06/2007
[R27] Machine readable travel documents with “ICAO Application”, Basic Access control – BSI- PP-0055
v1.10 25th march 2009
[R28] Machine readable travel documents with “ICAO Application”, Extended Access control – BSI-PP-0056
v1.10 25th march 2009
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
[R29] Machine readable travel documents with “ICAO Application”, Extended Access Control with PACE
(EAC PP) – BSI-PP-0056 V2 – 2012
[R33] Technical Report, Supplemental Access Control for Machine Readable Travel Documents – version
v1.01
Chips References
[R35] Certification report - BSI-DSZ-CC-0837-v2-2014 - NXP Secure Smart Card Controller Controller
P60x080/052/040PVC(Y/Z/A)/PVG with IC Dedicated Software
Standards
[R36] ISO/IEC 7816-4:2013 – Organization, security and commands for interchange
[R37] ISO/IEC 7816-8:2004 – Commands for security operations
[R41] ISO/IEC 9796-2:2002 - Information technology - Security techniques - Digital signature schemes giving
message recovery - Part 2: Mechanisms using a hash-function
[R43] Federal Information Processing Standards Publication 180-2 Secure Hash Standard (+ Change Notice
to include SHA-224), U.S. DEPARTMENT OF COMMERCE/National Institute of Standards and Technology,
2002 August 1
[R48] FIPS 46-3 Data Encryption Standard (DES)
[R51] FIPS 197 – Advance Encryption Standard (AES)
CC
[R58] Common Criteria for Information Technology security Evaluation Part 1: Introduction and general
model, CCMB-2012-09-001, version 3.1 Revision 4 Final, September 2012
[R59] Common Criteria for Information Technology security Evaluation Part 2: Security Functional
Components, CCMB-2012-09-002, version 3.1 Revision 4 Final, September 2012
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
[R60] Common Criteria for Information Technology security Evaluation Part 3: Security Assurance
Components, CCMB-2012-09-003, version 3.1 Revision 4 Final, September 2012
[R61] ANSSI-CC note 6 – v0.91
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
13 ACRONYMS
CA Chip Authentication
CC Common Criteria
CPLC Card Personalization Life Cycle
DGA Certificate Generation Application
DES Digital Encryption Standard
DTBS/R Data to be signed or its unique representation
EAC Extended Access Control
EAL Evaluation Assurance Level
EF Elementary File
IC Integrated Circuit
LSK Load Secret Key (Key for Loading of Additional Code)
MRTD Machine Readable Travel Document
MSK Manufacturer Secret Key
PP Protection Profile
RAD Reference Authentication Data. Could be a PIN or a Biometric password.
SCA Signature Creation Application
SCD Signature Creation Data
SDO Signed Data Object
SHA Secure Hashing Algorithm
SFP Security Function Policy
SSCD Secure Signature Creation Device
ST Security Target
SVD Signature verification data
TA Terminal Authentication
TOE Target Of Evaluation
TSF TOE Security Functionality
VAD Verification Authentication Data. Could be a PIN or a Biometric password.
ID-One eIDAS v1.0 in SSCD-2 configuration
Public Security Target - FQR 110 7792 Is 3
T. +33 (0)1 78 01 70 00 I F. +33 (0)1 78 01 70 20 I Oberthur Technologies - 420, rue d’Estienne d’Orves - 92700 Colombes - France I info@oberthur.com
S.A. AU CAPITAL de 22 310 409,20€ - RCS NANTERRE 340 709 534
14 LIST OF TABLES AND FIGURES
Figures
Figure 1 - Product architecture ........................................................................................................................13
Figure 2 - Product architecture with TOE components....................................................................................16
Figure 3 - TOE Lifecycle.....................................................................................................................................20
Tables
Table 1-1 - General Identification.....................................................................................................................11
Table 1-2 - TOE technical identification ...........................................................................................................11
Table 1-3 - Chip Identification..........................................................................................................................12
Table 2-1 - eSign Configurations ......................................................................................................................14
Table 4-1 - Roles identification on the life cycle ..............................................................................................21
Table 4-2 - Subjects identification following life cycle steps............................................................................21
Table 5-1 - Conformance Claim........................................................................................................................25
Table 5-2 - Conformance with SSCD-2 PP (SPD and Objectives)......................................................................27
Table 5-3 - Conformance with SSCD-2 PP (SFR) ...............................................................................................29
Table 11-1 - Mapping of security problem definition to security objectives...................................................74
Table 11-2 - SFR vs Objectives..........................................................................................................................78